Abstract
In this paper the influence of process parameters and fluence on mechanical properties of maraging steel in Selective Laser Melting (SLM) is studied. The results of the present work show that there exists a steady region of process parameters where fluence conveys all the information required to describe and predict density and tensile properties. We also show that in this region of the parameters, the choice of process parameters can be carried out considering other optimality criteria such as productivity, rather than maximization of density. To pursue this objective, a V-Alphabetical optimal design with fixed fluence levels was specifically designed for the experimentation. The used fluence levels and the corresponding process parameter combinations were tested on an industrial SLM system. To compare the informative content of fluence and the process parameters, two regression equation were estimated from experimental results for part density and tensile properties. The comparison of the regression models showed that the predictive ability of fluence and process parameters in the steady region is the same, however fluence allowed to obtain a higher precision. In conclusion, based on the experimental conditions studied, new process parameters are suggested using a productivity-based criteria.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Herzog, D., Seyda, V., Wycisk, E., and Emmelmann, C., “Additive Manufacturing of Metals,” Acta Materialia, Vol. 117, pp. 371–392, 2016.
O’Regan, P., Prickett, P., Setchi, R., Hankins, G., and Jones, N., “Metal based Additive Layer Manufacturing: Variations, Correlations and Process Control,” Procedia Computer Science, Vol. 96, pp. 216–224, 2016.
Aboulkhair, N. T., Everitt, N. M., Ashcroft, I., and Tuck, C., “Reducing Porosity in AlSi10Mg Parts Processed by Selective Laser Melting,” Additive Manufacturing, Vol. 1, pp. 77–86, 2014.
Gong, H., Rafi, K., Starr, T., and Stucker, B., “The Effects of Processing Parameters on Defect Regularity in Ti-6Al-4V Parts Fabricated by Selective Laser Melting and Electron Beam Melting,” Proc. of 24th Annual International Solid Freeform Fabrication Symposium -An Additive Manufacturing Conference, pp. 12–14, 2013.
Hu, Z., Zhu, H., Zhang, H., and Zeng, X., “Experimental Investigation on Selective Laser Melting of 17-4PH Stainless Steel,” Optics and Laser Technology, Vol. 87, pp. 17–25, 2017.
Demir, A. G., Colombo, P., and Previtali, B., “From pulsed to Continuous Wave Emission in SLM with Contemporary Fiber Laser Sources: Effect of Temporal and Spatial Pulse Overlap in Part Quality,” The International Journal of Advanced Manufacturing Technology, Vol. 91, Nos. 5–8, pp. 2701–2714, 2017.
Kaden, L., Matthäus, G., Ullsperger, T., Engelhardt, H., Rettenmayr, M., Tünnermann, A., and Nolte, S., “Selective Laser Melting of Copper Using Ultrashort Laser Pulses,” Applied Physics A, Vol. 123, No. 9, p. 596, 2017.
Maskery, I., Aboulkhair, N. T., Aremu, A. O., Tuck, C. J., Ashcroft, I. A., et al., “A Mechanical Property Evaluation of Graded Density Al-Si10-Mg Lattice Structures Manufactured by Selective Laser Melting,” Materials Science and Engineering: A, Vol. 670, pp. 264–274, 2016.
Zhang, Y., Liu, T., Ren, H., Maskery, I., and Ashcroft, I., “Dynamic Compressive Response of Additively Manufactured AlSi10Mg Alloy Hierarchical Honeycomb Structures,” Composite Structures, Vol. 195, pp. 45–59, 2018.
Demir, A. G. and Previtali, B., “Additive Manufacturing of Cardiovascular CoCr Stents by Selective Laser Melting,” Materials and Design, Vol. 119, pp. 338–350, 2017.
Cherry, J. A., Davies, H. M., Mehmood, S., Lavery, N. P., Brown, S. G. R., and Sienz, J., “Investigation into the Effect of Process Parameters on Microstructural and Physical Properties of 316L Stainless Steel Parts by Selective Laser Melting,” The International Journal of Advanced Manufacturing Technology, Vol. 76, Nos. 5–8, pp. 869–879, 2015.
Alfaify, A. Y., Hughes, J., and Ridgway, K., “Critical Evaluation of the Pulsed Selective Laser Melting Process When Fabricating Ti64 Parts Using a Range of Particle Size Distributions,” Additive Manufacturing, Vol. 19, pp. 197–204, 2018.
Morgan, R., Sutcliffe, C., and O'neill, W., “Density Analysis of Direct Metal Laser Re-Melted 316L Stainless Steel Cubic Primitives,” Journal of Materials Science, Vol. 39, No. 4, pp. 1195–1205, 2004.
Meier, H. and Haberland, C., “Experimental Studies on Selective Laser Melting of Metallic Parts,” Materialwissenschaft und Werkstofftechnik, Vol. 39, No. 9, pp. 665–670, 2008.
Simchi, A., “The Role of Particle Size on the Laser Sintering of Iron Powder,” Metallurgical and Materials Transactions B, Vol. 35, No. 5, pp. 937–948, 2004.
Wang, D., Liu, Y., Yang, Y., and Xiao, D., “Theoretical and Experimental Study on Surface Roughness of 316l Stainless Steel Metal Parts Obtained through Selective Laser Melting,” Rapid Prototyping Journal, Vol. 22, No. 4, pp. 706–716, 2016.
Kuo, C., Su, C., and Chiang, A., “Parametric Optimization of Density and Dimensions in Three-Dimensional Printing of Ti-6Al-4V Powders on Titanium Plates Using Selective Laser Melting,” International Journal of Precision Engineering and Manufacturing, Vol. 18, No. 11, pp. 1609–1618, 2017.
Kobryn, P. A., Moore, E. H., and Semiatin, S. L., “The Effect of Laser Power and Traverse Speed on Microstructure, Porosity, and Build Height in Laser-Deposited Ti-6Al-4V,” Scripta Materialia, Vol. 4, No. 43, pp. 299–305, 2000.
Antony, K., Arivazhagan, N., and Senthilkumaran, K., “Numerical and Experimental Investigations on Laser Melting of Stainless Steel 316L Metal Powders,” Journal of Manufacturing Processes, Vol. 16, No. 3, pp. 345–355, 2014.
Hrabe, N. and Quinn, T., “Effects of Processing on Microstructure and Mechanical Properties of a Titanium Alloy (Ti-6Al-4V) Fabricated Using Electron Beam Melting (EBM), Part 2: Energy Input, Orientation, and Location,” Materials Science and Engineering: A, Vol. 573, pp. 271–277, 2013.
Spierings, A. B. and Levy, G., “Comparison of Density of Stainless Steel 316L Parts Produced with Selective Laser Melting Using Different Powder Grades,” Proc. of the Annual International Solid Freeform Fabrication Symposium, pp. 342–353, 2009.
Gu, H., Gong, H., Pal, D., Rafi, K., Starr, T., and Stucker, B., “Influences of Energy Density on Porosity and Microstructure of Selective Laser Melted 17-4PH Stainless Steel,” Proc. of 2013 Solid Freeform Fabrication Symposium, 2013.
Prashanth, K., Scudino, S., Maity, T., Das, J., and Eckert, J., “Is the Energy Density a Reliable Parameter for Materials Synthesis by Selective Laser Melting?” Materials Research Letters, Vol. 5, No. 6, pp. 386–390, 2017.
Bertoli, U. S., Wolfer, A. J., Matthews, M. J., Delplanque, J.-P. R., and Schoenung, J. M., “On the Limitations of Volumetric Energy Density as a Design Parameter for Selective Laser Melting,” Materials & Design, Vol. 113, pp. 331–340, 2017.
Montgomery, D. C., “Design and Analysis of Experiments,” John Wiley & Sons, 2017.
Spierings, A. B., Schneider, M., and Eggenberger, R., “Comparison of Density Measurement Techniques for Additive Manufactured Metallic Parts,” Rapid Prototyping Journal, Vol. 17, No. 5, pp. 380–386, 2011.
Yasa, E., Kempen, K., Kruth, J., Thijs, L., and Van Humbeeck, J., “Microstructure and Mechanical Properties of Maraging Steel 300 after Selective Laser Melting,” Proc. of Solid Freeform Fabrication Symposium, pp. 383–396, 2010.
Suryawanshi, J., Prashanth, K., and Ramamurty, U., “Tensile, Fracture, and Fatigue Crack Growth Properties of a 3D Printed Maraging Steel through Selective Laser Melting,” Journal of Alloys and Compounds, Vol. 725, pp. 355–364, 2017.
Draper, N. R. and Smith, H., “Applied Regression Analysis,” John Wiley & Sons, 2014.
Author information
Authors and Affiliations
Corresponding author
Additional information
This article is published with open access at Springerlink.com
Stefania Cacace Ph.D. candidate in the Department of Mechanical Engineering, Politecnico di Milano. Her research interest are Additive Manufacturing, design of the experiments and process optimization.
Quirico Semeraro Professor in the Department of Mechanical Engineering, Politecnico di Milano. His research interest are advanced and traditional machining, industrial statistics, design of the experiments.
Rights and permissions
Open Access The article published in this journal is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, andindicate if changes were made.
About this article
Cite this article
Cacace, S., Semeraro, Q. About Fluence and Process Parameters on Maraging Steel Processed by Selective Laser Melting: Do They Convey the Same Information?. Int. J. Precis. Eng. Manuf. 19, 1873–1884 (2018). https://doi.org/10.1007/s12541-018-0204-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-018-0204-y