Abstract
The elastohydrodynamic (EHD) friction properties of seven ISO VG 320 gear oils including three polyalphaolefins (PAOs), three polyglycols (PG) and a mineral oil have been investigated in rolling/sliding conditions at six different temperatures and three roughnesses. Film thickness, Stribeck and traction curves have been generated using a ball-on-disc tribometer. Film thickness results are in agreement with previous work that it is primarily controlled by pressure-viscosity coefficient and viscosity of lubricants. The results with smooth surface show that all oils experience significant shear heating leading to friction reduction at higher strain rates or lambda ratios but only PGs reach limiting friction whereas mineral oil and PAOs do not. Friction curves obtained at different temperatures and roughnesses enable simulating an extensive range of lubrication regimes and allow isothermal friction correction for shear heating. Stribeck curves with rough surfaces show an increase in friction in the lambda range of 0.5–3.5, where asperity separation varies from partial to full–indicating that roughness effects can be expected even under full film condition. This increase in friction is attributed to formation of a micro-EHD region, and is seen only with mineral oil and PAOs whereas not with PGs. The results also highlight how EHD friction properties of different family of fluids could be influenced by roughness effects, and the possible mechanisms are discussed.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Greaves M. Pressure viscosity coefficients and traction properties of synthetic lubricants for wind turbine gear systems. Lubr Sci24(2): 75–83 2012
Gunsel S, Korcek S, Smeeth M, Spikes H A. The elastohydrodynamic friction and film forming properties of lubricant base oils. Tribol Trans42(3): 559–569 1999
Guegan J, Kadiric A, Gabelli A, Spikes H A. The relationship between friction and film thickness in EHD point contacts in the presence of longitudinal roughness. Tribol Lett64(3): 33 2016
Vengudusamy B, Grafl A, Novotny-Farkas F, Schöfmann W. Influence of surface roughness on the tribological behavior of gear oils in steel-steel contacts: Part I–Boundary friction properties. Tribol Trans57(2): 256–266 2014
Vengudusamy B, Grafl A, Novotny-Farkas F, Schöfmann W. Influence of surface roughness on the tribological behavior of gear oils in steel-steel contacts: Part II–Mixed friction properties. Tribol Trans57(4): 561–569 2014
Jefferis J A, Johnson K L. First paper: sliding friction between lubricated rollers. Proc Inst Mech Eng182(1): 281–291 1967
Evans C R, Johnson K L. The influence of surface roughness on elastohydrodynamic traction. Proc Inst Mech EngPart C J Mech Eng Sci201(2): 145–150 1987
Britton R D, Elcoate C D, Alanou M P, Evans H P, Snidle R W. Effect of surface finish on gear tooth friction. J Tribol122(1): 354–360 2000
Jeng Y R. Experimental study of the effects of surface roughness on friction. Tribol Trans33(3): 402–410 1990
Jacod B, Venner C H, Lugt P M. Influence of longitudinal roughness on friction in EHL contacts. J Tribol126(3): 473–481 2004
LaFountain A R, Johnston G J, Spikes H A. The elastohydrodynamic traction of synthetic base oil blends. Tribol Trans44(4): 648–656 2001
Martins R, Seabra J, Brito A, Seyfert C, Luther R, Igartua A. Friction coefficient in FZG gears lubricated with industrial gear oils: biodegradable ester vs. mineral oil. Tribol Int39(6): 512–521 2006
Fernandes C M C G, Martins R C, Seabra J H O. Friction torque of cylindrical roller thrust bearings lubricated with wind turbine gear oils. Tribol Int59: 121–128 2013
Spikes H A, Zhang J. History, origins and prediction of elastohydrodynamic friction. Tribol Lett56(1): 1–25 2014
Hentschel K-H. The influence of molecular structure on the frictional behaviour of lubricating fluids. J Synth Lubr2(2): 143–165 1985
Höhn B R, Michaelis K, Doleschel A. Frictional behaviour of synthetic gear lubricants. Tribol Ser39: 759–768 2001
Muraki M. Molecular structure of synthetic hydrocarbon oils and their rheological properties governing traction characteristics. Tribol Int20(6): 347–354 1987
Zhang J, Tan A, Spikes H. Effect of base oil structure on elastohydrodynamic friction. Tribol Lett65(1): 13 2017
Jacod B, Venner C H, Lugt P M. Extension of the friction mastercurve to limiting shear stress models. J Tribol125(4): 739–746 2003
Martinie L, Vergne P. Tribology in transportation: the contribution of the lubricant rheology for optimizing the behavior of EHD contacts. In First African Congress in Tribology, Marrakech, Morocco, 2014.
Bair S, Winer W O. Regimes of traction in concentrated contact lubrication. J Lubr Technol104(3): 382–386 1982
Nanbu T, Chiba N, Kano M, Ushijima K. Effect of surface roughness on elastohydrodynamic traction: Part 1. Lubr Sci17(3): 281–293 2005
Björling M, Larsson R, Marklund P, Kassfeldt E. Elastohydrodynamic lubrication friction mapping–the influence of lubricant, roughness, speed, and slide-to-roll ratio. Proc Inst Mech Eng Part J: J Eng Tribol225(7): 671–681 2011
Zapletal T, Sperka P, Krupka I, Hartl M. The effect of surface roughness on friction and film thickness in transition from EHL to mixed lubrication. Tribol Int128: 356–364 2018
Venner C H, Lubrecht A A. Numerical analysis of the influence of waviness on the film thickness of a circular EHL contact. J Tribol118(1): 153–161 1996
Lubrecht A A, Venner C H. Elastohydrodynamic lubrication of rough surfaces. Proc Inst Mech Eng Part J: J Eng Tribol213(5): 397–404 1999
Guegan J, Kadiric A, Spikes H. A study of the lubrication of EHL point contact in the presence of longitudinal roughness. Tribol Lett59(1): 22 2015
Greenwood J A, Morales-Espejel G E. The behaviour of transverse roughness in EHL contacts. Proc Inst Mech Eng Part J: J Eng Tribol208(2): 121–132 1994
Johnston G J, Wayte R, Spikes H A. The measurement and study of very thin lubricant films in concentrated contacts. Tribol Trans34(2): 187–194 1991
Spikes H. Basics of EHL for practical application. Lubr Sci27(1): 45–67 2015
Chittenden R J, Dowson D, Dunn J F, Taylor C M, Johnson K L. A theoretical analysis of the isothermal elastohydrodynamic lubrication of concentrated contacts. I. Direction of lubricant entrainment coincident with the major axis of the Hertzian contact ellipse. Proc R Soc Lond Ser A397(1813): 245–269 1985
Vengudusamy B, Enekes C, Spallek R. On the film forming and friction behaviour of greases in rolling/sliding contacts. Tribol Int129: 323–337 2019
Author information
Authors and Affiliations
Corresponding author
Additional information
Balasubramaniam VENGUDUSAMY. He graduated in mechanical engineering and obtained his Ph.D in tribology from Imperial College London, UK. He has been working in the field of tribology for about 15 years. He is currently a senior research tribologist at Klüber Lubrication, Munich.
Claus ENEKES. He studied mechanical engineering at RWTH Aachen University, Germany. Following his interest in tribology, he worked in his Ph.D time on coatings and environmentally friendly lubricants in hydraulic pumps. Since 2012, he is working with Klüber Lubrication München SE & Co. KG, Germany.
Reiner SPALLEK. He is currently working at Klüber Lubrication München SE & Co. KG as the manager of tribology section for the Klüber group. He received his master of mechanical engineering at the University of Frankfurt am Main in Germany. He has been working in the field of tribology for over 24 years.
Electronic Supplementary Material
Rights and permissions
Open Access: This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Vengudusamy, B., Enekes, C. & Spallek, R. EHD friction properties of ISO VG 320 gear oils with smooth and rough surfaces. Friction 8, 164–181 (2020). https://doi.org/10.1007/s40544-019-0267-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40544-019-0267-5