Abstract
Over the past years, metasurfaces have been of great interest due to their ability manipulate optical wavefront by introducing a phase gradient across the transverse directions of the wave. This phase gradient was usually realized using plasmonic resonators which had high intrinsic losses. Here, we demonstrate, numerically, a proof of principle of an all-dielectric silicon based metasurface at the infrared (IR) range that manipulates the wave front and achieves beam steering with significantly high transmission. The proposed cross-shaped unit cell design shows high transmission with the ability to fully control the phase of the transmitted wave from 0 to 2π. The metasurface is made of silicon cross resonators, arranged to have a linear phase gradient, on SiO2 substrate which makes the device compatible with most standard semiconductor fabrication techniques.
Similar content being viewed by others
Introduction
Metasurfaces are planar (or semi-planar) structures based on a periodic or quasi periodic two-dimensional array of cells. Arranging these cells in a certain manner can be used to manipulate certain properties of light1,2,3,4. Conventional devices controlled the light wave by accumulating phase through propagating through a certain medium. In metasurfaces however, each unit cell conveys a discrete phase change for the incident light1. Through the proper design of the unit cells we can control different properties of the light wave such as amplitude, phase and polarization. Many structures have been proposed to demonstrate wide range of applications for metasurfaces, such as lenses5,6, focusing mirrors7, and holograms8. Metasurfaces were engineered based on metal planar structures, which have significantly high intrinsic losses that lead associated low transmission limiting their practical applications1,6,7,9,10,11. On the other hand, all-dielectric resonant metasurfaces have negligible absorption losses12,13. For most of the proposed designs, all-dielectric metasurfaces demonstrate superior performances in terms of transmission and control over both polarization and phase gradient across the interface. These structures are mostly operating at visible, near-IR or telecom frequencies7,14,15,16,17,18. However, applications of metasurfaces at longer IR wavelengths have a lot of potential19,20. The IR is range of great interest for a variety of applications, as the thermal signatures of most objects exist in this range. Hence, it can be used for sensing applications. In addition, it is also essential for thermal imaging and energy harvesting21. There have been numerous efforts for designing IR beam-steering metasurfaces16,22. However, it is still challenging to handle two different polarizations, that are normal to each other, simultaneously to achieve polarization independence. In this work, a polarization-independent unit cell is developed and utilized within an all-dielectric metasurfaces that is CMOS compatible. This new design can achieve beam steering with normalized transmission as high as 0.89 for x-polarized field and 0.81 for y-polarized light. This design can be tailored to achieve different steering angles by simply changing the periodicity of the structure.
Methods and Results
To achieve polarization independence, the unit cell must be symmetric in the transverse directions. Additionally, this unit cell should exhibit both electric and magnetic resonances in the vicinity of each other around the operation wavelength (λo). This would allow us to fully control the phase of the transmitted wave over the range from 0 ° to 360o. A cross-shaped unit cell is chosen to achieve the previously mentioned design constraints (Fig. 1). Choosing the design parameters to be the length (a) and width (b) of the cross will maintain the symmetry in the transverse direction. This cross is made of silicon with refractive index of 3.67 on a SiO2 substrate of refractive index 1.4522. Height (h) of 560 nm was found to be sufficient to manipulate both electric and magnetic resonances for the operation wavelength (λo) of 3.1 µm. This is achieved using periodicity (w) of 1.6 µm. This satisfies the condition of the unit cell being less than half the operation wavelength.
Finite difference time domain (FDTD) simulations have been used to study the behavior of the previously mentioned structure. A unit cell having of a = 1.3 µm and b = 0.9 µm was used to check the resonance effect discussed previously. A y-polarized plane wave is injected in the z-direction and the transmission spectrum is studied. Two resonance peaks can be seen in Fig. 2b, one at 3.46 µm and the other at 3.18 µm. At 3.46 µm, the electric field in the y-z plane resembles that of a dipole and the magnetic field in the x-z plane has a vortex like shape and vice versa at 3.18 µm (Fig. 2a). This verifies that the resonance at 3.46 µm is indeed electric resonance while at 3.18 µm is magnetic resonance.
Next, a sweep over the design parameters a and b has been performed to find the phase and transmission corresponding to each dimension of a and b. This gives us a clear map for the required dimensions to achieve a specific transmission and its corresponding phase (Fig. 3). This can be used in different applications like beam steering or lensing.
To achieve beam steering, we can divide the entire phase range into seven segments having 51° increment to the phase. In our case we approximated this to 50° increment (i.e. 0, 50, 100, 150, 200, 250, 300) with a = 1.38, 1.08, 0.28, 0.8, 1.04, 1.34, 1.4 µm and b = 0.56, 0.97, 0.28, 0.3, 0.38, 0.42, 0.5 µm. This creates a phase gradient along one of the transverse directions (in our case we chose this to be the y-direction). This gradient introduces an extra term to Snell’s law as follows1:
where ni and ns are the refractive indices in the background material and substrate respectively. θs and θi are the angles of transmission and incidence, and \(\frac{d{\rm{\Phi }}}{dx}\) is the phase gradient along x. In our case ni is 1 for air and ns is 1.45 for SiO2. Using this equation at the first interface and the normal Snell’s law at the other interface between the substrate and air we can deduce that for a ray incident normally on the metasurface then propagating through the substrate to air again the angle of transmission will follow the equation22:
where θt is the transmission angle, nt is the refractive index of air, and Γ is the periodicity of the structure in the direction where there is a phase gradient, which is the y-direction in our case (Fig. 4). From this we can expect θt to be about 16°.
A plane wave is injected on the metasurface in the z-direction. Both polarizations have been simulated to ensure polarization independence. Note that although the unit cell is symmetric, the beam steering structure itself is not symmetric in x and y. It is expected to see small difference between the x and y-polarized fields (Fig. 5a–d). In the case of y-polarization the normalized transmission was found to be 0.8 and the wave fronts were more regular than that found in the x-polarized field. However, when using y-polarized field the transmission is 0.89 which is the greatest beam steering efficiency achieved to date according to our knowledge.
The beam steering angle can be changed by simply manipulating Γ. This is done by increasing the unit cell dimension to Γ = 12.6 µm. This successfully changed the angle to 14.3° which is expected from Eq. (2) (Fig. 5e–h). However, the transmission was reduced to 0.53 this was due to the change of the periodicity of each cross from the initial design (i.e. from 1.6 to 1.8 µm).
The operation bandwidth is defined as the range of wavelengths where beam steering effect still occur with change of the transmission ±10% and the angle doesn’t deviate ±5° from the design steering angle that can obtained for each wavelength from Eq. (2). It was found that the device can have an operation bandwidth ranging from 2.96 µm to 3.2 µm. At 2.96 µm the steering angle is 12° which is less than the design angle for this wavelength found from Eq. (2) only by 3.32° (Fig. 6b). At 3.2 µm the steering angle is 17.5° which is more than the design angle for this wavelength found from Eq. (2) only by 0.9° (Fig. 6c). Although the transmission is still relatively high outside the operation bandwidth (Fig. 6a), the wave front starts to distort and the steering function is compromised.
We also show that this structure can support scalability. We scale the structure to have a smaller height (h = 220 nm) so the structure can be fabricated using standard Silicon-on-Insulator (SOI) fabrication procedure. This required that the dimensions of the whole structure be multiplied by 0.393, which is the ratio between the old and new heights. The structure works in the near-infrared domain with operation wavelength of 1.218 µm. Figure 7(a–d) shows that similar beam steering effect has been simulated for different x and y-polarized plane waves, with steering angle of 16.4°. While changing the periodicity (w) to be 0.733 µm instead of 0.65 µm decreases the steering angle to 14.3° (Fig. 7e–h). This scaling of the height shows the flexibility of the design to different wavelengths.
Conclusion
A new polarization-independent unit cell design was developed for all-dielectric metasurfaces that can be CMOS compatible. This new design can achieve beam steering with the highest efficiency to date of 0.89 for x-polarized field and 0.81 for y-polarized light. This design can be tailored to achieve different steering angles by changing the periodicity of the structure. The operation bandwidth was studied and found to be narrow from 2.96 µm to 3.215 µm.
Data Availability
All data needed to evaluate the conclusions in the paper are present in the paper.
References
Yu, N. et al. Light Propagation with Phase Discontinuities Reflection and Refraction. Science (80-.) 334, 333–337 (2011).
Sun, S. et al. Gradient-index meta-surfaces as a bridge linking propagating waves and surface waves. Nat. Mater. 11, 426–431 (2012).
Zheludev, N. I. & Kivshar, Y. S. From metamaterials to metadevices. Nat. Mater. 11, 917–924 (2012).
Kildishev, A. V., Boltasseva, A. & Shalaev, V. M. Planar photonics with metasurfaces. Science 339, 1232009 (2013).
Byrnes, S. J., Lenef, A., Aieta, F. & Capasso, F. Designing large, high-efficiency, high-numerical-aperture, transmissive meta-lenses for visible light. Opt. Express 24, 5110–5124 (2016).
Wang, W. et al. Plasmonics metalens independent from the incident polarizations. Opt. Express 23, 16782–16791 (2015).
Pors, A., Nielsen, M. G., Eriksen, R. L. & Bozhevolnyi, S. I. Broadband Focusing Flat Mirrors Based on Plasmonic Gradient Metasurfaces. Nano Lett. 13, 829–834 (2013).
Devlin, R. C., Khorasaninejad, M., Ting, W., Oh, J. & Capasso, F. Broadband high-efficiency dielectric metasurfaces for the visible spectrum. Proc. Natl. Acad. Sci. 113, 10473–10478 (2016).
Luo, J. et al. Tight focusing of radially and azimuthally polarized light with plasmonic metalens. Opt. Commun. 356, 445–450 (2015).
Wang, W. et al. Polarization-independent longitudinal multi-focusing metalens. Opt. Express 23, 29855 (2015).
Tassin, P., Koschny, T., Kafesaki, M. & Soukoulis, C. M. A comparison of graphene, superconductors and metals as conductors for metamaterials and plasmonics. Nat. Photonics 6, 259–264 (2012).
Ahmadi, A. & Mosallaei, H. Physical configuration and performance modeling of all-dielectric metamaterials. Phys. Rev. B 77, 045104 (2008).
Dharmavarapu, R., Ng, S. H., Bhattacharya, S. & Juodkazis, S. All-dielectric metasurface for wavefront control at terahertz frequencies. in Nanophotonics Australasia 2017 (eds Chon, J. W. M. & Jia, B.) 104561, 61 (SPIE, 2018).
Khorasaninejad, M. et al. Metalenses at visible wavelengths: Diffraction-limited focusing and subwavelength resolution imaging. Science 352, 1190–4 (2016).
Khorasaninejad, M. et al. Achromatic Metasurface Lens at Telecommunication Wavelengths. Nano Lett. 15, 5358–5362 (2015).
Cheng, J., Ansari-Oghol-Beig, D. & Mosallaei, H. Wave manipulation with designer dielectric metasurfaces. Opt Lett 39, 6285–6288 (2014).
Aoni, R. A. et al. High-Efficiency Visible Light Manipulation Using Dielectric Metasurfaces. Sci. Rep 9, 6510 (2019).
Sun, M. et al. Efficient visible light modulation based on electrically tunable all dielectric metasurfaces embedded in thin-layer nematic liquid crystals. Sci. Rep 9, 8673 (2019).
Guo, Z., Tian, L., Shen, F., Zhou, H. & Guo, K. Mid-infrared polarization devices based on the double-phase modulating dielectric metasurface. J. Phys. D. Appl. Phys. 50, 254001 (2017).
La Spada, L. Metasurfaces for Advanced Sensing and Diagnostics. Sensors (Basel) 19, 355 (2019).
Wu, C. et al. Metamaterial-based integrated plasmonic absorber/emitter for solar thermo-photovoltaic systems. J. Opt. 14, 024005 (2012).
Shalaev, M. I. et al. High-Efficiency All-Dielectric Metasurfaces for Ultracompact Beam Manipulation in Transmission Mode. Nano Lett. 15, 6261–6266 (2015).
Author information
Authors and Affiliations
Contributions
M. Swillam suggested and supervised the project. M.A. has performed the theoretical modeling and numerical simulations. A.M.M. and M. Swillam revised the results and the analysis. All authors discussed and edited the manuscript.
Corresponding authors
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Abdelsalam, M., Mahmoud, A.M. & Swillam, M.A. Polarization independent dielectric metasurface for infrared beam steering applications. Sci Rep 9, 10824 (2019). https://doi.org/10.1038/s41598-019-47097-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-019-47097-5
- Springer Nature Limited
This article is cited by
-
Voice interactive information metasurface system for simultaneous wireless information transmission and power transfer
npj Nanophotonics (2024)
-
Verification of a metamaterial with gradient particles and its near-field radiative heat transfer property
Optical and Quantum Electronics (2024)
-
Cost-Effective and Environmentally Friendly Mass Manufacturing of Optical Metasurfaces Towards Practical Applications and Commercialization
International Journal of Precision Engineering and Manufacturing-Green Technology (2024)
-
Verification of the Effect of Local Electric Field Resonance Behaviors on the Transmission Properties of the Dual-Band Terahertz Metasurface
Journal of Electronic Materials (2023)