Abstract
Opalinus Clay is considered a potential host rock for radioactive waste disposal. The Jurassic claystone formation is composed of several facies and subfacies types, which are characterized by varying amounts of quartz, carbonates (cements and fossils) and clay minerals. To provide samples for ongoing experimental and numerical studies, a complete core section was drilled in the Mont Terri rock laboratory. The lithological and structural variability (including tectonic fault structures) from borehole BAD-2 was investigated using a multidisciplinary approach including high-resolution geoelectric in situ borehole measurements, mineralogical/geochemical and (micro)structural analyses.
The lithological–compositional variability was captured by successfully applying a modified subfacies approach, which is independently confirmed by the geochemical data and ERT (Electrical Resistivity Tomography) measurements. The variability on the cm to dm scale perpendicular to bedding can be determined based on the mean resistivity and variation of amplitude. In particular, the facies transitions could be precisely located. The new results suggest that both shaly facies types form the homogenous part of the investigated section, whereas the sandy facies and especially the carbonate-rich sandy facies represent the more heterogeneous lithofacies types of the Opalinus Clay. The varying resistivity can be attributed to differences in clay mineral and carbonate content. Regarding the structural variability, brittle faults were observed with varying frequency throughout the investigated section. Most fault planes occur in the shaly facies types, some of them concentrate along heterogeneities on the subfacies scale. The striking reproducibility of the measurements and observations was confirmed by a comparison with boreholes drilled in parallel, indicating a rather low compositional–structural variability parallel to bedding. The applied multidisciplinary approach is well suited to depict the vertical and lateral variability of a claystone formation, allowing an assessment of the degree of homogeneity/heterogeneity based on the subfacies concept.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
In countries, such as Switzerland, Germany and France, shale formations are considered potential host rocks for radioactive waste disposal. However, claystone exhibits a complex thermo-hydro-mechanical-chemical (THMC) coupling of many properties that are relevant for their barrier behavior. To address some of these issues, the Federal Institute for Geosciences and Natural Resources (BGR) perform experiments and measurements in the Swiss Mont Terri rock laboratory, which is located in the Jurassic Opalinus Clay (Bossart et al. 2017; Schuster et al. 2019). Furthermore, the study of Opalinus Clay is of great interest due to its properties that are representative for a barrier rock. It is also a crucial constituent for numerous potential applications in the oil and gas industry, in particular the storage of hydrocarbons or CO2 and for the safe disposal of high-level radioactive waste.
Rocks may show discontinuities, such as sedimentary structures and lithostratigraphic transitions towards heterogeneities including sand or carbonate layers and tectonic faults or fractures. Such discontinuities may have a large impact on the in situ stress state and on hydraulic and frictional properties (Minardi et al. 2016; Orellana et al. 2018a, b, 2019; Crisci et al. 2019). Fluids may penetrate along active fault zones and influence rock properties even at depths of several kilometers (e.g. Nesbitt and Muehlenbachs 1989; Zulauf et al. 1999; Boles et al. 2015). The multibarrier concept in claystone relies (amongst others) on the low hydraulic conductivity, the sorption properties and the fracture-sealing capabilities of the potential host rock formation. These properties depend on the mineralogical composition and the spatial distribution (rock fabric) of these constituents (Klinkenberg et al. 2009; Kaufhold et al. 2013; An et al. 2020; Zhang and Laurich 2020). A detailed characterization of discontinuities, heterogeneities and their lithological composition is therefore of high importance.
The primary aim of the two fully cored research drillings “AD” in the Mont Terri rock laboratory was to provide core samples for the collaborative BMBF-project “GeomInt” (Geomechanical Integrity of Host and Barrier Rocks – Experiment, Modeling and Analysis of Discontinuities). The focus of this project are experimental–numerical analyses of the formation and development of discontinuities in rock salt, claystone and crystalline rocks (Kolditz et al. 2021). In addition to the sampling campaign for GeomInt, a multidisciplinary approach was applied to provide a detailed geological–geophysical characterization of the drill cores. The task was to characterize the rock units that had been drilled through, to precisely determine the locations of facies boundaries and to quantify the intra-facies variability. For this purpose (micro)structural and mineralogical–geochemical investigations were combined with borehole-based electrical resistivity tomography (ERT) measurements. To quantify the lateral variability, the results were compared to other boreholes of similar orientation and location (Fig. 1).
There are few attempts to systematically characterize intra-formational heterogeneity of claystone formations. In this context, the subfacies classification developed by Lauper et al. (2018) provides a framework for a detailed characterization of lithological intra-facies variations for the Opalinus Clay. For this approach, microstructural investigations are essential, as they provide information regarding the compositional–structural variability (e.g. Laurich et al. 2014; Kneuker et al. 2017), which are confirmed by the mineralogical–geochemical analyses, ideally applied in combination (e.g. Clauer et al. 2017; Kneuker et al. 2020). In addition, the BGR develops borehole tools with a high spatial resolution for in situ derived geophysical and geotechnical parameters. Especially ERT measurements have the capacity to characterize structures close to the borehole and to resolve rock variability with high accuracy. This, in combination with the introduction and standardization of the subfacies concept, will allow a more precise choice of claystone samples, e.g. for the experimental determination of parameters.
Geological setting
The Jurassic Opalinus Clay consists of dark grey argillaceous to light grey silty-sandy claystones that are subdivided into several lithostratigraphic units based on varying quantities of clay minerals, quartz and carbonates (Bläsi et al. 1996; Bossart and Thury 2008; Hostettler et al. 2017; Lauper et al. 2018). From the lowest to the uppermost stratigraphic position, these facies types include the lower shaly facies (shaly facies 1), the carbonate-rich sandy facies, the lower sandy facies (sandy facies 1), the upper shaly facies (shaly facies 2) and the upper sandy facies (sandy facies 2; not covered by the present study). Carbonates occur in the claystones either as biodetritus/fossils or as diagenetic cements, especially in the two sandy facies types. The Opalinus Clay was deposited in a shallow marine, epicontinental environment at the level of the storm wave base at ca. 20 m to 50 m water depth (Wetzel and Allia 2003). During Cretaceous burial, the Opalinus Clay experienced maximum palaeo-temperatures of 75 °C to 90 °C at a maximum burial depth of 1.35 km (Mazurek et al. 2006).
When compared with other Mesozoic rock formations, the Opalinus Clay is a macroscopically homogeneous formation with rather small lithological variability (this applies in particular to the shaly facies 1). On the cm to dm scale, however, several structural and compositional heterogeneities become evident. An example of a structural heterogeneity at the m scale is the Main Fault structure, outcropping in the Mont Terri rock laboratory (see below). The preferred alignment of phyllosilicates is related to bedding, which causes anisotropic hydraulic and mechanical properties (e.g. Gautschi 2017).
The Opalinus Clay investigated in this study originates from the Mont Terri rock laboratory, which is located next to the village of St. Ursanne in NW Switzerland. The total thickness of the Opalinus Clay in this area is ca. 130 m. The layers are dipping with ca. 45° towards SE. At the drilling site of the borehole BAD-2, the overburden amounts to 250 m (Fig. 1).
The rock laboratory is located within the southern fold limb of the NW-vergent Mont Terri anticline structure, in a special tectonic setting at the crossing of several structural elements, including the frontal part of the Jura fold belt and the roughly N–S trending Rhine–Bresse zone. For details, see Nussbaum et al. (2011, 2017). Individual faults are commonly encountered throughout the rock laboratory (Jaeggi et al. 2017, 2020). A 1–3 m thick fault zone (“Main Fault”) that is bounded by major fault planes including scaly clay and fault gouge was investigated in detail by several authors (Nussbaum et al. 2011; Laurich et al. 2014; Jaeggi et al. 2017; Kneuker et al. 2017). The inferred fault displacement is in the range of decameters. The relationship between fluid injection and fault displacement was investigated by an in situ experiment (Guglielmi et al. 2017; Jeanne et al. 2018). An injection pressure of ca. 4 MPa led to a reactivation of the tested faults in the sub-mm range and a simultaneous transmissivity increase. In this context, Orellana et al. (2018a; b; 2019) conducted systematic laboratory studies regarding the frictional strength, mechanical stability, dilatancy and permeability of intact Opalinus Clay and simulated Opalinus Clay gouge.
Work towards a detailed litho- and biostratigraphical characterization of the rock sequence in the Mont Terri rock laboratory has been intensified in the last few years (e.g., Müller and Jaeggi 2012; Jaeggi et al. 2014; Reisdorf et al. 2014; Hostettler et al. 2017; Lauper et al. 2020). In addition to the established main lithofacies types Müller and Jaeggi (2012) and Lauper et al. (2018) introduced several subunits (subfacies types) to allow a consistent lithological classification of the Opalinus Clay. In our study, we present the results from (micro)structural investigations, geophysical borehole logging and the corresponding mineralogical–geochemical analysis. The aim is to characterize the small-scale lithological variability of the Opalinus Clay at high resolution by applying the subfacies concept (Lauper et al. 2018), including observations on brittle faults encountered in the different facies and subfacies types. To further validate the findings, the petrographic results were correlated with mineralogical–geochemical data and geoelectrical in situ borehole measurements.
Sample material
The two fully cored research boreholes (BAD-1 and BAD-2) with a hole diameter of 131 mm (resulting in a core diameter of 101 mm) were drilled parallel (BAD-1) and perpendicular (BAD-2) to the sedimentary bedding, respectively. The 15.35-m long horizontal borehole BAD-1 was drilled in July 2018 and is located entirely in the lower sandy facies (sandy facies 1). This drill core is not part of the present study, as it was sampled in its entire length for a different experimental campaign of the GeomInt project (Kolditz et al. 2021). The BAD-2 borehole has a length of 27.0 m and was drilled in May 2019. The borehole is oriented perpendicular to the bedding (with a dip of 43°); thereby, crossing several important facies transitions of the Opalinus Clay (Fig. 1). The geological onsite mapping by swisstopo (Galletti and Jaeggi 2019) revealed the following stratigraphic sequence:
-
0.00 m to 4.75 m depth: upper shaly facies (shaly facies 2),
-
4.75 m to 19.40 m depth: lower sandy facies (sandy facies 1),
-
19.40 m to 24.57 m depth: carbonate-rich sandy-facies,
-
24.57 m to 27.00 m depth: lower shaly facies (shaly facies 1).
The BAD-2 drill core was sampled from 4.0 m to 14.8 m (mainly sandy facies 1) for laboratory experiments of the GeomInt project. The core samples were conditioned in aluminum foil and pressurized in special nitrogen-filled BGR-liners (autoclaves) to avoid further alteration (as compared to Kaufhold et al. 2013). The cores allowed to study the important lithostratigraphic transition from the shaly facies 1 towards the carbonate-rich sandy facies (transition zone 1) and the so far poorly investigated transition from the carbonate-rich sandy facies towards the sandy facies 1 (transition zone 2). The drill core material from the intervals between 0.0 m to 4.0 m and 14.8 m to 27.0 m has been investigated at the BGR core repository in Hannover (Germany).
Methods
Sampling
On site, the nonoriented drill cores were first described visually. Sampling for thin sections and mineralogical–geochemical analyses was performed as indicated in Fig. 2. Samples for mineralogical–geochemical investigations and thin section analyses were collected perpendicular to bedding (S0) and sealed air and gas tight in special coated aluminum foil in order to prevent artificial alteration, especially a drying/dewatering of the sample material.
Samples for thin and polished section analysis were cut from 3 to 4 cm thick core disks, sampling for mineralogical–geochemical analyses were performed on ca. 2 cm thick core disks, to adequately capture the observed compositional variability at the subfacies scale. Approximately, 20 g of sample material was pulverized in a ring and puck-mill to powder with a particle size < 40 μm. For thin and polished sections, samples were carefully dry cut to avoid the formation of artificial microcracks and to prevent contamination with liquids. Fragile samples were impregnated with epoxy resin to prevent break-up and to further stabilize the sample during the preparation process.
Microfabric and structural studies
To investigate the microfabrics in the claystone samples, polished thin and thick sections were analyzed under transmitted and reflected light using a Leica DMRM polarization microscope. Optical polarization microscopes were used for structural analysis of the claystone in the mm to µm scale. Polished sections were investigated using a high-resolution scanning electron microscope (SEM). For the present study, a Quanta 600 F in low vacuum mode (0.6 mbar) with an acceleration voltage of 20.0 kV in backscatter mode was used. This SEM is equipped with the EDX detector system Apollo XL. The EDX detector has a spatial resolution of around 5 µm.
Mineralogical–geochemical analyses
The mineral phases of the claystone samples were analyzed using X-ray powder diffraction (XRD). A PANalytical MPD Pro with Bragg–Brentano geometry including a fine-structure copper tube was used. The apparatus is equipped with a variable divergence slit (20 mm irradiated length), a X´Celerator detector (active length 0.59°) and a sample changer. By default, the samples consist of 1–2 g fine powder (< 40 µm). Depending on the analyzed phase, the detection limit ranges from 1–5 wt%. For analytical details, see Ufer et al. (2012).
X-ray fluorescence analysis (XRF) was used to quantify chemical elements from an atomic number of 9 (fluorine) upwards. The detection limit varies between 0.01 wt% and 1 wt% for major components and between 1 ppm and 30 ppm for trace elements. Before the analysis, the quantification of volatile constituents was carried out by heating of 1 g sample material at T = 1030 °C for 10 min (loss on ignition, LOI). The sequential determination of 10 major and 31 trace elements was performed using a PANalytical Axios WD-XRF spectrometer, equipped with a rhodium source. For further details of the analytical procedure, see Reimann et al. (2014).
The determination of cation exchange capacity (CEC) was carried out according to the method of Meier and Kahr (1999), after calcite saturation of the sample material, based on a Cu(II)triethylentetramine complex (“Cu-trien method”). This parameter is a measure of smectite content, such as illite–smectite mixed layers (Frederickx et al. 2018). For the determination of cation exchange capacity around 1 g of sample material is required. According to Dohrmann et al. (2012), the analytical error for high-CEC bentonites is generally better than ± 3.9 cmol( +)kg−1, for natural Opalinus Clay the corresponding errors are likely to be lower.
Geoelectric borehole measurements (ERT)
To reveal the spatial resistivity distribution along the borehole axis, direct current geoelectrical measurements were performed using the high-resolution earth resistivity meter 4-point light 10 W (Lippmann Geophysikalische Messgeräte), controlled by the software GeoTest (Geophysik–Dr. Rauen). In this setup, the BGR borehole probe GB100-15 provides the necessary electric contact to the borehole wall. It consists of 100 electrodes with a spacing of 15 mm (Fig. 3b). For the measurements in adjacent boreholes BGC-2 and BWS-I2, the GB50-15 borehole probe with 50 electrodes and an electrode distance of 15 mm was used (Fig. 3a). Both tools have a diameter of 80 mm (for typical hole diameters of 86 mm), but greater diameters can be adapted. The electrodes can be extended pneumatically for the required connection to the borehole wall. The spatial resolution is limited by 2 × the electrode distance (30 mm), the maximum depth of investigation is about 30 cm perpendicular to the borehole wall. The chosen electrode configuration represents a Wenner-α setup.
The measurements commence at the tunnel surface. Because of the shotcrete lining, the first measured point is located at a borehole depth of 10 cm. The probe is moved progressively down the borehole in distinct steps of 75 cm length. This results in a half side overlapping of the geoelectrical pseudosections (Fig. 3c). The measurements on borehole BAD-2 were performed in May 2019. Since the borehole is oriented perpendicular to the bedding, measurements were only taken in one orientation (0°, i.e. the electrodes are oriented upwards). A total of 35 individual profiles with half-sided overlapping were mapped.
A numerical inversion process is necessary for data analysis and interpretation. The measured apparent resistivities along the borehole are thus transformed into a spatial model, discretized into a distinct number of elements of homogeneous resistivity, taking into account the electrode geometry. The forward operator in the inversion process is generally obtained by finite-difference (FD) or finite-element (FE) methods. For our data, the non-commercial software package BERT (Boundless Electrical Resistivity Tomography) developed by Th. Günther (Leibniz Institute of Applied Geophysics, Hannover) and C. Rücker (Technical University of Berlin) is used (https://gitlab.com/resistivity-net/bert). For further details, see Günther et al. (2006) and Rücker et al. (2006).
Results
Petrography
The investigated drill cores capture two of the five major facies types of the Opalinus Clay completely and two facies types partially (Figs. 1 and 2). For the present study, we applied the classification of subfacies types (SF) according to Lauper et al. (2018) including the newly defined subfacies type SF2a (see below). Each subfacies type is characterized by a distinctive color, grain size, (micro)fabric and lithology (Fig. 4).
From stratigraphic base to top (against the direction of drilling), the shaly facies 1 was encountered between 27.00 m and 24.57 m depth (Fig. 2). This facies type consists of homogenous, dark grey calcareous to silty-sandy mudstones including mica, pyrite and accumulations of biodetritus (Fig. 5a). The clay fraction is visible in thin sections as a fine-grained, brownish matrix, including up to 25 µm-sized flakes of muscovite and isolated quartz grains. Silty-sandy, detrital components are angular to subrounded quartz and feldspar with a grain size between 5 µm and 15 µm. Framboidal pyrite occurs irregularly distributed in the clay-rich matrix or locally clustered (pyritizied burrow structures). The shaly facies 1 is the most homogenous facies type of the investigated section. Here, in accordance with Lauper et al. (2018), only subfacies type SF1 was observed (see Fig. 2).
The base of the first carbonate layer is defined as the onset of the carbonate-rich sandy facies. This sharp lithostratigraphic transition towards the overlying carbonate-rich sandy facies is formed by light grey, flaser-bedded to homogenous calcareous–siliceous layers (SF4) with few argillaceous–siliceous mudstone layers (SF2) between 24.57 m and 23.90 m drill core depth (transition zone 1). Larger fossil (echinoderm) remains and pyrite nodules are commonly found in this interval. The carbonate-rich sandy facies (from 24.57 m to 19.40 m) includes dark grey, moderately to strongly bioturbated, calcareous, silty-sandy mudstone layers alternating with cm to dm thick, light-grey calcareous–siliceous lenses and layers. The latter consist of silt- to fine-sand-sized detrital quartz (grain size > 80 µm) and include abundant bioclastic fragments up to 2 cm in size (Fig. 5f). The carbonate-rich sandy facies is the most heterogeneous facies type at the Mont Terri site due to the contrasting occurrence of the argillaceous–siliceous subfacies type SF2 and both carbonate dominated subfacies types SF4 and SF5.
The more gradual transition from the carbonate-rich sandy facies towards the sandy facies 1 is located in borehole BAD-2 between 19.56 m and 17.85 m (transition zone 2). The transition is marked by thicker, medium to light grey, homogenous siliceous–calcareous bioclast-rich beds (SF4) with few argillaceous or siliceous interlayers (SF2 and SF3). The carbonate content is decreasing in favor of silty-sandy lenses and layers. In contrast to transition zone 1, pyrite nodules were not found in this interval. The sandy facies 1 is located in borehole BAD-2 between 19.40 m and 4.75 m (Fig. 2). This facies is composed of calcareous, silty-sandy mudstones alternating with numerous light grey, bedded or laminated sandstones and distinct biodetritus-rich layers or lenses (Fig. 5b). Sand layers can have thicknesses of one mm up to several cm. Silty-sandy quartz grains (grain sizes around 40–50 µm) are commonly cemented by carbonates, however, albeit the cementing is not always continuous (Fig. 5c). In the sandy facies 1 the subfacies types SF2, SF3 and SF4 were observed. The gradual transition towards the overlying shaly facies 2 is characterized by a decrease of the lenticular-laminated subfacies type 3.
The shaly facies 2 (4.75 m to 0.00 m) is characterized by a dark grey, argillaceous to silty mudstone containing mica, pyrite and quartz grains with grain size between 20 and 35 µm. This mudstone is intercalated with light grey, mm to cm thick silt layers (Fig. 5d), which are not continuously cemented with calcite. When compared with the shaly facies 1, the shaly facies 2 shows a higher amount of silt-grained clastic components and less biodetritic fragments (Fig. 5e). Disseminated pyrite occurs throughout the clay-rich intervals. In the shaly facies 2 the clay-rich subfacies types SF2 and SF2a were observed. The subfacies type 2a (SF2a) has been newly defined in the present study; it consists of a dark gray, sparsely bioturbated, planar–parallel-laminated, argillaceous–siliceous medium-grained mudstone (Fig. 4). It represents an intermediate type between SF1 and SF2, with fewer silt-rich laminaes when compared with SF2.
Structural record
Brittle faults were observed with different frequency in all facies types. Most fault planes occur in the shaly facies 1 and 2, with a high fault density of 6–9 m−1 for the latter (Fig. 6g). The artificial fracture pattern of the excavation damaged zone (EDZ) was observed up to 1.5 m borehole depth (Fig. 6a). In this interval, slickensides of shear fractures and plumose structures (indication for artificial tensile fractures) are visible on the joint planes of the drill cores. Fractures follow mainly the bedding plane S0 (ca. 150/45°) or cut them at a low angle of 5° to 20° (Fig. 6h). In this zone, small-scale faults including slickensides and scaly lenses were observed. This includes a debris zone at ca. 4.3 m drill core depth (Fig. 6d), where fragments with polished surfaces or striations are occurring. The shaly facies 1 shows lower fault densities (between 2 and 3 m−1), the brittle faults show a dip of 15° to 30° relative to the borehole axis. Fault surfaces in the shaly facies 1 are relatively smooth or almost perfectly planar and show a mirror-like polishing or well-developed striation with step-like elevations (risers) (Fig. 6b). At 26.75 m, a 5 mm thick calcite vein was observed in close association to a slickensided shear plane (Fig. 6c). Calcite fibers are oriented subperpendicular to the fault plane; no clear median line could be observed. The slickenside lineation on striated surfaces indicates dip-slip movements, step-like risers on fault planes point to reverse or thrust faults. Fault density decreases in the sandy facies 1 and in the carbonate-rich sandy facies type. Fault dip relative to S0 is between 0° and 15°, two faults show elevated dip angles > 30°. Discontinuity planes are more irregular. Individual faults are characterized by a more or less distinct slickenside lineation (Fig. 6f). The step-like risers show an increased height as compared to the investigated samples from the shaly facies 1 (Fig. 6e). The wavy fault surfaces reflect the imprint of underlying early diagenetic nodules and mechanically strong cemented sedimentary structures that formed during sediment compaction.
When relating fault distribution to the individual subfacies types, the trend towards a concentration of faults in the shaly intervals is confirmed: Most fault planes were observed in the clay-rich subfacies types SF1, SF2a and SF2. Even in the sandy facies 1 and the carbonate-rich sandy facies, faults are more common in SF2 than in SF3. In SF4 and SF5 no faults were observed in BAD-2. In case of the homogenous shaly facies 1, the majority of bedding parallel faults occur where no lithological heterogeneities are present. In the other facies types, faults commonly occur next to the interface between individual subfacies types, reflecting differences in mineralogical composition and material strength (Fig. 2). In this context, the debris zones near the transition from shaly facies 2 to sandy facies 1 (between 4.2 and 4.4 m) and the debris zone next to the transition from sandy facies 1 towards the carbonate-rich sandy facies at 19.8–19.9 m drill core depth can be seen. In the parallel borehole BWS-I2, a similar debris zone with fragments showing more or less developed slickensides from 12.55 to 12.80 m is present (Fig. 2). Material derived from these zones was fragmented presumably by drilling-related stress into cm sized diamond shaped chips.
Mineralogical–geochemical rock composition
Qualitative whole rock XRD analyses revealed a composition that is typical for claystones: Quartz and calcite is present as main components in all samples; detected clay minerals are illite, kaolinite and illite–smectite mixed layer minerals. Other minor constituents include chlorite, pyrite, feldspar and siderite. Gypsum as evidence for artificial alteration processes was not detected in any of the analyzed samples. In addition to these minerals, varying amounts of ankerite (calcium iron carbonate) and kutnohorite (calcium manganese carbonate) were detected in samples from the sandy facies 1 and the carbonate-rich sandy facies.
The chemical composition of the whole rock samples was determined by wavelength dispersive X-ray fluorescence analysis (XRF) and is presented as box and whisker plots (Figs. 7 and 8) for the individual facies and subfacies types. Measured values can be found in the supplementary material. The most striking trend is a steady increase in the SiO2 content from the shaly facies 1 towards the carbonate-rich sandy facies and the sandy facies 1 (Fig. 7). The shaly facies 1 and 2 are both characterized by a relatively uniform SiO2 content around 45 wt% to 55 wt%. The highest SiO2 content of 66 wt% was measured in a sample from the sandy facies 1. In contrast, the lowest value of 28 wt% SiO2 was obtained in the basal part of the carbonate-rich sandy facies (transition zone 1), documenting the dominance of carbonates in this interval (Fig. 7).
The Al2O3 content is consistently high for the shaly facies types 1 and 2. It varies on average between 17 wt% and 20 wt% for these clay-rich intervals (Fig. 7). In the investigated profiles inside the Opalinus Clay, the Al2O3 content is mainly linked to the occurrence of alumosilicates like clay minerals. For the sandy and carbonate-rich sandy facies types, the Al2O3 content varies on average between 6 wt% and 12 wt%. The most pronounced variation was recorded in the carbonate-rich sandy facies (and the two transition zones), where the content of Al2O3 varies between 4 wt% and 15 wt%. The CaO content remains relatively constant < 10 wt% for the shaly facies 1 and 2 (on average 5.3 wt%). The highest amount of CaO (33.8 wt%) was measured in a sample from the carbonate-rich sandy facies (Fig. 7). When compared with the carbonate-rich sandy facies, the sandy facies 1 has a lower averaged CaO content (10.7 wt% vs. 17.2 wt%). An increase in CaO is documented by XRF data for the base of the carbonate-rich sandy facies (transition zone 1).
The Fe2O3 content varies in a narrow span (3–6 wt%) for all facies types analyzed in the present study (Fig. 7). Slightly increased values (> 5 wt%) can be found in the shaly facies types 1 and 2, whereas values are reduced in the sandy facies 1 (< 5 wt% Fe2O3). An exception is present at the base of the carbonate-rich sandy facies (transition zone 1), where increased values between 5.0 wt% and 8.7 wt% Fe2O3 were obtained. This is consistent with the occurrence of pyrite nodules and enrichments of siderite in this interval.
MgO is elevated in both shaly facies types (around 2 wt%), whereas slightly reduced values (< 1.6 wt% MgO) occur in the carbonate-rich sandy and the sandy facies 1. This indicates that MgO is mainly restricted to the clay-rich matrix of the Opalinus Clay. An exception is the transition zone 2 at the top of the carbonate-rich sandy facies, showing increased MgO values of averaged 2.4 wt% (Fig. 7). Here, MgO occurs most probably in association with carbonate phases, as XRD analyses revealed the presence of ankerite, a mineral that includes varying amounts of MgO. In contrast to MgO, MnO is clearly bound to the carbonate-rich parts of the investigated profile (Fig. 7). The shaly facies types 1 and 2 show values < 600 ppm. Increased MnO values are present at the base and at the top of the carbonate-rich sandy facies (transition zones 1 and 2), which is consistent with the presence of kutnohorite (calcium manganese carbonate), identified by XRD analyses.
Zr shows a steady increase towards the sandy facies 1. The highest values > 320 ppm were found in the transition zone 2 (Fig. 8). This corresponds well with the petrographic observation of increased detrital input in this interval. The shaly facies 2, as compared to the shaly facies 1, shows increased Zr values (200 ppm vs. 160 ppm on average), which fits well with the occurrence of thin silt or sand layers (subfacies types SF2 and SF2a) in shaly facies 2.
The cation exchange capacity (CEC) varies within a relatively narrow range between 8.5 cmol( +)kg−1 and 11.5 cmol( +)kg−1 for the shaly facies 1. The shaly facies 2 shows comparable values of 11.8 cmol( +)kg−1 on average. In contrast, low values between 2 cmol( +)kg−1 and 5.3 cmol( +)kg−1 were measured in the sandy facies 1 (Fig. 8). Such reduced values correlate well with a low content of alumosilicates in this facies type. The carbonate-rich sandy facies shows the largest variability of all types of facies studied in the BAD-2 drill cores. Here, the CEC vary between 1.3 cmol( +)kg−1 and 7 cmol( +)kg−1, reflecting the heterogeneous composition of this facies type.
The boxplots in Fig. 8 show the content of selected elements and parameters (SiO2, Al2O3, CaO and CEC) broken down into the six subfacies types. The trends in major element composition as described above are reflected by the results summarized in Fig. 4. The decrease in Al2O3 with increasing CaO and a corresponding decrease in CEC is clearly confirmed by the data. SiO2 content is more variable and shows a slight increase from SF1 to SF2, a larger scatter in SF3 and a clear decrease in the carbonate-rich subfacies types SF4 and SF5, confirming the petrographic observation of a steady increase in carbonates for these subfacies types.
Facies-related electrical resistivity
Electrical resistivity measured in situ along the borehole BAD-2 varies by an order of magnitude, i.e. between 5.0 Ωm and 50 Ωm (Fig. 2). Up to 50 cm borehole depth, the shotcrete lining of the gallery wall can be recognized as a high-resistivity structure. Below that, the resistivity in the shaly facies 2 is ca. 5–10 Ωm. The geological investigations revealed the presence of artificial EDZ fractures to a depth of 1.5 m, which are not visible in the resistivity profile of BAD-2. From 4.7 m borehole depth onwards, the resistivity in the sandy facies 1 rises gradually up to 20 Ωm. Embedded in this basic structure are narrow layers characterized by a high resistivity up to 30 Ωm. A comparison with petrographic data reveals that high-resistivity layers correlate well with the carbonate-rich subfacies types SF4 and SF5 (Fig. 2). Sandy layers and lenses including subfacies types SF2 and SF3 show intermediate resistivity. Between 18.5 m and 19.4 m (transition zone 2, towards the carbonate-rich sandy facies) there is a striking high-resistance range (> 40 Ωm), after which the resistance level drops significantly down to 10 Ωm, again with embedded high-resistance layers. Between 23.9 m and 24.6 m (transition zone 1, towards the shaly facies 1) a second distinct high-resistance range > 40 Ωm is reached, after which a sharp drop to values < 10 Ωm can be observed. This level is maintained in the shaly facies 1 down to the bottom of the borehole without significant variation. The low resistivity can be attributed to the clay dominated subfacies type SF1 (Figs. 2 and 4).
For further analyses, resistivity curves were extracted from the calculated 2D models along the borehole axis of BAD-2. The blue graph in Fig. 9 shows the corresponding resistivity curve for a radial depth of 5 cm from the borehole wall. The positive and negative peaks in the resistivity curve can be caused by either lithological changes in the claystones (such quartz-rich sandy or carbonate interlayers) or due to fracturing and water saturation effects. A comparison with the adjacent boreholes BGC-2 and BWS-I2 revealed a good reproducibility of the geoelectric signal. BGC-2 runs parallel to borehole BAD-2 with a horizontal distance of ca. 4 m. The measurements in that borehole had been carried out almost two years earlier in September 2017 with the GB50-15 probe, which is half as long. For this reason, the radial model depths of the electrical resistivity in BGC-2 are only 20 cm. Figure 9 shows the resistivity curves for 5 cm depth perpendicular to the borehole wall for both boreholes. With few exceptions, almost the same structures were detected, especially the thicker sand layers inside the sandy facies 1 are well traceable. For resistivity curves inside the carbonate-rich sandy facies, the correlation is less distinct. In this facies type, peaks are not exactly overlapping, pointing to an increased lateral variability. However, the important facies boundaries of the carbonate-rich sandy facies (transition zones 1 and 2) are well visible in the ERT data. The same picture emerges when comparing the ERT data to the electrical resistivity measurement from the borehole BWS-I2 (Fig. 2), which was performed in March 2015.
Discussion
Interpretation of macro- and microstructures
The microstructural investigations carried out within the scope of this work show that the lithological–structural homogeneity/heterogeneity of a claystone formation, relevant for capturing the variability of thermomechanical and hydraulic properties, is mainly a question of the scale of observation. The examined claystone samples show a structural–compositional variability on the cm to dm range, occasionally up to the m range, which is reflected in both the mineralogical–geochemical and geophysical (geoelectrical) datasets. The vertical variation, subperpendicular to bedding, reflect changes in the depositional conditions (including environmental aspects and changes in sea level) and diagenetic processes through time (Lauper et al. 2018, 2020).
Two end members characterize the investigated facies types of Opalinus Clay: The clearly homogenous shaly facies 1 and the much more heterogeneous carbonate-rich sandy facies, which differ both in microstructure, geochemical and geophysical parameters. The sandy facies 1 is located between these two end members. Homogeneous claystone, free of sandy or carbonaceous layers, occurs in the lower part of the investigated profile (shaly facies 1). This facies is characterized by a very small grain size of the clayey matrix, which can no longer be resolved by optical microscopy. Larger components (> 10 µm) frequently occurring in the matrix include iron sulfides (pyrite), carbonate particles, fossil shells and quartz grains. The iron sulfides have presumably been formed (early) diagenetically under anoxic conditions. Throughout the section, we observed several steep or gradual variations in grain size, carbonate and/or clay mineral content. Increased detrital input in form of thin silty-sandy layers was observed in the shaly facies 2 in the upper part of the profile. Especially the carbonate-rich sandy facies and the sandy facies 1 show a higher proportion of silty-sandy layers alternating with clay-rich intervals. Sedimentary structures can include pyritized burrows, continuous or thinning-out sand layers or larger biogenic carbonate fragments. Chaotic or disrupted bedding might result from bioturbation or early sedimentary landslides (slumping). Coarser beds that thin out are associated with storm events (Wetzel and Allia 2003), pointing to deposition close to the storm-wave base (Lauper et al. 2018 and references therein). The observed carbonate cementation of the silty-sandy layers is dominant in the thicker beds of sandy facies 1, but does not occur consistently in the shaly facies 2. This applies in particular to bioturbated structures and to thin sand layers.
Geochemistry and mineralogical rock composition
The obtained mineralogical and geochemical data largely support the petrographic–structural studies of this work and the observations made in Galletti and Jaeggi (2019). Generally, SiO2, Al2O3, Fe2O3 and a high CEC (as a measure of retention capacity) correlate with a high amount of clay minerals. In the clay-rich samples, elevated iron content can be attributed to the presence of pyritized burrows and finely disseminated framboidal aggregates of pyrite. On the other hand, CaO, MnO and Zr correlate with carbonate-rich or detrital-grain-rich sand layers. For both shaly facies types, the MgO content is bound to the clay-rich matrix of the Opalinus Clay (Kneuker et al. 2017). Zr is interpreted as an indicator for the presence of detrital grains. This corresponds well to a steady increase in Zr towards the sandy facies type, showing the highest amount of detrital input, documented by quartz-rich, silty-sandy layers. The decrease in CEC in the carbonate-rich sandy facies can be attributed to a decreasing content of swellable clay minerals (e.g. Frederickx et al. 2018) and correlates well with a decreasing Al2O3. This might have an impact on radionuclide retention capacity and swelling capacity, the latter especially important for resealing of natural fault planes and artificial fractures. The cores gave opportunity to study both important transitions from the shaly facies 1 towards the carbonate-rich sandy facies (sharp transition zone 1) and the more gradual and previously seldom sampled transition from the carbonate-rich sandy facies towards the sandy facies 1 (transition zone 2). Mineralogical and geochemical investigations revealed a modified composition of carbonates (including extensive cementation) in these intervals. In addition to omnipresent calcite, diagenetic pyrite nodules and siderite, ankerite and kutnohorite were observed in transition zone 1. In transition zone 2 enrichments of Mg-rich ankerite and kutnohorite were found in addition to calcite. This was confirmed by the geochemical data, indicating enrichments of Fe2O3 and MnO in transition zone 1 and of MgO and MnO in transition zone 2 (Fig. 7).
Variations in geochemical composition can be further visualized using a ternary diagram according to Brumsack (1989), that is based on the three main components CaO (proxy for carbonate), SiO2 (proxy for quartz) and Al2O3 (proxy for alumosilicates like clay minerals) (Fig. 10). The results presented in the preceding sections and in Fig. 10 confirm that the shaly facies 2 and a few samples from the carbonate-rich sandy facies are compositionally closely related to the most homogenous facies type of the Opalinus Clay, the shaly facies 1. In contrast, the sandy facies 1 and the carbonate-rich sandy facies represent the more heterogeneous endmembers (including a high lithological variability with distinct variations in element distribution and CEC) with probably altered material and/or barrier properties, when compared with the well characterized shaly facies 1. This is also reflected by the structural studies, which revealed an intercalation of carbonaceous-sandy layers and clay-rich parts alternating on the cm to dm scale (compare to Fig. 5). The shaly facies 1 represents the most homogenous area in terms of composition, as compared to the carbonate-rich and sandy facies types.
The new results are consistent with previously published data and support the classification of the Opalinus Clay at the Mont Terri site into major facies types and further into subfacies types (see Sect. Intra-facies variability in the Opalinus Clay).
Intra-facies variability in the Opalinus Clay
The description of the geological subunits (facies types) in claystone has been extended with the introduction of the subfacies types, allowing a fine-resolution characterization within each facies type. Individual subfacies types are characterized by distinctive colors, grain size, degree of bioturbation, sedimentary structure and mineralogical composition (Lazar et al. 2015). For the present study, we successfully applied the classification of subfacies types according to Lauper et al. (2018) and introduced a new subfacies type (Fig. 4). This was necessary to capture the composition of the shaly facies 2, not included in the study of Lauper et al. (2018). The subfacies concept is well suited to capture the structural and compositional intra-facies variability of the investigated drill cores and is additionally confirmed by the good correlation with geochemical analyses and ERT data (Fig. 2).
The present study, together with the investigations of Lauper et al. (2018), reveal a rather high intra-facies heterogeneity, especially for the carbonate-rich sandy facies and the sandy facies type 1. In contrast, the shaly facies 1 is the most homogenous facies type of the investigated claystone sequence. Here, in accordance with Lauper et al. (2018), only one subfacies type (SF1) and few diagenetic carbonate interlayers showing cone-in-cone fabric were observed.
Not surprisingly, the trends in major element composition (Sect. Geochemistry and mineralogical rock composition) are reflected by the results when broken down into the six subfacies types (Fig. 10). The subfacies type SF1 and the newly defined subfacies type SF2a are dominated by clay minerals and quartz. The subfacies type SF2 and especially SF3 show a higher Si/Al ratio, the subfacies types SF4 and SF5 are characterized by increased carbonate content, all consistent with the petrographic observations. The composition of the “average shale” according to Wedephol (1971) is located close to the argillaceous–siliceous claystones of the subfacies type SF2. The trends in geochemical distribution of distinct elements independently confirm the (micro)structurally based assignment of the samples to a certain subfacies type, which was demonstrated as well by Lauper et al. (2018). A summary of the structural–compositional characteristics including trends in resistivity within the individual subfacies types of Opalinus Clay can be found in Fig. 4.
The established subfacies model is valid for the rock laboratory scale. The subfacies types applied in the present study should be regarded as a preliminary classification of the Opalinus Clay at the Mont Terri site. For transition to other localities, they need to be confirmed and/or modified in future studies (cf. Lauper et al. 2020).
Lateral structural–compositional variability
Lateral layer variations (parallel to bedding) reflect the spatial distribution of depositional conditions with regard to the sedimentation area. First statements on lateral variability can be made based on drill core investigations of thin carbonate-rich or silty-sand layers. As our observations have shown, some of these thin features are not continuous, as they are not exceeding the core diameter. However, a comparison with data from neighboring boreholes indicates that the majority of the larger (subfacies) scale structures is laterally traceable; this is true especially for the sandy facies 1 (Figs. 2 and 9). With few exceptions, almost the same structures were detected in the geological and geophysical datasets from different boreholes (Fig. 9). The correlation is less clear for the carbonate-rich sandy facies, in this case not every peak overlaps in the ERT curves pointing to an increased lateral intra-facies variability (in addition to the high vertical variability).
In addition, the data suggest that not all sand layers of the sandy facies thin out laterally after a few cm or dm, and; thus, there is a stronger lateral continuity than previously assumed, at least for the thicker layers > 15 cm (cf. Jaeggi et al. 2014). The good lateral continuity of the transition zone 1 (at the base of the carbonate-rich sandy facies) is indeed well known, as these carbonate-rich beds are used as stratigraphic marker horizons throughout the Mont Terri rock laboratory (e.g. Galletti and Jaeggi 2019). This also includes a nodulous pyrite layer at the base of transition zone 1 (compare to Hostettler et al. 2017; Jaeggi et al. 2020). Based on the results of the present study, we can confirm the rather low lateral variability inside the sandy facies 1 and the increased intra-facies variability within the carbonate-rich sandy facies, for the latter on both vertical and lateral scale. This is not the case for the diagenetic carbonate beds showing cone-in-cone fabric in the homogenous shaly facies 1, as they cannot be correlated between BAD-2 and BWS-I2 (Fig. 2). A mapping of underground galleries or outcrops, if applicable, can provide more detailed information on lateral continuity as compared to a correlation based on the borehole investigations (compare to Müller and Jaeggi 2012; Jaeggi et al. 2020). Despite this, the correlation of both important transition zones (facies boundaries of the carbonate-rich sandy facies) is perfectly possible using the set of methods applied in the present study.
The applied facies and subfacies model is valid for the rock laboratory scale, as the lithology of the Opalinus Clay varies laterally on a regional scale. The carbonate-rich sandy facies is typical for the Jura region in western Switzerland; it does not occur in the proposed siting regions for a deep geological repository in Northern Switzerland. This might be explained with the proximity of the Burgundy High to the west (Lauper et al. 2020) and with differential subsidence resulting in an increased W–E variability of the Opalinus Clay in Switzerland (Lauper et al. 2018 and references therein).
Correlation of geophysical data with rock fabrics
Previous investigations have shown that variations in geoelectrical measurements on Opalinus Clay can be attributed either to structures related to natural faults, artificial fractures or to small-scale sedimentary heterogeneities in the drill core profile (e.g. Kneuker et al. 2017; Schuster et al. 2017, 2019).
Electrical resistivity can depend upon a multitude of factors, including lithology, porosity, connectivity of pores, nature of the pore fluids and the presence of ore minerals in the rock matrix (Telford et al. 1990). In the investigated claystones, the varying ERT signal can be attributed to the differences in clay mineral content. Due to the large specific internal surface of clay minerals and the associated interface conductivity, clay-rich intervals with an elevated saturation show a high conductivity and correspondingly a low resistivity of < 10 Ωm. Other factors like porosity and the water saturation are in turn dependent on the clay mineral content (Archie 1950).
The ERT profiles suggest that both the shaly facies 1 and 2 (including subfacies types SF1, SF2a and SF2) are characterized by resistivity < 10 Ωm with little variation (Fig. 2). In contrast, thicker limestones or carbonate layers, especially when well cemented, are characterized by a resistivity > 40 Ωm (Telford et al. 1990; Keller and Frischknecht 1996). These intervals correspond to the subfacies types SF4 and SF5. This is also the case for the two lithofacies transitions towards the carbonate-rich sandy facies, which stand out as high-resistivity zones (> 40 Ωm) in the geoelectrical profiles. These intervals are characterized by increased cementation; in addition mineralogical and structural investigations revealed a modified composition of diagenetic carbonates (Fe-rich ankerite and Mn-rich kutnohorite) in these intervals (see Sect. Mineralogical-geochemical rock composition). However, we do not expect that this compositional difference had a direct influence on the ERT signal for the investigated profiles (compare to Verwer et al. 2011 and Regnet et al. 2019). The high-resistivity values might be related to the increased level of diagenetic carbonate cementation and the correspondingly low clay mineral content (resulting in a low interface conductivity, low porosity and a decreased water content).
The mean resistivity in the sandy facies (4.70 m to 19.40 m) is significantly higher (ca. 15 Ωm); here the heterogeneity in form of calcareous–siliceous layers (SF3 and SF4) is considerably stronger (Fig. 9). The average level of resistivity in the carbonate-rich sandy facies ranges between the values of the shaly and the sandy facies types. This decrease (in comparison to the sandy facies) was also reported by Schuster et al. (2017) and might be explained by the presence of clay-rich interlayers (SF2), which are common in the carbonate-rich sandy facies. They are the reason for the increased lithological heterogeneity in the latter, also reflected by the high variation of amplitudes in resistivity data, resulting in a more pronounced contrast to carbonate-rich, high-resistivity layers and their better visibility in the ERT data in comparison to the sandy facies 1. This illustrates that both the composition of the subfacies type and the overall composition of the facies type have to be taken into account. A comparison with the adjacent borehole BGC-2 and BWS-I2 illustrates the good reproducibility of the geoelectric data (Fig. 9). Overall, the resistivity values obtained for the sandy and carbonate-rich sandy facies are close to published values derived for the Mont Terri rock laboratory (e.g. Schuster et al. 2017).
Fractures of the excavation damaged zone (EDZ) in the unsaturated parts around the underground galleries are generally well visible and characterized by a high resistivity > 20 Ωm (e.g. Kneuker et al. 2017). However, this is not the case for the ERT data from the BAD-2 borehole. This speaks against a very pronounced unsaturated zone in BAD-2, although typical EDZ fracture patterns were observed down to 1.5 m drill core depth. Fractures and faults in the deeper part of a drill core, where the rock is saturated, are visible in ERT profiles only as moderately elevated or even low resistivity as in the case of the Main Fault (Kneuker et al. 2017). The increased lithological variability in the sandy or carbonate-rich sandy facies types probably complicated the detection of fault structures within the ERT signal. Nevertheless, the structural studies of the BAD-2 drill core confirmed that faults are rare in both the sandy and the carbonate-rich sandy facies, larger fault zones including scaly clay are lacking.
The geophysical measurements provide robust results regarding the detection and in situ characterization of structural and sedimentary heterogeneities in claystone. To distinguish between fractured/faulted domains and variations in the mineralogical composition, a correlation with ultrasonic interval velocity measurements or other geophysical logs would be helpful (e.g. Kneuker et al. 2017; Schuster et al. 2017, 2019). Unfortunately, this type of measurements was not performed in the BAD-2 borehole.
Fault occurrence and heterogeneities
Claystone formations are composed of clay-rich intervals, silty-sandy or carbonate-rich intercalations and therefore include a variety of mechanically distinct intervals and boundaries (Klinkenberg et al. 2009; Gale et al. 2014; An et al. 2020). Claystone formations with high clay content tend to have lower strength with regard to shear and tensile failure (Sone and Zoback 2011) and generally show reduced frictional resistance by bed-parallel sliding (Orellana et al. 2018a, b). Isolated quartz or carbonate grains in claystone are likely to have less of an effect on strength than constituents in contact (silty-sandy layers, quartz or carbonate cements) (e.g. Kaufhold et al. 2013; Gale et al. 2014; Zhang and Laurich 2020). Owing to its tectonic history (e.g. Nussbaum et al. 2011, 2017 and references therein), the Opalinus Clay at Mont Terri is affected by several individual faults and fault zones.
In the analyzed core material, deformation was accommodated mainly by frictional sliding, documented in the formation of microshears and slickensides (e.g. Engelder et al. 1975; Laurich et al. 2014; Kneuker et al. 2017), consistent with experimental results (Orellana et al. 2018a). Slickensided shear surfaces show differences in surface roughness/shininess, step length and step height. All investigated faults appear macroscopically closed, but can be reactivated or disintegrate under excess stress (e.g. during drilling) into cm-sized debris. It was found that most fault planes occur in the shaly facies types (Fig. 6). The observed fault density (around 0–9 m−1) is consistent with the data from Kneuker et al. (2017), who report a fault density of 1–8 m−1 outside the Main Fault in Mont Terri rock laboratory.
With increasing quartz content, an increased roughness of the fault surfaces was observed (Fig. 6). This waviness results from the different stiffness of components inside the rock material, e.g. early diagenetic nodules and silt-rich or carbonate lenses that formed during compaction of the sediments and thin clay sheets anastomosing around the larger grains and sand lenses. If the differential stress during shearing is not sufficient to activate fracturing of the rigid components, significant bedding parallel slip is hindered, implicating a rather small displacement along those types of faults. This is consistent with Kaufhold et al. (2013), who observed for samples from the sandy facies an increase in shear strength with increasing carbonate content. This is also consistent with experimental results from An et al. (2020), who found that phyllosilicate-poor shale gouges exhibited higher frictional strength as compared to phyllosilicate-rich gouges.
Palaeostress measurements in the Mont Terri rock laboratory by Nussbaum et al. (2011) revealed top to NW thrust movements with a shortening axis of 330°—150° (parallel to the strike line of S0) for the principal deformation phase. Our observation of dip-slip and reverse or thrust movements are therefore in good agreement with Nussbaum et al. (2011) and Laurich et al. (2014). This further indicates that the majority of observed faults are related the folding of the Jura fold belt as a consequence of the propagation of the Alpine foreland towards NNW, starting in the Middle Miocene (Becker 2000; Nussbaum et al. 2011). Veins as evidence for syntectonic palaeo-fluid transfer were detected exclusively in the shaly facies 1 of the BAD-2 cores, but they are known from the carbonate-rich sandy facies (window in gallery 98) or from other localities/facies types inside the Mont Terri rock laboratory (Pearson et al. 2003; Clauer et al. 2017; Mazurek and de Haller 2017; Jaeggi et al. 2020). The presence of veins document enhanced palaeo-permeability during fault activity, most probably at the time of folding of the Jura Mountains or during later fault reactivation.
With regard to subfacies types, most faults were observed in the clay-rich subfacies types SF1, SF2 and SF2a. Even for the sandy and carbonate-rich sandy facies, faults occur predominately in the clay-rich and silty subfacies types SF2 and SF3 (Fig. 2). This is consistent with Jaeggi et al. (2020) and Kneuker et al. (2017), who found that fault zones in the Opalinus Clay often correlate with an increased clay content; Kneuker et al. (2017) additionally confirmed a corresponding low electrical resistivity in ERT data. The prominent Main Fault is also located in the shaly facies 1 (subfacies type SF1; Laurich et al. 2014, Fig. 1), the facies type with the highest amount of clay minerals. In terms of fault orientation, the most dominant occurrence of faults within the shaly facies 1 is subparallel to bedding S0 (Nussbaum et al. 2011; Jaeggi et al. 2017), this represents also the orientation of the Main Fault structure. Most of these faults subparallel to S0 are either reactivated bedding planes or faults dipping 5°–10° steeper than S0 (Jaeggi et al. 2020). According to Lauper et al. (2018), the subfacies model may be used for an estimation of rock properties such as failure strength dependent on carbonate content. Kneuker et al. (2020) discovered that brittle fracturing could vary significantly with the presence of compositional heterogeneities on the dm to m scale in Lower Cretaceous claystones from Northern Germany. In the investigated cores from Opalinus Clay, small-scale faults indeed often accumulate next to heterogeneities, pointing to peak stresses along the transition zone towards carbonate-rich or sandy intervals (facies and/or subfacies type scale).
In the rather complex Main Fault, located in the shaly facies 1, repeated fault (re)activation led the formation of a very fine-grained, cohesionless fault gouge and to a fragmentation of the previously formed calcite veins (e.g. Laurich et al. 2014; Kneuker et al. 2017). Such features were not observed for the discrete brittle fault planes in the BAD-2 drill cores. Nevertheless, the high fault density continuing beyond 1.5 m borehole depth, thereby exceeding the EDZ, indicates that the artificial fracture system of the EDZ intermingled with natural fault planes present in the BAD-2 cores. For this zone, a local reactivation of shear planes during the excavation of the underground galleries, as reported in Nussbaum et al. (2011) and Thöny (2014) cannot be ruled out.
Implications of the geological–geophysical investigations and their results
Depending on their depositional history, claystone formations are characterized by a large number of small-scale facies changes and corresponding lithological transitions (e.g. Gale et al. 2014). Petrographic–structural studies together with geophysical borehole measurements form the basis for rock characterization and provide first indications for the compositional–structural variability. For the present study, the geological description has been extended with the introduction of the subfacies concept, allowing a high-resolution characterization of the claystone formation in question (Lazar et al. 2015; Lauper et al. 2018). A high lithological intra-facies variability subperpendicular to bedding is widespread, especially for the silt-rich, sandy and carbonate-rich parts of the investigated claystone sequences. These heterogeneities on the subfacies scale could have an impact on the barrier properties (e.g. mechanical behavior, retention capacity, behavior under thermal load). Of particular interest is the observed decrease in cation exchange capacity inside the carbonate-rich or sandy interlayers (e.g. Frederickx et al. 2018). This could have an impact on radionuclide retention and swelling capacity, the latter especially important for the resealing of natural fault planes and artificial fractures.
Deformation of the investigated claystones occurred localized along discrete brittle fault planes; the facies type can influence the fracture behavior and the characteristics of natural fault planes. It was found that most faults occur in the clay-rich facies types and intervals. This probably reflects the low shear strength of the investigated clay-rich sections which can be attributed to the anisotropy of the mechanical properties (Gautschi 2017), favoring the development of fault planes aligned subparallel to bedding (Orellana et al. 2018a; b). Brittle fault planes and lithological heterogeneities represent planes of mechanical weakness (Marschall et al. 2017), which are prone for reactivation (e.g. Orellana et al. 2018b). It was shown experimentally that increasing shear strain can lead to dilatancy and to a fault parallel permeability enhancement (Samuelson et al. 2009; Orellana et al. 2019) in agreement with in situ field observations (Guglielmi et al. 2017; Jeanne et al. 2018). The detection and detailed characterization of compositional–structural heterogeneities is therefore of particular importance for the evaluation of potential host rock formations. Their impact on barrier properties is an important subject and needs to be adequately investigated and considered in any long-term safety analysis.
Conclusions
The following conclusions can be drawn from the multidisciplinary investigations presented above.
-
A high lithological intra-facies variability subperpendicular to bedding is widespread, especially for the sandy and carbonate-rich parts of the investigated claystone sequence.
-
On the other hand, the data indicate a rather low lateral variability (parallel to bedding), except for the carbonate-rich sandy facies. Here, an increased compositional–structural variability for both the vertical and lateral scale was observed.
-
The observed intra-facies variability in the structural, geochemical and geophysical dataset is compatible with the new classification scheme of geological subunits proposed by Lauper et al. (2018).
-
Varying resistivity in high-resolution ERT measurements can be attributed to differences in clay mineral and carbonate content. Especially the transition zones and facies boundaries can be precisely localized, the reproducibility of the measurements and observations was confirmed by a comparison with boreholes drilled in parallel.
-
Structural heterogeneities include fault planes, deformation in the investigated claystones is localized along brittle faults. The facies type can influence the fracture behavior and the fabric of natural fault planes. It especially has an influence on the abundance of fractures.
-
Both structural and compositional heterogeneities on the subfacies scale could have an impact on barrier properties (e.g. mechanical behavior, radionuclide retention capacity, swelling capacity, behavior under thermal load). Their detection is of particular importance for the evaluation of potential host rock formations.
Availability of data and material
The manuscript has data included as electronic supplementary material.
References
An M, Zhang F, Elsworth D, Xu Z, Chen Z, Zhang L (2020) Friction of longmaxi shale gouges and implications for seismicity during hydraulic fracturing. J Geophys Res Solid Earth. https://doi.org/10.1029/2020JB019885
Archie GE (1950) Introduction to petrophysics of reservoir rocks. AAPG Bull 34:943–961
Becker A (2000) The Jura Mountains – an active foreland fold-and-thrust belt? Tectonophysics 321:381–406
Bläsi HR, Moeri A, Bossart P (1996) Results of the phase 1 drilling campaign. Technical Report TR 96–01, Federal Office of Topography (swisstopo), Wabern, Switzerland
Boles A, van der Pluijm B, Mulch A, Mutlu H, Uysal IT, Warr LN (2015) Hydrogen and 40Ar/39Ar isotope evidence for multiple and protracted paleofluid flow events within the long-lived North Anatolian Keirogen (Turkey). Geochem Geophys Geosyst 16:1975–1987
Bossart P, Thury M (2008) Mont terri rock laboratory project, programme 1996 to 2007 and results. Rep Swiss Geol Surv 3:1–445
Bossart P, Bernier F, Birkholzer J, Bruggeman C, Connolly P, Dewonck S, Fukaya M, Herfort M, Jensen M, Matray JM, Mayor JC, Moeri A, Oyama T, Schuster K, Shigeta N, Vietor T, Wieczorek K (2017) Mont Terri rock laboratory, 20 years of research: introduction, site characteristics and overview of experiments. Swiss J Geosci 110:3–22
Brumsack HJ (1989) Geochemistry of recent TOC-rich sediments from the Gulf of California and the Black Sea. Geol Runds 78:851–882
Crisci E, Ferrari A, Giger SB, Laloui L (2019) Hydro-mechanical behaviour of shallow Opalinus Clay shale. Eng Geol 251:214–227
Clauer N, Techer I, Nussbaum C, Laurich B (2017) Geochemical signature of paleofluids in microstructures from main fault in the Opalinus Clay of the Mont Terri rock laboratory, Switzerland. Swiss J Geosci 110:105–128
Dohrmann R, Genske D, Karnland O, Kaufhold S, Kiviranta L, Olsson S, Plötze M, Sandén T, Sellin P, Svensson D, Valter M (2012) Interlaboratory CEC and exchangeable cation study of bentonite buffer materials: I. Cu(II)-triethylentetramine method. Clay Clay Miner 60:162–175
Engelder JT, Logan JM, Handin J (1975) The sliding characteristics of sandstone on quartz fault-gouge. Pure Appl Geophys 113:68–86
Frederickx L, Honty M, De Craen M, Dohrmann R, Elsen J (2018) Impact of mineralogy and pore water chemistry on the CEC of the boom clay formation (Belgium). Clay Clay Miner 66:449–465
Gale JF, Laubach SE, Olson JE, Eichhubl P, Fall A (2014) Natural fractures in shale: a review and new observations. AAPG Bull 98:2165–2216
Galletti M, Jaeggi D (2019) AD experiment: Drillcore documentation of boreholes BAD-1 and BAD-2. Technical Note TN 2019–06, Federal Office of Topography (swisstopo), Wabern, Switzerland
Gautschi A (2017) Safety-relevant hydrogeological properties of the claystone barrier of a Swiss radioactive waste repository: An evaluation using multiple lines of evidence. Grundwasser 22:221–233
Guglielmi Y, Birkholzer J, Rutqvist J, Jeanne P, Nussbaum C (2017) Can fault leakage occur before or without reactivation? Results from an in situ fault reactivation experiment at Mont Terri. Energy Procedia 114:3167–3174
Günther T, Rücker C, Spitzer K (2006) Three-dimensional modelling and inversion of DC resistivity data incorporating topography—II Inversion. Geophys J Int 166:506–517
Hostettler B, Reisdorf AG, Jaeggi D, Deplazes G, Bläsi H, Morard A, Feist-Burkhard S, Waltschew A, Dietze V, Menkveld-Gfeller U (2017) Litho-and biostratigraphy of the Opalinus Clay and bounding formations in the Mont Terri rock laboratory (Switzerland). Swiss J Geosci 110:23–37
Jaeggi D, Bossart P, Wymann L (2014) Kompilation der lithologischen Variabilität und Eigenschaften des Opalinus-Ton im Felslabor Mont Terri. Expertenbericht im Rahmen der Beurteilung des Vorschlags von mindestens zwei geologischen Standortgebieten pro Lagertyp, Etappe 2, Sachplan geologische Tiefenlager. Federal Office of Topography (swisstopo), Wabern, Switzerland
Jaeggi D, Laurich B, Nussbaum C, Schuster K, Connolly P (2017) Tectonic structure of the “main fault” in the Opalinus Clay, Mont Terri rock laboratory (Switzerland). Swiss J Geosci 110:67–84
Jaeggi D, Galletti M, Amacher F, Dunst R, Nussbaum C, Raselli R, Ringeisen M, Schefer S, Bossart P (2020) Gallery 2018: Excavation and geological documentation. Technical Report TR2018–04, Federal Office of Topography (swisstopo), Wabern, Switzerland
Jeanne P, Guglielmi Y, Rutqvist J, Nussbaum C, Birkholzer J (2018) Permeability variations associated with fault reactivation in a claystone formation investigated by field experiments and numerical simulations. J Geophys Res Solid Earth 123:1694–1710
Kaufhold A, Gräsle W, Plischke I, Dohrmann R, Siegesmund S (2013) Influence of carbonate content and micro fabrics on the failure strength of the sandy facies of the Opalinus Clay from Mont Terri (Underground Rock Laboratory). Eng Geol 156:111–118
Keller GV, Frischknecht FC (1996) Electrical Methods in Geographical Prospecting. Pergamon Press, London
Klinkenberg M, Kaufhold S, Dohrmann R, Siegesmund S (2009) Influence of carbonate microfabrics on the failure strength of claystones. Eng Geol 107:42–54
Kneuker T, Hammer J, Shao H, Schuster K, Furche M, Zulauf G (2017) Microstructure and composition of brittle faults in claystones of the Mont Terri rock laboratory (Switzerland): New data from petrographic studies, geophysical borehole logging and permeability tests. Eng Geol 231:139–156
Kneuker T, Blumenberg M, Strauss H, Dohrmann R, Hammer J, Zulauf G (2020) Structure, kinematics and composition of fluid-controlled brittle faults and veins in Lower Cretaceous claystones (Lower Saxony Basin, Northern Germany): Constraints from petrographic studies, microfabrics, stable isotopes and biomarker analyses. Chem Geol 540:119501
Kolditz O, Frühwirth T, Görke UJ, Helbig C, Konietzky H, Maßmann J, Nest M, Rink K, Sattari A, Schmidt P, Pötschke D, Rink K, Steeb H, Wuttke F, Yoshioka K, Vowinckel B, Ziefle G, Nagel T (2021) GeomInt - Geomechanical integrity of host and barrier rocks - experiment, modeling and analysis of discontinuities. Environ Earth Sci, under review
Lauper B, Jaeggi D, Deplazes G, Foubert A (2018) Multi-proxy facies analysis of the Opalinus Clay and depositional implications (Mont Terri rock laboratory, Switzerland). Swiss J Geosci 111:383–398
Lauper B, Deplazes G, Vogel H, Jaeggi D, Wohlwend S, Ariztegui D, Foubert A (2020) Geochemical fingerprinting of key lithologies and depositional processes across the upper boundary of the Opalinus Clay (Aalenian, Middle Jurassic, northern Switzerland). Depos Rec. https://doi.org/10.1002/dep2.126
Laurich B, Urai JL, Desbois G, Vollmer C, Nussbaum C (2014) Microstructural evolution of an incipient fault zone in Opalinus Clay: insights from an optical and electron microscopic study of ion-beam polished samples from the Main Fault in the Mt-Terri Underground Research Laboratory. J Struct Geol 67:107–128
Lazar OR, Bohacs KM, Macquaker JH, Schieber J, Demko TM (2015) Capturing key attributes of fine-grained sedimentary rocks in outcrops, cores, and thin sections: nomenclature and description guidelines. J Sediment Res 85:230–246
Marschall P, Giger S, De La Vassière R, Shao H, Leung H, Nussbaum C, Trick T, Lanyon B, Senger R, Lisjak A, Alcolea A (2017) Hydro-mechanical evolution of the EDZ as transport path for radionuclides and gas: insights from the Mont Terri rock laboratory (Switzerland). Swiss J Geosci 110:173–194
Mazurek M, Hurford AJ, Leu W (2006) Unravelling the multi-stage burial history of the Swiss Molasse Basin: integration of apatite fission track, vitrinite reflectance and biomarker isomerisation analysis. Basin Res 18:27–50
Mazurek M, de Haller A (2017) Pore-water evolution and solute-transport mechanisms in Opalinus Clay at Mont Terri and Mont Russelin (Canton Jura, Switzerland). Swiss J Geosci 110:129–149
Meier LP, Kahr G (1999) Determination of the cation exchange capacity (CEC) of clay minerals using the complexes of Copper (II) ion with Triethylenetetramine and Tretraethylenepentamine. Clay Clay Miner 47:386–388
Minardi A, Crisci E, Ferrari A, Laloui L (2016) Anisotropic volumetric behaviour of Opalinus clay shale upon suction variation. Géotech Let 6:144–148
Müller P, Jaeggi D (2012) SO experiment: Sedimentary structure in the sandy facies of the Opalinus Clay at Mont Terri rock laboratory. Technical Note TN 2012–45, Federal Office of Topography (swisstopo), Wabern, Switzerland
Nesbitt BE, Muehlenbachs K (1989) Origins and movement of fluids during deformation and metamorphism in the Canadian Cordillera. Science 245:733–736
Nussbaum C, Bossart P, Amann F, Aubourg C (2011) Analysis of tectonic structures and excavation induced fractures in the Opalinus Clay, Mont Terri underground rock laboratory (Switzerland). Swiss J Geosci 104:187–210
Nussbaum C, Kloppenburg A, Caër T, Bossart P (2017) Tectonic evolution around the Mont Terri rock laboratory, northwestern Swiss Jura: constraints from kinematic forward modelling. Swiss J Geosci 110:39–66
Orellana LF, Scuderi MM, Collettini C, Violay M (2018a) Do scaly clays control seismicity on faulted shale rocks? Earth Planet Sci Lett 488:59–67
Orellana LF, Scuderi MM, Collettini C, Violay M (2018b) Frictional properties of Opalinus Clay: Implications for nuclear waste storage. J Geophys Res Solid Earth 123:157–175
Orellana LF, Giorgetti C, Violay M (2019) Contrasting mechanical and hydraulic properties of wet and dry fault zones in a proposed shale-hosted nuclear waste repository. Geophys Res Lett 46:1357–1366
Pearson FJ, Arcos D, Bath A, Boisson JY, Fernández AM, Gäbler HE, Gaucher E, Gautschi A, Griffault L, Hernán P, Waber HN (2003) Mont Terri Project - Geochemistry of Water in the Opalinus Clay Formation at the Mont Terri Rock Laboratory. Geology Series 5 Federal Office for Water and Geology (FOWG), Bern, Switzerland
Regnet JB, David C, Robion P, Menéndez B (2019) Microstructures and physical properties in carbonate rocks: a comprehensive review. Mar Pet Geol 103:366–376
Reimann C, Birke M, Demetriades A, Filzmoser P, O'Connor P (2014) Chemistry of Europe's agricultural soils, part A. In: Methodology and Interpretation of the GEMAS Data Set. Geol Jb 102:21–523
Reisdorf AG, Hostettler B, Jaeggi D, Deplazes G, Bläsi HR, Morard A, Feist-Burkhardt S, Waltschew A, Dietze V, Menkveld-Gfeller U (2016) Litho- and biostratigraphy of the 250 m-deep Mont Terri BDB-1 borehole through the Opalinus Clay and bounding formations, St-Ursanne, Switzerland. Technical Report TR 2016–02, Federal Office of Topography (swisstopo), Wabern, Switzerland
Rücker C, Günther T, Spitzer K (2006) Three-dimensional modelling and inversion of dc resistivity data incorporating topography: I. Modelling. Geophys J Int 166:495–505
Samuelson J, Elsworth D, Marone C (2009) Shear-induced dilatancy of fluid-saturated faults: Experiment and theory. J Geophys Res Solid Earth 114:B12404
Schuster K, Amann F, Yong S, Bossart P, Connolly P (2017) High-resolution miniseismic methods applied in the Mont Terri rock laboratory (Switzerland). Swiss J Geosci 110:213–231
Schuster K, Furche M, Shao H, Hesser J, Hertzsch JM, Gräsle W, Rebscher D (2019) Understanding the evolution of nuclear waste repositories by performing appropriate experiments selected investigations at Mont Terri rock laboratory. Adv Geosci 49:175–186
Sone H, Zoback MD (2011) Visco-plastic properties of shale gas reservoir rocks: ARMA 45th U.S. Rock Mechanics Symposium, San Francisco, California. ARMA-11–417
Telford W, Geldart LP, Sheri RE (1990) Applied Geophysics, 2nd edn. Cambridge University Press, Cambridge
Thöny R (2014) Geomechanical analysis of excavation-induced rock mass behavior of faulted opalinus clay at the mont terri underground rock laboratory (Switzerland). Dissertation, ETH Zurich
Ufer K, Kleeberg R, Bergmann J, Dohrmann R (2012) Rietveld refinement of disordered illite/smectite mixed layered minerals with a recursive algorithm. II: powder pattern refinement and quantitative phase analysis. Clay Clay Miner 60:535–552
Verwer K, Eberli GP, Weger RJ (2011) Effect of pore structure on electrical resistivity in carbonates. AAPG Bull 95:175–190
Wedepohl KH (1971) Environmental influences on the chemical composition of shales and clays. Phys Chem Earth 8:307–333
Wetzel A, Allia V (2003) Der Opalinuston in der Nordschweiz: Lithologie und Ablagerungsgeschichte. Eclogae Geol Helv 96:451–469
Zhang CL, Laurich B (2020) Mechanical behavior of sandy facies of Opalinus Clay under different load conditions. J Rock Mech Rock Eng 12:223–241
Zulauf G, Palm S, Petschick R, Spies O (1999) Element mobility and volumetric strain in brittle and brittle–viscous shear zones of the superdeep well KTB (Germany). Chem Geol 156:135–149
Acknowledgements
Many thanks go to the swisstopo team (C. Nussbaum, D. Jaeggi, T. Theurillat and S. Schefer) for local site support and onsite core documentation. Boreholes were drilled by S. Sanchez and C. Fixar, clay samples were prepared by T. Faust and A. Heiner; thanks to R. Dohrmann, F. Korte and K. Ufer (all BGR) for help with the interpretation of the mineralogical–geochemical dataset and/or sample handling. Several colleagues participated in the geophysical measurements (in alphabetical order): H. Albers, U. Nowak, F. Schulte and T. Tietz (all BGR). Their efforts are kindly acknowledged. We further would like to thank B. Lauper (University of Fribourg) for fruitful discussions regarding stratigraphy and the subfacies concept and J. Maßmann (BGR) for coordinating the AD experiment. We are grateful to D. Jaeggi (swisstopo) and G. Zulauf (Goethe University Frankfurt) for constructive comments on earlier versions of the manuscript. The authors would like to thank two anonymous reviewers for their helpful and constructive reviews, which helped to improve the quality of the present paper. The AD experiment received funding from the Federal Ministry for Education and Research (BMBF) under grant 03G0866A (GeomInt project). This study was supported by the German Federal Ministry for Economic Affairs and Energy (BMWi; 9Y2013020000).
Funding
Open Access funding enabled and organized by Projekt DEAL. The AD experiment received funding from the Federal Ministry for Education and Research (BMBF) under grant 03G0866A (GeomInt project). This study was supported by the German Federal Ministry for Economic Affairs and Energy (BMWi; 9Y2013020000).
Author information
Authors and Affiliations
Contributions
T.K. carried out sampling and the structural and mineralogical–geochemical investigations; M.F. performed the geophysical borehole measurements and the data processing. T.K. and M.F. contributed to the interdisciplinary interpretation of the presented results. T.K. took the lead in writing the manuscript, M.F. provided critical feedback; both authors shaped the manuscript substantially.
Corresponding author
Ethics declarations
Conflicts of interest
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
This article is a part of the Topical Collection in Environmental Earth Sciences on “Sustainable Utilization of Geosystems” guest edited by Ulf Hünken, Peter Dietrich and Olaf Kolditz.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Kneuker, T., Furche, M. Capturing the structural and compositional variability of Opalinus Clay: constraints from multidisciplinary investigations of Mont Terri drill cores (Switzerland). Environ Earth Sci 80, 421 (2021). https://doi.org/10.1007/s12665-021-09708-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12665-021-09708-1