Abstract
The composite attachment loss during orthodontic clear aligner therapy is an adverse event that commonly happens in clinical practice and can affect the overall outcome and length of treatment. The aim of our research is to provide a basis for the further study of an innovative digital protocol and application method for orthodontic aligner attachments. Two 3D models were designed, one based on the proposed protocol and the other on the conventional method for aligner attachment application. Four attachment shapes were used to identify the maximum values for the von Mises equivalent stresses, the maximum displacements values and the areas in which these values were recorded through FEM analysis. The results of the mechanical simulation show lower values of von Mises stress recorded in the 3D printed attachments assemblies, independent of their shape, when simulated under the same boundary and load conditions. The trapezoidal prism shaped 3D printed model has a 3.7 times smaller displacement value (0.088 [mm]) compared to the adhesive resin model (0.326 [mm]). In conclusion, the proposed protocol for aligner attachments and the introduction of innovative materials is a promising method of solving conventional attachment problems in current orthodontic treatments.
Similar content being viewed by others
Introduction
In modern orthodontics, due to an increased demand for aesthetics and health, orthodontic clear aligner treatments have gained popularity among adult and adolescent patients1. This type of treatment requires digitally designed attachments, made of polymeric resins2,3,4, applied on the enamel surface that maximize the contacts between the trays and the teeth, providing the orthodontic force and improving the retention of the aligner5,6.
The research directions in the field, at present, are focused on determining the forms and dimensions of clinically effective attachments7,8,9,10, the development of new materials11,12,13 and application methods14,15, reducing attachment loss during treatment16,17 and increased stability18,19.
Accurate application of attachments in the treatment with braces and their resistance is crucial to obtain the desired tooth movement15. The same principles apply to orthodontic aligner attachments, although conventional bonding procedures which use thermoformed templates, lack precision and often create resin overflows, producing excess on the enamel surface20. Therefore, after the debonding of brackets the volume and surface of remnant adhesive is smaller compared to the removal of multiple composite aligner attachments in the final stages of contemporary aligner treatment21. It is also important that this transfer process results in a precise reproduction of the digital attachment's shape and dimension to ensure a proper fit of aligners14.
The aim of our research is to simulate and test the mechanical behavior and proprieties of orthodontic aligner attachments obtained using an innovative protocol, comprising of CAD design, 3D printing and adhesive application, thus broadening the scope of biomaterials used in the production of these attachments and improving the shortcomings of conventional protocols used in current aligner treatments.
Materials and methods
Proposed protocol for 3D printed orthodontic aligner attachments
In the proposed protocol the aligner attachments were bonded to the tooth surface by a 200 [μm] thick layer of adhesive flowable resin, as opposed to the conventional technique in which the whole attachment would be constructed out of the afore mentioned flowable resin. Models of a central upper incisor, four attachments of various commonly used shapes (semi-ellipsoid, semi-sphere, cuboid, trapezoidal prism) and the adhesive resin between them were 3D modeled.
The 3D models were assembled to reproduce the vestibular attachments used in aligner orthodontic treatment for both protocols: 3D printed attachment bonded with adhesive on the tooth surface and attachment fully consisting of adhesive composite resin (Fig. 1).
The geometrical dimensions of the shapes used were: semi-ellipsoid (major radius 1.5 [mm] and minor radius 1 [mm]); semi-sphere (radius 1 [mm]); trapezoidal prism (2 mm by 4 mm base with a 400 [μm] extrusion at the top and a 1 [mm] extrusion at the bottom); cuboid shape (2 [mm] sided square extruded 1 [mm]) (Fig. 2).
Finite element analysis of proposed 3D printed versus conventional attachments
Using Abaqus FEA (Dassault Systems, France) analysis software, a series of simplified incisor-adhesive-attachment assemblies were modeled and used in the FEM simulations. The adhesive layer between the enamel and the dental attachments has a thickness of 200 [μm]22 that extends over the entire contact surface between the tooth vestibular surface and the 3D printed attachment.
Instead of using the whole 3D model of the incisor, a 4 [mm] by 8 [mm] with a 1 [mm] extrusion partition was used, proper boundary conditions were applied in order to simulate the whole incisor tooth. The simplified 3D models are presented in Fig. 3.
A series of three materials were defined (Table 1). NextDent C&B Micro Filled Hybrid, which is a biocompatible Class II-a, photopolymerizable, 3D printable material developed for crowns and bridges by “Next Dent” (Vertex-Dental, Netherlands), has the following mechanical properties: an uniformly distributed density ρ = 1.15E − 009, an compression modulus E = 2200 [MPa] and a Poisson’s ratio of ν = 0.3. All values were taken from existing literature23,24. For the adhesive material, the mechanical properties provided by the manufacturer in the 3 M™ ESPE™ Filtek™ “Supreme XT Flowable Restorative” (Flow) technical product profile22, were used. These consisted of an uniformly distributed density of ρ = 1.84E − 009, compression modulus E = 380 [MPa] and a Poisson’s ratio of ν = 0.3. For the mechanical properties of the tooth model, enamel mechanical properties found in literature8,14 were used respectively, density ρ = 3.1E − 009, compression modulus E = 19,613.3 [MPa], Poisson’s ratio ν = 0.15.
Two simulations (proposed protocol and conventional protocol) were undergone for each attachment shape, using two different intensities for the applied loads in order to reproduce different exploitation conditions for the aligner attachments. This lead to a total of 16 simulations for the 4 studied attachment shapes: semi-ellipsoid; semi-sphere; trapezoidal-prism; cuboid.
The models were meshed using an approximate global seed size of 0.2 using “Tet” shaped elements (Fig. 4a). The loads and boundary conditions are presented in Fig. 4b. On the top and posterior surfaces of the simplified tooth 3D model, an “Encastre” boundary condition was set in order to simulate the rest of the incisor body.
From the wide variety of forces that occur during aligner treatment, the chosen type of force used in the simulations was an positive uniformly distributed pressure, one round of simulations used a magnitude of 50 [N] and another round of simulations used a similar type of load, this time, with a magnitude of 10 [N]. They were applied on the lower half of the orthodontic aligner attachments used in the simulations. During aligner treatment, besides the fact that different types of forces can occur, they can be applied from different directions, if not successively from all directions throughout the orthodontic treatement. The chosen direction of the applied pressure was upwards in order to reproduce the maximum load scenario used in simulations (50 [N]).
After the material, load and constraint parameters where set, a job was created for each of the eight instances using Abaqus’s Job Manager (Dassault Systems, France).
Results
Simulations based on the 3D printed models, models that were assigned three different material properties: enamel—adhesive resin—3D printed resin (proposed protocol), the FEM analysis highlights the maximum values for: the von Mises equivalent stresses, the maximum displacements values and the areas in which these values were recorded in Fig. 5. FEM analysis results for the convetional protocol simulations (orthodontic aligner attachments modeled using the same material properties as the flowable adhesive resin) simulation are presented in Fig. 6.
The maximum values obtained for each attachment design, simulated using both the conventional attachment protocol and the bonded 3D printed attachment protocol are presented in Table 2.
The graphical representations of the results for the von Mises stress and the displacement values for each simulations are shown in Fig. 7.
Discussions
Attachments are mainly used for two purposes: increasing the retention of aligners and supporting movements that occur during their application and general usage. Considering that all aligners are produced based on the attachments, which are usually bonded using initial templates, errors in initial bonding will generate unplanned tooth movements14. Regardless of the template thickness/material or the composite viscosity, this conventional technique presents some faults: the amount of composite necessary for attachment fabrication is not predetermined, the presence of resin overflow around the attachments20. Also, the precision of the attachment can only be checked after light curing and bonding on the enamel surface13. The proposed protocol considered in the present research addresses the precision and overflow problem by using previously 3D printed aligner attachments which are bonded to the enamel surface similar to classic fixed braces. Therefore, there would be an increase in attachment precision and a decrease in the amount of composite excess, that would require further refinement with burs and cause damage to the enamel surface.
The consistency, viscosity and other composite properties can influence the position and shape of attachments, factors that are essential for the efficacy of the attachments5. The 3D printable resin used to create the proposed protocol simulation models has greater mechanical proprieties than the conventional flowable composite resins used in aligner treatment.
Studies suggest that higher bonding forces lead to superior retention of the attachments25. The Finite Element Method numerical technique used to analyze the proposed method of 3D printed aligner attachments versus the conventional method is widely used in the orthodontic field to analyze the stress strain distribution of orthodontic appliances5,26 and has long been validated as a tool that provides acceptable accuracy to predict clinical outcomes7. Given the small contact area analized and identical simulation environments, the present study uses simplified models in FEM simulations27, the aim being to reduce the number of nodes and the overall output time of the analysis. The lack of a curvature between the simplified models contact surfaces is a limitation of the current study and could be adressed in future research.
Another limitation can be the fact that the simplified models used in the current research were only partitioned into separate regions on which different material properties were set, thus highlight the mechanical behavior of an ideal model without taking into consideration the adhesive properties between them. Literature sugests that 3D printed composite resin behaves similarly to other well-established definitive restoration materials28. Given the lack of studies on 3D printed attachments, the analisis of the adhesion between flowable and 3D printed resins represent a topic that can be explored in future research papers.
Forces used in this study were based on literature that suggested that distributed forces up to a maximum value of 10[N] cand be exerted by orthodontic aligners on attachments29, loads that are further distributed onto the tooth surface. Also, a value equivalent to the maximum force that could be exercited by the hand of a human operator in case of improper maneuvering30, during the application of the orthodontic aligner or attachment, was used in simulations. The direction of the loads was chosen to be vertical, in order to be consistent with the highest value of 50 [N], used in the current study.
The results of the mechanical simulation show lower values of von Mises stress in the case of the 3D printed attachments assemblies, independent of their shape or applied pressure, when simulated under the same boundary and load conditions. The semi-ellipsoid model made out of the 3D printed resin registered a sensibly lower von Mises stress (48.577 [MPa]) compared to the conventional attachment made out of the flowable resin (50.859 [MPa]), when the load of 50 [N] was applied. For the 10 [N] simulation, similar differences were registered. Maximum values of 9.652 [MPa] for the 3D printed model and 10.332 [MPa] for the attachment model that was assigned flowable adhesive resin mechanical properties. The semi-sphere 3D printable resin model also obtained better results (109.108 [MPa]) compared to the conventional attachment model (110.811 [MPa]) when a load of 50 [N] was applied. In the 10 [N] load simulation, a maximum of 22.703 [MPa] was registered, compared to the value of 25.164 [MPa] obtained in the flow resin model.
Higher differences between results were observed in the case of the trapezoidal prism, 68.742 [MPa] for the 3D printed material compared with 103.193 [MPa] for the conventional attachment at 50 [N], and a maximum of 13.821 [MPa] in the 10 [N] load simulation, compared to the value of 24.149 [MPa] obtained for the conventional adhesive attachment. The cuboid shaped attachment registered a maximum value of 106.358 [MPa] in the case of the 3D printable resin, compared to 133.953 [MPa] registered for the adhesive resin model at a load of 50 [N]. When subjected to a load of 10 [N], the maximum von Mises stresses were 21.658 [MPa] in the 3D printed model simulation and 29.864 [MPa] in the case of the flow adhesive model.
In orthodontics, when using bonded metallic brackets, the main failure point is the adhesive layer level15. While the results of the present study show the same general behavior (the location of the maximum von Mises stresses occur at the bonding layer), in the case of the 3D printed resin attachment-adhesive-enamel model, the bonded 3D printed attachment can withstand higher forces than the currently used technique for transferring aligner attachments, therefore limiting the loss of the attachments. Loss that has been reported to be an issue for both clinicians and patients alike17,21. Studies showing increased incidence of composite attachment loss during orthodontic clear aligner therapy, with a loss rate in molar attachments at up to 11.49%, higher than at the incisor level with almost 6%31.
Regarding adhesive resins losses, no significant differences in the survival rates were observed while studying the failure rate of multiple flowable composites32. Therefore, the proposed protocol in which we use flowable composite resin for adhesion to the enamel surface, due to the small size of the aligner attachments, should not result in greater loss rates than classic orthodontic brackets. The resistance to higher stresses of the 3D printed attachment allows the use of larger attachments, greater size offering the possibility of a continuous increase in force and momentum33, thus increasing the level of retention of the aligner and facilitating a better force transition in the favor of orthodontic tooth movements.
The displacement values resulted from the simulations are around 2.767 times lower in the case of the semi-ellipsoid model made out of the 3D printed resin (0.043 [mm]) than in the case of the bonding resin model (0.119 [mm]) under an applied pressure of 50 [N]. When subjected to the 10 [N]] load, the 3D printed model registered a displacement of 0.009 [mm] (2.777 times lower) while the flow model registered a 0.025 [mm]. A displacement value of 2.323 times smaller was registered in the case of the semi-sphere 3D printable resin model (0.071 [mm]) compared to the adhesive resin model (0.165 [mm]) in the 50 [N] simulation. While simulating under the load of 10 [N], the 3D model registered a displacement value of 0.014 [mm] compared to the 2.5 times bigger value of 0.035 [mm] measured for the flow model. The trapezoidal prism shaped 3D printed model recorded a 3.7 times smaller displacement value (0.088 [mm]) compared to the adhesive resin model (0.326 [mm]) in the 50 [N] simulation, while the 10 [N] simulation recorded a displacement of 0.018 [mm], compared with the 3.777 times higher displacement recorded in the flow model. The cuboid shaped models obtained deformation values of 0.076 [mm] for the 3D printed resin and 0.195 [mm] for the adhesive resin at 50 [N], an 2.5 times difference between the 2 materials. At 10 [N] they recorded a displacement of 0.015 [mm] for the 3D model and 0.041 [mm] (2.733 times difference) for the Flow model. The lower displacement values observed show that the 3D printable resin can insure the creation of a more efficient and stable orthodontic attachments.
The degree of UV curing of conventional attachments, cured under the aligner body, are significantly lower compared with attachments cured without aligners on top of them34. In the case of the 3D printed attachments, curing is still needed but is done after the printing process in bulk, prior clinical use, considerably reducing treatment time by needing to only cure a small film of adhesive resin (200 [μm]) instead of the whole attachment body (up to 20 s for a thickness of 1 [mm]22 according to literature), for each conventional aligner attachment.
Conclusion
In conclusion, this study demonstrated quality mechanical behavior and proprieties of the aligner attachments obtained using the proposed protocol. Further development in digital protocols and the introduction of innovative materials in the process of making orthodontic clear aligner attachments, with the aim of solving current problems of the conventional procedures used in modern orthodontic treatments, represent promising horizons.
Data availability
The datasets used and/or analyzed during the current study are available from the corresponding author on reasonable request.
References
Kanwa, B. et al. Clear aligners: Where are we today? A narrative review. J. Int. Oral Health 14(3), 222. https://doi.org/10.4103/jioh.jioh_334_21 (2022).
Jedliński, M. et al. Attachments for the orthodontic aligner treatment-state of the art-a comprehensive systematic review. Int. J. Environ. Res. Public. Health. 20(5), 4481. https://doi.org/10.3390/ijerph20054481 (2023).
Nucera, R. et al. Effects of composite attachments on orthodontic clear aligners therapy: A systematic review. Materials 15(2), 533. https://doi.org/10.3390/ma15020533 (2022).
Ho, C. T., Huang, Y. T., Chao, C. W., Huang, T. H. & Kao, C. T. Effects of different aligner materials and attachments on orthodontic behavior. J. Dent. Sci. 16(3), 1001–1009. https://doi.org/10.1016/j.jds.2021.01.011 (2021).
D’Antò, V. et al. Biomechanical effects of different auxiliary-aligner designs on the rotation of an upper canine: A finite element analysis of a specific patient. Appl. Sci. 14, 2308. https://doi.org/10.3390/app14062308 (2024).
Mantovani, E. et al. Scanning electron microscopy analysis of aligner fitting on anchorage attachments. J. Orofac. Orthop. 80(2), 79–87. https://doi.org/10.1007/s00056-018-00167-1 (2019).
Goto, M. et al. A method for evaluation of the effects of attachments in aligner-type orthodontic appliance: Three-dimensional finite element analysis. Orthod. Waves 76(4), 207–214. https://doi.org/10.1016/j.odw.2017.09.001 (2017).
Savignano, R., Sandro, B., Alessandro, P. & Armando, V. R. Computer Aided Engineering of Auxiliary Elements for Enhanced Orthodontic Appliances. in Advances on Mechanics, Design Engineering and Manufacturing (Springer) 405–414.
Jia, L. et al. The effects of lingual buttons, precision cuts, and patient-specific attachments during maxillary molar distalization with clear aligners: Comparison of finite element analysis. Am. J. Orthod. Dentofac. Orthop. 163(1), e1–e12. https://doi.org/10.1016/j.ajodo.2022.10.010 (2023).
Yusong, Z., Yujun, N. & Dongxu, L. Orthodontic force measurement methods for clear aligners—A review. Measurement. 216, 112968 (2023).
Cao, L. et al. Antibacterial and fluorescent clear aligner attachment resin modified with chlorhexidine loaded mesoporous silica nanoparticles and zinc oxide quantum dots. J. Mech. Behav. Biomed. Mater. 141, 105817. https://doi.org/10.1016/j.jmbbm.2023.105817 (2023).
Yang, H. et al. Yttrium aluminum garnet-based filler resin composites used as clear aligner attachments. Dent. Mater. J. 30, 218–227. https://doi.org/10.4012/dmj.2022-15 (2023).
D’Antò, V. et al. Influence of dental composite viscosity in attachment reproduction: An experimental in vitro study. Materials 12(23), 4001. https://doi.org/10.3390/ma12234001 (2019).
Weckmann, J. et al. Influence of attachment bonding protocol on precision of the attachment in aligner treatments. J. Orofac. Orthop. 81(1), 30–40. https://doi.org/10.1007/s00056-019-00204-7 (2020).
Yaosen, C. et al. Factors of composite attachment loss in orthodontic patients during orthodontic clear aligner therapy: A prospective study. BioMed. Res. Int. 2021, 6620377. https://doi.org/10.1155/2021/6620377 (2021).
Barreda, G. J., Dzierewianko, E. A., Muñoz, K. A. & Piccoli, G. I. Surface wear of resin composites used for Invisalign® attachments. Acta Odontol. Latinoam 30(2), 90–95 (2017).
da Fausto, V., de Jardim, A., Curado, F. J. & Estrela, C. Surface wear and adhesive failure of resin attachments used in clear aligner orthodontic treatment. J. Orofac. Orthop. https://doi.org/10.1007/s00056-023-00471-5 (2023).
Ersen, K. A., Gürbüz, Ö. & Özcan, M. Evaluation of polymerization shrinkage of bulk-fill resin composites using microcomputed tomography. Clin. Oral Investig. 24(5), 1687–1693. https://doi.org/10.1007/s00784-019-03025-5 (2020).
Bucci, R. et al. Thickness of orthodontic clear aligners after thermoforming and after 10 days of intraoral exposure: A prospective clinical study. Prog. Orthod. 20(1), 36. https://doi.org/10.1186/s40510-019-0289-6 (2019).
Tepedino, M. & Ciavarella, D. A novel method for a precise and clean transfer of attachments during clear aligner therapy. AJO-DO Clin. Companion 3(5), 389–396. https://doi.org/10.1016/j.xaor.2023.08.004 (2023).
Eliades, T., Papageorgiou, S. N. & Ireland, A. J. The use of attachments in aligner treatment: Analyzing the “innovation” of expanding the use of acid etching-mediated bonding of composites to enamel and its consequences. Am. J. Orthod. Dentofac. Orthop. 158, 166–174. https://doi.org/10.1016/j.ajodo.2020.04.008 (2020).
Filtek Supreme XT Flowable Restorative. https://multimedia.3m.com/mws/media/598213O/filtek-supreme-xt-flow-tpp.pdf (2024).
Farkas, A. Z., Galatanu, S. V. & Nagib, R. The influence of printing layer thickness and orientation on the mechanical properties of DLP 3D-printed dental resin. Polymers 15, 1113. https://doi.org/10.3390/polym15051113 (2023).
Bichu, Y. M. et al. Advances in orthodontic clear aligner materials. Bioact. Mater. 22, 384–403. https://doi.org/10.1016/j.bioactmat.2022.10.006 (2022).
Elshazly, T. M. et al. Effect of attachment configuration and trim line design on the force system of orthodontic aligners: A finite element study on the upper central incisor. Orthod. Craniofac. Res. https://doi.org/10.1111/ocr.12779 (2024).
Nagib, R., Farkas, A. Z. & Szuhanek, C. FEM analysis of individualized polymeric 3D printed guide for orthodontic mini-implant insertion as temporary crown support in the anterior maxillary area. Polymers 15, 879. https://doi.org/10.3390/polym15040879 (2023).
Galatanu, S., Muntean, S., Marsavina, L., Ailinei, I. & Micota, D. Rainwater propeller pumps structural integrity. Int. J. Struct. Integr. https://doi.org/10.1108/IJSI-10-2018-0070 (2019).
Daher, R., Ardu, S., di Bella, E., Krejci, I. & Duc, O. Efficiency of 3D printed composite resin restorations compared with subtractive materials: Evaluation of fatigue behavior, cost, and time of production. J. Prosth. Dent. 131(5), 943–950 (2024).
Zamani, N. S. M. et al. Distributed force measurement and mapping using pressure-sensitive film and image processing for active and passive aligners on orthodontic attachments. IEEE Access 10, 52853–52865. https://doi.org/10.1109/ACCESS.2022.3175210 (2022).
Xu, Y., Terekhov, A., Latash, M. & Zatsiorsky, V. Forces and moments generated by the human arm: Variability and control. Exp. Brain Res. 223(2), 159–175. https://doi.org/10.1007/s00221-012-3235-0 (2012).
Li, Q. & Yang, K. Loss of attachments in patients during orthodontic therapy with clear aligners: A prospective clinical study. Orthod. Craniofac. Res. 27(2), 244–250. https://doi.org/10.1111/ocr.12710 (2024).
Krishnan, S., Pandian, S. & Rajagopal, R. Six-month bracket failure rate with a flowable composite: A split-mouth randomized controlled trial. Dental Press J. Orthod. 22(2), 69–76. https://doi.org/10.1590/2177-6709.22.2.069-076 (2017).
Ahmad, W., Jiang, F., Xiong, J. & Xia, Z. The mechanical effect of geometric design of attachments in invisible orthodontics. Am. J. Orthod. Dentofac. Orthop. 164(2), 183–193. https://doi.org/10.1016/j.ajodo.2022.11.019 (2023).
Lasance, S. J., Koletsi, D., Eliades, G. & Eliades, T. Degree of cure of orthodontic composite attachments underneath aligners. Eur. J. Oral Sci. 132(1), e12963. https://doi.org/10.1111/eos.12963 (2024).
Acknowledgements
We would like to acknowledge “Victor Babes” University of Medicine and Pharmacy, Timisoara, for their support in funding the research and in covering the costs of publication of this article. [Advanced Research Grant “Tineri Cercetatori” nr. 1683/26.01.2024].
Author information
Authors and Affiliations
Contributions
R.N. wrote the main manuscript text, devised the project, the main conceptual idea and proof outline; A.Z.F. prepared figures, designed and performed the simulations, derived the models and analyzed the data; C.S. supervised the project. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Nagib, R., Farkas, A.Z. & Szuhanek, C. Finite element analysis of the mechanical behavior of 3D printed orthodontic attachments used in aligner treatment. Sci Rep 14, 14877 (2024). https://doi.org/10.1038/s41598-024-65864-x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-024-65864-x
- Springer Nature Limited