Abstract
Surface roughness is one of the significant index to measure the product quality of the machined parts. The objective of this work is to contribute towards the development of prediction models for surface roughness. In this work, the predictive models were developed for turning operations using soft computing techniques; support vector regression (SVR) and artificial neural network (ANN). The turning experiments are conducted to obtain the experimental data. The developed predictive models were compared using relative error and validated using hypothesis testing. The results indicate that both techniques provide a close relation between the predicted values and the experimental values for surface roughness and are appropriate to predict the surface roughness with significant acceptable accuracy. It is found that ANN performs better as compared to SVR.
You have full access to this open access chapter, Download conference paper PDF
Similar content being viewed by others
Keywords
15.1 Introduction
Predictive modelling is widely used in machining operations to improve the product quality, minimize the production cost and lower the power consumption. Surface roughness is one of the common index to measure the product quality of the machined parts (Sarikaya and Güllü 2014). Surface roughness of machined parts improves the fatigue strength, successive machining benefits, tribological characteristics, quality of fit in two mating parts and corrosive resistance etc. (Kant and Sangwan 2014). Literature depicted that surface roughness is one of the primary performance evaluation criterion in machining operations followed by machining cost and material removal rate (Yusup et al. 2012). The surface roughness of the machined parts depends upon various factors such as cutting parameters, properties of the work piece, cutting tool type and their geometry etc. The theoretical models available in the text books are unable to incorporate the dynamic behavior of the machining operations and failed to predict the surface roughness precisely (Davim et al. 2008). The researchers have used various modelling techniques to overcome the dynamic behavior of machining operations (Garg et al. 2016; Sangwan et al. 2015; Beatrice et al. 2014; Kant and Sangwan 2015a, b, c; Kant et al. 2013; Sangwan and Kant 2017; Pawanr and Garg 2019; Pal and Chakraborty 2005; Aykut Arapo˘glu and Mehmet Alper Sofuo˘glu 2017). Therefore, it is essential to accumulate and analyze the real time experimental data related to surface roughness and control parameters to develop a precise predictive model. In the present study, predictive model for the product quality in terms of surface roughness has been developed using support vector regression (SVR) and artificial neural network (ANN) during turning of mild steel 1045. Sandvik made carbide inserts were used as cutting inserts in a dry cutting environment for the turning operation. The proposed models were compared on the basis of relative error and validated using hypothesis testing.
15.2 Experimental Work
The main objective of this work is to develop predictive models due to which only three machining parameters are considered to simplify the modelling procedure. The turning parameters including cutting speed (\(v\)), feed rate (\(f\)) and cutting depth (\(d\)) and their levels are shown in Table 15.1.
Experiments were conducted on a heavy-duty HMT Centre lathe machine tool having maximum 2300 rpm and 5.5 kW motor rating. Mild steel grade AISI 1045 was selected as a work piece material for the turning because it has wide range of industrial and commercial applications. The carbide cutting inserts of grade TNMG 16 04 04 were used for cutting with tool holder PTGNR 2020K16. The Taylor and Hobson make profilometer was used to acquire the surface roughness data from the work piece. The surface roughness readings were taken on three equally spaced locations and their mean was computed to obtain the average surface roughness. The detailed information of experimental setup, measurements and design of experiment can be seen in reference Kant and Sangwan (2014).
15.3 Development of Predictive Models for Turning
In this section, the obtained experimental data is used to develop the predictive models using SVR and ANN.
15.3.1 Support Vector Regression
An online SVR toolbox for SVR modelling developed by Parrella (2007) in MATLAB is used for predicting the surface roughness. A combined vector of all the three input parameters (v, f, d) as a training set ‘x’ and the training set ‘y’ representing response parameter (surface roughness) is used. Twenty-seven sets of input-output pairs are used for training of the SVR model. The performance of the SVR model majorly depends upon the two variables known as insensitive loss function (ε) and cost function and are adjusted by the users to obtain the best outputs. Training parameters used for this study are ε = 0.01; C = 1000; kernel type = radial basis function (RBF); kernel parameter = 30. SVR checks the verification of Karush–Kuhn–Tucker (KKT) conditions and simultaneously trains the data one by one by adding each sample to the function. If the KKT conditions are not verified then the sample is stabilized using the stabilization technique, else the sample is added. To optimize the values, the stabilization technique dynamically changes the SVR parameters of insensitive loss function and cost function.
15.3.2 Artificial Neural Network
After several trials, it was found that the parameters shown in Table 15.2 leads to accurate results in minimum time.
The network structure 3-7-1 means that it consists of three neurons in the input layer, seven neurons in the hidden layer and output layer with one neuron. 22 random values from the experimental data were chosen for training and five random values were used for testing the network based on selected 80%:20% ratio. A feed forward back propagation algorithm was used to train the network by assigning random weights and biases to interconnected neurons. This algorithm works on the principal of gradient decent method and updates the weights and biases in each iteration until the minimum mean square error is achieved between the target values and training values. The final weights and biases between the input layer and hidden layer are shown in Table 15.3. The weights between hidden layer and output layer are shown in Table 15.4. The bias value between hidden and output layer is 0.491. The neural network was trained using the parameters listed in Table 15.2 and it was observed that mean square error decreased until 250 iterations and after this point it was steady. The training was stopped after 250 iterations and the developed neural network was tested using the random experimental values, which were not used for training process.
15.4 Comparison and Validation of Predictive Models
Equation (15.1) is used to compute the relative errors between the predicted values by the proposed models and their respective experimental values of the surface roughness and are graphically presented in Fig. 15.1.
The average relative errors of 5.17% and 3.07% were found by SVR and ANN respectively.
Mean relative error illustrates that the ANN performs better as compared to SVR. It shows that the well-trained network model can take an optimal performance and has greater accuracy in predicting surface roughness as compared to SVR. Both the techniques are suitable for predicting the surface roughness in an acceptable range. However, the model generation and training procedure of ANN took more time as compared to SVR. Also, both the techniques are appropriate to predict the surface roughness with significant acceptable accuracy. Goodness of fit was calculated and compared for both techniques using some representative hypothetical tests and are shown in Table 15.5. These tests are t-test to test the means, f-test and Levene’s test for variance. In all these tests, the p-values found to be greater than 0.05, which means that the null hypothesis cannot be rejected. The p-values in Table 15.5 also indicate that there is no significant evidence to conclude that the experimental data and the data predicted by SVR and ANN models differ. Therefore, both predictive models have statistically satisfactory goodness of fit for the modelling point of view.
15.5 Conclusions
In this work, predictive models using soft computing techniques SVR and ANN were developed for surface roughness. SVR is capable of accurately predicting the surface roughness during turning operations. The mean relative error between the predicted and experimental values for the SVR model was found to be 5.17%. The predictive model developed using the ANN shows that the surface roughness values could be obtained with the selected ANN parameters. ANN has provided a close relation between the predicted values and the experimental values. The mean relative error for the predicted and experimental values using ANN was found to be 3.07%. It has been found that the model developed using ANN is capable of predicting accurately using a small number of training samples. The developed predictive models are compared using relative error and validated using hypothesis testing. It was found that ANN performs better as compared to SVR. The predictive capability could also be used for automatic monitoring. With the known boundaries of surface roughness and machining conditions, machining could be done with a relatively high rate of success leading to better surface finish.
References
Aykut Arapo˘glu R, Mehmet Alper Sofuo˘glu SO (2017) An ANN-based method to predict surface roughness in turning operations. Arab J Sci Eng 42:1929–1940. https://doi.org/10.1007/s13369-016-2385-y
Beatrice BA, Kirubakaran E, Thangaiah PRJ, Wins KLD (2014) Surface roughness prediction using artificial neural network in hard turning of AISI H13 steel with minimal cutting fluid application. Procedia Eng 97:205–211. https://doi.org/10.1016/j.proeng.2014.12.243
Davim JP, Gaitonde VN, Karnik SR (2008) Investigations into the effect of cutting conditions on surface roughness in turning of free machining steel by ANN models. J Mater Process Technol 205:16–23. https://doi.org/10.1016/j.jmatprotec.2007.11.082
Garg A, Lam JSL, Gao L (2016) Power consumption and tool life models for the production process. J Clean Prod 131:754–764. https://doi.org/10.1016/j.jclepro.2016.04.099
Kant G, Sangwan KS (2014) Prediction and optimization of machining parameters for minimizing power consumption and surface roughness in machining. J Clean Prod 83:151–164. https://doi.org/10.1016/j.jclepro.2014.07.073
Kant G, Sangwan KS (2015a) Predictive modelling and optimization of machining parameters to minimize surface roughness using artificial neural network coupled with genetic algorithm. Procedia CIRP 31:453–458. https://doi.org/10.1016/j.procir.2015.03.043
Kant G, Sangwan KS (2015b) Predictive modeling for power consumption in machining using artificial intelligence techniques. Procedia CIRP 26:403–407. https://doi.org/10.1016/j.procir.2014.07.072
Kant G, Sangwan KS (2015c) Predictive modelling for energy consumption in machining using artificial neural network. Procedia CIRP 37:205–210. https://doi.org/10.1016/j.procir.2015.08.081
Kant G, Rao VV, Sangwan KS (2013) Predictive modeling of turning operations using response surface methodology. Appl Mech Mater 307:170–173. https://doi.org/10.4028/www.scientific.net/AMM.307.170
Pal SK, Chakraborty D (2005) Surface roughness prediction in turning using artificial neural network. Neural Comput Appl 14:319–324. https://doi.org/10.1007/s00521-005-0468-x
Parrella F (2007) Online support vector regression. Thesis in Information Science, University of Genoa, Italy
Pawanr S, Garg GK (2019) Selection of optimum Cutting Parameters for Minimization of Specific Energy Consumption during Machining of Al 6061. J Phys: Conf Ser 1240:012064. https://doi.org/10.1088/1742-6596/1240/1/012064
Sangwan KS, Kant G (2017) Optimization of machining parameters for improving energy efficiency using integrated response surface methodology and genetic algorithm approach. Procedia CIRP 61:517–522. https://doi.org/10.1016/j.procir.2016.11.162
Sangwan KS, Saxena S, Kant G (2015) Optimization of machining parameters to minimize surface roughness using integrated ANN-GA approach. Procedia CIRP 29:305–310. https://doi.org/10.1016/j.procir.2015.02.002
Sarikaya M, Güllü A (2014) Taguchi design and response surface methodology based analysis of machining parameters in CNC turning under MQL. J Clean Prod 65:604–616. https://doi.org/10.1016/j.jclepro.2013.08.040
Yusup N, Mohd A, Zaiton S, Hashim M (2012) Expert systems with applications evolutionary techniques in optimizing machining parameters: review and recent applications (2007–2011). Expert Syst Appl 39:9909–9927. https://doi.org/10.1016/j.eswa.2012.02.109
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Copyright information
© 2020 The Author(s)
About this paper
Cite this paper
Garg, G.K., Pawanr, S., Sangwan, K.S. (2020). A Comparative Analysis of Surface Roughness Prediction Models Using Soft Computing Techniques. In: Sangwan, K., Herrmann, C. (eds) Enhancing Future Skills and Entrepreneurship. Sustainable Production, Life Cycle Engineering and Management. Springer, Cham. https://doi.org/10.1007/978-3-030-44248-4_15
Download citation
DOI: https://doi.org/10.1007/978-3-030-44248-4_15
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-44247-7
Online ISBN: 978-3-030-44248-4
eBook Packages: EngineeringEngineering (R0)