Abstract
Fault zones accommodate relative motion between tectonic blocks and control earthquake nucleation. Nanocrystalline fault rocks are ubiquitous in “principal slip zones” indicating that these materials are determining fault stability. However, the rheology of nanocrystalline fault rocks remains poorly constrained. Here, we show that such fault rocks are an order of magnitude weaker than their microcrystalline counterparts when deformed at identical experimental conditions. Weakening of the fault rocks is hence intrinsic, it occurs once nanocrystalline layers form. However, it is difficult to produce “rate weakening” behavior due to the low measured stress exponent, n, of 1.3 ± 0.4 and the low activation energy, Q, of 16,000 ± 14,000 J/mol implying that the material will be strongly “rate strengthening” with a weak temperature sensitivity. Failure of the fault zone nevertheless occurs once these weak layers coalesce in a kinematically favored network. This type of instability is distinct from the frictional instability used to describe crustal earthquakes.
Similar content being viewed by others
Introduction
Fault zones are complex geological structures where deformation partitions and localizes into high-strain and low-strain domains over a wide range of length scales1,2. The interactions and feedbacks between the domains ultimately determine the mode of fault slip, from earthquakes, slow slip to viscous creep2. Localization in the high-strain domains is a pre-requisite for numerous weakening mechanisms such as thermal pressurization3,4 and shear heating5,6 that may induce weakening and may lead to an earthquake instability7. Furthermore, the material where strain localizes becomes profoundly transformed; high local work input induced by localization promotes comminution8, metamorphic reactions9,10,11, microstructural transformations12,13, phase transitions14,15 and melting16,17,18 that can locally weaken the fault rocks over a broad range of pressure, temperature (P-T) and strain rate conditions and produce nanocrystalline to amorphous materials in nature19,20,21 as well as in experiments16,22,23,24,25.
The rheology of these fine-grained fault rocks in zones of extreme localization is therefore critical for understanding fault slip14,26,27, yet it remains poorly constrained. Because of a lack of appropriate experimental studies, current models of nanocrystalline fault rock rheology rely on microstructural inferences and extrapolations of flow laws derived for microcrystalline materials27. These extrapolations, however, result in large uncertainties since nanocrystalline, surface dominated, materials typically have physical and mechanical properties that are distinct from microcrystalline, volume dominated, materials28.
Nanocrystalline fault rocks typically form compact zones with little to no porosity, composed of crystals (1’s–10’s of nm) to crystal aggregates (100’s of nm) that are sometimes embedded in an amorphous matrix12,14,16,22,23,26,29,30. The small grain size and associated short diffusional distances in combination with highly disordered lattices make diffusion competitive at conditions where cataclastic flow typically dominates26,31. Numerous lines of evidence suggest that the nanocrystalline fault rocks are weaker than the surrounding, coarser-grained, material and flow even at low ambient temperatures12,26,32. The exact cause of this weakening is, however, difficult to pin-point as several processes operate in parallel and could be responsible.
The principal problem in determining the rheology of nanocrystalline fault rocks is in isolating their intrinsic properties from the mechanical signal which is dominated by coarser-grained material in low velocity, small-displacement experiments22,24,26. In high velocity, large-displacement experiments, temperature transients make it difficult to untangle the effect of heating from the effects of nanomaterial formation23,32,33,34,35. At what stage of fault slip did the material form? Did the material reach high temperatures during slip? Is the nanocrystalline material the cause or the consequence of failure?
To circumvent these problems, we have produced granitoid nanomaterials in bulk by high-energy ball milling (details in “Methods”) and tested their rheological properties using a solid medium deformation apparatus under controlled P-T conditions corresponding to the base of the seismogenic layer where many large earthquakes nucleate.
Results
Mechanical properties of granitoid nanometric fault rocks
The nanomaterials are prepared from crushed granitoid gouge of the same origin as used in the previous studies12,30,31. Examination under scanning electron microscope using back-scattered electrons (SEM-BSE; Supplementary Fig. 1) shows that all minerals are thoroughly mixed due to ball milling, so it is impossible to distinguish individual grains. The material is cohesive and of uniform gray in BSE images suggesting a uniform chemical composition. Initial grain size determined by laser particle sizer is 0.01 ≤ d ≤ 1 μm, with a median of ~100 nm. More properties of the starting materials and a detailed explanation of the experimental procedures are described in “Methods”.
We compare the grain-size dependent strength of the fault rocks using constant-displacement-rate experiments (Methods, Fig. 1a). Note that microcrystalline experiments develop patches of nanocrystalline material with increasing strain that interconnect at peak stress and allow for failure24,30. All experiments were conducted in a general shear geometry at temperatures, T = 200, 300 and 500 °C and confining pressures, Pc = 500 MPa at a constant displacement rate of ~10−3 mm s−1, corresponding to a shear strain rate, \(\dot{\gamma },\) of ~10−3 s−1. As shown in Fig. 1, the strength of the granitoid fault rocks is clearly decreased due to the reduced grain size. Furthermore, the material with starting grain size of ≤ 200 μm showed an abrupt stress-drop at 300 °C, a laboratory equivalent to an earthquake36, but the nanomaterial creeps with no loss of strength at the same temperature. With the increase of temperature, the maximum shear stress (τ), apparent viscosity (\(\eta =\tau /\dot{\gamma }\)), and friction coefficient (μ = τ/σn, where σn is the normal stress) are all decreased for both grain sizes, indicating that the materials become weaker with increasing temperature (Fig. 1b; Table 1). The nanocrystalline fault rocks at 200 °C and 300 °C both show strain hardening after the yield point. The hardening rate decreases with increasing temperature. At 500 °C, both the microcrystalline as well as the nanocrystalline materials continue to deform at approximately constant stress implying that the rocks have reached steady-state flow. Flow in the microcrystalline experiment is accommodated by ≈20 vol% of nanocrystalline material that is produced during shearing30. Only for the nanocrystalline fault rocks, the differential stress, ∆\(\bar{\sigma }\), is just below the Goetze criterion (∆\(\bar{\sigma }\) ≤ Pc).
To further constrain the rheology of the nanocrystalline fault rocks, we quantitatively investigate the stress exponent, n (Fig. 1c) using stress-stepping experiments and estimate the activation energy, Q (Fig. 1d) using the constant-displacement-rate experiments (Methods, Supplementary Fig. 3, Table 1). The stress-stepping experiments indicate that the nanocrystalline fault rocks exhibit a near-linear stress–strain rate relationship with a stress exponent, n = 1.3 ± 0.4, for temperatures ranging from 300 to 500 °C. Constant-displacement-rate experiments provide an estimation of the activation energy, \(Q={{{{\mathrm{16,000}}}}}\pm {{{{\mathrm{14,000}}}}}\ {{{{{\rm{J}}}}}}/{{{{{\rm{mol}}}}}}\), for stress exponent of 1.3. Hence, the flow law for granitoid nanometric fault rocks is determined as
where \(\bar{\sigma }\) is equivalent stress in MPa, \(\dot{\bar{\varepsilon }}\), equivalent strain rate in s−1, R, gas constant, of 8.314 J/ (mol·K), T, absolute temperature in Kelvin. The unit of the activation energy in the exponential term is in J/mol. Further verification of the flow law shows that the calculated strain rates compare well to the measured strain rates in the constant displacement rate experiments (Supplementary Fig. 4, Supplementary Table 1). Hence, it appears that nanometric fault rocks can dominantly deform by diffusion creep—as suggested by the characteristic stress exponent of ~137 - even at low temperatures and fast experimental strain rates. While the stress exponent is consistent with microcrystalline materials deforming dominantly by diffusion creep, the activation energy is substantially lower in the nanocrystalline fault rocks. Low activation energies are expected for nanomaterials due to the high surface-to-volume ratio; it requires less energy to free an atom from the surface since the atoms in nanomaterials have on average fewer bonds with neighboring atoms compared to coarser-grained materials38,39.
At all studied temperatures, the nanocrystalline material deformed in a stable manner without any abrupt stress drops (Fig. 1a).
Microstructures of nanocrystalline fault rocks
To constrain active deformation mechanisms, we studied the resulting microstructures using high-resolution SEM and polarized light microscopy. At low temperatures of 200–300 °C, Riedel shear fractures are ubiquitous with distinctive geometric relationships typical for a shear zone (Figs. 2 and 3). The R1 Riedel shear fractures make a low angle of 160° with the shear zone boundary and show the same sense of slip. R2-shear fractures are found at an angle of 65–85° with respect to the shear zone boundary. The cross-cutting relationships between R1-shears and R2-shears indicate that the R2-shears develop after the establishment of R1-shear fractures. At 300 °C, optical anisotropy gets more pronounced and kink bands are visible as alteration of yellow/purple and blue along the R2 Riedel shear orientation (Fig. 2c). These kink bands nucleate at the extremities of the forcing blocks, migrate inwards with increasing strain (Figs. 2c, 3c, d and Supplementary Fig. 7e, 7f), and suggest that the material is mechanically anisotropic. Porosity due to opening of R1 and R2 fractures indicates bulk dilatancy at low temperatures (200 and 300 °C) coinciding with strain hardening behaviors and differential stresses above the Goteze criterion (Fig. 1a).
In contrast, fractures are much less common when the material is deformed at 500 °C in agreement with the mechanical steady-state and stresses below the Goetze criterion (Fig. 1a). Almost all the visible fractures are unloading cracks with some R2-oriented fractures aligned “en-echelon” in the R1 orientation (Fig. 2d). Optical anisotropy is further strengthened as evidenced by more saturated interference colors (Fig. 2d). Flow features, such as smeared out domains of slightly different z-contrast, dominate suggesting that the deformation is continuous (Figs. 2d, 3e and Supplementary Fig. 7). These observations, together with the mechanical data, suggest that the material deforms as a volume-conserving viscous fluid at 500 °C.
Transmission electron microscopy (TEM) confirms that the material at 500 °C is compact with no porosity and composed of crystals with a mean grain size of 46 nm (Fig. 4). Silicate grains are rounded (aspect ratio, b/a ≈ 0.9) with no strong shape preferred orientation (SPO) visible in a section parallel to their flow direction, whereas micas show strong SPO (b/a ≈ 0.4) (Supplementary Fig. 8). Selected area diffraction patterns document that the material is crystalline and does not show a crystallographic preferred orientation (CPO, Fig. 4b).
Our observations of strong and spatially coherent optical anisotropy are surprising given the grain size is about an order of magnitude smaller than the wavelength of visible light (Fig. 3 and Supplementary Fig. 9). Similar coherent optical anisotropy was observed in nanocrystalline slip zones developed in low-pressure friction experiments conducted with calcite fault gouge40,41 suggesting that optical anisotropy is common in nanocrystalline fault rocks. While the usual cause of spatially coherent optical anisotropy in microcrystalline materials is a strong CPO, it seems more likely that here the optical anisotropy occurs due to interactions of the nanoparticles with passing light forming optical sub-wavelength grating effects42.
Discussion
In the traditional view of earthquake instability, a decrease in friction coefficient with increasing sliding velocity (“velocity weakening” behavior) is one of the necessary pre-requisites for earthquake nucleation43. Although the nanometric flow is believed to play a key role in the earthquake instability14,26,27, it is difficult to produce “velocity weakening” behavior in viscous fluids especially if they have low-stress exponents. Figure 5a shows the effective stress–strain rate variation at various temperatures calculated using the flow law for nanometric fault rocks. For example, if the strain rate accelerates from \({\dot{\bar{\varepsilon }}}_{0}\) to \({\dot{\bar{\varepsilon }}}_{1}\), the effective stress will increase as determined by the stress exponent, n ~1.3 (rate-strengthening behavior; Fig. 5a). Theoretically, an increase of temperature due to shear heating could reduce the viscosity of the material, such that the material would be weaker at the higher strain rates (Fig. 5a). However, the low activation energy of the nanomaterial (16,000 ± 14,000 J/mol) precludes an effective temperature-induced weakening effect over a broad range of equivalent stress and ambient temperature conditions. Figure 5b shows the temperature increase (steady-state temperature minus ambient temperature) due to shear heating in the nanocrystalline fault rocks at conditions that could be prevalent at the base of the seismogenic layer (details of the shear heating calculation are in “Methods”). Extremely high equivalent stresses on the order of tens of GPa are required for a modest increase of temperature, meaning that shear-heating instability6,44 is unlikely to be the cause of velocity weakening for the nanometric fault rocks. The nanometric fault rocks resist high-velocity deformation and act as viscous breaks. Yet, we observe abrupt failure—a laboratory equivalent of an earthquake—in the microcrystalline experiment at 300 °C where strain localization produces 10–15 vol% of nanocrystalline material30.
The rheological behavior of the nanocrystalline material suggests a possible weakening mechanism that may lead to an earthquake instability. Fault weakening occurs due to the intrinsic low viscosity of the nanocrystalline fault rocks. Shearing of coarse-grained fault rocks locally leads to comminution and patchy production of nanocrystalline material22,30, the volume occupied by these nanocrystalline materials increases with increasing work and homologous temperature24,45, eventually reaching a percolation threshold. Although the extremely fine-grained material is rate-strengthening, it has a much lower viscosity (Figs. 1, 5b) than the surrounding material. Once this material is generated in sufficient quantities and forms a kinematically favorable failure plane, the fault displacement may accelerate on this lower viscosity layer at the same stress level and in the absence of significant temperature increase potentially leading to an earthquake instability.
The proposed weakening model here is distinguished from the usual frictional instability but may be analogous to the mechanism causing deep earthquakes, which involve phase transitions14,15,46, shear-heating induced visco-elastic deformation6, and “cavitation” based models where a porosity layer coalesces into a failure plane41. All these processes have as a common characteristic that there is a weak but rate-strengthening layer. Experiments studying the initialization of deep earthquakes show that shear failure of solid rock at high pressure is possible in the presence of a small amount of low-viscosity material: either a polycrystalline solid that is extremely weak or a true fluid47. In our experiments, the nanometric fault rocks deform like a viscous fluid and are extremely weak. This suggests that shearing instability due to weak inclusions may not only be the cause of deep earthquakes but may also plausibly operate in the crust, particularly around the brittle-viscous transition zone where many large earthquakes nucleate.
Methods
Deformation of granitoid nanocrystalline and microcrystalline fault rocks at seismogenic P-T conditions.
Starting materials
The nanomaterials are prepared from crushed Verzasca gneiss powder (d ≤ 200 µm) of the same origin as the microcrystalline fault rocks described in previous studies12,30,31. Image analysis of BSE micrographs shows that the initial powder material consists of 37% quartz (Qtz), 33% plagioclase (Plg), 28% potassium feldspar (Kfs) and minor micas (~2%). Chemical analysis by X-ray fluorescence (XRF) shows that the starting powder consists of 77 wt% SiO2, 13.3 wt% Al2O3, 4.63 wt% K2O, 3.16 wt% Na2O, and ≤1 wt% of other elements30.
To grind this material down to nanometric size, the powder is milled for a total of 12 min in deionized water with 0.1 mm diameter zirconia balls using a planetary ball mill (Fritsch Pulverisette 7). After each ~2 min of milling, the holder is left to cool for ~20 min. As the milling is performed in water the temperature increase during milling is buffered at ≤100 °C. The particle size distribution of the unsheared starting material falls in the range 0.01 ≤ d ≤ 1 μm, with a median of ~0.1 μm as determined by a laser particle meter (Fritsch Analysette 22). Note that this measurement likely represents the “apparent” grain size as nanoparticles tend to cluster together48. After the milling, the powders are dried in an oven at 110 °C for >48 h to evaporate any residual H2O. Supplementary Fig. 1 shows the SEM-BSE and secondary electron (SE) topographic images of the dried nanomaterial. All minerals are mixed due to ball milling so it is impossible to distinguish individual grains. The material forms a compact shard that can be easily disintegrated using a mortar and pestle. Nanomaterials are known to be very reactive, and their properties could change over short periods of time even at room conditions29,32. To minimize this inherent uncertainty, the nanomaterial used in this study came from one batch that went through the same history and was used over the period of ≈1 year. The fact that the microstructural as well as mechanical data are consistent between the individual runs indicates that the starting materials at elevated temperatures and pressures of the experiments have similar properties regardless of the “age” of the starting material.
Sample assembly preparation
For each individual experiment performed, we used ~0.1 g room-dry nanomaterial gouge. This gouge is placed between alumina forcing blocks pre-cut at 45˚, and weld-sealed in a gold jacket of 0.2 mm wall thickness. The jacket was annealed at 900 °C for two hours in advance to make it malleable. Two alumina pistons are placed on the top and bottom of the jacketed sample to transmit the load from the σ1 piston. A 50 mm long graphite furnace around the sample generates heat. Pre-pressed NaCl salt pieces are used as the confining medium. A hole with a diameter of 3.2 mm is drilled in the furnace to place a 2 mm thick alumina ring with inner diameter of 1.5 mm. Another hole with a diameter of 1.6 mm is drilled in the inner salt pieces. A K-type thermocouple goes through these holes and the alumina ring and is directly adjacent to the sample. The sample is oriented to make sure that the thermocouple can measure the temperature in the center of the material. Two 1 mm thick copper discs are placed on the top and bottom of the furnace to allow the current flow through the furnace and heat the sample. The bottom of the assembly is made of a tungsten carbide (WC) plug on which the alumina pistons and inner salt pieces are seated. A pyrophyllite base surrounds the WC plug. Once the sample assembly is placed in the pressure vessel, a piece of lead (Pb) is placed on the top as an upper soft metal disc that transmits the pressure on the sample assembly. See Supplementary Fig. 2 for detailed drawing.
Experimental apparatus
A hydraulically driven Griggs-type apparatus is used to conduct the experiments (see ref. 49 for detailed description of the apparatus). The confining pressure applied to the sample assembly is achieved by compressing the salt inside the pressure vessel with σ3 piston. The salt sleeves transfer the vertical load applied from the σ3 piston into a confining pressure on the sample at the center of the assembly. A differential stress can be applied to the sample with a σ1 piston. Both σ3 and σ1 pistons are controlled by hydraulic rams. The pressure measurements are calculated from the oil pressure within the rams and an external load cell. The temperature of the sample is monitored and controlled by a Eurotherm proportional-integral-derivative (PID) controller connected to the thermocouple.
Experimental procedures and conditions
All experiments were conducted at the same confining pressure of 500 MPa and at temperatures of 200, 300, or 500 °C. The whole experiment consists of three stages: pressurization, deformation, quenching and depressurization. First, during the pressurization, we increase the confining pressure and temperature to experimental conditions in 100 MPa and 100 °C increments. Then, in the second stage, two different boundary conditions are used to study the rheological properties of the samples:
-
Experiments at constant displacement rate
In these experiments, the σ1 pump is driven at a constant oil flow rate to deform the sample until a desired finite shear strain. The flow rate results in an approximately constant displacement rate of the σ1 piston of 10−3 mm s−1.
-
Load-stepping experiments
In these experiments, the samples are deformed at several load steps. Initially, the σ1 piston is driven in at a constant displacement rate until it hits the sample, identically as in the constant displacement rate experiments. After the σ1 piston hits the sample, the load is fixed at each step, until the displacement rate is constant under that load, which indicates that the material is creeping at a steady state (Supplementary Fig. 3).
The last stage of an experiment is quenching and depressurization to bring down the temperature, axial load, and confining pressure to room conditions after deformation. During quenching, the temperature is dropped to the set point (30 °C) automatically and quickly at a rate of 300 °C/min. Simultaneously, the σ1 pump is reversely driven to lower the load until the differential stress, σ1-σ3 ≤ 100 MPa, to minimize unloading cracks. After quenching, both the confining pressure and the load are decreased to room conditions by reducing the oil pressure in the hydraulic rams.
Data acquisition and processing
All the experimental variables (temperature, confining pressure, load, axial and Pc piston position, volts and amps in heating circuit, pressures and flow rates in both syringe pumps) are digitally recorded at a frequency of 1 Hz from the beginning of pressurization. The oil pressure in the hydraulic rams is recorded with an external pressure transducer and used to calculate the confining pressure. The force on the sample is measured by an external load cell. The vertical displacement of σ1 piston is measured by an external displacement transducer with a max. linearity deviation of 0.13%.
The raw mechanical data are corrected for rig stiffness, total “friction” related to the driving in of the σ1 piston into the pressure medium and reducing of contact area between forcing blocks with increasing shear. The stiffness correction accounts for the elastic extension of the machine as load is applied to the sample. Based on the calibration results using an alumina piston, the stiffness of the rig is ~0.0061 mm/kN. “Friction correction” accounts for the internal friction on the ram, the friction on the deformation piston-packing ring, and the friction along different contact surfaces inside the sample assembly. The total friction correction coefficient for the mechanical results in Fig. 1 is 1.31 kN/mm. In addition, an ‘area correction’ accounts for the decreasing overlap as slip increases along the pre-cut forcing blocks.
The general shear geometry implies that there is a pure shear component in the fault rock. The vertical piston displacement can be decomposed into a thinning component perpendicular to the shear zone and a simple shear component along the shear zone. To calculate the shear strain at any given time, we assume that the thinning rate is constant so that the total amount of thinning is evenly distributed during the deformation. The initial thickness before deformation is determined by the experiment 038HS, which we pressurized to 500 MPa and heated to 300 °C and subsequently quenched.
Table 1 summarizes the mechanical results of all the experiments. Using the nanomaterials, experiments 030HS, 028HS, and 034HS were performed at a constant displacement rate ~10−3 mm s−1, corresponding to shear strain rate ~10−3 s−1. Experiments 282MP and 284MP are performed using micropowders at identical conditions30. Two load-stepping experiments (042HS and 064HS) were performed to study the stress-strain rate relationship of the material. Table 1 summarizes the results of the six steps in the experiment at 500 °C (042HS) and eight steps in the experiment at 300 °C (064HS). As we described above, converting measured forces and displacements to stresses and strains involves a number of assumptions (“friction correction”, piston overlap, partitioning of displacement into thinning and shearing components) and therefore higher-strain data points are associated with a larger error.
Microstructural observations
Thin sections are prepared from the samples and the chemical and microstructural properties of the starting as well as deformed materials are investigated in detail via SEM-BSE, optical microscopy, and TEM.
The BSE images are high-resolution compositional maps visualizing the differences in atomic number and density for quickly distinguishing of different phases based on their brightness. For example, phases with greater average atomic number (Z) and/or density show brighter BSE intensity. In contrast, phases with lower average Z and/or density are related to the dark areas. We used a Zeiss Merlin high-resolution scanning electron microscope to obtain the BSE images.
Estimation of the experimental flow law of nanocrystalline fault rocks
The rheological properties of a material can be described in terms of a flow law, which relates shear stress (τ) and shear strain rate (\(\dot{\gamma }\)). In terms of equivalent stress (\(\bar{\sigma }\)) and equivalent strain rate (\(\dot{\bar{\varepsilon }}\)), a flow law has the form of
where \(\bar{\sigma }=\,2\tau ,\) and \(\dot{\bar{\varepsilon }}=\frac{2\surd 3}{3}\dot{\gamma }\). A is the pre-exponential constant; n the stress exponent (~1 for diffusion creep, 2 for dislocation accommodated grain boundary sliding and ~3–5 for dislocation creep50); R, the gas constant; T, absolute temperature; and Q, the activation energy. Notice that the term for grain size dependence in diffusion creep is included in the pre-exponential constant in this formula. This equation can be formulated in terms of logarithms as:
Therefore, the slope of the \(\dot{\bar{\varepsilon }}\) versus \(\bar{\sigma }\) curve in the logarithmic coordinate system returns the stress exponent (n). By fitting the measured points in Table 1 with a linear model and solving the linear least-square problem, we obtain n = 1.8 ± 0.8 at 500 °C, where the error bars indicate a 95% confidence interval. In the same manner, the stress exponent is n = 1.0 ± 0.5 at 300 °C. n ≈ 1 indicates that the nanocrystalline fault rocks deform as a linear-viscous (Newtonian) fluid at 300 °C. A higher stress exponent of n ≈ 2 at 500 °C would be expected if dislocation accommodated grain boundary sliding was the dominant deformation mechanism51. However, our 300 °C experiment is better constrained than the 500 °C experiment (Supplementary Fig. 5).
After obtaining the stress exponent \(n\), we can determine the activation energy using the constant displacement rate experiments at different temperatures by reformulating Eq. (1) as
The slope provides a value for \(Q/{nR}\) and thus determines the activation energy \(Q\) of the material because n is determined independently. The estimated activation energy is \({Q}_{n=1.0}={{{{\mathrm{12,000}}}}}\pm {{{{\mathrm{10,000}}}}}\; {{{{{\rm{J}}}}}}/{{{{{\rm{mol}}}}}}\) and \({Q}_{n=1.8}={{{{\mathrm{21,000}}}}}\pm {{{{\mathrm{18,000}}}}}\;{{{{{\rm{J}}}}}}/{{{{{\rm{mol}}}}}}\) by assuming stress exponents of 1.0 and 1.8, respectively, with the caveat that no steady-state stress level was achieved at low temperatures. As can be seen in Eq. (3), the determination of \(Q\) in the constant displacement rate experiment is not rigorous since the value of the stress exponent n is convolved. Once n and \(Q\) are determined, the pre-exponential constant A can be estimated from the intercept of the \(\dot{\bar{\varepsilon }}\) versus \(\bar{\sigma }\) curve.
The low activation energy estimated from both experiments 042HS and 064HS indicates that the material is temperature insensitive. Thus, we combine both experiments and determine a unified stress component of n = 1.3 ± 0.4 and activation energy of \({Q}_{n=1.3}={{{{\mathrm{16,000}}}}}\pm {{{{\mathrm{14,000}}}}}\;{{{{{\rm{J}}}}}}/{{{{{\rm{mol}}}}}}\) for the material. In this case, a temperature-independent pre-exponential constant A is estimated from the intercept of the \({{\log }}_{10}\bar{\sigma }\;{vs}.\;1/T\) curve with a constant \(\dot{\bar{\varepsilon }}\) of 10−3 s−1.
To verify the estimation of the rheological parameters, we calculate the \(\dot{\bar{\varepsilon }}\) of experiments 030HS, 028HS, and 034HS using the estimated n and \(Q\) and compare them with the experimental values. Supplementary Fig. 4 and Supplementary Table 1 summarize all the calculated \(\dot{\bar{\varepsilon }}\) using different pairs of n and \(Q\). The calculated \(\dot{\bar{\varepsilon }}\) are close to the experimental \(\dot{\bar{\varepsilon }}\,\) of ~1.0 × 10−3 s−1. Therefore, our estimation of the rheological parameters is reasonable.
Sources of error
All the calculations above use a total friction correction coefficient of 1.31 kN/mm. This value is chosen empirically from a large amount of experimental data (see Fig. 2.27 in ref. 52, see also ref. 53). The total friction correction coefficient of the rig cannot be accurately measured, but it affects the estimation of the rheological parameters by changing the value of the measured equivalent stress. Supplementary Fig. 5 shows the evaluation of n and \(Q\) with different friction correction coefficients. With a range of 0.1–2.2 kN/mm, the estimated n and Q range from 0.9 to 1.4 and from 10,000 to 16,000 J/mol, respectively, using data from both experiments (042HS and 064HS).
Calculation of the temperature increase by shear heating
The time-independent temperature increase by shear heating in the nanocrystalline principal slip zone is estimated by solving the steady-state heat equation,
where ρ is the rock density in kg·m−3; Cp, the specific heat capacity in J kg−1 K−1; k, thermal conductivity in W m−1 K−1; T, the temperature in Kelvin (K); and \({Q}_{{sh}}=\dot{\gamma }\cdot \tau\), the heat generation in J m−3 s−1. The equation is solved by the finite-difference method to calculate the steady temperature due to shear heating. The boundary condition is the ambient temperature, T0 that is set to the experimental temperature (200, 300 or 500 °C, see Fig. 5b and Supplementary Fig. 6b, c). Only the thickness (d) of the principal slip zone needs to be known by solving the one-dimensional heat equation. We assume that the heat source is applied to the middle of the shear zone to estimate the largest possible T increase. We also assume that k, ρ, and Cp are constant and let ρ = 2800 kg·m−3, Cp = 1000 J kg−1 K−1, and k = 2.5 W m−1 K−1 (see model parameters for crust in ref. 54). The shear heating result in Supplementary Fig. 6a is calculated using a thickness of 1 mm, which is close to the initial thickness of the shear zone in our experiments. The equivalent shear strain rate, \(\dot{\bar{\varepsilon }}\), is calculated according to the experimental flow law, given \(\bar{\sigma }\) ranging from 100 to 105 MPa and T0 ranging from 100 to 1400 °C. Note that the stress and strain rate in Supplementary Fig. 6a is used to calculate the heat source for shear heating rather than the results after shear heating. Extrapolating the experimental data to a range of conditions that are plausible for fault zones at the base of the seismogenic zone we assume that the thickness of the principal slip zone (d) ranges from 10 μm to 10 cm. The shear velocity, \(v\), applied to the boundary of the shear zone ranges from 10−13 to 101 m/s. Thus, the shear strain rate is given by \(\dot{\gamma }=v/d\) and plotted in Fig. 5b and Supplementary Fig. 6b, c. Then the equivalent stress before shear heating can be calculated by the experimental flow law. This equivalent stress for the source of shear heating is not plotted in Fig. 5b and Supplementary Fig. 6b, c. Instead, we plot the contours of the equivalent stresses after accounting for the effect of shear heating.
Data availability
Source data are provided with this paper. All mechanical data are available on zenodo.org at https://doi.org/10.5281/zenodo.5496000.
Code availability
Codes for the mechanical data evaluation results in Figs. 1 and 5, and Supplementary Figs. 3–6 can be accessed at https://doi.org/10.5281/zenodo.5496000.
References
Faulkner, D. R. et al. A review of recent developments concerning the structure, mechanics and fluid flow properties of fault zones. J. Struct. Geol. 32, 1557–1575 (2010).
Bürgmann, R. The geophysics, geology and mechanics of slow fault slip. Earth Planet. Sci. Lett. 495, 112–134 (2018).
Badt, N. Z., Tullis, T. E., Hirth, G. & Goldsby, D. L. Thermal pressurization weakening in laboratory experiments. J. Geophys. Res. Solid Earth 125, e2019JB018872 (2020).
Noda, H. & Lapusta, N. Three‐dimensional earthquake sequence simulations with evolving temperature and pore pressure due to shear heating: Effect of heterogeneous hydraulic diffusivity. J. Geophys. Res. Solid Earth 115, B12314 (2010).
Rice, J. R. Heating and weakening of faults during earthquake slip. J. Geophys. Res. Solid Earth 111, B05311 (2006).
Kelemen, P. B. & Hirth, G. A periodic shear-heating mechanism for intermediate-depth earthquakes in the mantle. Nature 446, 787–790 (2007).
Marone, C. Laboratory-derived friction laws and their application to seismic faulting. Annu. Rev. Earth Planet. Sci. 26, 643–696 (1998).
Sammis, C. G. & Ben‐Zion, Y. Mechanics of grain‐size reduction in fault zones. J. Geophys. Res. Solid Earth 113, B02306 (2008).
Brantut, N., Sulem, J. & Schubnel, A. Effect of dehydration reactions on earthquake nucleation: Stable sliding, slow transients, and unstable slip. J. Geophys. Res. Solid Earth 116, B05304 (2011).
Ferrand, T. P. et al. Dehydration-driven stress transfer triggers intermediate-depth earthquakes. Nat. Commun. 8, 1–11 (2017).
Okazaki, K. & Hirth, G. Dehydration of lawsonite could directly trigger earthquakes in subducting oceanic crust. Nature 530, 81–84 (2016).
Pec, M., Stünitz, H., Heilbronner, R., Drury, M. & de Capitani, C. Origin of pseudotachylites in slow creep experiments. Earth Planet. Sci. Lett. 355–356, 299–310 (2012).
Proctor, B. P., Lockner, D. A., Lowenstern, J. B. & Beeler, N. M. Conversion of wet glass to melt at lower seismogenic zone conditions: implications for pseudotachylyte creep. Geophys. Res. Lett. 44, 10–248 (2017).
Green, H. W. II et al. transformation and nanometric flow cause extreme weakening during fault slip. Nat. Geosci. 8, 484–489 (2015).
Schubnel, A. et al. Deep-focus earthquake analogs recorded at high pressure and temperature in the laboratory. Science 341, 1377–1380 (2013).
Hayward, K. S. et al. Mechanical amorphization, flash heating, and frictional melting: dramatic changes to fault surfaces during the first millisecond of earthquake slip. Geology 44, 1043–1046 (2016).
Passelègue, F. X., Schubnel, A., Nielsen, S., Bhat, H. S. & Madariaga, R. From sub-Rayleigh to supershear ruptures during stick-slip experiments on crustal rocks. Science 340, 1208–1211 (2013).
Di Toro, G. et al. Fault lubrication during earthquakes. Nature 471, 494–498 (2011).
Siman-Tov, S., Aharonov, E., Sagy, A. & Emmanuel, S. Nanograins form carbonate fault mirrors. Geology 41, 703–706 (2013).
Kirkpatrick, J. D., Rowe, C. D., White, J. C. & Brodsky, E. E. Silica gel formation during fault slip: evidence from the rock record. Geology 41, 1015–1018 (2013).
Ault, A. K., Jensen, J. L., McDermott, R. G., Shen, F.-A., & Van Devener, B. R. Nanoscale evidence for temperature-induced transient rheology and postseismic fault healing. Geology 47, 1203–1207 (2019).
Marti, S., Stünitz, H., Heilbronner, R. & Plümper, O. Amorphous material in experimentally deformed mafic rock and its temperature dependence: Implications for fault rheology during aseismic creep and seismic rupture. J. Struct. Geol. 138, 104081 (2020).
Hadizadeh, J., Tullis, T. E., White, J. C. & Konkachbaev, A. I. Shear localization, velocity weakening behavior, and development of cataclastic foliation in experimental granite gouge. J. Struct. Geol. 71, 86–99 (2015).
Pec, M. & Al Nasser, S. Formation of Nanocrystalline and amorphous materials causes parallel brittle‐viscous flow of crustal rocks: experiments on Quartz–Feldspar aggregates. J. Geophys. Res. Solid Earth 126, e2020JB021262 (2021).
Rowe, C. D. et al. Earthquake lubrication and healing explained by amorphous nanosilica. Nat. Commun. 10, 1–11 (2019).
Verberne, B. A., Plümper, O., de Winter, D. A. M. & Spiers, C. J. Superplastic nanofibrous slip zones control seismogenic fault friction. Science 346, 1342–1344 (2014).
Verberne, B. A., Plümper, O. & Spiers, C. J. Nanocrystalline principal slip zones and their role in controlling crustal fault rheology. Minerals 9, 328 (2019).
Meyers, M. A., Mishra, A. & Benson, D. J. Mechanical properties of nanocrystalline materials. Prog. Mater. Sci. 51, 427–556 (2006).
Yund, R. A., Blanpied, M. L., Tullis, T. E. & Weeks, J. D. Amorphous material in high strain experimental fault gouges. J. Geophys. Res. 95, 15589–15602 (1990).
Pec, M., Stünitz, H., Heilbronner, R. & Drury, M. Semi-brittle flow of granitoid fault rocks in experiments. J. Geophys. Res. Solid Earth 121, 1677–1705 (2016).
Pec, M., Stünitz, H. & Heilbronner, R. Semi-brittle deformation of granitoid gouges in shear experiments at elevated pressures and temperatures. J. Struct. Geol. 38, 200–221 (2012).
Reches, Z. & Lockner, D. A. Fault weakening and earthquake instability by powder lubrication. Nature 467, 452–455 (2010).
Hirose, T. & Shimamoto, T. Growth of molten zone as a mechanism of slip weakening of simulated faults in gabbro during frictional melting. J. Geophys. Res. 110, B05202 (2005).
Niemeijer, A. et al. Inferring earthquake physics and chemistry using an integrated field and laboratory approach. J. Struct. Geol. (2012).
Han, R., Hirose, T., Shimamoto, T., Lee, Y. & Ando, J. Granular nanoparticles lubricate faults during seismic slip. Geology 39, 599–602 (2011).
Brace, W. F. & Byerlee, J. D. Stick-slip as a mechanism for earthquakes. Science 153, 990–992 (1966).
Raj, R. & Ashby, M. F. On grain boundary sliding and diffusional creep. Metall. Trans. 2, 1113–1127 (1971).
Sun, C. Q. Size dependence of nanostructures: Impact of bond order deficiency. Prog. Solid State Chem. 35, 1–159 (2007).
Shukla, S., Seal, S., Vij, R. & Bandyopadhyay, S. Reduced activation energy for grain growth in nanocrystalline yttria-stabilized zirconia. Nano Lett. 3, 397–401 (2003).
Verberne, B. A. et al. Nanocrystalline slip zones in calcite fault gouge show intense crystallographic preferred orientation: crystal plasticity at sub-seismic slip rates at 18–150 C. Geology 41, 863–866 (2013).
Verberne, B. A. et al. Microscale cavitation as a mechanism for nucleating earthquakes at the base of the seismogenic zone. Nat. Commun. 8, 1–8 (2017).
Kikuta, H., Toyota, H. & Yu, W. Optical elements with subwavelength structured surfaces. Opt. Rev. 10, 63–73 (2003).
Scholz, C. H. Earthquakes and friction laws. Nature 391, 37–42 (1998).
Braeck, S. & Podladchikov, Y. Y. Spontaneous thermal runaway as an ultimate failure mechanism of materials. Phys. Rev. Lett. 98, 95504 (2007).
Kaneki, S., Oohashi, K., Hirono, T. & Noda, H. Mechanical amorphization of synthetic fault gouges during rotary‐shear friction experiments at subseismic to seismic slip velocities. J. Geophys. Res. Solid Earth 125, e2020JB019956 (2020).
Burnley, P. C., Green, H. W. II & Prior, D. J. Faulting associated with the olivine to spinel transformation in Mg2GeO4 and its implications for deep-focus earthquakes. J. Geophys. Res. Solid Earth 96, 425–443 (1991).
Green, H. W. Shearing instabilities accompanying high-pressure phase transformations and the mechanics of deep earthquakes. Proc. Natl Acad. Sci. USA 104, 9133–9138 (2007).
Wilson, B., Dewers, T., Reches, Z. & Brune, J. Particle size and energetics of gouge from earthquake rupture zones. Nature 434, 749–752 (2005).
Ghaffari, H. O. & Pec, M. An ultrasound probe array for a high-pressure, high-temperature solid medium deformation apparatus. Rev. Sci. Instrum. 91.8, 085117 (2020).
Kohlstedt, D. L. & Hansen, L. N. Treatise on Geophysics. (Elsevier, 2015).
Hansen, L. N., Zimmerman, M. E. & David, L. Kohlstedt. Grain boundary sliding in San Carlos olivine: flow law parameters and crystallographic‐preferred orientation. J. Geophys. Res. Solid Earth 116, B08201 (2011).
Peč. Experimental investigation on the rheology of fault rocks. (Diss. University of Basel, 2014).
Heilbronner, R., Stunitz, H., Précigout, J. & Raimbourg, H. The solid medium deformation apparatus–reloaded. in EGU General Assembly Conference Abstracts 9859 (2020).
Devès, M. H., Tait, S. R., King, G. C. & Grandin, R. Strain heating in process zones; implications for metamorphism and partial melting in the lithosphere. Earth Planet. Sci. Lett. 394, 216–228 (2014).
Acknowledgements
Holger Stünitz and Oliver Jagoutz are gratefully acknowledged for copy-editing of an earlier version of this manuscript. Shiahn Chen and Yong Zhang are thanked for assistance with FIB and TEM imaging. Funding by NSF EAR-1833478 & EAR-2054414 for laboratory technician support are gratefully acknowledged. This work made use of the MRSEC Shared Experimental Facilities at MIT, supported by the National Science Foundation under award number DMR-1419807. H.S. was supported by MIT Earth Resources Laboratory and MIT MathWorks Science Fellowship. Funding for the article-processing charge was partially supplied by the MIT Libraries.
Author information
Authors and Affiliations
Contributions
H.S. performed the experiments on nanocrystalline rocks, evaluated the mechanical and microstructural data. M.P. designed the study, performed the experiments on microcrystalline rocks, and performed quantitative image analysis. Both authors participated in the interpretation of the data and co-wrote the text.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Peer-review information Nature Communications thanks the anonymous reviewer(s) for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sun, H., Pec, M. Nanometric flow and earthquake instability. Nat Commun 12, 6779 (2021). https://doi.org/10.1038/s41467-021-26996-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-021-26996-0
- Springer Nature Limited