Abstract
We propose a hybrid circuit for spoof surface plasmon polaritons (SPPs) and spatial waveguide modes to develop new microwave devices. The hybrid circuit includes a spoof SPP waveguide made of two anti-symmetric corrugated metallic strips and a traditional substrate integrated waveguide (SIW). From dispersion relations, we show that the electromagnetic waves only can propagate through the hybrid circuit when the operating frequency is less than the cut-off frequency of the SPP waveguide and greater than the cut-off frequency of SIW, generating efficient band-pass filters. We demonstrate that the pass band is controllable in a large range by designing the geometrical parameters of SPP waveguide and SIW. Full-wave simulations are provided to show the large adjustability of filters, including ultra wideband and narrowband filters. We fabricate a sample of the new hybrid device in the microwave frequencies and measurement results have excellent agreements to numerical simulations, demonstrating excellent filtering characteristics such as low loss, high efficiency and good square ratio. The proposed hybrid circuit gives important potential to accelerate the development of plasmonic integrated functional devices and circuits in both microwave and terahertz frequencies.
Similar content being viewed by others
Introduction
Surface plasmon polaritons (SPPs) are a kind of propagating surface waves bounded on the interface of metal and dielectric at the optical frequency1. In virtue of strong local-field enhancement and the diffraction limit broken, SPPs have attracted many scientists to make investigations2. The plasmonic waves propagate in directions parallel to the surface of metal and decay exponentially normal to the surface3,4. Different from metal with the characteristic of negative permittivity at the optical frequency, the metal behaves like a perfectly electric conductor in the terahertz and microwave frequencies where we cannot find SPPs tightly confined as a result5. Therefore, the spoof SPP metamaterials6,7 have been proposed to obtain the plasmon propagation at such frequencies. The metamaterials of corrugated metal structures7,8,9,10,11,12,13 such as one dimensional or two dimensional periodic arrays enchased with slits, holes or blocks have been employed to support the spoof SPP modes, which have the same dispersion relations and spatial confinements with SPPs in the optical region. For facilitating the application of spoof SPPs, broadband and high-efficiency conversion and transition14,15 between traditional transmission line and conformal SPPs with double grating and single grating have been reported, which allow for successful combination between the spatial guided waves and SPPs. At the same time, some devices based on spoof SPPs have been developed, including ultra-wideband surface plasmonic filter16, efficient converter17,18 between SPP modes and spatial radiated modes and controlling rejecter of SPPs19 and so on20,21,22,23,24. All of the reported papers attest that the spoof SPPs can provide the advantage of miniaturization and localized electromagnetic (EM) waves in subwavelength scales.
The substrate integrated waveguide (SIW) and similar schemes25,26,27,28,29 have been put forward in recent years as new spatial guided-wave structures, which can be integrated in the dielectric substrate with the characteristics of low insertion loss and low radiation. Compared with the traditional expensive and cumbersome waveguide, SIWs have similar performance but more compact dimensions, which makes it possible to downsize the microwave system into a small package.
In this article, we propose a hybrid circuit of the spoof SPP waveguide which supports SPP modes and SIW that is a barrier of spatial guided modes. The spoof SPP waveguide takes the advantage of the anti-symmetrical corrugated metallic strips22 which bring further tighter EM field confinement and smaller propagating wavelength for decreasing the interference and miniaturizing the system at the same frequency. Linear tapered microstrip lines27,30 serve as a bridge to connect the SPP waveguide, SIW and microstrip line, attaining the conversions among the transverse magnetic (TM) mode, transverse electric (TE) mode and quasi-transverse-electromagnetic (TEM) mode. Numerical and experimental resulted are present to validate the new features of the hybrid circuit.
Results
Hybrid circuit of spoof SPP waveguide and SIW
We propose a hybrid circuit that contains a spoof SPP waveguide, SIW and tapered microstrip lines, as illustrated in Fig. 1. The hybrid circuit is divided into two main sections of SPP waveguide and SIW. The commercial printed circuit board, F4B31, is used as the dielectric substrate with thickness of t = 0.5 mm and relative permittivity of 2.65. We choose annealed copper (electric conductivity σ = 5.8e + 007 S/m) as metal layers whose thickness is 0.018 mm. The first main section of the hybrid circuit is the spoof SPP waveguide, which is composed of two anti-symmetrical corrugated metallic strips22. Figure 1(a) shows a unit cell of the SPP waveguide, where a and h denote the groove width and depth and d is strip width, respectively. The SPP waveguide is formed by arranging such unit along the x-axis with period p on the top and bottom surfaces of the dielectric substrate.
In the second main section, we adopt a typical configuration of SIW32, whose unit cell is depicted in Fig. 1(b). The upper and lower surfaces of the dielectric substrate are metal layers and the dielectric substrate is separated by two rows of metallic via holes which are separated by a certain distance D1. The period of via holes and via diameter are donated as p1 and r, respectively.
The two main sections are connected by tapered microstrip lines. There are a variety of tapered microstrip-line forms, such as arc taper lines and linear taper lines. Here, we choose the linear tapered microstrip lines27. Figure 1(c,d) illustrate three tapered microstrip lines, including the connection between 50 Ω-microstrip line and the SPP waveguide, the connection between SPP waveguide and SIW, along with the connection between SIW and 50 Ω-microstrip line. In such figures, L2, L3, L4 and w1, w2, w3, w4, w5, w6 represent the lengths and widths of such three tapers, respectively. The first taper (part L2 and L6) is used to transform the quasi-TEM mode of the microstrip line into the TM mode of the SPP waveguide, the second taper (part L3) is for the transformation from the TM mode to the TE10 mode and the last taper (part L4) transforms the TE10 mode to the quasi-TEM mode.
We employ the eigen-mode solver of the commercial software, CST Microwave Studio, to calculate the dispersion relations of the SPP waveguide and comprehending propagation characteristics of the waveguide. In CST Microwave Studio, we set the boundary condition as periodic in the x axis and electric (Et = 0) in both y and z axes. Owing to the physical intermodal coupling for the forward mode and backward mode, there will be totally reflection of the incident energy when the working frequency is upper than the cutoff frequency33. That is to say, while the input frequencies outweigh the cutoff frequency, the propagating wave vectors of the forward and back-forward modes have the opposite directions but the same value, which result in the zero transmission.
It is rather difficult to analyze the hybrid circuit directly. Considering the fact that SIW is composed of two metal surfaces and two rows of metallic via holes to approximate a kind of rectangular waveguide, we can establish the corresponding relationship between the traditional rectangular waveguide and SIW. Then the design of SIW devices can be changes as the design of traditional rectangular waveguide devices, which thereby greatly reduces the complexity and design time. Thus, in ref. 32, the authors made use of accurate results obtained from the method of lines to derive an empirical equation for the normalized width of SIW, which is convenient and handy for design32:
where
in which is the equivalent width of SIW. From the formula, the corresponding equivalent waveguide width can be straightly launched from the structural parameters (D1, p1 and r) of the designed SIW. The phase characteristics can be obtained from the theoretical analysis of the equivalent metal waveguide. Meanwhile, the dispersion relationship of SIW and the light line in the dielectric substrate are calculated analytically as
Then the dispersion curves of the designed SPP waveguide and SIW and the light line in dielectric substrate are illustrated in Fig. 2(a), as marked by black, blue and magenta lines, respectively. Here, the geometrical parameters are chosen as p = 1.5 mm, a = 0.6 mm, h = 1.5 mm, d = 2 mm; D = 10.31 mm, r = 0.5 mm, D1 = 8.81 mm and p1 = 1.1 mm, acquiring the equivalent width a′ = 8.5173 mm. From the blue and black curves, we notice that there is a significant transmission passband between the cutoff frequencies of SPP waveguide and SIW for the designed geometrical parameters.
In Fig. 2(b), we clearly observe that the dispersion curve of SPP waveguide deviates gradually from the light line when k/π grows up and that the curves asymptotically approach to different cutoff frequencies as the groove depth h increases from 1.0 to 1.9 mm. Consequently, on the basis of different groove depths, we can achieve various dispersion curves and propagating vectors on the SPP waveguides. However, the dispersion curve of the spoof SPP has a tendency to the light line by decreasing the groove depth. Figure 2(c) shows dispersion curves of SIW, which is gradually close to the light line. It is obvious that the propagation constant k is greater than zero when the frequencies are greater than the cutoff frequency. When the equivalent width are chosen as 11.9102 mm (D = 14.42 mm, p1 = 1.54 mm, r = 0.7 mm and D1 = 12.32 mm), 10.2487 mm (D = 12.40 mm, p1 = 1.32 mm, r = 0.6 mm and D1 = 10.6 mm), 6.8138 mm (D = 8.248 mm, p1 = 0.88 mm, r = 0.4 mm and D1 = 7.048 mm) and 5.1104 mm (D = 6.186 mm, p1 = 0.66 mm, r = 0.3 mm and D1 = 5.286 mm), we notice that the cutoff frequency of SIW increases with the decrease of the equivalent width. For the tunable performance of the spoof SPPs and SIW, we can realize expediently controls of upper and lower cutoffs of the passband, generating controllable band-pass filters.
Numerical simulations and physical interpretations
To better understand the influence of groove depth h and equivalent width a′ on the transmission coefficient, we design the SPP-SIW hybrid circuits with different parameters. The simulated transmission coefficients of the hybrid circuit by the time-domain solver in CST Microwave Studio are demonstrated in Fig. 3(a), in which we set boundary conditions open spaces in all directions. We easily discover that the groove depth can control independently the upper cutoff frequency of the pass band but has little influence on the lower cutoff frequency, where L1 = 4.0373 mm, L2 = 12.5854 mm, L3 = 10.3163 mm, L4 = 15.9112 mm, L5 = 4.8488 mm, L6 = 10.3605 mm, a′ = 8.5173 mm and h ranges from 1 mm to 1.9 mm. For the black (h = 1.2 mm), red (h = 1.4 mm), blue (h = 1.6 mm) and green (h = 1.9 mm) curves, their −3 dB bandwidths are 15.84 GHz, 11.73 GHz, 9.39 GHz and 5.91 GHz, respectively. Corresponding to the above curves, their highest transmission coefficients are −0.82 dB, −0.86 dB, −0.95 dB and −1.1 dB, respectively. Figure 3(b) depicts that the equivalent width of SIW can control the lower cutoff frequency of the pass band but has little influence on the upper cutoff frequency, in which most of the parameters have the same values as above except that h = 1.5 mm and a′ranges from 11.9102 mm to 5.11024 mm. Corresponding to the red, black, blue and magenta curves, The −3 dB bandwidths are 13.57 GHz, 12.54 GHz, 7.7 GHz and 2.28 GHz, respectively, with the highest transmission coefficients as −0.83 dB, −0.86 dB, −1.1 dB and −1.5 dB. Hence, it is convenient to control the upper and lower cutoff frequencies by adjusting the groove depth and equivalent width with lower loss.
Based on these characteristics, we design an ultra-wide pass-band filter and a narrow pass-band filter, whose simulated transmission coefficients are exhibited in Fig. 3(c). The ultra-wideband filter has the −3 dB bandwidth of 14.4 GHz (from 8.01 to 22.41 GHz) and the highest transmission coefficient of −0.81 dB with h = 1.4 mm and a′ = 11.9102 mm; while the narrow-band filter has the −3 dB bandwidth of 1.89 GHz (from 16.11 to 18.00 GHz) and the highest transmission coefficient of −1.45 dB with h = 1.8 mm and a′ = 5.9621 mm (D = 7.217 mm, p1 = 0.77 mm, r = 0.35 mm and D1 = mm). Certainly, all the transmission coefficients shown in Fig. 3 have excellent filtering characteristics with minimum insertion loss less than −1.5 dB. It is well known in the microwave community that the designs of the ultra-wideband filter and narrow-band filters are big challenges by using the conventional filter synthesize methods, such as the LC filter circuits and guided-wave circuits. The proposed hybrid SPP-SIW circuit solves the problems. Most importantly, compared with the previous ultra-wideband filters based on either SPP16 or SIW34,35, the main physical significance of this device is the successful conversion between the SPP modes and spatial-waveguide modes in either wideband or narrowband, which is controllable by a simple parameter.
To get a physical insight into the SPP-SIW hybrid circuit, we discuss the near electric fields (z-components) on the x–y plane, which is in the central plane inside the dielectric substrate. In CST Microwave Studio, we set up a field monitor for electric fields at a few frequencies. We take a sample waveguide with the parameters chosen in Fig. 2(a) and the simulated field distributions are illustrated in Fig. 4(a,c) at the lower frequency stopband and upper frequency stopband, where there are no fields at 9 GHz in SIW and at 20 GHz in SPP waveguide, respectively. At 9 GHz of the lower stopband, the waves stop propagating in the beginning of SIW; at 20 GHz of the upper stopband, the waves are cutoff on the SPP waveguide after the matching section. However, within the pass band, the waves are propagating through the SPP waveguide and SIW with very small loss, as shown in Fig. 4(b). We notice that the tapered microstrip lines can effectively realize the coupling and conversion among different propagating waves in the hybrid circuit. This provides an intuitionistic proof to corroborate the transmission waveguide filtering performance.
Measurement results and discussions
To further study the operation performance quantitatively of the SPP-SIW hybrid circuit, we fabricate a sample using the F4B substrate, as exhibited in Fig. 5(a,b) for the front and back views which are photographed by Qian Zhang. The length and width of the fabricated sample are 124.899 and 20 mm, respectively. The groove depths h = 1.5 mm and equivalent width a′ = 8.5173 mm are chosen in this experiment. We use two 50 Ω coaxial lines to connect the fabricated sample welded two standard SMA connectors and the Agilent vector network analyzer (VNA, N5230C). We have measured the S scattering parameters of the sample, as illustrated by the red and black dotted lines in Fig. 5(c). As comparisons, numerical simulations are also given in the same figure, as shown by the red and black solid lines. It is clearly observed that the simulated results have excellent agreements to the measured results. From the reflection coefficients (S11), we note that S11 is almost less than −10 dB in the whole frequency band from 11.92 to 21.54 GHz. From the transmission coefficients (S21), we notice that the proposed circuit has excellent filtering characteristics such as high transmission, good bandpass and great square ration. The maximum transmission coefficient can reach −0.5 dB and the −3 dB bandwidth is as high as 9.62 GHz.
Regarding to the important parameter of a filter, the square ratio, the calculation formula is written as:
It is widely known that is closer to one and the rectangle is more steep. This value is a very good proof of the quality of the square ratio. For the simulation results of this sample, the working frequencies of −20 dB are 10.86 GHz and 22.28 GHz. Hence we can obtain . It is because of two points that the filter has such a good square ratio. Through analyzing dispersion curves and electric-field distributions, we unambiguously acquaint that the lower and upper cutoff frequencies are controlled by SIW and SPP waveguide, respectively. Hence, one point is based on SIW. Since we can get the SIW properties from theoretical analysis of equivalent metal waveguide, the TE10 mode of SIW is described by
in which . We call it the decaying mode which is a rapidly attenuating oscillation mode. Hence there are no energy and power transmitting.
The other point is because of the spoof SPPs. When , the energy and wave vectors of the forward modes are in the opposite direction from the backward modes. As a result, the propagation constants of the forward and backward modes become vestigial, leading to the total reflection. Then the propagation velocity becomes zero and there are no energy and power.
Conclusion
Utilizing the traditional SIW and spoof SPP waveguide designed with antisymmetrical corrugated metallic strips, we have proposed a novel hybrid circuit to develop highly efficient and pass-band controllable filters. Owning to the highly confined EM waves of SPPs and lower radiation losses of SIW, the proposed hybrid circuit has excellent transmission efficiency and low loss. Meanwhile, the good square ratio benefits from the total reflections of SPPs and decaying modes of SIW. We have modulated the groove depth and equivalent width to design ultra wideband and narrowband filters, whose performances are splendid as well. To verify the marvelous capability, we have fabricated a sample using the commercial dielectric substrate, F4B. Both simulation and measurement results have demonstrated the highly efficient transmissions. The proposed SPP-SIW hybrid circuit and tunable passband filters provide potentials to advanced plasmonic functional devices and integrated circuits.
Methods
All numerical simulations of SPP units, hybrid circuits and E-fields are performed by the commercial software, CST Microwave Studio, whose modeling circumstance has been explicated in details. F4B, a kind of Teflon woven, is used for the simulation model and experimental fabrication. Figure 6 shows the real part and imaginary part of the dielectric constant, respectively. It can be clearly observed that F4B is relatively stable in the simulation band and its dispersion has little effect on the simulation and experiment results.
Additional Information
How to cite this article: Zhang, Q. et al. A Hybrid Circuit for Spoof Surface Plasmons and Spatial Waveguide Modes to Reach Controllable Band-Pass Filters. Sci. Rep. 5, 16531; doi: 10.1038/srep16531 (2015).
References
Stewart, M. E. et al. Nanostructured plasmonic sensors. Chem. Rev. 108, 494–521 (2008).
Barnes, W. L., Dereux, A. & Ebbesen, T. W. Surface plasmon subwavelength optics. Nature 424, 824–830 (2003).
Harvey, A. Periodic and guiding structures at microwave frequencies. IEEE T. Microw. Theory 8, 30–61 (1960).
Maier, S. A. Plasmonics: fundamentals and applications: fundamentals and applications. (Springer Science & Business Media, 2007).
Kumar, G., Cui, A., Pandey, S. & Nahata, A. Planar terahertz waveguides based on complementary split ring resonators. Opt. Exp. 19, 1072–1080 (2011).
Pendry, J., Martin-Moreno, L. & Garcia-Vidal, F. Mimicking surface plasmons with structured surfaces. Science 305, 847–848 (2004).
Garcia-Vidal, F., Martin-Moreno, L. & Pendry, J. Surfaces with holes in them: new plasmonic metamaterials. J. Opt. A- Pure. Appl. Op. 7, S97 (2005).
Hibbins, A. P., Evans, B. R. & Sambles, J. R. Experimental verification of designer surface plasmons. Science 308, 670–672 (2005).
Fernández-Domínguez, A., Moreno, E., Martin-Moreno, L. & Garcia-Vidal, F. Terahertz wedge plasmon polaritons. Opt. Lett. 34, 2063–2065 (2009).
Martin-Cano, D. et al. Domino plasmons for subwavelength terahertz circuitry. Opt. Exp. 18, 754–764 (2010).
Zhou, Y. J. & Cui, T. J. Broadband slow-wave systems of subwavelength thickness excited by a metal wire. Appl. Phys. Lett. 99, 101906 (2011).
Shen, X. & Cui, T. J. Planar plasmonic metamaterial on a thin film with nearly zero thickness. Appl. Phys. Lett. 102, 211909 (2013).
Wood, J., Tomlinson, L., Hess, O., Maier, S. & Fernández-Domínguez, A. Spoof plasmon polaritons in slanted geometries. Phys. Rev. B 85, 075441 (2012).
Ma, H. F., Shen, X., Cheng, Q., Jiang, W. X. & Cui, T. J. Broadband and high‐efficiency conversion from guided waves to spoof surface plasmon polaritons. Laser & Photon. Rev. 8, 146–151 (2014).
Liao, Z., Zhao, J., Pan, B. C., Shen, X. P. & Cui, T. J. Broadband transition between microstrip line and conformal surface plasmon waveguide. Journal of Physics D: Appl. Phys 47, 315103 (2014).
Gao, X., Zhou, L., Liao, Z., Ma, H. F. & Cui, T. J. An ultra-wideband surface plasmonic filter in microwave frequency. Appl. Phys. Lett. 104, 191603 (2014).
Sun, S. et al. Gradient-index meta-surfaces as a bridge linking propagating waves and surface waves. Nat. Mater. 11, 426–431 (2012).
Xu, J. J., Zhang, H. C., Zhang, Q. & Cui, T. J. Efficient conversion of surface-plasmon-like modes to spatial radiated modes. Appl. Phys. Lett. 106, 021102 (2015).
Pan, B. C., Liao, Z., Zhao, J. & Cui, T. J. Controlling rejections of spoof surface plasmon polaritons using metamaterial particles. Opt. Exp. 22, 13940–13950 (2014).
Yang, Y., Shen, X., Zhao, P., Zhang, H. C. & Cui, T. J. Trapping surface plasmon polaritons on ultrathin corrugated metallic strips in microwave frequencies. Opt. Exp. 23, 7031–7037 (2015).
Liu, X. et al. Planar surface plasmonic waveguide devices based on symmetric corrugated thin film structures. Opt. Exp. 22, 20107–20116 (2014).
Zhang, H. C. et al. Broadband amplification of spoof surface plasmon polaritons at microwave frequencies. Laser & Photon. Rev. 9, 83–90 (2015).
Yin, J. Y., Ren, J., Zhang, H. C., Pan, B. C. & Cui, T. J. Broadband Frequency-Selective Spoof Surface Plasmon Polaritons on Ultrathin Metallic Structure. Sci. Rep. 5, 8165, 10.1038/srep08165 (2015).
Zhang, H. C., Cui, T. J., Zhang, Q., Fan, Y. & Fu, X. Breaking the challenge of signal integrity using time-domain spoof surface plasmon polaritons. ACS photonics 2, 1333–1340 (2015).
Uchimura, H., Takenoshita, T. & Fujii, M. Development of a “laminated waveguide”. Microwave Theory and Techniques, IEEE T. Microw. Theory 46, 2438–2443 (1998).
Hirokawa, J. & Ando, M. Single-layer feed waveguide consisting of posts for plane TEM wave excitation in parallel plates. IEEE T. Antennas Propag. 46, 625–630 (1998).
Deslandes, D. & Wu, K. Integrated microstrip and rectangular waveguide in planar form. IEEE Microw. Wirel. Co. 11, 68–70 (2001).
Wu, K. & Boone, F. Guided-wave properties of synthesized nonradiative dielectric waveguide for substrate integrated circuits (SICs). Microwave Symposium Digest, 2001 IEEE MTT-S International Vol. 2, 723–726 (IEEE, 2001).
Zeid, A. & Baudrand, H. Electromagnetic scattering by metallic holes and its applications in microwave circuit design. IEEE T. Microw. Theory 50, 1198–1206 (2002).
Harrington, R. F. Time-harmonic electromagnetic fields. (McGraw-Hill, 1961).
Wang Ling Insulating Materials Factory, Teflon Woven Series: Glass Fabric Copper-clad Laminates (datasheet) (2014).
Yan, L., Hong, W., Wu, K. & Cui, T. J. Investigations on the propagation characteristics of the substrate integrated waveguide based on the method of lines. IEE Proc.—Microw. Antennas Propag. 152, 35 (2005).
He, S., He, Y. & Jin, Y. Revealing the truth about ‘trapped rainbow’storage of light in metamaterials. Sci. Rep. 2, 583, 10.1038/srep00583 (2012).
Hao, Z.-C., Hong, W., Chen, J.-X., Chen, X.-P. & Wu, K. Compact super-wide bandpass substrate integrated waveguide (SIW) filters. Microwave Theory and Techniques, IEEE T. on 53, 2968–2977 (2005).
Mira, F., Mateu, J., Cogollos, S. & Boria, V. E. Design of ultra-wideband substrate integrated waveguide (SIW) filters in zigzag topology. Microwave and Wireless Components Letters, IEEE 19, 281–283 (2009).
Acknowledgements
This work was supported in part by the National Science Foundation of China (60990320, 60990324 and 61138001), in part by National High Tech (863) Projects (2012AA030402 and 2011AA010202) and in part by the 111 Project (111-2-05).
Author information
Authors and Affiliations
Contributions
Q.Z. and H.C.Z. contributed equally to this work. Q.Z., H.C.Z and H.W simulated and optimized the waveguide model. Q.Z., H.C.Z. and T.J.C. were responsible for providing ideas, scientific explanations and performing the measurements. Q.Z., H.C.Z. and T.J.C. wrote the paper based on the input from all authors. All authors devoted to the discussions.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Zhang, Q., Zhang, H., Wu, H. et al. A Hybrid Circuit for Spoof Surface Plasmons and Spatial Waveguide Modes to Reach Controllable Band-Pass Filters. Sci Rep 5, 16531 (2015). https://doi.org/10.1038/srep16531
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep16531
- Springer Nature Limited