Abstract
As evidence for the devastating impacts of air pollution on human health continues to increase, improving urban air quality has become one of the most pressing tasks facing policy makers world-wide. Increasingly, and very often on the basis of conflicting and/or weak evidence, the introduction of green infrastructure (GI) is seen as a win–win solution to urban air pollution, reducing ground-level concentrations without imposing restrictions on traffic and other polluting activities. The impact of GI on air quality is highly context dependent, with models suggesting that GI can improve urban air quality in some situations, but be ineffective or even detrimental in others. Here we set out a novel conceptual framework explaining how and where GI can improve air quality, and offer six specific policy interventions, underpinned by research, that will always allow GI to improve air quality. We call GI with unambiguous benefits for air quality GI4AQ. However, GI4AQ will always be a third-order option for mitigating air pollution, after reducing emissions and extending the distance between sources and receptors.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction: Urban air quality and green infrastructure
More than half of the world’s population currently live in urban areas, most of which have outdoor air quality that fails to meet World Health Organisation guidelines for healthy living. Air pollution, principally caused by nitrogen dioxide (NO2) and fine particles of aerodynamic diameter less that 2.5 µm (PM2.5), is now the leading environmental cause of mortality world-wide, causing ~ 3 million premature deaths a year, twice the number due to road traffic accidents (World Health Organisation 2016). While reducing pollutant emissions is always the most direct way to improve urban air quality, authorities world-wide have, with few exceptions, struggled to provide adequate air quality improvements through emission control strategies alone. Policy makers are increasingly turning to complementary methods of reducing human exposure to air pollutants as cities expand, the number of motor vehicles grows (globally from < 0.1 × 109 in 1960 to > 1 × 109 in 2017), and distances driven increase. The relative growth in diesel vehicle numbers, many of which are not compliant with emission regulations (Schiermeier 2015), is an important additional adverse factor in some countries, including the UK.
One increasingly promoted method for air pollution mitigation is the use of green infrastructure (GI): street and park trees, green walls, green roofs (Berardi et al. 2013), and other means of introducing vegetation into the urban landscape (Beatley 2016), on the basis that pollutants deposit more efficiently onto vegetation than onto smoother, impervious, artificial surfaces (Fowler et al. 2009; Nowak et al. 2013; Neft et al. 2016). However, the empirical evidence for the effectiveness of GI for air quality is weak. Without a method to systematically assess GI impacts on urban air, it will remain difficult for researchers and practitioners to determine how and where GI can improve air quality. In offering such a method here, we recognise that known modelling deficiencies and lack of ground-truthing field observations limit the precise quantitative assessment of specific GI interventions. Whereas previous reviews of this topic have focussed on one aspect of the problem (e.g. removal of particles; Janhäll 2015) or have been rather unselective (e.g. Abhijith et al. 2017), here we critically appraise the evidence for the effectiveness of GI in a conceptual framework and offer six specific policy interventions that can only benefit air quality.
GI is part of the urban canopy, set within, and contributing to, its heterogeneity. The character of the urban canyon adds complexity but also offers opportunities to identify sites where GI will have unambiguous benefits for air quality (which we call GI4AQ). Below, we use ‘canopy’ to refer to the volume-filling effects of buildings and trees; we use ‘crown’ when discussing individual tree tops. Metrics describing stem or stand densities do not adequately define the urban tree canopy because of differing tree management methods (e.g. pollarding). Planar cover, while an undoubtedly useful measure (e.g. as used in the i-Tree Canopy model), leaves the vitally important vertical dimension unconstrained, and neither stem count nor tree-crown cover situates GI three-dimensionally in the urban canyon. Here, we use three underpinning urban canopy-related axioms: that GI will affect air quality most significantly when it (i) fills canopy gaps and edges to alter flow (Oke 1988; Ng and Chau 2012), (ii) alters mean aerodynamic roughness (Barnes et al. 2014; Jeanjean et al. 2015) or (iii) increases the absorbency of surfaces adjacent to polluted air held within the urban canopy (Pugh et al. 2012).
Ground-level concentrations of urban air pollutants are a complex function of emissions, dispersion (stirring and mixing), deposition and chemistry. Much of this complexity is due to the spatial pattern of the urban canopy (Ratti et al. 2006; Abhijith et al. 2017), within which people are exposed to polluted air. The urban canopy occupies near-surface volume (Henderson et al. 2016), interacting with the air flow (Oke 1988). Stirring of parcels of air stretches and folds them, producing irregular blobs and filaments of relatively undiluted emissions interleaved with cleaner air, and mixing dilutes emissions by intermingling them with cleaner air at the molecular scale (Prather and Jaffe 1990; Tan et al. 1998). For urban land-classes dominated by transport corridors (Owen et al. 2006), the landscape is more open with fewer buildings and the canopy largely comprises vegetation (Choi et al. 2014; Abhijith et al. 2017).
Despite the complexities of how urban form impacts the atmospheric concentrations of pollutants, developing a framework around the urban-canopy axioms above can guide policy makers on how and where GI can be used to improve air quality—GI4AQ—and where GI is unhelpful or even detrimental to air quality. Inserting or removing GI with the intention of improving air quality must be considered in the context of other possible co-benefits and costs. For example, urban trees provide habitats that enhance biodiversity, provide shade and other micro-climate services (Livesley et al. 2016; Salmond et al. 2016) and, to a minor extent, sequester carbon dioxide from the atmosphere (Nowak and Crane 2002). Like all urban infrastructure, GI systems, from sophisticated vertical forests (Moeller 2015) to shrubs in planters, require proper installation and regular long-term maintenance to prevent damage to buildings, roads and pavements (Trees, Design and Action Group, TDAG 2012, 2014). Planning with GI should include scenario-based ‘futures thinking’ to ensure long-term efficacy (Lombardi et al. 2012; Hale et al. 2015). For example, trees in street canyons which currently reduce dispersion of traffic pollutants (see below) may be less of a concern in the future when electric or hydrogen vehicles will cause much less street-level pollution emissions (Jacobson et al. 2005). Likewise, in the past, when major pollution sources were mainly situated above roof level, the impact of street trees on pollutant dispersion within the street canyon was not a significant concern.
A useful conceptualisation of air pollution mitigation in urban areas is “Reduce–Extend–Protect”. Reducing emissions is always the most effective method of reducing human exposure to pollutants and should always be the primary focus of mitigation action. GI does not play any explicit role in this. Extending the distance between sources and receptors, enhancing dilution and dispersion and hence reducing concentrations at a given receptor, is usually the second-best method of reducing exposure. This may be done by physically extending the distance between, for example, road vehicles and pedestrians, or by placing barriers to flow between sources and receptors. GI can act in this role, for example when hedges are used to separate traffic and pedestrians, virtually extending the distance between source and receptor. Protecting receptors involves introducing direct interventions that reduce concentrations at the receptor site, and here GI can be used in several configurations, as discussed below. This will normally be the third-best mitigation option.
Dispersion of air pollutants
Trees and hedges provide semi-permeable obstacles to the flow of air (Bradley and Mulhearn 1983; Raine and Stevenson 1977; Tiwary et al. 2005; Gromke et al. 2016; Tong et al. 2016), deflecting stream-lines, introducing turbulence and increasing dilution and hence virtually extending the distance between source and receptor. Several structural factors, such as plant height and morphology, affect the way vegetation interacts with flow, and can be considered design parameters (Baldauf 2017) for GI4AQ. Dense vegetation acts almost as a bluff body, with negligible permeating flow and a region of recirculation behind the vegetation (Tiwary et al. 2005). For crown porosities above ~ 50%, no recirculating region forms behind the obstacle (Baltaxe 1967; Bradley and Mulhearn 1983). Porosities of common urban GI4AQ are listed in a recent review (Abhijith et al. 2017).
Regions of accelerating and decelerating air stir pollutants into filamentary patches of higher and lower concentrations (Gromke and Blocken 2015) (Fig. 1). Resolving these spatial variations at the street scale requires resource-intensive computational fluid dynamics (CFD) modelling, supported by site-specific crown and canopy measurements (Hofman et al. 2016). The modelled aerodynamic effect of street trees for two main roads in London, for example, was quasi-two dimensional, and reductions in the average concentrations in the street canyons were negligible (1%) (Jeanjean et al. 2017a, b). Under other circumstances, canopy-induced turbulence in the model led to three-dimensional stirring and mixing, reducing average ground-level concentrations (Barnes et al. 2014). Modelling using a remotely sensed inventory of tree-top pattern calculated a median reduction of 8% in ground-level concentrations of PM2.5 across a specific city centre due to the dispersive effect of the trees present (Jeanjean et al. 2015). In contrast, a recent summary reported increases of between 0 and 96% in modelled average street canyon pollutant concentrations due to the introduction of trees (Abhijith et al. 2017), highlighting both the uncertainties in current models and the need for caution when introducing trees to street canyons.
Contiguous and dense tree crowns can effectively separate the air below the canopy from that above (Gromke and Blocken 2015). A reversal of flow at 2 m above street level for street trees spaced at 25-m intervals (Moradpour et al. 2017) dramatically exemplifies such behaviour in models. In parks, traffic-free plazas, and other pedestrian areas without significant ground-level anthropogenic pollution sources, but with dense vegetation canopies, the below-canopy air will always be cleaner than that above the canopy due to enhanced deposition of pollution onto the vegetation as the air percolates through the canopy (see below). However, when canopy closure occurs in a street canyon containing ground-level sources of pollution, pollutants may be trapped, leading to increased ground-level concentrations (Vos et al. 2013; Abhijith et al. 2017). In such situations, local emission controls should be implemented to reduce or remove the ground-level pollution source. When emissions cannot be adequately reduced, it is necessary to identify which elements of the urban canopy are inhibiting vertical mixing and, hence, what modifications to the canopy (including tree crowns) can be made to improve ventilation and so improve ground-level air quality (GI4AQ Policy Intervention 1, see Table 1). CFD studies provide the only quantitative method currently available to quantify ventilation, but many such studies do not capture the intermittency of turbulent flow and all lack field observations for model evaluation.
Dispersion will always ultimately transfer pollutants down concentration gradients into the cleaner atmosphere or towards absorptive surfaces. As pollutants move from their source, turbulence dilutes the plume by mixing in cleaner air, as recognised in operational air quality models (e.g. Heist et al. 2013; Stocker et al. 2013; Design Manual for Roads and Bridges 2017) and more sophisticated simulations (Tong et al. 2016). The introduction of linear obstacles (e.g. hedges or fences) between source and receptor zones displaces the pollutant plume upwards (Bowker et al. 2007), extending the effective path-length of air from source to receptor, and may also promote dilution by enhancing turbulence. Hence hedges and fences can reduce concentrations along pavements, side-walks and other pedestrian areas adjacent to traffic (Gallagher et al. 2015; Gromke et al. 2016; Abhijith et al. 2017) (Fig. 2). Decreases in pollution concentrations of 20–70% (average 52%) behind a 1-m-high impermeable barrier in an open setting have been modelled (King et al. 2009). The effect of barriers on concentrations is complicated by street-scale circulations within a street canyon (McNabola et al. 2009; Gromke et al. 2016; Abhijith et al. 2017).
As the porosity of the barrier increases, the effective path-length decreases (Fig. 2) but the opportunity for removal of particles by deposition increases (Tong et al. 2016). The collection efficiency for a 2.2-m-high, 1.6-m-wide porous hawthorn hedge was measured at ~ 1% for particles < 2.5 µm diameter, increasing to ~ 30% for particles of 15 µm diameter. These results could be reproduced adequately using 2D modelling with appropriate treatment of drag and particle collection (Tiwary et al. 2005; Guo and Maghirang 2012). In general, linear barriers are helpful in aiding dispersion and deposition and hedges (and fences) may therefore offer some protection to pedestrians (GI4AQ Policy Intervention 2). Such obstacles need not be GI (Gallagher et al. 2015), although porous GI or a mix of hard barrier and GI (Tong et al. 2016) would offer co-benefits through enhanced deposition of both large (diameter, d > 1 µm) and small (d < 100 nm) particles (Neft et al. 2016).
Deposition of air pollutants
In contrast to dispersion, the deposition of a pollutant to a surface results in permanent loss from the atmosphere, and hence a reduction in total atmospheric loading. Wet deposition is associated with precipitation and proceeds at the same rate to all surfaces (Sehmel 1980; Fowler et al. 2004). However, the rate of dry deposition is highly dependent on the macroscopic characteristics of the surface, i.e. available surface area (Padro 1996; Fowler et al. 2004; Gröte et al. 2016) and surface aerodynamic roughness (Sehmel 1980), and GI can potentially protect against air pollution by enhancing the deposition rates of pollutants and hence reduce concentrations of pollutants in the vicinity of receptors. The mix of plant species and size used in GI, and their spatial relationship to the built environment, will determine these deposition parameters and, hence, determine the maximum potential rate of pollutant dry deposition. Particle deposition velocities as high as 11 mm s−1 have been measured to urban trees, compared with around 3 mm s−1 to adjacent grass, and dry deposition has been estimated to account for ~ 70% of total deposition to urban trees compared with ~ 25% to grass (Fowler et al. 2004).
Vegetation with higher surface area, greater rates of transpiration, and longer in-leaf periods result in the greatest enhancements in dry deposition over that to bare surfaces (Padro 1996; Branford et al. 2004; Nowak et al. 2006; Cabaraban et al. 2013; Gröte et al. 2016). For this reason, the selection of species is critical in determining the increased pollutant removal achieved through the addition of GI to the built environment. For example, the available surface area of deciduous broad-leaved trees can reach up to 6 m2 per m2 of bare ground (Nowak et al. 2006), 20% more than evergreen needle-leaf trees (van den Hurk et al. 2003). Leaf and plant morphology also contribute to the overall rate of dry deposition to different vegetation species and should be considered in combination with surface area (Gröte et al. 2016).
On-line tools have been developed to assist in species selection (e.g. i-Trees Species Selector 2017 and the derivative European Specifind 2017) but these are of necessity black-box database search instruments giving a list of potential species that acts as a starting point for refinement against other considerations. These on-line tools usually assume optimal physiological behaviour of the GI, but poor soils, high temperatures exacerbated by the urban heat island effect and limited water availability often combine to reduce leaf area and transpiration, reducing deposition rates to well below that for unstressed vegetation (Calfapietra et al. 2015). Effective management of GI (Lu et al. 2010; Young 2011; Pincetl et al. 2013), e.g. to avoid water stress, is therefore essential to ensure its long-term health and functioning and to maximise deposition rates (GI4AQ Policy Intervention 3).
In addition to plant morphology, the characteristics of the canopy play an important role in modifying surface roughness and turbulence. There is the potential to design heterogeneity into the urban canopy to exploit edge effects and maximise deposition. Particle removal by dense forest canopies has been observed to be over 30% higher than to adjacent open heathland with the greatest increases (over 50%) occurring at the forest edge (Branford et al. 2004).
As the rate of dry deposition is proportional to the local concentration of the pollutant (for a given surface and wind flow), GI is most effective at improving air quality in locations where pollutant concentrations are highest (Nowak et al. 2006; Morani et al. 2011; Cabaraban et al. 2013) and where residence times are longest (Pugh et al. 2012). Where GI acts on large volumes of air, for example in the case of green roofs upwind of street canyons, where there will not be a shallow boundary layer or constrained volume of air above the roof surface, the potential to reduce atmospheric concentrations of pollutants is very limited (typically < 1%) (Donovan et al. 2005; Pugh et al. 2012). The capital and maintenance cost of green roofs is therefore likely to be a very poor investment for air quality mitigation.
Measuring or modelling the potential mass of pollution deposited for given air concentrations can make the GI4AQ effect appear to be significant (Nowak et al. 2006; Speak et al. 2012; Berardi et al. 2013), but calculations or measurements of deposition should be combined with modelling of resultant changes in atmospheric concentrations to properly estimate the actual air quality benefits of GI4AQ (Hofman et al. 2016). Recent developments in the application of eddy covariance methods for measuring deposition rates of pollutants offer the possibility of model validation, although probably at only a relatively large (urban park) scale (Guidolotti et al. 2017). In fact, increasing deposition rates will often not result in discernible reductions in atmospheric concentrations, but where GI acts on relatively small volumes of air and ventilation rates are relatively low, models predict that the effects on ground-level air quality can be very large (Pugh et al. 2012). For this reason, the introduction of large areas of green walls in street canyons may be particularly effective at improving ground-level air quality (GI4AQ Policy Intervention 4).
Creating “green oases”, i.e. slowly ventilated areas containing or surrounded by GI but with no internal anthropogenic pollutant sources, will always lead to an improvement in air quality. Green oases can vary in scale from a bench or other small areas surrounded by relatively tall GI, e.g. hedges, up to pedestrianised and verdant street canyons, plazas or courtyards, or even to a park covered in an extensive vegetated trellis roof. In these cases, the amount of GI present should be maximised (GI4AQ Policy Intervention 5).
Negative impacts of trees on air quality through effects on atmospheric chemistry
All plants synthesise reactive volatile organic compounds (biogenic VOCs) and emit them to the atmosphere. The single most important bVOC by emitted mass and reactivity is isoprene (C5H8, 2-methyl-1,3-butadiene) but several tens of other bVOCs have significant effects in the atmosphere (Atkinson and Arey 2003; Guenther et al. 2012). As well as these constitutive emissions, biotic and abiotic stresses may induce the production of many other compounds (Hatanaka 1993). For an overview of bVOC synthesis pathways, their biological functions and their emissions and effects in the atmosphere, see Laothawornkitkul et al. (2009).
Although the vast majority of VOCs emitted globally are biogenic in origin (Guenther et al. 1995, 2012), emissions from anthropogenic sources are relatively much more important in urban areas. Nevertheless, isoprene, which has both biogenic and anthropogenic sources, may still be important in urban areas, especially in summer (e.g. Wang et al. 2013), even in temperate cities such as London (Langford et al. 2010).
In the context of urban GI, the most significant bVOC emissions are those from trees, since in almost all urban situations trees will contribute the majority of leaf biomass. Constitutive emissions vary considerably in chemical composition between tree species. Urban areas may contain a large number of tree species, as native species will often be augmented by a wide range of exotics, especially in parks and gardens, all with differing bVOC emission profiles and rates. For example, 126 different species of mature trees have been recorded in London (Treeconomics 2015) and 170 in Beijing (Yang et al. 2005).
bVOCs take part in chemical reactions in the atmosphere that can lead to the formation of ozone (MacKenzie et al. 1991; Chameides et al. 1988; Atkinson and Arey 2003; Donovan et al. 2005; Calfapietra et al. 2013) and organic aerosol particles (Carlton et al. 2009; Hallquist et al. 2009; Mentel et al. 2009; Wyche et al. 2014), both of which are important secondary air pollutants. Since it takes several hours before these chemical reactions generate high pollutant concentrations of ozone or particles, the precise location of bVOC-emitting GI within the urban canopy is not important. This is in contrast to the dispersion and deposition effects of GI, which are highly location-specific. From a policy perspective then, when GI is being implemented for pollution control by dispersion and deposition, the negative effects on secondary air pollution (i.e. ozone and particle formation) can be considered separately, at the urban air-shed, rather than the local, scale.
bVOC emissions from a typical urban tree population contribute on the order of 10% to ozone concentrations within and downwind of large city-regions (MacKenzie et al. 1991; Chameides et al. 1988; Donovan et al. 2005; Calfapietra et al. 2013). Unfortunately, there is no easy way to reliably predict whether or not a given tree species emits a particular bVOC, or at what specific rate. Notwithstanding this, if the total urban tree population is to be altered significantly, e.g. by more than ~ 10%, care should be given to the choice of tree species used, in order to not exacerbate the bVOC emission rates at the urban air-shed scale (GI4AQ Policy Intervention 6). Several (incomplete and largely uncritical) bVOC emission databases (http://www.es.lancs.ac.uk/cnhgroup/iso-emissions.pdf; Keenan et al. 2009; http://bai.acom.ucar.edu/Data/BVOC) may be referred to when selecting tree species for planting, based on their likely bVOC emissions. A more sophisticated assessment might weigh deposition benefits against secondary pollutant formation potentials for individual tree species, to generate, for example, an “Urban Tree Air Quality Score” (Donovan et al. 2005).
Two policy-relevant implications arise from the fact that trees take decades to mature, with bVOC emissions increasing as their leaf area increases over time. First, in the next few decades there is the possibility that urban transport will become less polluting than currently, leading to lower secondary pollutant formation. Ozone isopleths, or ‘Sillman plots’ (1999), which relate ozone pollution to NOx and VOC emissions, can be used to estimate the emission reductions from traffic needed to ensure that any additional bVOC emissions resulting from tree planting do not produce additional ozone. Secondly, climate change will lead to increased temperatures, especially in urban areas (Fowler et al. 2008; Estrada et al. 2017), increasing bVOC emissions and therefore exacerbating ozone pollution events (Yang et al. 2008), enhancing the relevance of Policy Intervention 6.
Policy guidance and conclusions
Numerous modelling studies suggest it is possible to make GI interventions that will improve urban air quality, but there is little unequivocal empirical evidence or validation to support this, although this may change as new measurement technologies become available (e.g. Guidolotti et al. 2017). In situations where pollutant concentrations change rapidly in space and time (e.g. near to roads), measuring small changes in concentrations and attributing these to the introduction of GI is almost impossible. Laboratory-scale experiments have limited utility because deposition and dispersion are very tightly coupled to the three-dimensional urban form and the synoptic-scale flow, while designing field-scale experiments involving GI with adequate controls is difficult, if not impossible. Policy makers must therefore make decisions on GI largely based on model predictions rather than empirical evidence. To aid this, we have identified six GI4AQ Policy Interventions, deduced from an understanding of the processes operating in the near-surface urban air volume (Table 1). All these interventions are risk-free in the sense they can only benefit ground-level air quality, although the effectiveness of specific interventions will vary from the insignificant to the highly significant. Effectiveness may be hard to determine empirically. This is in contrast to other possible actions involving GI that may be detrimental to air quality (e.g. introducing trees into a street canyon, which may increase canopy closure and reduce ventilation rates), or those that may have no discernible effects on air quality (e.g. building green roofs).
A common fallacy concerning urban GI is that increasing the amount of vegetation reduces ground-level pollutant concentrations linearly (i.e. that doubling leaf area will half pollutant concentrations). The vegetation deposition sink is at a distance from the pollutant emission source, so atmospheric concentrations will be always a non-zero, positive-definite, balance of emissions, advection, deposition, and reaction. Not accounting for other terms in the budget leads to over-estimation of the efficacy of green roofs and other forms of GI on air quality, to the detriment of rational decision making.
Figure 3 is a flow chart designed to help policy makers navigate the few critical decisions that determine the suitability of GI4AQ—from a scientific perspective—at all relevant spatial scales, from the smallest urban park to a ‘million trees’ Initiative. The flow chart indicates that some policy decisions (marked by green paths in the figure) may be safely reached by the application of simple rules of thumb and the existing literature. Other decisions require specialist and resource-intensive model simulations of dispersion and/or atmospheric chemistry (red paths in the figure) but may still warrant investigation. GI choices shown in grey will be ineffective for air quality improvement but may, of course, still provide other ecosystem services (Beatley 2016). The flowchart should therefore help to prioritise GI interventions when intended for AQ benefits and indicate which GI investment decisions should be supported by more detailed studies.
GI4AQ can be effective over a range of horizontal and vertical spatial scales, although there are limitations. It may be helpful to consider an intervention in terms of its characteristic horizontal scale and its height-to-width aspect ratio (Fig. 4). When horizontal length scales and aspect ratios are small, residence times are short and there is little opportunity for deposition to become effective. When aspect ratios are large, especially at large horizontal scales, it becomes physically impossible to manufacture the GI4AQ intervention. GI4AQ is effective where deposition can be enhanced by holding air for longer near vegetation. The space domains in which GI4AQ is likely to be effective range in size from a small “green oasis” such as a bench closely surrounded by high hedges to a dense urban woodland.
Green roofs have horizontal scales up to tens of metres and aspect ratios ≪ 1, and so fall in the bottom left-hand corner of Fig. 4. While they enhance the deposition of pollutants from the atmosphere by increasing the available surface area (Yang et al. 2008; Treeconomics 2015), they are unlikely to make an appreciable difference to ground-level pollutant concentrations since they act on the very large volume of air above the urban canopy (Pugh et al. 2012). Vertical forests (e.g. Moeller 2015) have modest horizontal extent and very large aspect ratios but will be ineffective as GI4AQ because they do not produce either a closed canopy or an open top green oasis. In contrast, green walls in street canyons with aspect ratios greater than about unity [log (H/W) > 0] may make appreciable differences to ground-level concentrations (Pugh et al. 2012).
Despite the complexities of modern cities, the conceptual framework outlined above, underpinned by research, allows us to provide guidance to policy makers on where and how GI can benefit urban air quality. When proper consideration of context is made, there are clear and substantive opportunities to employ GI to improve air quality. The framework will also help practitioners and policy makers assess new research on GI and air quality as it becomes available. Properly designed and implemented GI4AQ (Lombardi et al. 2012; Trees, Design and Action Group 2014; Beatley 2016) may help cities meet several of the UN’s Sustainable Development Goals, but poorly designed GI may be ineffective or even detrimental to urban air quality. Importantly, decisions on GI4AQ must be made in the wider context of all the costs and benefits of trees (and other GI) in cities (Daniels et al. 2018), for example as one component of a wider “Urban Tree Score” Framework (Donovan et al. 2005).
Finally, it should be noted that the most direct and sure way to improve urban air quality is by reducing primary pollutant emissions and the focus of air pollution policies should always be on this. As a secondary measure, it is always beneficial simply to extend the distance between sources and receptors at all horizontal scales. Introducing GI4AQ should therefore normally be considered a third-best measure that may, in some situations, help improve urban air quality.
References
Abhijith, K.V., P. Kumar, J. Gallagher, A. McNabola, R. Baldauf, F. Pilla, B. Broderick, S. Di Sabatinoi, and B. Pulvirenti. 2017. Air pollution abatement performances of green infrastructure in open road and built-up street canyon environments—A review. Atmospheric Environment 162: 71–86.
Atkinson, R.A., and J. Arey. 2003. Gas-phase tropospheric chemistry of biogenic volatile organic compounds: A review. Atmospheric Environment 37: S197–S219.
Baldauf, R. 2017. Roadside vegetation design characteristics that can improve local, near-road air quality. Transportation Research Part D Transport and Environment 843: 354–361.
Baltaxe, R. 1967. Air flow patterns in the lee of model windbreaks. Archiv für Meteorologie, Geophysik und Bioklimatologie 15: 287–312.
Barnes, M.J., T. Brade, A.R. MacKenzie, J.D. Whyatt, D.J. Carruthers, J. Stocker, X. Cai, and C.N. Hewitt. 2014. Spatially-varying surface roughness and ground-level air quality in an operational dispersion model. Environmental Pollution 185: 44–51.
Beatley, T. 2016. Handbook of Biophilic City Planning and Design. Washington, DC: Island Press.
Berardi, U., A.H. GhaffarianHoseini, and G. Hoseini. 2013. State-of-the-art analysis of the environmental benefits of green roofs. Journal of Applied Energy 115: 411–428.
Biogenic Volatile Organic Compounds (BVOC) Data. http://bai.acom.ucar.edu/Data/BVOC/. Accessed 1 June 2017.
Biogenic Volatile Organic Compounds (BVOC) Database. http://www.es.lancs.ac.uk/cnhgroup/iso-emissions.pdf. Accessed 1 June 2017.
Bowker, G.E., R. Baldauf, V. Isakov, A. Khlystov, and W. Petersen. 2007. The effects of roadside structures on the transport and dispersion of ultrafine particles from highways. Atmospheric Environment 41: 8128–8139.
Bradley, E.F., and P.J. Mulhearn. 1983. Development of velocity and shear stress distribution in the wake of a porous shelter fence. Journal of Wind Engineering and Industrial Aerodynamics 15: 145–156.
Branford, D., D. Fowler, and M.V. Moghaddam. 2004. Study of aerosol deposition at a wind exposed forest edge using 210Pb and 137Cs soil inventories. Water, Air, and Soil Pollution 157: 107–116.
Cabaraban, M.T.I., C.N. Kroll, S. Hirabayashi, and D.J. Nowak. 2013. Modeling of air pollutant removal by dry deposition to urban trees using a WRF/CMAQ/i-Tree Eco coupled system. Environmental Pollution 176: 123–133.
Calfapietra, C., S. Fares, F. Manes, G. Sgrigna, and F. Loreto. 2013. Role of Biogenic Volatile Organic Compounds (BVOC) emitted by urban trees on ozone concentration in cities: A review. Environmental Pollution 183: 71–80.
Calfapietra, C., J. Peñuelas, and Ü. Niinemets. 2015. Urban plant physiology: Adaptation-mitigation strategies under permanent stress. Trends in Plant Science 20: 72–75.
Carlton, A.G., C. Wiedinmyer, and J.H. Kroll. 2009. A review of Secondary Organic Aerosol (SOA) formation from isoprene. Atmospheric Chemistry and Physics 9: 4987–5005.
Chameides, W.L., R. Linsay, R. Richardson, and C. Kiang. 1988. The role of biogenic hydrocarbons in urban photochemical smog: Atlanta as a case study. Science 241: 1473–1475.
Choi, W., A.M. Winer, and S.E. Paulson. 2014. Factors controlling pollutant plume length downwind of major roadways in nocturnal surface inversions. Atmospheric Chemistry and Physics 14: 6925–6940.
Daniels, B., B.S. Zaunbrecher, B. Paas, R. Ottermanns, M. Ziefle, and M. Roß-Nickoll. 2018. Assessment of urban green space structures and their quality from a multidimensional perspective. Science of the Total Environment 615: 1364–1378.
Design Manual for Roads and Bridges (DMRB), volume 11, section 3, part 1, ha20707. http://www.standardsforhighways.co.uk/ha/standards/dmrb/. Accessed 1 May 2017.
Donovan, R.G., C.N. Hewitt, H.E. Stewart, S.M. Owen, and A.R. MacKenzie. 2005. Development and application of an Urban Tree Air Quality Score for photochemical pollution episodes using the Birmingham, United Kingdom, area as a case study. Environmental Science and Technology 39: 6730–6738.
Estrada, F., W.J.W. Botzen, and R.S.J. Tol. 2017. A global economic assessment of city policies to reduce climate change impacts. Nature Climate Change 7: 403–406.
Fowler, D., U. Skiba, E. Nemitz, F. Choubedar, D. Branford, and R. Donovan. 2004. Measuring aerosol and heavy metal deposition on urban woodland and grass using inventories of 210Pb and metal concentrations in soil. Water, Air, and Soil Pollution 4: 483–499.
Fowler, D., M. Amann, F. Anderson, M. Ashmore, P. Cox, M. Depledge, D. Derwent, P. Grennfelt, et al. 2008. Ground-Level Ozone in the 21st Century: Future Trends, Impacts and Policy Implications. Royal Society Policy Document 15/08, RS1276 edn. London: The Royal Society.
Fowler, D., K. Pilegaard, M.A. Sutton, P. Ambus, M. Raivonen, J. Duyzer, D. Simpson, H. Fagerli, et al. 2009. Atmospheric composition change: Ecosystems–atmosphere interactions. Atmospheric Environment 43: 5193–5267.
Gallagher, J., R.W. Baldauf, C. Fuller, P. Kumar, L. Gill, and A. McNabola. 2015. Passive methods for improving air quality in the built environment: A review of porous and solid barriers. Atmospheric Environment 120: 61–70.
Gromke, C., and B. Blocken. 2015. Influence of avenue-trees on air quality at the urban neighborhood scale. Part II: Traffic pollutant concentrations at pedestrian level. Environmental Pollution 196: 176–184.
Gromke, C., N. Jamarkattel, and B. Ruck. 2016. Influence of roadside hedgerows on air quality in urban street canyons. Atmospheric Environment 139: 75–86.
Gröte, R., R. Samson, R. Alonso, J.H. Amorim, P. Cariñanos, G. Churkina, S. Fares, D. Le Thiec, Ü. Niinemets, T.N. Mikkelsen, E. Paoletti, A. Tiwary, and C. Calfapietra. 2016. Functional traits of urban trees: Air pollution mitigation potential. Frontiers in Ecology and the Environment 14: 543–550.
Guenther, A.B., X. Jian, C.L. Heald, T. Sakulyanontvittaya, T. Duhl, L.K. Emmons, and X. Wang. 2012. The Model of Emissions of Gases and Aerosols from Nature version 2.1 (MEGAN2.1): An extended and updated framework for modeling biogenic emissions. Geoscientific Model Development 5: 1471–1492.
Guenther, A., C.N. Hewitt, D. Erickson, R. Fall, C. Geron, T. Graedel, P. Harley, L. Klinger, et al. 1995. A global model of natural volatile organic compound emissions. Journal of Geophysical Research 100: 8873–8892.
Guidolotti, G., C. Calfapietra, E. Pallozzi, G. De Simoni, R. Esposito, M. Mattioni, G. Nicolini, G. Matteucci, et al. 2017. Promoting the potential of flux-measuring stations in urban parks: An innovative case study in Naples, Italy. Agricultural and Forest Meteorology 233: 153–162.
Guo, L., and R.G. Maghirang. 2012. Numerical simulation of air flow and particle collection by vegetative barriers. Engineering Applications of Computational Fluid Mechanics 6: 110–112.
Hale, J.D., T.A.M. Pugh, J.P. Sadler, C.T. Boyko, J. Brown, S. Caputo, M. Caserio, R. Coles, et al. 2015. Delivering a multi-functional and resilient urban forest. Sustainability 7: 4600–4624.
Hallquist, M., J.C. Wenger, U. Baltensperger, Y. Rudich, D. Simpson, M. Claeys, J. Dommen, N.M. Donahue et al. 2009. The formation, properties and impact of secondary organic aerosol: Current and emerging issues. Atmospheric Chemistry and Physics 9: 5155–5236.
Hatanaka, A. 1993. The biogeneration of green odor by green leaves. Phytochemistry 34: 1201–1218.
Heist, D., V. Isakov, S. Perry, M. Snyder, A. Venkatram, C. Hood, J. Stocker, D. Carruthers, et al. 2013. Estimating near-road pollutant dispersion: A model inter-comparison. Transportation Research Part D Transport and Environment 25: 93–105.
Henderson, V., A.J. Venables, T. Regan, and I. Samsonov. 2016. Building functional cities. Science 352: 946–947.
Hofman, J., H. Bartholomeus, S. Janssen, K. Calders, K. Wuyts, S. Van Wittenberghe, and R. Samson. 2016. Influence of tree crown characteristics on the local PM10 distribution inside an urban street canyon in Antwerp (Belgium): A model and experimental approach. Urban Forestry and Urban Greening 20: 265–276.
i-Tree Canopy v6.1. Estimate tree cover and tree benefits for a given area with a random sampling process that lets you easily classify ground cover types. https://canopy.itreetools.org/. Accessed 1 April 2018.
Jacobson, M.Z., W.G. Colella, and D.M. Golden. 2005. Cleaning the air and improving health with hydrogen fuel-cell vehicles. Science 308: 1901–1905.
Janhäll, S. 2015. Review on urban vegetation and particle air pollution—Deposition and dispersion. Atmospheric Environment 105: 130–137.
Jeanjean, A.P.R., R. Buccolieri, J. Eddy, P.S. Monks, and R.J. Leigh. 2017a. Air quality affected by trees in real street canyons: The case of Marylebone neighbourhood in central London. Urban Forestry and Urban Greening 22: 41–53.
Jeanjean, A.P.R., J. Gallagher, P.S. Monks, and R.J. Leigh. 2017b. Ranking current and prospective NO2 pollution mitigation strategies: An environmental and economic modelling investigation in Oxford Street, London. Environmental Pollution 225: 587–597.
Jeanjean, A.P.R., G. Hinchliffe, W.A. McMullan, P.S. Monks, and R.J. Leigh. 2015. A CFD study on the effectiveness of trees to disperse road traffic emissions at a city scale. Atmospheric Environment 120: 1–14.
Keenan, T.F., Ü. Niinemets, S. Sabata, C. Gracia, and J. Peñuelas. 2009. Process based inventory of isoprenoid emissions from European forests: Model comparisons, current knowledge and uncertainties. Atmospheric Chemistry and Physics 9: 4053–4076.
King, E.A., E. Murphy, and A. McNabola. 2009. Reducing pedestrian exposure to environmental pollutants: A combined noise exposure and air quality analysis approach. Transportation Research Part D Transport and Environment 14: 309–316.
Langford, B., E. Nemitz, E. House, G.J. Phillips, D. Fasmulari, B. Davison, J.R. Hopkins, A.C. Lewis, and C.N. Hewitt. 2010. Fluxes and concentrations of volatile organic compounds above central London, UK. Atmospheric Chemistry and Physics 10: 627–645.
Laothawornkitkul, J., J.E. Taylor, N.D. Paul, and C.N. Hewitt. 2009. Biogenic volatile organic compounds in the Earth system. New Phytologist 183: 27–51.
Livesley, S.J., E.G. McPherson, and C. Calfapietra. 2016. The urban forest and ecosystem services: Impacts on urban water, heat, and pollution cycles at the tree, street, and city scale. Journal of Environmental Quality 45: 119–124.
Lombardi, D.R., J.M. Leach, C.D.F. Rogers, and The Urban Futures Team. 2012. Designing Resilient Cities: A Guide to Good Practice. Bracknell: IHS BRE Press.
Lu, J.W.T., E.S. Svendsen, L.K. Campbell, J. Greenfield, J. Braden, K. King, and N. Faixa-Raymond. 2010. Biological, social, and urban design factors affecting young street tree mortality in New York City. Cities and the Environment 3: 1–15.
MacKenzie, A.R., R.M. Harrison, I. Colbeck, and C.N. Hewitt. 1991. The role of biogenic hydrocarbons in the production of ozone in urban plumes in southeast England. Atmospheric Environment 25: 351–359.
McNabola, A., B.M. Broderick, and L.W. Gill. 2009. A numerical investigation of the impact of low boundary walls on pedestrian exposure to air pollutants in urban street canyons. Science of the Total Environment 407: 760–769.
Mentel, T.F., J. Wildt, A. Kiendler-Scharr, E. Kleist, R. Tillmann, M. Dal Maso, R. Fisseha, T. Hohaus,et al. 2009. Photochemical production of aerosols from real plant emissions. Atmospheric Chemistry and Physics 9: 4387–4406.
Moeller, E. 2015. Suggestions for the Skyscrapers of tomorrow—International Highrise Award 2014. Stahlbau 84: U139–U195.
Moradpour, M., H. Afshin, and B. Farhanieh. 2017. A numerical investigation of reactive air pollutant dispersion in urban street canyons with tree planting. Atmospheric Pollution Research 8: 1–14.
Morani, A., D.J. Nowak, S. Hirabayashi, and C. Calfapietra. 2011. How to select the best tree planting locations to enhance air pollution removal in the MillionTreesNYC Initiative. Environmental Pollution 159: 1040–1047.
Neft, I., M. Scungio, N. Culver, and S. Singh. 2016. Simulations of aerosol filtration by vegetation: Validation of existing models with available lab data and application to near-roadway scenario. Aerosol Science and Technology 50: 937–946.
Ng, W.-Y., and C.-K. Chau. 2012. Evaluating the role of vegetation on the ventilation performance in isolated deep street canyons. International Journal of Environment and Pollution 50: S98–S110.
Nowak, D.J., and D.E. Crane. 2002. Carbon storage and sequestration by urban trees in the USA. Environmental Pollution 116: 381–389.
Nowak, D., D.E. Crane, and J.C. Stevens. 2006. Air pollution removal by urban trees and shrubs in the United States. Urban Forestry and Urban Greening 4: 115–123.
Nowak, D.J., S. Hirabayashi, A. Bodine, and R. Hoehna. 2013. Modeled PM2.5 removal by trees in ten US cities and associated health effects. Environmental Pollution 178: 395–402.
Oke, T.R. 1988. Street design and urban canopy layer climate. Energy and Buildings 11: 103–113.
Owne, S.M., A.R. MacKenzie, R.G.H. Bunce, H.E. Stewart, R.G. Donovan, G. Stark, and C.N. Hewitt. 2006. Classifying urban land for stratified sampling and surveys, using Principal Component Analysis with quantified uncertainties. Landscape and Urban Planning 78: 311–321.
Padro, J. 1996. Summary of ozone dry deposition velocity measurements and model estimates over vineyards, grass and deciduous forests in summer. Atmospheric Environment 30: 2363–2369.
Pincetl, S., T. Gillespie, D.E. Pataki, S. Saatchi, and J.-D. Saphores. 2013. Urban tree planting programs, function or fashion? Los Angeles and urban tree planting campaigns. GeoJournal 78: 475–493.
Prather, M., and A.H. Jaffe. 1990. Global impact of the Antarctic ozone hole: Chemical propagation. Journal of Geophysical Research 95: 3473–3492.
Pugh, T.A.M., A.R. MacKenzie, J.D. Whyatt, and C.N. Hewitt. 2012. The effectiveness of green infrastructure for improvement of urban air quality. Environmental Science and Technology 46: 7692–7699.
Raine, J.K., and D.C. Stevenson. 1977. Wind protection by model fences in a simulated atmospheric boundary layer. Journal of Wind Engineering and Industrial Aerodynamics 2: 159–180.
Ratti, C., S. Di Sabatino, and R. Bitter. 2006. Urban texture analysis with image processing techniques: Wind and dispersion. Theoretical and Applied Climatology 84: 77–99.
Salmond, J.A., M. Tadaki, S. Vardoulakis, K. Arbuthnott, A. Coutts, M. Demuzere, K.N. Dirks, C. Heaviside, S. Lim, H. Macintyre, R.N. McInnes, and B.W. Wheeler. 2016. Health and climate related ecosystem services provided by street trees in the urban environment. Environmental Health 15: 36.
Schiermeier, Q. 2015. The science behind the Volkswagen emissions scandal. Nature. https://doi.org/10.1038/nature.2015.18426.
Sehmel, G.A. 1980. Particle and gas deposition: A review. Atmospheric Environment 14: 983–1011.
Sillman, S. 1999. The relation between ozone, NOx and hydrocarbons in urban and polluted rural environments. Atmospheric Environment 33: 1821–1845.
Speak, A.F., J.J. Rothwell, S.J. Lindley, and C.L. Smith. 2012. Urban particulate pollution reduction by four species of green roof vegetation in a UK city. Atmospheric Environment 61: 283–293.
Specifind: developed by Cost FP1024 GreenInUrbs: Nature based solutions for sustainable and resilient cities. http://www.greeninurbs.com/p_specifind/. Accessed 1 Oct 2017.
Stocker, J., D. Heist, C. Hood, V. Isakov, D. Carruthers, S. Perry, M. Snyder, A. Venkatram, et al. 2013. Road source model intercomparison study using new and existing datasets. In 15th International Conference on Harmonisation, Madrid, Spain. http://www.harmo.org/Conferences/Proceedings/_Madrid/publishedSections/H15-78.pdf. Accessed 3 Jan 2019.
Tan, D.G.H., P.H. Haynes, A.R. MacKenzie, and J.A. Pyle. 1998. Effects of fluid dynamical stirring and mixing on the deactivation of stratospheric chlorine. Journal of Geophysical Research 103: 1585–1605.
Tiwary, A., H.P. Morvan, and J.J. Colls. 2005. Modelling the size-dependent collection efficiency of hedgerows for ambient aerosols. Journal of Aerosol Science 37: 990–1015.
Tong, Z., R.W. Baldauf, V. Isakov, P. Deshmukh, and K.M. Zhang. 2016. Roadside vegetation barrier designs to mitigate near-road air pollution impacts. Science of the Total Environment 541: 920–927.
Treeconomics. 2015. Valuing London’s Urban Forest: Report of the London iTree Eco Project. https://www.forestry.gov.uk/pdf/LONDONI-TREEECOREPORT151202.pdf/$FILE/LONDONI-TREEECOREPORT151202.pdf. Accessed 3 Jan 2019.
Trees, Design and Action Group (TDAG). 2012. Trees in the Townscape: A Guide for Decision Makers. http://www.tdag.org.uk/trees-in-the-townscape.html. Accessed 3 Jan 2019.
Trees, Design and Action Group (TDAG). 2014. Trees in Hard Landscapes: A Guide for Delivery. http://www.tdag.org.uk/trees-in-hard-landscapes.html. Accessed 3 Jan 2019.
van den Hurk, B.J.J.M., P. Viterbo, and O.L. Sietse. 2003. Impact of leaf area index seasonality on the annual land surface evaporation in a global circulation model. Journal of Geophysical Research 108: 4191.
Vos, P.E.J., B. Maiheu, J. Vankerkom, and S. Janssen. 2013. Improving local air quality in cities: To tree or not to tree? Environmental Pollution 183: 113–122.
Wang, J.-L., C. Chew, C.-Y. Chang, W.-C. Liao, S.-C. Candice Lung, W.-N. Chen, P.-J. Lee, P.-H. Lin, et al. 2013. Biogenic isoprene in subtropical urban settings and implications for air quality. Atmospheric Environment 79: 369–379.
World Health Organisation. 2016. Ambient Air Pollution: A Global Assessment of Exposure and Burden of Disease. http://apps.who.int/iris/bitstream/10665/250141/1/9789241511353-eng.pdf. Accessed 3 Jan 2019.
Wyche, K.P., A.C. Ryan, C.N. Hewitt, M.R. Alfarra, G. McFiggans, T. Carr, P.S. Monks, K.L. Smallbone, et al. 2014. Emissions of biogenic volatile organic compounds and subsequent photochemical production of secondary organic aerosol in mesocosm studies of temperate and tropical plant species. Atmospheric Chemistry and Physics 14: 12781–12801.
Yang, J., J. McBride, J. Zhou, and Z. Sun. 2005. The urban forest in Beijing and its role in air pollution reduction. Urban Forestry and Urban Greening 3: 65–78.
Yang, J., Q. Yu, and P. Gong. 2008. Quantifying air pollution removal by green roofs in Chicago. Atmospheric Environment 42: 7266–7273.
Young, R.F. 2011. Planting the living city: Best practices in planning green infrastructure—Results from major US cities. Journal of the American Planning Association 77: 368–381.
Acknowledgements
We acknowledge support from Lancaster University and from a Royal Society Wolfson Research Merit Award (CNH); a Royal Society Dorothy Hodgkins Research Fellowship (KA); the European Research Council through the FASTER Project (Project ID 320821) and the Natural Environment Research Council (NERC) through the CityFlocks Project (NE/N003195/1) (A.R.M.K.). We thank Emma Ferranti (University of Birmingham), who is funded by an NERC Knowledge Exchange Fellowship, for assistance with our dissemination plan. We thank Studio Signorella and http://Reduction.org for the design and production of figures.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Hewitt, C.N., Ashworth, K. & MacKenzie, A.R. Using green infrastructure to improve urban air quality (GI4AQ). Ambio 49, 62–73 (2020). https://doi.org/10.1007/s13280-019-01164-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13280-019-01164-3