Abstract
Topological defects in nematic liquid crystals are ubiquitous. The defects are important in understanding the fundamental properties of the systems, as well as in practical applications, such as colloidal self-assembly, optical vortex generation and templates for molecular self-assembly. Usually, spatially and temporally stable defects require geometrical frustration imposed by surfaces; otherwise, the system relaxes because of the high cost of the elastic energy. So far, multiple defects are kept in bulk nematic liquid crystals by top-down lithographic techniques. In this work, we stabilize a large number of umbilical defects by doping with an ionic impurity. This method does not require pre-patterned surfaces. We demonstrate that molecular reorientation controlled by an AC voltage induces periodic density modulation of ions accumulated at an electrically insulating polymer interface, resulting in self-organization of a two-dimensional square array of umbilical defects that is reconfigurable and tunable.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction
Control of the large-scale formation of functional micro and nano-patterns is attracting intense interest in the interdisciplinary field of materials science1. Self-organization in soft matter systems, such as colloids2,3, block copolymers4,5 and liquid crystals6,7, is widely used for designing materials with emergent properties and for templating structures with new functionalities. Recently, fabrication of periodic patterns focuses on the integration of top-down (lithographic) and bottom-up methods because structures prepared solely by self-organization often lack sufficient long-range order, which is crucial for practical use.
Nematic liquid crystals (NLCs) are anisotropic fluids that already possess long-range orientational order of the long axes of constituent molecules, with the preferred direction called the director (n). An advantage of NLCs is that the director can be easily controlled by external electric fields owing to its dielectric anisotropy, as in current LC display applications. Generally, inhomogeneous director structures, including topological defects, have high elastic energy costs and they appear as uncontrollable and unstable features in the bulk8,9 unless geometrically frustrated by a surface10,11 as seen in droplets12,13 and around colloids14,15,16. Although there are some experimental systems that exhibit spontaneous periodic patterns under electric and magnetic external fields17,18,19,20,21,22, during heating23 and in submicron thin films24,25, these observations are mostly limited to one-dimensional stripes. Two-dimensional patterns17,19,23,25,26 are relatively rare and are not formed over a large uniform area as reconfigurable, tunable patterns. Therefore, the stabilization of the complex director fields in NLCs is achieved by top-down lithographic approaches such as AFM scratch methods27,28, nanoimprint lithography29 and photo alignment30,31,32,33,34 for multi-stable alignments29,35, light diffraction gratings30 and optical vortex applications33,36,37,38,39. However, the templates used in these lithographic techniques limit the reconfigurability and controllability of the system, and spontaneous self-organization is important for further exploitation of NLCs.
In this work, we demonstrate stable arrays of defects in NLCs without preparing a pre-patterned mask. Our approach is based on the spontaneous self-organization of NLCs through the standard reorientation of the director supported by an AC voltage, V. For homeotropically aligned NLCs with negative dielectric anisotropy, the director tends to orient perpendicular to the applied field above a threshold voltage, V≥Vth. When the director tilt is induced toward the cell (horizontal) plane, degeneracy remains in the azimuthal angle, ϕ(x,y), which results in the formation of a topological defect in the xy-plane, and ϕ(x,y)=sϕ+c holds. Here, s=±1 and c is a constant value. These topological configurations are often referred to as umbilics40,41. Contrary to conventional coarsening behaviour42,43, we show that doping with a small amount of an ionic compound leads to the formation and stabilization of a large number of umbilics in a square arrangement without annihilation. The size of the grid is tunable from several hundreds of micrometres to several micrometres, producing a high-density of defects. A large single domain is obtained spontaneously by the edge effect of the electrodes. Moreover, optical manipulation enlarges the uniform area to the millimetre scale. The arrangement of umbilics can be regarded as a soft two-dimensional crystal on the micrometre scale, which enables the direct observation of the moving dislocations in non-uniform arrangements of umbilics.
Results
State diagram of the micrographic appearance
We begin by describing the observable textures. Sandwich cells, consisting of two parallel glass plates coated with indium-tin-oxide (ITO), are filled with NLCs (CCN-mn; trans,trans-4,4′-dialkyl-(1α,1′α-bicyclohexyl-4β-carbonitriles) (Fig. 1a). The ITO glass is spin-coated with an amorphous fluorinated polymer, CYTOP (CTX-809A, Asahi Glass Co.), dissolved in a fluorinated solvent (CT-Solv.180, Asahi Glass Co.) to induce the homeotropic anchoring44,45. An AC voltage of V=V0 cos2πft is applied to the ITO electrodes in order to induce the reorientation of n (Fig. 1b,c). The micrographic appearance is studied as a function of frequency f and amplitude V0. Figure 2a shows four typical textures of an NLC, CCN-37, doped with an ionic compound, 1 wt% tetrabutyl anmonium benzoate (TBABE), taken under crossed polarizers. Figure 2b shows the state diagram plotted on the f-V0 plane based on the observations of the 3.0-μm-thick cell. The details of the director configuration are addressed later (Fig. 4). At high-frequency, the well-known umbilical texture (U), consisting of randomly located ±1 umbilics, is observed. By decreasing the frequency gradually, a striped pattern (S) is formed from the U state. Further decrease of the frequency induces orthogonal strips, leading to a formation of a grid texture (G). Finally the dark texture of the homeotropic alignment (H) is observed in the low-frequency region. We stress that the emergence of these four states is qualitatively identical in the other cells with different cell thickness. As shown in Fig. 2b, although the present system is based on the standard Fréedericksz transition, all the boundaries of the transitional voltages separating adjacent states increase sharply as the frequency decreases. Considering that the theoretical threshold voltage of (ref. 46), where K3 is the elastic constant of the bend deformation, is several volts using typical parameters47, the observed Vth curve in Fig. 2b is markedly different.
Behaviour of threshold voltages
We examine the behaviour of Vth, which denotes the transitional voltage between the non-perturbed H alignment and the electric-field-induced G, S or U states, for several sample cells with various conditions. Typical results are summarized in Fig. 3a. Open symbols denote S and G states obtained by adjusting V0 and f, whereas closed symbols show the U state above Vth. In our standard experiments, a solution containing 3 wt% CYTOP is used for spin-coating unless otherwise mentioned. The thickness of the alignment layer ls is ∼120 nm, as estimated by spectroscopic ellipsometry. In this condition, Vth for the pure CCN-37 (used as received) is almost constant and small (magenta closed circles in Fig. 3a) due to the normal Fréedericksz transition. However, the ion-doped samples (open symbols in Fig. 3a) show a significant increase of Vth at low frequencies at any cell thickness d, while a good agreement is seen for all the data at high-frequencies. These observations confirm that the sharp increase of Vth is caused by the ionic contribution. To obtain more evidence, the thickness dependence of the CYTOP layer is examined, which leads to an important result explaining the Vth behaviour on ls. We dilute the CYTOP solution, for example, to 1.0 wt% (blue closed circles) so that the alignment layer becomes thinner (ls∼17 nm) under the same spin-coating conditions, which also initially induce the uniform H state. In spite of the same ionic concentration and the same interface, Vth substantially decreases compared with the data with open symbols and no further periodic G or S state pattern is formed. Moreover, the data for 0.8 wt% CYTOP solution (ls∼10 nm, black closed circles in Fig. 3a) agree with those for the pure CCN-37 except for very low-frequency region. These decreases in Vth indicate that a significant voltage drop occurs in the CYTOP layers due to the high resistivity which is larger than 1015 Ω· m (ref. 48) (http://www.agc.com/kagaku/shinsei/cytop/en/data.html), and the effective voltage on the NLC layer is essentially similar to all the cases. To support the finding, we also perform experiments using a surfactant monolayer of a silane-coupling agent, N,N-dimethyl-N-octadecyl-3-aminopropyltrimethoxysilyl chloride (DMOAP, Aldrich) and a polyimide layer (SE-1211, Nissan Chemical), which are well-known homeotropic surfaces. For SE-1211, effects of the spin-coating conditions are also examined, as described in the Experimental section. The behaviour of these homeotropic surfaces is similar to that of the pure NLC sample (magenta closed circles in Fig. 3a), which shows no substantial change in Vth. Furthermore, neither the G nor S textures appear. These results also prove that the increase of Vth is responsible for the pattern formation caused by electrical insulation, that is, the field-screening effect of the ionic localization in the vicinity of the CYTOP layer (Fig. 3b). Thus, the underlying physical origin of Vth curves is the Fréedericksz transition even though the variation of Vth depends on the thickness of the CYTOP layer, ls. In other words, the bulk reorientation by the dielectric property is essential in this phenomenon. We note that polarization microscopy also excludes the possibility of the director reorientation at surfaces due to the surface polarization effect, that is, there is not observed any typical cloudy pattern that depends on the surface polarity49,50. The possibility of the flexoelectric instability is also excluded for the G or S textures. Such flexoelectric domains can only be observed in NLCs with low dielectric anisotropies and the applied electric field must be DC or AC at low frequencies51. Besides, the contribution of electrohydrodynamics can be ruled out because the tracer particles immersed do not exhibit a motion due to the LC flow. In fact, the electrohydrodynamic convection (EHC) pattern emerges, overlapping with the G texture for a proper cell thickness, as described later (Fig. 8b). Moreover, comparing the data denoted by open symbols in Fig. 3a shows that the Vth curve shifts to the low-frequency side as cell thickness d increases. The tendency is also distinct from that caused by the polar surface instability49,50. Furthermore, as the temperature increases, the G state returns to the H state, namely the Vth curve shifts to the high-frequency side. These results are also consistent if the ionic dynamics is considered and a more detailed description of the role of CYTOP is provided in the Discussion.
Spontaneous formation of a large single domain
The G state is usually accompanied by multi-domains (Fig. 2a). Therefore, in addition to elucidating the director field, realizing a large single domain is of particular interest because it has huge potential applications. We present a method for creating single domains by combining self-organization with a simple top-down approach. Two glass substrates with stripe-patterned ITO electrodes typically several hundreds of microns wide are prepared and they are placed so that the ITO stripes cross (Fig. 4a). Then, we apply an AC voltage to the square regions of the overlap of the ITO stripes. In this experiment, f is gradually increased with a constant V0 to transform the H state to the G state. First, uniform arrangements of umbilics are spontaneously formed along the edges of the square region (Fig. 4b, Supplementary Movie 1). These initial umbilics trigger the epitaxial growth of a unidirectional single domain of the umbilics, and the G domain spreads over the whole square region of the overlapped electrodes. About 1,000 defects are packed with a regular spacing in Fig. 4c. To fill the area completely requires several tens to a few hundred seconds, depending on the quality of the sample cells. In our experimental conditions, this approach can be used up to the submillimeter scale.
The micrographic appearance is changed dramatically by rotating the crossed polarizers (Fig. 4c–e). When the direction of the extended lines connecting the neighbouring umbilics is parallel to the polarizers, a square lattice pattern is observed. A slight rotation of the polarizers (Fig. 4e) allows the topological nature of umbilics to be observed. The rotational directions of the four brushes of the adjacent umbilics are opposite, reflecting the ±1 states. The contrast of the image is inverted by rotating the polarizers by 45°. Figure 4f,g shows the effects of inserting a full-wave retardation plate (λ-plate) into the setup in Fig. 4c,d, respectively. The blue (added retardation) and bright magenta (subtracted retardation) regions imply that the director field around +1 umbilics is considered to be a radial type rather than spiral one40. To support this consideration, fluorescent confocal polarizing microscopy observations are performed (Supplementary Fig. 1). This technique enables the director mapping by the intensity distribution of the polarized fluorescence from a doped emitter molecule transmitted through a polarizer inserted in the optical path52,53. An image taken at the middle plane of the cell agrees with our microscope observations. These observations lead to a texture consisting of two types of umbilics arranged in squares (Fig. 4h). In the present type of electrodes, the corner always has a hyperbolic hedgehog defect with −1 strength because of the topological constraint of the director field (Supplementary Fig. 2). The director deformation in the z-direction means that lens effects can be observed qualitatively by moving the objective focal plane of microscope (Supplementary Fig. 3).
Direct manipulation of defect arrays by laser irradiation
We show another important method for actively obtaining a large single domain without the edge effect of electrodes. We use an optical tweezers technique with an Nd-YAG laser (1,064 nm) to manipulate the local structure54. Owing to light-induced heating, the director in the laser spot returns to the perpendicular alignment, which can be seen as a dark spot (Fig. 5b and Supplementary Movie 2). After removing the laser spot, the director finds a more stable configuration while recovering its tilt angle. Thus, scanning the laser spot allows umbilics to rearrange to form uniform arrays (Fig. 5c). We can eventually create a domain on the sub-square centimetre scale (Fig. 5d). A larger scale would be possible by preparing ideal cells under clean room conditions.
Laser tweezing can be used to create or erase umbilics at arbitrary positions in the S state, which appears on the high-frequency side of the G state (Fig. 2). We use square electrodes, the edges of which form a regularly ordered S state (Fig. 6a). After preparing a single G domain, we adjust f at a fixed V0 to the conditions where the S state is slightly preferred over the G state. Then, the umbilics are irradiated with a laser to induce homeotropic alignment. After switching off the laser, the defects no longer appear and instead the more stable S state is obtained (Supplementary Movie 3). Once the S state is prepared, we can create artificial isolated umbilic arrays surrounded by the S domain (Fig. 6b). The whole area can be transferred from the S state to the G state (Supplementary Movie 4). Importantly, the S state can be obtained again by erasing umbilics, and thus the process is fully repeatable.
Flow-induced striped texture
Mechanical flow also affects the director field, n, substantially. When the NLC sample is introduced into the cell, the effect of capillary flow on the texture is visible. Here, we present an observation for a typical cell thickness of 4 μm. The flow speed cannot be controlled in our experimental conditions, because it depends on the cell gap and the observation area. Poiseuille flow occurs and the director profile can be regarded as two halves of the shear flow region55. The G structure changes to the S state as the sample flows during the injection (Supplementary Movie 5). The flow speed is estimated to be ∼8 μm s−1 from observation of the moving umbilics. The action of the flow aligns n along the flow direction and simultaneously distorts it in the orthogonal direction. This can be explained by investigating the effect of Poiseuille flow on the umbilics56. To apply simple shear, we prepare a setup consisting of a cell with its upper substrate fixed to a motorized translation stage without using spacers. The series of snapshots in Fig. 7 (Supplementary Movie 6) shows that the shear flow strongly affects the texture. Even this simple experiment demonstrates interesting properties. The lines of the grids normal to the shear direction degenerate and disappear, whereas those parallel to the shear directions remain (Fig. 7a). Once the shear is stopped, the G state is spontaneously recovered (Fig. 7b). Comparing the two adjacent lines normal to the shear direction shows that their behaviour is different. The position of the defects on the white dashed lines in Fig. 7a,c is almost unchanged under shear flow and the motion of the adjacent grid lines is opposite depending on the flow directions. This is because the bottom substrate is fixed (Fig. 7d). The blue and yellow strips exchange positions depending on the shear direction (compare the bottom figures of Fig. 7a,c). These behaviours are qualitatively consistent with the properties of umbilics. Details of the effect of mechanical flow on the G state will be reported in future work.
Tunable grid spacing
The spacing between umbilics can also be controlled. The grid size is measured by varying the cell thickness, d. Figure 8a shows that the size is almost proportional to d, which is tunable from several to hundreds of micrometres (Supplementary Fig. 4). This means that a thinner cell can generate high-density umbilics (Supplementary Fig. 5). For thick cells (for example, thicker than 20 μm in our experiments), the change in birefringence is clearly observed by polarization microscopy as the frequency increases (Supplementary Fig. 6). This is because the net birefringence is increased by the increase of the tilt angle, θ0, in the bulk (Fig. 1b). Further increases of the frequency cause electrohydrodynamic convection (EHC) (Fig. 8b). This is reasonable because EHC occurs for planar and homeotropic anchoring57,58. Even in the EHC region, the grid can be maintained with good stability. Because the director orientation is normal to the hydrodynamic rolls, the topological strength of umbilics is easily visualized by the direction of the rolls. This additional periodic modulation of the birefringence would offer interesting optical properties.
The size of the grid also depends on V0; the spacing increases with V0. Of course, f must be decreased simultaneously in accordance with Fig. 2. This property can be used to control of the number of grids in a single area dynamically (Fig. 8c and Supplementary Movie 7). The edge effect of the electrodes is important and helps to maintain the structure. Particularly in narrow electrodes, the high elastic energy cost due to the non-uniform deformation quickly relaxes to the single domain. Thus, the edges help produce a reproducible pattern when the field is switched on and off. We also confirm that even numbers of squares (or odd numbers of umbilics) are allowed inside the area because of the unique director configuration at the corner (Supplementary Fig. 2).
The variable grid spacing provides an interesting feature even for inhomogeneous arrangements. So far, we are mainly focusing on obtaining uniform square arrangements of umbilics. However, imperfect arrangements of umbilics often form dislocations like atomic crystals. This is a unique feature that is not observed in other analogue systems, such as two-dimensional bubble rafts59, because in our system liquid crystal umbilics mimic the atoms in crystals. Dislocations at a grain boundary can be generated artificially by using the acute corner of an oblique cross of the ITO strips (Fig. 9a). The umbilics tend to align along the edge of the electrodes and they prefer to be packed in squares; thus, grain boundaries appear. Three different cross-polarized conditions show three domains: two domains near the electrode edges and a central domain. Although the present system adds neither tensional nor compressional stress to the defect array in the cell (horizontal) plane, similar to the bubble raft system, frustration can be induced in the system by changing the grid size. Figure 9b shows a visualization of moving dislocations that are trying to reduce the frustration. The electric field is suddenly changed to a higher V0 and a lower f to increase the grid size (Fig. 8c), and then a lower density of umbilics is required to reach a stable state. Thus, because of the imposed elastic frustration, a pair of umbilics annihilates to generate two dislocations, and then these dislocations move apart to relax the structure. The time course is shown as snapshots in Fig. 9b (Supplementary Movie 8). The dislocation moves in the normal direction of the glide plane (or line). This is natural considering the energetics because this motion reduces the density of umbilics. This is a distinct difference from the atomic crystals where the dislocation moves parallel to the direction of the glide line because the atoms never annihilate.
Discussion
The G and S states can be obtained by the combination of dopant ions and a CYTOP layer with a proper thickness. Here, in this study, we consider the field-screening effect as mentioned above. In order to explain the sharp increase of Vth at low frequencies, we use the configuration shown in Fig. 3b to calculate the voltage applied to the cell. The dielectric constant is ɛLC, the electric conductivity is σLC, and the thickness of the NLC is d, and the corresponding terms for the alignment layer are ɛs, σs, and ls, respectively. The anisotropy of ɛLC and σLC is not considered and σLC includes the ionic contribution. The applied voltage is written as V=Vs+VLC, where and are the voltage drop in the alignment layer and in the NLC layer. Using the complex conductivity, and , a relation should hold due to the conservation of current density. The complex amplitude of the threshold voltage applied to the cell is described as . Low and high-frequency limits are evaluated by . Here CYTOP has a high volume resistivity of 1/σs>1015 Ω·m and a small dielectric constant of ɛs=2.0–2.1ɛ0 (ref. 48). The resistivity is at least around an order of magnitude greater than that of the polyimide surface (1010–1013 Ω·m) (ref. 60), while the dielectric constant is still comparable to that of polyimide and LCs, that is, ɛs∼ɛLC. It is a reasonable assumption that the electrical potential, VLC, necessary for the reorientation of n is almost the same as the Fréedericksz transition voltage of the pure NLCs shown in Fig. 3a, namely the rest of the applied voltage, V−VLC is used for the voltage drop in the alignment layer. We also note that ls/d<<1 holds because the thickness is ls∼120 nm in our standard spin-coating condition. Then the high-frequency region gives V∼{2(ɛLC/ɛs)(ls/d)+1}VLC∼VLC, because the dielectric constant is dominant. However, the conductivity becomes important at the low-frequency side and V can be approximated as V∼{2(σLC/σs)(ls/d)+1}VLC, which is greatly affected by the amount of doped ions σLC. Our preliminary evaluation of the effective conductivity of CCN-37 is of the order of 10−6 Ω−1 m−1 at 1 kHz, which is measured without using an alignment layer. Thus, the main reason can be assigned to the increased value of σLC. This supports our experimental data that show thicker cells lower the threshold voltage at the same frequency. Eventually the surface charge density, ρs, given by ρs=ɛ0{ɛLC(σLC/σs)−ɛs}(Vs/ls) in the low-frequency limit, becomes high. We can speculate that a high surface charge density is achieved on CYTOP after doping with ionic materials and that it creates a spatial distribution near the interface. The expression of ρs also supports the temperature dependence because the ionic localization around the surface develops faster owing to the increased mobility, μ∝σLC=σ0exp(−W/kBT) (ref. 46).
Since the qualitative behaviour of Vth is explained by considering the CYTOP surface, here, we present a detailed model that can reproduce the transition to the G state from the H state prior to achieving the U state. Based on the observations, the effects of the doped ions (TBABE) and the insulating layer (CYTOP) are considered. The details are provided in the Method section. We set the origin of the z-axis (z=0) at the center of the nematic slab (Fig. 10a). The NLC-CYTOP interfaces and the CYTOP-electrode interfaces are positioned at z=±d/2 and z=±h/2, respectively. We focus on calculating the threshold voltage from the H to G states. In our system, the electric potential is given as ϕ=0 at z=−h/2 and ϕ=V0cosωt at z=h/2, with . The slightly tilted n is expressed as n=(δnx,δny,1) and the corresponding potential becomes . The translational symmetry in the x-y plane allows us to write the solution for the grid pattern as
where the grid pattern described by equations (1)–(3), should be rotated by 45° when it is compared with the photos shown in Fig. 4. The threshold voltage can be regarded as a function of q, that is, V0(q). The real threshold voltage, Vth, is given by the minimum value of V0. A local minimum at q=0 corresponds to the transition to the U state, namely, the normal Fréedericksz transition, and another minimum at q≠0 corresponds to the transition to the G state. Because Vth depends on the frequency of the applied voltage, permittivities, conductivities, elastic constants and thicknesses of NLC and insulating films, the numerical calculations based on the continuum theory of NLCs are performed by using the typical material constants for the NLC and CYTOP, and our experimental conditions for d and l. The conductivities σ|| and σ⊥, which depend on the concentration of dopant ions, are chosen to reproduce the frequency dependence of Vth in Fig. 2b. The behaviour of V0(q) at different typical frequencies is shown in Fig. 10b. At low frequencies of f=70 and 200 Hz, the G state is more stable than the U state since the minimum of V0 is at q≠0. However, the two local minima of V0 at q=0 and q≠0 become close at 200 Hz. As the frequency is increased, they become equal (457.5 Hz) and eventually the U state becomes more stable (550 Hz). Calculating V0(q) by varying the frequencies allows us to plot Vth as a function of f (Fig. 10c). The magenta lines are the boundaries of the H–G transition with q≠0 and the black lines are those of the H–U transition with q=0. The blue solid circles indicate the intersection of the two lines. We cannot reproduce the G–S and S–U transitions because our numerical results are limited to the linear stability analysis. (i) in Fig. 10c corresponds to Fig. 2, where we use the same material constant values as in Fig. 10b. Good agreement is obtained, though the numerically obtained position of the boundary between the H–G and H–U transitions is located at a little bit higher frequency compared with the experiment. When the conductivities σ|| and σ⊥ are decreased ((ii) in Fig. 10c), the boundary between the H–G and H–U transitions shifts to a lower frequency, implying that the grid pattern is destabilized by the decrease in conductivities. In other words, the conductivity stabilizes the G state. However, when the thickness of the insulating films is reduced from 0.12 μm (l=3.24 μm) to 0.05 μm (l=3.1 μm) ((iii) in Fig. 10c), similar behaviour is observed, implying that the insulating film also stabilizes the grid state. If the conductivity is small or the film is thin, the grid state disappears ((iv) in Fig. 10c). These results clearly indicate that the enhanced conductivity of the NLC and the insulating CYTOP film play a crucial role in forming the G state.
To confirm these results, we test typical materials with negative dielectric anisotropy, such as MBBA (Sigma-Aldrich) and an NLC mixture, Phase 5 (Merck). They do not show normal anchoring on the CYTOP surface. For further experimental evidence, we need to use LC materials that induce homeotropic alignment on CYTOP.
In summary, we report unconventional pattern formation in NLCs by combining doped ions and a perfluoro polymer alignment layer. The creation of a large single domain of square arrays consisting of high-density defects is demonstrated in several ways. The system has huge advantages compared with previous systems because its self-organization offers highly tunable structures that do not require special surface modifications. The structure can be used directly for diffractive microlens arrays, generation of multiple vortex beams using LC mesophases36,61,62,63,64,65 as foreseen applications. Because our system is self-repairing, it could be applied for sensor applications using director distortion. Polymerizing the structure would provide a soft lithographic template for micro and nanostructures66. The stabilization of the grids may offer very interesting possibility to create freestanding films which provide exposed interfaces and are useful, such as for pixelated LC sensor applications in liquid or gaseous environments. Moreover, the system offers a playground for studying the fundamental physics of various fields such as microrheology and colloidal science. Our experimental results may shed light on creating unconventional LC textures using ionic effects. Although the data presented here are obtained under standard laboratory conditions, we believe that the quality can be improved substantially under clean and refined experimental conditions.
Methods
Sample preparation and cells
We use the NLC compounds CCN-mn (trans, trans-4, 4′-dialkyl-(1α, 1′α-bicyclohexyl-4β-carbonitriles, Nematel GmbH & Co. KG), which possess a negative dielectric anisotropy47. Particularly, CCN-37 and the 1:1 mixture of CCN-47 and CCN-55 are used in this work because they show the nematic phase at room temperature. Experiments are carried out at 25 °C unless otherwise indicated. Moreover, 1 wt% of an ionic compound tetrabutyl anmonium benzoate (TBABE, Aldrich) is mixed into NLCs. In preparing the ion-doped samples, the NLC and ions are diluted with chloroform and mixed by ultrasonic agitation for 1 h. Then, the chloroform is evaporated for 24 h.
The sample is filled in cells consisting of ITO coated glass substrates with a proper distance determined by standard interferometry. Monodisperse spherical particles are used as a spacer to maintain the cell thickness. The ITO-coated glass substrate is spin-coated by a thin layer of the amorphous perfluoro polymer (CYTOP, Asahi Glass Co.), which induces the perpendicular orientation of n to the glass surface44. In the process of our standard spin-coating, we mix the solute CTX-809A (a solution containing 9 wt% CYTOP, Asahi Glass Co.) and the solvent CT-Solv.180 (Asahi Glass Co.) with the weight ratio of 1:2. The spin-coating is made with 800 r.p.m. for 9 s and 3,000 r.p.m. for 15 s. After coating, the substrates are dried at 70 °C for 30 min and baked at 120 °C for longer than 30 min. The ratio of the solute and solvent is changed to obtain various thicknesses of the alignment layers. The thickness of the CYTOP layer is estimated by spectroscopic ellipsometry (SE-2000, SEMILAB Zrt.), whose results are 120 nm for 3 wt% solution and 17 nm for 1 wt% solution. As alternative alignment layers for homeotropic anchoring, a polyimide surface (SE-1211, Nissan chemical) and a surfactant mono layer (DMOAP, N,N-Dimethyl-N-octadecyl-3-aminopropyltrimethoxysilyl chloride, Aldrich) are tested. In the standard use of SE-1211, the stock solution is diluted with the dedicated solvent of equal amount. Spin-coating condition is the same as the CYTOP. In addition, the stock solution of SE-1211 itself is also coated with 1,000 r.p.m. to have a thicker alignment layer although a drastic change is not observed. In this condition, the thickness of SE-1211 amounts to 400 nm. For the latter case, glass substrates are taken into a water solution and 5 vol% DMOAP solution is added to it. After mixing for about 5 min, the excess surfactant is washed with pure water and the substrates are kept at 120 °C for 30 min for drying. The effective electrical conductivity is estimated by a LCR metre (E4980A, Agilent) using an ITO-coated glass cell without having alignment layers. It must be noted that the anisotropy is not accessible. The measured value is of the order of 10−6 Ω−1 m−1 at 1 kHz, which is used for the theoretical calculation.
To prepare patterned electrodes, ITO-coated glasses are fabricated by a standard photo etching method using a positive photoresist (TFR-2950 PM, Tokyo Ohka Kogyo Co., Ltd.). Finally, an AC voltage V=V0 cos (2πft) is applied between the ITO-coated glass substrates along the z-direction in order to reorient the director. For shear application, the upper and lower glass substrates are installed on the motorized stage separately without using spacers.
Polarization light microscope characterization
AC voltage from the function generator is amplified and applied to ITO-coated glasses so that the electric field is perpendicular to the substrates. The maximum amplitude of the output voltage V0 is 40 V. Texture observation is usually made by a polarizing microscope (Olympus BX51) under different illumination conditions. If necessary, the temperature controller is used. The micrographic appearance is taken by a DSL camera (Sony ILCE-7R). For our optical manipulation experiments, an Nd-YAG laser (1,064 nm) is irradiated to the sample cell on a motorized stage of an inverted microscope (Olympus IX71). The manipulation is made by moving the motorized stage.
Fluorescence confocal polarizing microscopy
A confocal laser scanning microscope Leica TCS sp8 is used for elucidating the director configuration of the G state. The NLC samples are doped with ∼0.01 wt% of a fluorescent dye, 7-diethylamino-3,4-benzophenoxazine-2-one (Nile red, Sigma-Aldrich). The Nile red molecules orient along the director field due to its shape anisotropy. Thin quartz glass plates of thickness 160 μm are used for sample cells. The laser with the wavelength of 552 nm excites the dye molecule and the emission is detected in the spectral region of 610–660 nm. The polarization of the incoming laser beam is adjusted manually with a combination of a quarter wave plate and a linear polarizer inserted in the laser path. Simultaneously, polarizing microscopy images by the ultraviolet transmitted mode are captured during confocal scans of the same sample.
Theoretical details
The charge density, ρ, satisfies the Poisson equation ∇·(ɛ E)=ρ and the charge conservation law ∇·(σ E)=−∂ρ/∂t, where E is the electric field, ɛ is the permittivity and σ is the conductivity. Here, the ion diffusion is neglected for simplicity. By using the electric potential ϕ, these equations are rewritten as
In NLCs, ɛ and σ are functions of n
with ɛa=ɛ||−ɛ⊥ and σa=σ||−σ⊥, where || and ⊥ denote the components of permittivity (or conductivity) parallel and perpendicular to n, respectively. ɛs and σs are the permittivity and conductivity of the insulating film, which also imposes a condition of σs<<σ||, σ⊥.
On the other hand, director n follows the torque balance equation
where free energy F consists of the Frank elastic energy, fd and the electric-field contribution, fel as
We neglect the contribution of the NLC flow because there is no observable EHC effect, except for in Fig. 8b. ɛ and σ are time-independent constants in equations (4) and (5) because the relaxation time of the director fluctuations near the threshold voltage is much longer than the period of the AC electric field. Under these conditions, we obtain from equations (4) and (5)
with
Application of Gauss’s theorem to equation (11) at the NLC-CYTOP interface gives the boundary conditions of
in addition to the continuity of potential of
where superscripts (I) and (II) denote the NLC and CYTOP, respectively, and are used hereafter.
For the homeotropic state, we can easily obtain potential from the above equations. The corresponding electric field has only the z component of
where and . Substituting n=(δnx,δny,1) and into equations (8)–(14), and linearizing the results with respect to δnx,δny and , we obtain
where and . The last terms of equations (17) and (18) are replaced by the time average over the period of the applied voltage because the director fluctuations become slow near the threshold.
The translational symmetry in the x-y plane allows us to write the solution for the grid pattern as equations (1)–(3),. Substitution of equations (1)–(3), into equations (17)–(23), yields
Equations (17) and (18) are reduced to the same equation (24), and the boundary conditions for are obtained by replacing with in equations (22) and (23). At threshold voltage Vth, the relaxation time diverges so that the time derivative term on the left-hand side of equation (24) vanishes. Then, equation (24) with , together with the other equations (25)–(27), gives Vth. The above equations (24)–(27), cannot be solved analytically for general cases h≠d, except for h=d. Then, we briefly explain how to calculate Vth numerically. Expressing , we have three equations for three quantities and from equations (24)–(27),. Substitution of θ=θ0eλz, , and gives a system of homogeneous linear equations for , which can only be solved if the determinant vanishes. Because there are two derivatives, and , in equations (24)–(27), we have a cubic equation with respect to λ2. Furthermore, from the symmetry of the above equations (24)–(27), the solutions can be classified into odd and even functions of z, and the latter gives the minimum threshold voltage. Thus, the solution can be expressed as u=c1u1coshλ1z+c2u2coshλ2z+c3u3coshλ3z, where is the eigenvalue and ui is the corresponding eigenvector. In the insulating film (d/2<z<h/2), whereas the potential is obtained as after imposing the boundary condition . Substitution of these equations into the other boundary conditions yields a system of homogeneous linear equations for ci, the determinant of which is a function of V0 and q, and vanishes at the threshold voltage for a given q.
Data availability
The authors declare that the data supporting the findings of this study are available within the article and its Supplementary Information files.
Additional information
How to cite this article: Sasaki, Y. et al. Large-scale self-organization of reconfigurable topological defect networks in nematic liquid crystals. Nat. Commun. 7, 13238 doi: 10.1038/ncomms13238 (2016).
References
Hamley, I. W. Nanotechnology with soft materials. Angew. Chemie Int. Ed. 42, 1692–1712 (2003).
Wang, D. & Möhwald, H. Template-directed colloidal self-assembly—the route to ‘top-down’ nanochemical engineering. J. Mater. Chem. 14, 459–468 (2004).
Huang, Y., Wang, X., Duan, Y., Bu, N. & Yin, Z. Controllable self-organization of colloid microarrays based on finite length effects of electrospun ribbons. Soft Matter 8, 8302–8311 (2012).
Cheng, J. Y., Mayes, A. M. & Ross, C. A. Nanostructure engineering by templated self-assembly of block copolymers. Nat. Mater. 3, 823–828 (2004).
Cheng, J. Y., Ross, C. A., Smith, H. I. & Thomas, E. L. Templated self-assembly of block copolymers: top-down helps bottom-up. Adv. Mater. 18, 2505–2521 (2006).
Yoon, D. K. et al. Internal structure visualization and lithographic use of periodic toroidal holes in liquid crystals. Nat. Mater. 6, 866–870 (2007).
Yoon, D. K. et al. Orientation of a helical nanofilament (B4) liquid-crystal phase: topographic control of confinement, shear flow, and temperature gradients. Adv. Mater. 23, 1962–1967 (2011).
Orihara, H. & Ishibashi, Y. Dynamics of disclinations in twisted nematics quenched below the clearing point. J. Phys. Soc. Jpn 55, 2151–2156 (1986).
Chuang, I., Durrer, R., Turok, N. & Yurke, B. Cosmology in the laboratory: defect dynamics in liquid crystals. Science 251, 1336–1342 (1991).
Araki, T., Buscaglia, M., Bellini, T. & Tanaka, H. Memory and topological frustration in nematic liquid crystals confined in porous materials. Nat. Mater. 10, 303–309 (2011).
Ohzono, T. & Fukuda, J. Zigzag line defects and manipulation of colloids in a nematic liquid crystal in microwrinkle grooves. Nat. Commun. 3, 701 (2012).
Lavrentovich, O. D. Topological defects in dispersed liquid crystals, or words and worlds around liquid crystal drops. Liq. Cryst. 24, 117–125 (1998).
Fernández-Nieves, A. et al. Novel defect structures in nematic liquid crystal shells. Phys. Rev. Lett. 99, 157801 (2007).
Muševič, I., Škarabot, M., Tkalec, U., Ravnik, M. & Žumer, S. Two-dimensional nematic colloidal crystals self-assembled by topological defects. Science 313, 954–958 (2006).
Lapointe, C. P., Mason, T. G. & Smalyukh, I. I. Shape-controlled colloidal interactions in nematic liquid crystals. Science 326, 1083–1086 (2009).
Wang, X., Miller, D. S., Bukusoglu, E., de Pablo, J. J. & Abbott, N. L. Topological defects in liquid crystals as templates for molecular self-assembly. Nat. Mater. 15, 106–112 (2016).
Buka, A. & Kramer, L. Pattern Formation in Liquid Crystals Springer New York (1996).
Meyer, R. B. Piezoelectric effects in liquid crystals. Phys. Rev. Lett. 22, 918–921 (1969).
Kuzma, M. R. Nonequilibrium periodic structures induced by rotating and static fields in a lyotropic nematic liquid crystal. Phys. Rev. Lett. 57, 349–352 (1986).
Barnik, M. I., Blinov, L. M., Trufanov, A. N. & Umanski, B. A. Flexo-electric domains in liquid crystals. J. Phys. 39, 417–422 (1978).
Chigrinov, V. G., Korkishko, T. V., Barnik, M. I. & Trufanov, A. N. Freedericksz transition in electric fields near the dielectric sign reversal frequency. Mol. Cryst. Liq. Cryst. 129, 285–300 (1985).
Lonberg, F., Fraden, S., Hurd, A. J. & Meyer, R. E. Field-induced transient periodic structures in nematic liquid crystals: the twist-Fréedericksz transition. Phys. Rev. Lett. 52, 1903–1906 (1984).
Pieranski, P., Dubois-Violette, E. & Guyon, E. Heat convection in liquid crystals heated from above. Phys. Rev. Lett. 30, 736–739 (1973).
Lavrentovich, O. D. & Pergamenshchik, V. M. Stripe domain phase of a thin nematic film and the K13 divergence term. Phys. Rev. Lett. 73, 979–982 (1994).
Lavrentovich, O. D. & Pergamenshchik, V. M. Patterns in thin liquid crystal films and the divergence (‘surfacelike’) elasticity. Int. J. Mod. Phys. B 9, 2389–2437 (1995).
Buka, Á., Dressel, B., Kramer, L. & Pesch, W. Isotropic convection scenarios in an anisotropic fluid. Phys. Rev. Lett. 93, 044502 (2004).
Kim, J.-H., Yoneya, M. & Yokoyama, H. Tristable nematic liquid-crystal device using micropatterned surface alignment. Nature 420, 159–162 (2002).
Murray, B. S., Pelcovits, R. A. & Rosenblatt, C. Creating arbitrary arrays of two-dimensional topological defects. Phys. Rev. E 90, 052501 (2014).
Youngwoo, Y., Nakata, M., Martin, A. R. & Clark, N. A. Alignment of liquid crystals by topographically patterned polymer films prepared by nanoimprint lithography. Appl. Phys. Lett. 90, 163510 (2007).
Crawford, G. P., Eakin, J. N., Radcliffe, M. D., Callan-Jones, A. & Pelcovits, R. A. Liquid-crystal diffraction gratings using polarization holography alignment techniques. J. Appl. Phys. 98, 123102 (2005).
Yoshida, H., Asakura, K., Fukuda, J. & Ozaki, M. Three-dimensional positioning and control of colloidal objects utilizing engineered liquid crystalline defect networks. Nat. Commun. 6, 7180 (2015).
McConney, M. E. et al. Topography from topology: photoinduced surface features generated in liquid crystal polymer networks. Adv. Mater. 25, 5880–5885 (2013).
Wei, B. et al. Generating switchable and reconfigurable optical vortices via photopatterning of liquid crystals. Adv. Mater. 26, 1590–1595 (2014).
Slussarenko, S. et al. Tunable liquid crystal q-plates with arbitrary topological charge. Opt. Express 19, 4085–4090 (2011).
Zhang, J., Boamfa, M. I., Rowan, A. E. & Rasing, T. Compartmentalized multistable liquid crystal alignment. Adv. Mater. 22, 961–965 (2010).
Brasselet, E. Tunable optical vortex arrays from a single nematic topological defect. Phys. Rev. Lett. 108, 087801 (2012).
Loussert, C., Delabre, U. & Brasselet, E. Manipulating the orbital angular momentum of light at the micron scale with nematic disclinations in a liquid crystal film. Phys. Rev. Lett. 111, 037802 (2013).
Barboza, R., Bortolozzo, U., Clerc, M. G., Residori, S. & Vidal-Henriquez, E. Optical vortex induction via light–matter interaction in liquid-crystal media. Adv. Opt. Photon. 7, 635–683 (2015).
Murakami, N. et al. An eight-octant phase-mask coronagraph. Publ. Astron. Soc. Pacific 120, 1112–1118 (2008).
Rapini, A. Umbilics: static properties and shear-induced displacements. J. Phys. 34, 629–633 (1973).
Rapini, A., Léger, L. & Martinet, A. Umbilics: static and dynamic properties. J. Phys. Colloq. 36, C1–189–C1–196 (1975).
Nagaya, T., Hotta, H., Orihara, H. & Ishibashi, Y. Observation of annihilation process of disclinations emerging from bubble domains. J. Phys. Soc. Jpn 60, 1572–1578 (1991).
Dierking, I., Marshall, O., Wright, J. & Bulleid, N. Annihilation dynamics of umbilical defects in nematic liquid crystals under applied electric fields. Phys. Rev. E 71, 061709 (2005).
Dhara, S. et al. Anchoring transitions of transversely polar liquid-crystal molecules on perfluoropolymer surfaces. Phys. Rev. E 79, 060701(R) (2009).
Jeong, S. M. et al. Perfluoropolymer surface for shock-free homeotropic alignment of smectic liquid crystals. Adv. Mater. 22, 34–38 (2010).
Blinov, L. M. & Chigrinov, V. G. Electrooptic Effects in Liquid Crystal Materials Springer New York (1994).
Sai, D. V., Zuhail, K. P., Sarkar, R. & Dhara, S. Structure–property correlation of bicyclohexane nematic liquid crystals. Liq. Cryst. 42, 328–333 (2015).
Walser, M. P., Kalb, W. L., Mathis, T. & Batlogg, B. Low-voltage organic transistors and inverters with ultrathin fluoropolymer gate dielectric. Appl. Phys. Lett. 95, 233301 (2009).
Monkade, M., Martinot-Lagarde, P. & Durand, G. Electric polar surface instability in nematic liquid crystals. Europhys. Lett. 2, 299–305 (1986).
Lavrentovich, O. D., Nazarenko, V. G., Sergan, V. V & Durand, G. Dielectric quenching of the electric polar surface instability in a nematic liquid crystal. Phys. Rev. A 45, R6969–R6972 (1992).
Blinov, L. M. Domain instabilities in liquid crystals. J. Phys. Colloq. 40, C3–247–C3–258 (1979).
Smalyukh, I. I., Shiyanovskii, S. V. & Lavrentovich, O. D. Three-dimensional imaging of orientational order by fluorescence confocal polarizing microscopy. Chem. Phys. Lett. 336, 88–96 (2001).
Smalyukh, I. I., Zribi, O. V., Butler, J. C., Lavrentovich, O. D. & Wong, G. C. L. Structure and dynamics of liquid crystalline pattern formation in drying droplets of DNA. Phys. Rev. Lett. 96, 177801 (2006).
Jampani, V. S. R., Škarabot, M., Takezoe, H., Muševič, I. & Dhara, S. Laser-driven microflow-induced bistable orientation of a nematic liquid crystal in perfluoropolymer-treated unrubbed cells. Opt. Express 21, 724–729 (2013).
Sengupta, A., Herminghaus, S. & Bahr, C. Opto-fluidic velocimetry using liquid crystal microfluidics. Appl. Phys. Lett. 101, 164101 (2012).
Pieranski, P. Generation of umbilics by Poiseuille flows. Eur. Phys. J. E 37, 24 (2014).
Nishioka, Y., Kobayashi, F., Sakurai, N., Sasaki, Y. & Orihara, H. Microscopic characterisation of self-assembled colloidal particles in electrohydrodynamic convection of a low-birefringence nematic liquid crystal. Liq. Cryst. 43, 427–435 (2016).
Buka, Á., Tóth, P., Éber, N. & Kramer, L. Electroconvection in homeotropically aligned nematics. Phys. Rep. 337, 157–169 (2000).
Bragg, L. & Nye, J. F. A dynamical model of a crystal structure. Proc. R. Soc. A Math. Phys. Eng. Sci. 190, 474–481 (1947).
Fukuro, H., Sawahata, K., Sato, T. & Endo, H. Optimal alignment materials and technologies for various LCDs. SID Symp. Dig. Tech. Pap. 31, 434–437 (2000).
Barboza, R. et al. Harnessing optical vortex lattices in nematic liquid crystals. Phys. Rev. Lett. 111, 093902 (2013).
Yang, B. & Brasselet, E. Arbitrary vortex arrays realized from optical winding of frustrated chiral liquid crystals. J. Opt. 15, 044021 (2013).
Son, B. et al. Optical vortex arrays from smectic liquid crystals. Opt. Express 22, 4699–4704 (2014).
Loussert, C., Kushnir, K. & Brasselet, E. Q-plates micro-arrays for parallel processing of the photon orbital angular momentum. Appl. Phys. Lett. 105, 121108 (2014).
Schmitz, C. H. J., Uhrig, K., Spatz, J. P. & Curtis, J. E. Tuning the orbital angular momentum in optical vortex beams. Opt. Express 14, 6604–6612 (2006).
Dierking, I. & Archer, P. Imaging liquid crystal defects. RSC Adv. 3, 26433–26437 (2013).
Acknowledgements
This work was supported by JSPS KAKENHI Grant Number JP25103006 and by the Foundation for the Promotion of Ion Engineering.
Author information
Authors and Affiliations
Contributions
Y.S., V.S.R.J., C.T., N.S., S.S., K.V.L. and F.A. performed experiments. H.O. performed theoretical analysis. V.S.R.J., F.A. and H.O. designed the project. Y.S., V.S.R.J., K.V.L., F.A. and H.O. wrote the manuscript. All authors have seen and approved the final manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Information
Supplementary Figures 1-6 (PDF 890 kb)
Supplementary Movie 1
Template-assisted self-organization of grid-like pattern. The frequency of the electric field is gradually increased to induce grid-like pattern from homeotropic alignment. The amplitude of the field is kept at a constant value. The speed of the movie is 2x of the original one. The cell thickness is 4.9 μm and the NLC used is CCN-37. (AVI 1429 kb)
Supplementary Movie 2
Creation of a single domain of grid-like pattern by optical manipulation. The central dark spot shows homeotropic alignment induced by laser irradiation. The manipulation is made by moving a motorized translation stage. The speed of the movie is 2x of the original one. The cell thickness is 3.0 μm and the 1:1 mixture of CCN-47 and CCN-55 is used. (AVI 2939 kb)
Supplementary Movie 3
Creation of striped pattern from grid-like pattern. The laser beam is irradiated to a defect to induce homeotropic state and then it is switched off. The frequency is adjusted to the condition where the striped pattern is slightly preferred over the grid-like one. The cell thickness is 3.2 μm and the NLC used is CCN-37. (AVI 1117 kb)
Supplementary Movie 4
A single domain of grid-like texture created from striped domain. The grid-like pattern is created by irradiating laser beam. The speed of the movie is 5x of the original one. The cell thickness is 3.2 μm and the NLC used is CCN-37. (AVI 2620 kb)
Supplementary Movie 5
Striped domain created by capillary flow. This observation is made when the sample is introduced into the cell. The cell thickness is 3.7 μm and the NLC used is CCN-37. (AVI 886 kb)
Supplementary Movie 6
Effect of shear flow on grid-like texture. The simple shear flow is applied by moving a side of glass substrate which is attached on the motorized translation stage. The NLC is the mixture of CCN-47 and CCN-55. Here the cell thickness is not measured. (AVI 1820 kb)
Supplementary Movie 7
Reproducible grid-like pattern of umbilics. The cell thickness is 3.7 μm and the NLC used is CCN-37. (AVI 1090 kb)
Supplementary Movie 8
Motion of the dislocations formed by imperfect arrangement of umbilics. Frustration is induced into the system by changing the amplitude and the frequency of the electric field. The speed of the movie is 10x of the original. The cell thickness is 3.0 μm. The NLC is the 1:1 mixture of CCN-47 and CCN-55. (AVI 2009 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Sasaki, Y., Jampani, V., Tanaka, C. et al. Large-scale self-organization of reconfigurable topological defect networks in nematic liquid crystals. Nat Commun 7, 13238 (2016). https://doi.org/10.1038/ncomms13238
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms13238
- Springer Nature Limited
This article is cited by
-
Oblique light incidence method to study topological defects in nematic layers with conical boundary conditions
Scientific Reports (2021)
-
Coexisting multi-states in catalytic hydrogen oxidation on rhodium
Nature Communications (2021)
-
Electrically-tunable positioning of topological defects in liquid crystals
Nature Communications (2020)
-
Topological transitions in an oscillatory driven liquid crystal cell
Scientific Reports (2020)
-
Nanoparticle-Stabilized Lattices of Topological Defects in Liquid Crystals
International Journal of Thermophysics (2020)