Abstract
Optical fiber sensing technology has developed rapidly since the 1980s with the development of the optical fiber and fiber optical communication technology. It is a new type of sensing technology that uses light as a carrier and optical fiber as a medium to sense and transmit external signals (measurands). Distributed fiber optical sensors (DFOS) can continuously measure the external physical parameters distributed along the geometric path of the optical fiber. Meanwhile, the spatial distribution and change information of the measured physical parameters over time can be obtained. This technology has unmatched advantages over traditional point-wise and electrical measurement monitoring technologies. This paper summarizes the state-of-the-art research of the application of the distributed optical fiber sensing technology in geo-engineering in the past 10 years, mainly including the advantages of DFOS, the challenges in geo-engineering monitoring, related fundamental theoretical issues, sensing performance of the optical sensing cables, distributed optical fiber monitoring system for geo-engineering, and applications of optical fiber sensing technology in geo-engineering.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
L. Schenato, “A review of distributed fibre optic sensors for geo-hydrological applications,” Applied Sciences, 2017, 7(9): 896.
M. Iten and A. M. Puzrin, “BOTDA road-embedded strain sensing system for landslide boundary localization,” in Smart Sensor Phenomena, Technology, Networks, and Systems 2009. International Society for Optics and Photonics, San Diego, California, USA, 2009, pp. 729312–729316.
W. R. Habel, D. Hofmann, H. Döring, H. Jentsch, A. Senze, and G. Kowalle, “Detection of a slipping soil area in an open coal pit by embedded fibre-optic sensing rods,” in the 5th International Forum on Opto-electronic Sensor-Based Monitoring, China, 2014, pp. 1–7.
A. Klar, P. J. Bennett, K. Soga, R. J. Mair, P. Tester, R. Fernie, et al., “Distributed strain measurement for pile foundation,” Proceedings of the Institution of Civil Engineers — Geotechnical Engineering, 2006, 159(3): 135–144.
L. L. K. Cheung, K. Soga, P. J. Bennett, Y. Kobayashi, B. Amatya, and P. Wright, “Optical fibre strain measurement for tunnel lining monitoring,” Proceedings of the Institution of Civil Engineers — Geotechnical Engineering, 2010, 163(3): 119–130.
H. Mohamad, P. J. Bennett, K. Soga, R. J. Mair, and K. Bowers, “Behaviour of an old masonry tunnel due to tunnelling-induced ground settlement,” Géotechnique, 2010, 60(12): 927–938.
H. Mohamad, K. Soga, A. Pellew, and P. J. Bennett, “Performance monitoring of a secant-piled wall using distributed fiber optic strain sensing,” Journal of Geotechnical and Geoenvironmental Engineering, 2011, 137(12): 1236–1243.
H. Mohamad, K. Soga, P. J. Bennett, R. J. Mair, and C. S. Lim, “Monitoring twin tunnel interaction using distributed optical fiber strain measurements,” Journal of Geotechnical and Geoenvironmental Engineering, 2012, 138(8): 957–967.
H. Mohamad, K. Soga, and B. Amatya, “Thermal strain sensing of concrete piles using Brillouin optical time domain reflectometry,” Geotechnical Testing Journal, 2014, 37(2): 333–346.
L. Olivares, E. Damiano, R. Greco, L. Zeni, L. Picarelli, A. Minardo, et al., “An instrumented flume to investigate the mechanics of rainfall-induced landslides in unsaturated granular soils,” Geotechnical Testing Journal, 2009, 32(2): 788–796.
L. Picarelli, E. Damiano, R. Greco, A. Minardo, L. Olivares, and L. Zeni, “Performance of slope behavior indicators in unsaturated pyroclastic soils,” Journal of Mountain Science, 2015, 12(6): 1434–1447.
E. Damiano, B. Avolio, A. Minardo, L. Olivares, L. Picarelli, and L. Zeni, “A laboratory study on the use of optical fibers for early detection of pre-failure slope movements in shallow granular soil deposits,” Geotechnical Testing Journal, 2017, 40(4): 529–541.
Y. T. Ho, A. B. Huang, and J. T. Lee, “Development of a fibre Bragg grating sensored ground movement monitoring system,” Measurement Science and Technology, 2006, 17(7): 1733–1740.
Y. T. Ho, A. B. Huang, and J. Lee, “Development of a chirped/differential optical fiber Bragg grating pressure sensor,” Measurement Science and Technology, 2008, 19(4): 045304.
A. B. Huang, C. Wang, J. Lee, and Y. T. Ho, “Applications of FBG-based sensors to ground stability monitoring,” Journal of Rock Mechanics and Geotechnical Engineering, 2016, 8(4): 513–520.
J. H. Yin, “From constitutive modeling to development of laboratory testing and optical fiber sensor monitoring technologies,” Chinese Journal of Geotechnical Engineering, 2011, 33(1): 1–15.
H. F. Pei, P. Cui, J. H. Yin, H. Zhu, X. Chen, L. Pei, et al., “Monitoring and warning of landslides and debris flows using an optical fiber sensor technology,” Journal of Mountain Science, 2011, 8(5): 728–738.
H. F. Pei, J. H. Yin, H. Zhu, C. Y. Hong, W. Jin, and D. S. Xu, “Monitoring of lateral displacements of a slope using a series of special fibre Bragg grating-based in-place inclinometers,” Measurement Science and Technology, 2012, 23(2): 025007.
D. S. Xu and J. H. Yin, “Analysis of excavation induced stress distributions of GFRP anchors in a soil slope using distributed fiber optic sensors,” Engineering Geology, 2016, 213: 55–63.
B. Shi, D. Zhang, and H. H. Zhu, Distributed fiber optic sensing for geoengineering monitoring. Beijing: Science Press, 2019.
J. F. Yan, B. Shi, H. H. Zhu, B. J. Wang, G. Q. Wei, and D. F. Cao, “A quantitative monitoring technology for seepage in slopes using DTS,” Engineering Geology, 2015, 186: 100–104.
D. F. Cao, B. Shi, H. H. Zhu, G. Q. Wei, S. E. Chen, and J. F. Yan, “A distributed measurement method for in-situ soil moisture content by using carbon-fiber heated cable,” Journal of Rock Mechanics and Geotechnical Engineering, 2015, 7(6): 700–707.
D. F. Cao, B. Shi, G. Q. Wei, S. E. Chen, and H. H. Zhu, “An improved distributed sensing method for monitoring soil moisture profile using heated carbon fibers,” Measurement: Journal of the International Measurement Confederation, 2018, 123: 175–184.
Y. L. Liu, H. Y. Sun, Y. Yu, W. Zhan, and Y. Q. Shang, “BOTDR monitoring analysis of anti-sliding pile internal force,” Journal of Zhejiang University (Engineering Science), 2012, 46(2): 243–249.
J. Chai, X. Huo, Y. Qian, D. Zhang, Q. Yuan, and Y. Li, “Model test for evaluating deformation and weighting of overlying strata by distributed optical fiber sensing,” Journal of China Coal Society, 2018, 43(S1): 36–43.
Y. Ding, B. Shi, X. Y. Bao, and J. Q. Gao, “Jacket effect on strain measurement accuracy for distributed strain sensors based on Brillouin scattering,” Optica Applicata, 2006, 36(1): 57–67.
F. Ansari and L. B. Yuan, “Mechanics of bond and interface shear transfer in optical fiber sensors,” Journal of Engineering Mechanics, 1998, 124(4): 385–394.
D. S. Li, H. N. Li, L. Ren, and G. B. Song, “Strain transferring analysis of fiber Bragg grating sensors,” Optical Engineering, 2006, 45(2): 024402.
Y. Zhang, P. Gao, H. M. Wang, B. Shi, and L. Qi, “Study on strain transfer characteristics of distributed optical fiber sensor under complex deformation condition,” Journal of Disaster Prevention and Mitigation Engineering, 2013, 33: 566–572.
M. Iten, A. M. Puzrin, D. Hauswirth, S. Foaleng-Mafang, J. C. Beugnot, and L. Thévenaz, “Study of a progressive failure in soil using BEDS,” in the 20th International Conference on Optical Fibre Sensors, United Kingdom, October 5–9, 2009, pp. 75037S.
D. Hauswirth, M. Iten, and A. M. Puzrin, “Detection of ground movements using soil-embedded distributed fiber optic sensors,” in the 4th International Conference on Site Characterization ISC-4, Boca Raton, 2012, pp. 579–586.
C. C. Zhang, H. H. Zhu, B. Shi, and J. K. She, “Interfacial characterization of soil-embedded optical fiber for ground deformation measurement,” Smart Materials and Structures, 2014, 23(9): 095022.
C. C. Zhang, H. H. Zhu, and B. Shi, “Role of the interface between distributed fibre optic strain sensor and soil in ground deformation measurement,” Scientific Reports, 2016, 6(1): 1–9.
B. Li, D. Zhang, X. Chen, J. Wang, and B. Shi, “Testing method on performance of deformation coupling between distributed sensing fiber and soil,” Geological Journal of China Universities, 2017, 23(4): 633–639.
L. Schenato, L. Palmieri, M. Camporese, S. Bersan, S. Cola, A. Pasuto, et al., “Distributed optical fibre sensing for early detection of shallow landslides triggering,” Scientific Reports, 2017, 7(1): 1–7.
K. E. Winters, M. C. Quinn, and O. D. S. Taylor, “Assessing the frictional resistance between fiber-optic sensor cable and different soil types,” in Geo-Congress 2020: Modeling, Geomaterials, and Site Characterization, Minneapolis, 2020, pp. 164–171.
ASTM, “Standard practice for use of distributed optical fiber sensing systems for monitoring the impact of ground movements during tunnel and utility construction on existing underground utilities,” West Conshohocken, PA: ASTM, USA, 2014.
C. C. Zhang, B. Shi, H. H. Zhu, B. J. Wang, and G. Q. Wei, “Toward distributed fiber-optic sensing of subsurface deformation: a theoretical quantification of ground-borehole-cable interaction,” Journal of Geophysical Research: Solid Earth, 2020, 125(3): e2019JB018878.
D. Hauswirth, M. Iten, R. Richli, and A. M. Puzrin, “Fibre optic cable and micro-anchor pullout tests in sand,” in Physical Modelling in Geotechnics, Two Volume Set: Proceedings of the 7th International Conference on Physical Modelling in Geotechnics (ICPMG 2010), Zurich, Switzerland; Boca Raton, Florida, United States, June 28th-July 1st, 2010, pp. 337–342.
D. Hauswirth, A. M. Puzrin, A. Carrera, and M. S. P. Wan, “Use of fibre-optic sensors for simple assessment of ground surface displacements during tunnelling,” Geotechnique, 2014, 64(10): 837–842.
H. H. Zhu, B. Shi, J. Zhang, J. F. Yan, and C. C. Zhang, “Distributed fiber optic monitoring and stability analysis of a model slope under surcharge loading,” Journal of Mountain Science, 2014, 11(4): 979–989.
R. You, L. Ren, and G. Song, “A novel fiber Bragg grating (FBG) soil strain sensor,” Measurement, 2019, 139: 85–91.
C. C. Zhang, H. H. Zhu, D. D. Chen, X. Y. Xu, B. Shi, and X. P. Chen, “Feasibility study of anchored fiber-optic strain-sensing arrays for monitoring soil deformation beneath model foundation,” Geotechnical Testing Journal, 2018, 42(4): 966–984.
C. C. Zhang, H. H. Zhu, S. P. Liu, B. Shi, and G. Cheng, “Quantifying progressive failure of micro-anchored fiber optic cable-sand interface via high-resolution distributed strain sensing,” Canadian Geotechnical Journal, 2020, 57(6): 871–881.
S. Zhang, “Study on mechanical coupling between anchored strain sensing optical cable and soil deformation,” MEng dissertation, Nanjing University, Nanjing, China, 2019.
C. C. Zhang, B. Shi, K. Gu, S. P. Liu, J. H. Wu, S. Zhang, et al., “Vertically distributed sensing of deformation using fiber optic sensing,” Geophysical Research Letters, 2018, 45(21): 11732–11741.
D. F. Cao, B. Shi, H. H. Zhu, H. I. Inyang, G. Q. Wei, and C. Z. Duan, “A soil moisture estimation method using actively heated fiber Bragg grating sensors,” Engineering Geology, 2018, 242: 142–149.
V. R. Tarnawski and W. H. Leong, “Thermal conductivity of soils at very low moisture content and moderate temperatures,” Transport in Porous Media, 2000, 41(2): 137–147.
M. Y. Sun, B. Shi, D. Zhang, J. Liu, J. Y. Guo, G. Q. Wei, et al., “Study on calibration model of soil water content based on actively heated fiber-optic FBG method in the in-situ test,” Measurement, 2020, 165: 108176.
J. Liu, M. Y. Sun, B. Shi, G. Q. Wei, J. Y. Guo, and X. Zheng, “Feasibility study on the actively heated FBG methods for dry density measurement,” Chinese Journal of Geotechnical Engineering, 2020, 43(2): 390–396.
J. Y. Guo, B. Shi, M. Y. Sun, C. C. Zhang, G. Q. Wei, and J. Liu, “Characterization of an ORMOCER®-coated FBG sensor for relative humidity sensing,” Measurement, 2021, 171(4): 108851.
D. M. Liu, T. He, Z. J. Xu, and Q. Z. Sun, “New type of microstructure-fiber distributed acoustic sensing technology and its applications,” Journal of Applied Sciences — Electronics and Information Engineering, 2020, 38(2): 296–309.
D. Zhang, J. C. Wang, B. Li, and B. Shi, “Fatigue characteristics of distributed sensing cables under low cycle elongation,” Smart Structures and Systems, 2016, 18(6): 1203–1215.
G. Q. Wei, “Distributed monitoring for engineering soil deformation with optical fiber sensors,” Ph.D dissertation, Nanjing University, Nanjing, China, 2008.
Y. J. Sun, “Bank slope multi-fields monitoring based on fiber optic sensing technologies and stability evaluation study,” PhD dissertation, Nanjing University, Nanjing, China, 2015.
B. Shi, H. Z. Xu, D. Zhang, D. Yong, H. L. Cui, B. Chen, et al., “Feasibility study on application of BOTDR to health monitoring for large infrastructure engineering,” Chinese Journal of Rock Mechanics and Engineering, 2004, 23(3): 493–499.
Y. Lu, B. Shi, G. Q. Wei, S. E. Chen, and D. Zhang, “Application of a distributed optical fiber sensing technique in monitoring the stress of precast piles,” Smart Materials & Structures, 2012, 21(11): 115011.
L. Pelecanos and K. Soga, “Development of load-transfer curves for axially-loaded piles using fiber-optic strain data, finite element analysis and optimization,” in the 9th European Conference on Numerical Methods in Geotechnical Engineering, Portugal, 2018, pp. 1025–1030.
Y. J. Sun, X. Li, R. Cun, H. Z. Xu, and A. M. Han, “Distributed fiber optic sensing and data processing of axial loaded precast piles,” IEEE Access, 2020, 8: 169136–169145.
B. Shi, H. Xu, B. Chen, D. Zhang, Y. Ding, H. Cui, et al., “A feasibility study on the application of fiber-optic distributed sensors for strain measurement in the Taiwan Strait Tunnel project,” Marine Georesources and Geotechnology, 2003, 21(3–4): 333–343.
A. Klar, I. Dromy, and R. Linker, “Monitoring tunneling induced ground displacements using distributed fiber-optic sensing,” Tunnelling and Underground Space Technology, 2014, 40: 141–150.
X. Wang, B. Shi, G. Q. Wei, S. E. Chen, H. Zhu, and T. Wang, “Monitoring the behavior of segment joints in a shield tunnel using distributed fiber optic sensors,” Structural Control and Health Monitoring, 2018, 25(1): e2056.
M. Fajkus, J. Nedoma, P. Mec, E. Hrubesova, R. Martinek, and V. Vasinek, “Analysis of the highway tunnels monitoring using an optical fiber implemented into primary lining,” Journal of Electrical Engineering, 2017, 68(5): 364–370.
H. G. Yu, X. B. Bing, H. U. Tao, S. Y. Yin, and Y. C. Han, “Fiber sheath effect in tunneling monitoring based on BOTDR technology,” Rock and Soil Mechanics, 2017, 38(8): 2441–2447.
G. Yao, “Loess tunnel lining cracking analysis and monitoring system research,” in the 1st International Conference on Transportation Infrastructure and Materials (ICTIM 2016), China, 2016: 760–766.
S. Manandhar, K. Miyazoe, S. Fukuoka, T. Hino, Dennes T. Bergado, and T. Koumoto, “Observation of static load of l-shaped retaining wall constructed on short wooden pile using fiber optic geogrid BOTDR method,” Indian Geotechnical Journal, 2016, 46(4): 398–407.
C. Y. Hong, Y. F. Zhang, G. W. Li, M. X. Zhang, and Z. X. Liu, “Recent progress of using Brillouin distributed fiber optic sensors for geotechnical health monitoring,” Sensors and Actuators A: Physical, 2017, 258: 131–145.
C. Zhu, K. Zhang, H. Cai, Z. Tao, B. An, M. He, et al., “Combined application of optical fibers and CRLD bolts to monitor deformation of a pit-in-pit foundation,” Advances in Civil Engineering, 2015, 2019(1): 1–16.
D. Zhang, Q. Xu, A. Bezuijen, G. Zheng, and H. X. Wang, “Internal deformation monitoring for centrifuge slope model with embedded FBG arrays,” Landslides, 2017, 14(1): 407–417.
M. Zeng, H. Zhao, D. Wu, H. Chen, and J. Cai, “A vibration-based traffic monitoring system using distributed optical sensing technology,” Journal of Testing and Evaluation, 2020, 48(3): 1799–1813.
M. Bonopera, K. C. Chang, C. C. Chen, Z. K. Lee, Y. C. Sung, and N. Tullini, “Fiber Bragg grating-differential settlement measurement system for bridge displacement monitoring: case study,” Journal of Bridge Engineering, 2019, 24(10): 05019011.
C. Du, S. Dutta, P. Kurup, T. Yu, and X. Wang, “A review of railway infrastructure monitoring using fiber optic sensors,” Sensors and Actuators A: Physical, 2020, 303: 111728.
H. H. Zhu, B. Shi, and C. C. Zhang, “FBG-based monitoring of geohazards: current status and trends,” Sensors, 2017, 17(3): 452.
Y. J. Sun, D. Zhang, B. Shi, H. J. Tong, G. Q. Wei, and X. Wang, “Distributed acquisition, characterization and process analysis of multi-field information in slopes,” Engineering Geology, 2014, 182: 49–62.
Y. Sun, B. Shi, D. Zhang, H. Tong, G. Wei, and H. Xu, “Internal deformation monitoring of slope based on BOTDR,” Journal of Sensors, 2016, 2016: 1–8.
K. Gu, B. Shi, C. Liu, H. Jiang, T. Li, and J. Wu, “Investigation of land subsidence with the combination of distributed fiber optic sensing techniques and microstructure analysis of soils,” Engineering Geology, 2018, 240: 34–47.
H. Han, B. Shi, and L. Zhang, “Prediction of landslide sharp increase displacement by SVM with considering hysteresis of groundwater change,” Engineering Geology, 2021, 280: 105876.
S. P. Liu, B. Shi, K. Gu, C. Zhang, and P. Yang, “Land subsidence monitoring in sinking coastal areas using distributed fiber optic sensing: a case study,” Natural Hazards, 2020, 103(3): 3043–3061.
H. Sang, D. Zhang, Y. Gao, L. Zhang, G. Wang, B. Shi, et al., “Strain distribution based geometric models for characterizing the deformation of a sliding zone,” Engineering Geology, 2019, 263: 105300.
D. Zhang, J. C. Wang, P. S. Zhang, and B. Shi, “Internal strain monitoring for coal mining similarity model based on distributed fiber optical sensing,” Measurement, 2017, 97: 234–241.
L. Zhang, B. Shi, H. Zhu, X. B. Yu, H. Han, and X. Fan, “PSO-SVM-based deep displacement prediction of Majiagou landslide considering the deformation hysteresis effect,” Landslides, 2021, 18(1): 179–193.
M. Gil-Rodríguez, L. Rodríguez-Sinobas, J. Benítez-Buelga, and R. Sánchez-Calvo, “Application of active heat pulse method with fiber optic temperature sensing for estimation of wetting bulbs and water distribution in drip emitters,” Agricultural Water Management, 2013, 120: 72–78.
C. Sayde, C. Gregory, M. Gil-Rodriguez, N. Tufillaro, and J. S. Selker, “Feasibility of soil moisture monitoring with heated fiberoptics,” Water Resources Research, 2010, 46(6): W06201.
J. H. Wu, B. Shi, D. F. Cao, H. T. Jiang, X. F. Wang, and K. Gu, “Model test of soil deformation response to draining-recharging conditions based on DFOS,” Engineering Geology, 2017, 226: 107–121.
R. Wu, V. Martin, J. McKenzie, S. Broda, B. Bussière, M. Aubertin, et al., “Laboratory-scale assessment of a capillary barrier using fibre optic distributed temperature sensing (FO-DTS),” Canadian Geotechnical Journal, 2020, 57(1): 115–126.
J. Benítez-Buelga, L. Rodríguez-Sinobas, R. S. Calvo, M. Gil-Rodríguez, C. Sayde, and J. S. Selker, “Calibration of soil moisture sensing with subsurface heated fiber optics using numerical simulation,” Water Resources Research, 2016, 52(4): 2985–2995.
C. Sayde, J. B. Buelga, L. Rodriguez-Sinobas, L. El Khoury, M. English, N. van de Giesen, et al., “Mapping variability of soil water content and flux across 1–1 000 m scales using the actively heated fiber optic method,” Water Resources Research, 2014, 50(9): 7302–7317.
A. M. Striegl and S. P. Loheide II, “Heated distributed temperature sensing for field scale soil moisture monitoring,” Groundwater, 2012, 50(3): 340–347.
N. J. Lindsey, T. C. Dawe, and J. B. Ajo-Franklin, “Illuminating seafloor faults and ocean dynamics with dark fiber distributed acoustic sensing,” Science, 2019, 366(6469): 1103–1107.
E. F. Williams, M. R. Fernández-Ruiz, R. Magalhaes, R. Vanthillo, and H. F. Martins, “Distributed sensing of microseisms and teleseisms with submarine dark fibers,” Nature Communications, 2019, 10(1): 1–11.
Acknowledgment
This work was supported by the National Natural Science Foundation of China (Grant Nos. 42030701, 41427801, and 42077233).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Shi, B., Zhang, D., Zhu, H. et al. DFOS Applications to Geo-Engineering Monitoring. Photonic Sens 11, 158–186 (2021). https://doi.org/10.1007/s13320-021-0620-y
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13320-021-0620-y