Abstract
The “perfect” vortex is a new class of optical vortex beam having ring radius independent of its topological charge (order). One of the simplest techniques to generate such beams is the Fourier transformation of the Bessel-Gauss beams. The variation in ring radius of such vortices require Fourier lenses of different focal lengths and or complicated imaging setup. Here we report a novel experimental scheme to generate perfect vortex of any ring radius using a convex lens and an axicon. As a proof of principle, using a lens of focal length f = 200 mm, we have varied the radius of the vortex beam across 0.3–1.18 mm simply by adjusting the separation between the lens and axicon. This is also a simple scheme to measure the apex angle of an axicon with ease. Using such vortices we have studied non-collinear interaction of photons having orbital angular momentum (OAM) in spontaneous parametric down-conversion (SPDC) process and observed that the angular spectrum of the SPDC photons are independent of OAM of the pump photons rather depends on spatial profile of the pump beam. In the presence of spatial walk-off effect in nonlinear crystals, the SPDC photons have asymmetric angular spectrum with reducing asymmetry at increasing vortex radius.
Similar content being viewed by others
Introduction
Spontaneous parametric down-conversion (SPDC)1,2, one of the most important nonlinear processes, is of paramount interest especially in the field of quantum optics3 for its intrinsic capability in generating entangled photon pairs. In this process, a photon (pump) of higher energy while interacting with second order nonlinear crystals splits into a pair of low energy photons (signal-idler) subject to energy conservation and phase matching. Depending upon the phase matching conditions inside the nonlinear crystals, the down converted photons are known to be emitted in variety of spatial distributions. For example, pump beam of Gaussian mode under type-I (where the signal and idler have same polarization but orthogonal to the pump polarization), non-collinear phase-matching produces down converted photons in an annular ring, with photon of each pair at diametrically opposite points. As such, these photon pairs are entangled in the spatial degrees of freedom4 and other degrees of freedom including orbital angular momentum (OAM)5. The angular spectrum and hence the entanglement properties of these paired photons are highly influenced by different crystal parameters including birefringence and length and the spatial structure of the pump beam6. Therefore, it is imperative to study the angular spectrum of the SPDC photons for different crystal parameters, pump beams of different spatial structures and OAM.
Optical vortices having phase singularities (phase dislocations) in the wavefront, carries vanishing intensity at the singular point. Due to the screw-like (helical) phase structure around the point of singularity, such beams carry OAM. The characteristic phase distribution of optical vortices is represented as exp(ilθ), where θ is the azimuthal angle. The integer l is called the topological charge or the order of the vortex. It has been observed7 that the OAM of the classical beam can be transferred to the heralded single photon generated through SPDC process. Therefore, it is important to study the spatial distribution of the SPDC photons while pumped with different order optical vortices. Recently we have reported8 that unlike Gaussian beam, the vortex pump beams produce SPDC photons in asymmetric annular rings and the asymmetry increases with the order of the vortex. As the divergence9 and the radius of the vortex beam increases with its order10, it is difficult to ascertain the contribution of the spatial distribution of the vortex beam and it’s OAM in the asymmetry of SPDC ring separately.
Recent development in the field of structured beams have resulted in a special class of optical vortices, known as perfect vortices11, where the radius of the vortex ring is independent of its order. Experimentally realizable annular field profile of the perfect vortex with topological charge l at a fixed propagation distance may be written as12
where, () are polar coordinates, and are the radius and annular width of the perfect vortex. Among different techniques12,13,14, Fourier transformation of the Bessel-Gauss (BG) beam of different orders14 is the simplest technique to generate perfect vortices. The axicon, an optical element with a conical surface, converts Laguerre-Gaussian (LG) beams into BG beams15,16. The order of the BG is the same as that of the input LG beams. The Gaussian (zero order LG beam) input beam results in 0th order BG beam. Fourier transformation of such BG beams using a lens of focal length, f, results perfect vortex at the back focal plane with field amplitude distribution given as13
where, wg is the beam waist radius of the Gaussian beam confining the BG beam, Il is the lth order modified Bessel function of first kind and 2wo (wo = 2f/kwg, the Gaussian beam waist at the focus) is the annular width of the perfect vortex of ring radius governed by the relation13,
where, n and α are the refractive index and base angle of the axicon respectively. As evident from Eqn. (3), for given axicon parameters, the radius of the perfect vortex is constant for a lens and linearly varying with the focal length of the Fourier transforming lens.
However, for all practical purposes12,17,18, one need to vary the radius of the vortex ring, which requires either a number of Fourier transforming lenses of different focal lengths and or imaging systems of different demagnification factors. As such, both of these options can provide variation (only discrete values) in the vortex ring radius, definitely, at the cost of increased experimental complexity. Here we present a novel technique to generate perfect vortices with continuously varying annular ring radius. As a proof of principle, we have generated perfect vortices of topological charge as high as l = 6 with annular ring radius continuously varying from 0.3–1.18 mm. This novel experimental scheme can potentially be used as a quick and simple technique to measure the apex angle of an axicon. Pumping a nonlinear crystal using such vortices of different ring radius we have studied the angular spectrum of the down converted photons and experimentally observed that the angular spectrum of the down converted photons is dictated by the spatial profile of the pump but not it’s OAM. However, the asymmetry in the angular spectrum which is detrimental to the entanglement quality of the SPDC source19, depends on the size of the input beam. Using the variable size perfect vortex we have experimentally found, for a given nonlinear crystal (birefringence parameter and length) the input beam radius required to generate symmetric angular spectrum of the down converted photons.
Results
Theory
According to the Fourier transformation theory20, any object can be Fourier transformed by placing the object behind the lens at any arbitrary distance D from the focal plane. The basic principle of the technique is pictorially represented in Fig. 1(b), where the object (axicon) placed at a distance (f–D) behind the lens of focal length, f, is Fourier transformed into perfect vortex at the back focal plane for input vortex beams. The amplitude distribution of the perfect vortex at the back focal plane is given by
In the current system configuration, the width of the perfect vortex is 2wD = 1.65 × 2wo14. For large value of , the modified Bessel function, Il can be approximated to13
Therefore, Eqn. (4) can be reduced to
The Eqn. (6) has similar functional form as Eqn. (1) with additional quadratic phase factor and a scale factor. As we are dealing with the intensity of the perfect vortex beam at focal plane, the quadratic phase does not make any difference in our current study. The perfect vortex ring is formed at, with a modified ring radius,
As evident from Eqn. (7), the radius of the perfect vortex can be varied simply by moving the axicon away from the back focal plane of the lens. For ring radius to be zero the axicon required to be placed at the focal plane of the lens which is impractical for many applications. On the other hand, for D → 0, the Fourier transform relation breaks down. Therefore, the value of D can be varied practically within the range of 0 < D < f.
Experiment
The schematic of the experimental setup is shown in Fig. 1(a). A UV diode laser (Toptica- TopMode 405) of 100 mW power at 405 nm with spectral width ~12 MHz is used as the pump source. Two spiral phase plates, SPP1 and SPP2 are used to convert Gaussian beam into optical vortices (LG beams) of order, l = 1 and l = 2, respectively, at conversion efficiency >95%. Due to limited availability of SPPs producing vortices of order l > 2, using a vortex-doubler setup21 (see methods) we have generated optical vortices of orders (topological charges) up to l = 6. The axicon with apex angle 178° converts the vortex beam of order l into BG beam of the same order. The Fourier transforming lens (f = 200 mm) placed before the axicon with a separation of f-D (D is the distance of the axicon from Fourier plane) produces the perfect vortices at its back focal plane. The 5 mm long β-BaB2O4 (BBO) nonlinear crystal converts the pump photons at 405 nm into degenerate down converted photons at 810 nm in non-collinear phase-matching at 3° with respect to the pump beam direction. Due to circular symmetry, the photons are generated in a cone of apex angle 6° and the photons of each pair are situated in diametrically opposite points. A second lens, f = 50 mm Fourier transforms the generated SPDC ring which is recorded using EMCCD after filtering the pump photon using an interference filter of 10 nm bandwidth centred at 810 nm.
Discussions
To verify the generation of perfect vortex, we have recorded the intensity profile of the beam at the back focal plane of the Fourier transforming lens (f = 200 mm) using a CCD camera with the results shown in Fig. 2. The axicon is placed at D = 160 mm before the Fourier plane. As evident from the intensity profile of the vortex beams of topological charge l = 1 and l = 5 shown in Fig. 2(a,b) respectively, both the beams have same annular ring radius, ρr = 1.18 mm confirming the generation of vortices having annular ring radius independent of topological charge, perfect vortex. To confirm the vorticity and order of the perfect vortex, the vortex beam is interfered with a Gaussian beam at 405 nm with interference pattern shown in second column of Fig. 2. A close observation of the interference pattern of Fig. 2(c,d) reveals the characteristic spiral patterns at the annular ring of the beams corresponding to vortex orders l = 1 and l = 5 respectively. Unlike the spiral fringe pattern as observed in the interference of normal vortex beam with Gaussian beam, the spiral fringes in Fig. 2(c,d) is not visible at the center of the interference pattern due to the large dark core of the perfect vortices. Such observation clearly ascertain the capability of our experimental scheme in generating high-quality perfect optical vortices even at higher values of topological charges. Using Eqn. 6 along with the experimental parameters we have theoretically calculated the intensity profile of the perfect vortex and their interference pattern with Gaussian beam with the results shown in third (e–f) and fourth (g–h) column of Fig. 2 respectively. We can clearly see a close matching between theoretical and experimental results.
With the successful generation of perfect vortices with orders as high as l = 6, we experimentally confirmed the variation of perfect vortex radius on demand. As a proof of principle, we recorded the intensity pattern of the perfect vortex of topological charge l = 3 at the Fourier plane for three different axicon positions, D = 40, 100 and 160 mm, with the results shown in Fig. 3. As evident from first row (a–c) of Fig. 3, the annular ring has radius ρr = 0.3 mm, 0.75 mm and 1.18 mm for the D- value of 40 mm, 100 mm and 160 mm respectively. In principle, the annular ring radius can further be reduced by decreasing the D-value, however, due to the mechanical constrain arising from the CCD camera structure and related optical components (attenuators) we could not record experimentally the perfect vortex of ring radius, ρr < 0.3 mm by placing the axicon with separation D < 40mm. To avoid such mechanical constrain in recording the vortex ring radius for D < 40 mm, which is beyond the scope of present study, one can easily image the Fourier transforming plane to other measurement planes. On the other hand, further increase in vortex ring radius requires Fourier transforming lenses of longer focal lengths. Using Eq. (6) along with the experimental parameters, we have also theoretically calculated the intensity profile of the vortex of l = 3 as shown in second row (d–f) of Fig. 3, in close agreement with the experimental results. The slight mismatch in the theoretical and experimental values of vortex ring radius can be attributed to the inaccuracy of the apex angle used in theoretical study. To get more insight about the possibility of varying the ring radius of vortices of all orders, we have measured the ring radius of the vortices of three different orders l = 0, 2 and 6 (l = 0 is the Gaussian beam) with the results shown in Fig. 4. As evident from Fig. 4, the annular ring of the Gaussian as well the vortices of both orders have same radius for a fixed position of the axicon and increases linearly with the increase of D-value. Using Eq. (7) and axicon parameters (base angle α = 1° and refractive index, n = 1.5302 at 405 nm) we found a clear mismatch between theoretical (solid line) and experimental results. The theoretical and experimental variation of ring radius with axicon distance have slope of 9.23 × 10−3 and 7.33 × 10−3 respectively. From the experimentally measured slope (7.33 × 10−3) we found the apex angle of the axicon to be 178.40 slightly higher than the value 178° presented by the manufacturer. To verify the manufacturing inaccuracy in the apex angle of the axicon, we have repeated the same experiment for three different laser wavelengths (532 nm, 632 nm and 1064 nm). As expected, the annular ring radius increases with axicon position (D) away from the Fourier plane for all three wavelength at a slope of ~6.83 × 10−3, 7.05 × 10−3 and 7.05 × 10−3 for 532 nm, 632 nm and 1064 nm respectively. Using the refractive indices of the BK-7 glass we found the axicon to have apex angle of 178.4° ± 0.03° similar to the value measured previously. Such study also proves that the present experimental scheme (Fig. 1(b)) can be used as a quick and simple way of measuring the apex angle of an axicon. However, the measurement on the shape of the axicon tip and other axicon parameters requires sophisticated equipment including optical profilometer22.
To study the contribution of OAM in the angular spectrum of the down converted photons, we pumped the nonlinear crystal (BBO) placed at the Fourier plane after the axicon using perfect vortices of different orders and ring radii. The angular spectrum or transverse momentum distribution of the down converted photons, obtained from the Fourier transformation of the generated photons using a convex lens of focal length, f = 50 mm in f-f optical system configuration, is recorded using EMCCD. Each pixel represents a particular transverse position r of the down converted photons, which corresponds to a transverse momentum value, K = [ωdc/(c f )]r, where, ωdc is the frequency of the down converted photons, c is the velocity of light in free space and f is the focal length of the Fourier transforming lens. In the current study we have used two topological charges, l = 0 (Gaussian beam) and l = 3 and varied their ring radius ρr for different axicon positions (D-value) and recorded the angular spectrum of the down converted photons with the results shown in Fig. 5. First row, (a–c) and second row, (d–f), of Fig. 5 represents the angular spectrum of the down converted photons corresponding to pump radius, ρr = 0.3, 0.75 and 1.18 mm for l = 0 and l = 3 respectively. Kx and Ky are the transverse momentum components of the down converted photons. As evident from the Fig. 5, for a given annular ring radius ρr of both the topological charges, l = 0 and l = 3, the down converted photons have identical transverse profiles with intense inner and outer rings and intensity gradient in between. Therefore, it can be concluded that the OAM of the input pump beam has no effect in the transverse distribution of the down converted photons. However, it should be noted that the sum of the OAMs of signal and idler photons of each pair will be equal to the OAM of the input pump photon23. The dark spot at the centre of each transverse momentum distribution can be attributed to the back ground correction used to avoid the pump beam leaked through the interference filter. Although the increase in pump beam radius does not modify the size of the transverse momentum profile of the down converted photons, at lower pump beam size the down converted photons have asymmetric transverse momentum distribution. Such asymmetry arising from the Poynting vector walk-off in the birefringent crystals are observed for tightly focused beams of radius smaller or equivalent to the lateral displacement of the beam, L tanρo in the nonlinear crystal of length, L and birefringence parameter, ρo. For L = 5 mm and ρo = 67.44 mrad of the BBO crystal, the L tanρo value is calculated to be 0.34 mm. As a result, we can expect asymmetric transverse distribution in down converted photons for pump beam radius, ρr = 0.3 mm.
However, the asymmetry in the transverse momentum distribution of the down converted photons is detrimental for entangled photon sources23 and for all practical purposes, one need symmetric distribution. Therefore, we have studied the asymmetry in transverse momentum distribution of the down converted photons quantitatively with the radius of the perfect vortex beam. The results are shown in Fig. 6. The asymmetry factor, ξ is defined as ξ = 1 − a/b, where a and b representing the separation between the inner and out radii on left and right sides of the angular spectrum of the down converted photons respectively as shown in inset of the Fig. 6. We have calculated the asymmetry factor, ξ, for different size of the perfect vortex of order l = 3. As evident from the Fig. 6, the ξ value decreases linearly with the increase of perfect vortex ring radius. Although it is expected to have symmetric angular spectrum of the down converted photons for the input vortex ring radius ρr > L tanρo (>0.34 mm), we still observe a certain degree of asymmetry in angular spectrum at higher values of ρr. However, for ρr = 1.18 mm (~3 × L tanρo) we have observed symmetric (ξ < 10%) angular spectrum of the down converted photons. Such study ascertain the need of proper beam diameter of the input structured beam (here, perfect vortex beam) depending upon the birefringence and length of the nonlinear crystal for entangled photon sources.
Methods
The schematic of the experimental setup is shown in Fig. 1(a). A pump diode UV laser (Toptica- TopMode 405) of 100 mW at 405 nm with spectral width ~12 MHz is used as the pump laser. The power to the nonlinear crystal is controlled by using a combination of half-wave plate (λ/2) and polarising beam splitter (PBS1) cube. Two spiral phase plates, SPP1 and SPP2 are used to convert Gaussian beam into optical vortices (LG beams) of order, l = 1 and l = 2, respectively, at conversion efficiency >95%. Due to limited availability of SPPs producing vortices of order l > 2, we have used a vortex-doubler setup21 comprised of a polarizing beam splitter cube (PBS 2), quarter-wave plate (λ∕4) and dielectric coated mirror, M1, with high reflectivity at 405 nm. The working principle of the vortex doubler21 can be understood as follows. The Gaussian beam in horizontally polarization passes through the PBS2. In forward pass through the SPP1 the Gaussian beam acquires spiral phase corresponding to vorticity of order l = +1 (say). The λ/4 plate having its axes at 45° to its polarization axis converts the polarization of the beam into left circular polarization. The mirror, M, reverses both the polarization handedness (left circular to right circular) and sign of the vorticity (l = +1 to −1) of the reflected beam. The right circularly polarized beam on return pass through the λ∕4 plate gets converted into vertical polarization. To the return beam (l = −1), the direction of phase variation of the SPP1 is opposite to that of the forward pass. Therefore, the return beam acquires additional spiral phase resulting total vorticity, l = −2, twice the phase winding of the SPP placed inside. Since the return beam have vertical polarization, it gets reflected by the PBS2. Using different combinations of SPP1 and SPP2, placed inside and outside of the vortex-doubler we have generated optical vortices of orders (topological charges) up to l = 6. An antireflection coated 1” diameter axicon made of BK-7 glass having apex angle 178° is used to convert the vortex beam of order l into BG beam of the same order. As shown in Fig. 1(b), the Fourier transforming lens (f = 200 mm) placed before the axicon with a separation of f-D (D is the distance of the axicon from Fourier plane) produces the perfect vortices (Fig. 1c) at its back focal plane. To measure the change in the vortex radius we have placed the CCD camera (SP620U, Ophir) at the back focal plane of the Fourier lens and varied the position of the axicon. A 5 mm long and 4 × 5 mm aperture, BaB2O4 (BBO) is used as the nonlinear crystal for down conversion of the pump beam (Fig. 1d). The crystal is cut at θ = 29.9°, internal angle with the normal incidence, for type-I (e → o + o) non-collinear phase-matching to produce degenerate signal and idler photons at 810 nm at an angle 3° with respect the pump beam. Due to the circular symmetry, the photons are generated in a cone of apex angle 6° and the photons of each pair are situated in diametrically opposite points. A second lens, f = 50 mm Fourier transforms the generated SPDC ring (Fig. 1e) which is recorded using electron multiplying CCD (EMCCD, Andor-iXon Ultra 897) after filtering the pump photon using an interference filter, IF of 10 nm bandwidth centred at 810 nm. The EMCCD has 512 × 512 pixels with pixel size of 16 micron. To suppress background noise the EMCCD was operated at −80 °C. We have taken images by accumulating 20 frames exposure time of 0.5 s. The λ/2 placed after the mirror M is to adjust the polarization of the input beam depending on the crystal orientation for perfect phase matching.
Additional Information
How to cite this article: Jabir, M. V. et al. Generation of “perfect” vortex of variable size and its effect in angular spectrum of the down-converted photons. Sci. Rep. 6, 21877; doi: 10.1038/srep21877 (2016).
References
Burnham, D. & Weinberg, D. Observation of Simultaneity in Parametric Production of Optical Photon Pairsm, Phys. Rev. Lett. 25, 84–87 (1970).
Hong, C. & Mandel, L. Theory of parametric frequency down conversion of light, Phys. Rev. A 31, 2409–2418 (1985).
Kok, P., Nemoto, K., Ralph, T. C., Dowling, J. P. & Milburn, G. J. Linear optical quantum computing with photonic qubits, Rev. Mod. Phys. 79, 135–174 (2007).
Edgar, M. P. et al. Imaging high-dimensional spatial entanglement with a camera, Nat. Commun. 3, 1–6 (2012).
Mair, A., Vaziri, A., Weihs, G. & Zeilinger, A. Entanglement of the orbital angular momentum states of photons, Nature 412(6844), 313–316 (2001).
Ramírez-Alarcón, Cruz-Ramírez, R., H. & U’Ren, A. B. Crystal length effects on the angular spectrum of spontaneous parametric down conversion photon pairs, Laser Phys. 23(5), 055204 (2013).
Vicuna-Hernandez, V., Cruz-Ramırez, H., Ramırez-Alarcon, R. & U’Ren, A. B. Classical to quantum transfer of optical vortices, Opt. Express 22, 020027 (2014).
Prabhakar, S. et al. Spatial distribution of spontaneous parametric down-converted photons for higher order optical vortices, Opt. Commun. 326, 64–69 (2014).
Reddy, S. G. et al. Divergence of optical vortex beams, Applied Opt. 54, 6690–6693 (2015).
Reddy, S. G., Prabhakar, S., Kumar, A., Banerji, J. & Singh, R. P. Higher order optical vortices and formation of speckles, Opt. Lett. 39, 4364–4367 (2014).
Ostrovsky, A. S., Rickenstorff-Parrao, C. & Arrizón, V. Generation of the “perfect” optical vortex using a liquid-crystal spatial light modulator, Opt. Lett. 38, 534–536 (2013).
Chen, M., Mazilu, M., Arita, Y., Wright, E. M. & Dholakia, K. Dynamics of micro particles trapped in a perfect vortex beam, Opt. Lett. 38, 4919–4922 (2013)
Vaity, P. & Rusch, L. Perfect vortex beam: Fourier transformation of a Bessel beam, Opt. Lett. 40, 597–600 (2015).
Belanger, P. A. & Rioux, M. Ring pattern of a lens–axicon doublet illuminated by a Gaussian beam, Applied Opt. 17, 1080 (1978).
Arlt, J. & Dholakia, K., Generation of high-order Bessel beams by use of an axicon, Opt. Commun. 177, 297–301 (2000).
Jarutis, V., Pa_skauskas, R. & Stabinis, A. Focusing of Laguerre-Gaussian beams by axicon, Opt. Commun. 184, 105–112 (2000).
Rickenstorff, C., García-García, J., Martínez, A. S., Ostrovsky, A. S. & Arrizón, V. Generation of the “Perfect” Vortex for Optical Trapping, Frontiers in Optics, JW3A.34 (2013).
Grier, D. G. A revolution in optical manipulation, Nature 424, 810 (2003).
Osorio, C. I., Terriza, G. M., Font, B. G. & Torres, J P. Azimuthal distinguishability of entangled photons generated in spontaneous parametric down-conversion, Opt. Express 15, 14636 (2007).
Goodman, J. W. Introduction to Fourier Optics (third edition) 104–108 (McGraw-Hill Series, 2007).
Apurv Chaitanya, N., Aadhi, A., Jabir, M. V. & Samanta, G. K. Frequency-doubling characteristics of high-power, ultrafast vortex beams, Opt. Lett. 40, 2614–2617 (2015).
Brzobohatý, O., Cižmár,T. & Zemánek, P. High quality quasi-Bessel beam generated by round-tip axicon, Opt. Express 16, 12688–12700 (2008).
Terizza, G. M., Torres, J. P. & Torner, L. Twisted photons, Nat. Phys. 3, 305–310 (2007).
Author information
Authors and Affiliations
Contributions
M.J., N.C. and A.A. developed the theoretical model. M.J. performed the experimental measurements and data analysis. G.S. developed the ideas and lead the project. All authors contributed to the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Jabir, M., Apurv Chaitanya, N., Aadhi, A. et al. Generation of “perfect” vortex of variable size and its effect in angular spectrum of the down-converted photons. Sci Rep 6, 21877 (2016). https://doi.org/10.1038/srep21877
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep21877
- Springer Nature Limited