Abstract
The wear of disc cutters significantly impacts the efficiency and cost of TBM operations. In this study, we established a calculation model for radial wear based on the CSM formula and abrasive wear mechanisms. Experimental validation of the wear mechanism confirmed that abrasive wear is the primary mechanism responsible for disc cutter wear. The predictive model was subjected to engineering validation, where the calculated values from the model were compared and analyzed against actual on-site measurements. This validation process confirmed the accuracy and applicability of the model.
You have full access to this open access chapter, Download conference paper PDF
Keywords
1 Introduction
The disc-shaped cutter is a primary component of Tunnel Boring Machines (TBM), and its cutting ring is a consumable part during construction. The cutting ring is prone to wear due to its interaction with the rock surface to be excavated and the crushed rock particles, leading to a decrease in the excavation performance of the disc-shaped cutter. Studying the forces acting on the cutter during rock rolling and assessing the degree of cutter wear are of significant importance for improving the rock-breaking efficiency of the excavation machine and reducing construction costs. Maidl et al. [1] derived an empirical formula relating the average lifespan of 17-in. cutters to the uniaxial compressive strength and the CAI index of the rock by studying various rock properties. Yu et al. [2] established a mapping model between the new cutter health index and specific field parameters based on one-dimensional convolutional neural networks through the analysis and selection of specific parameters from actual construction sites. Estimating the cutter health index provides information about the cutter's wear state. Koppl and Thuro, as well as Koppl et al. [3], developed empirical predictive models for initial and secondary wear of cutting tools caused by abrasive soil erosion. Li et al. [4] validated the stress of cutters in weathered mudstone formations based on the CSM prediction model and concluded that increasing the ratio of penetration rate to effective torque and thrust could reduce cutter wear. Ko et al. [5] studied various TBM cutter prediction models, including the Gehring model, CSM model, and NTNU model, and analyzed their characteristics. The above-mentioned predictive method in the study has a significant margin of error and cannot accurately forecast disc cutter wear. This paper primarily focuses on the positive cutter, and based on abrasive wear mechanisms, calculates the sliding distance through the CSM cutter stress model and cutter motion analysis to establish a calculation model for radial cutter wear. This model facilitates the assessment of wear severity and is validated through wear volume calculations. Therefore, this research is meaningful for guiding the timely replacement of disc-shaped cutters in TBM excavation processes.
2 Force Analysis During Rock Cutting by the Cutter
The stress state of the cutter during rock breaking is depicted in Fig. 1. In Fig. 1, Fn represents the thrust force generated by the TBM propulsion system, while Ft denotes the rolling force induced by the cutterhead torque system. Additionally, when the cutter rotates around the cutterhead center, it also generates a lateral force. However, due to the typically low rotational speed of the cutterhead, the lateral force is usually negligible [6]. When rolling against the rock, in order to balance the effects of Fn and Ft, the rock exerts a reaction force Fr on the cutter, and Fr is one of the primary causes of cutter wear.
The calculation model for Fr is typically based on the (Colorado School of Mines, CSM) CSM model [7], and its expression is as follows:
In the equation, Fr represents the normal reaction force acting on the cutter, \(\psi\) is the distribution coefficient of the cutter's outer edge, \(\phi\) is the contact angle of the cutter, R is the cutter's radius, h represents penetration depth, T is the cutter's blade width, S represents the spacing between cutters, σc is the uniaxial compressive strength of the rock, σt is the uniaxial tensile strength of the rock, C is a dimensionless constant, typically around 2.12, and P0 is the crushing zone pressure, which is related to rock strength and the size and shape of the cutter.
3 Radial Wear Analysis
Among the various failure modes of cutters, wear consumption is the primary reason, and its predominant form is abrasive wear. The degree of cutter wear primarily refers to the change in the cutter ring's radius, and the wear depth of the cutter ring radius is referred to as “radial wear,” which is a crucial criterion for determining whether a cutter needs replacement. For abrasive wear, a simplified model often used is the one proposed by Rabinowicz [8], as shown in Fig. 2.
The calculation formula for Rabinowicz wear is as follows:
In the equation, P represents the applied load, H is the hardness of the metal material, βg is the half-angle of the abrasive grain, Lg is the sliding distance, and ks is the abrasive wear coefficient, which is the product of the abrasive grain's geometric cotβg and the probability constant k. Typically, its value ranges from 10−1 to 10–6 [9].
From Eq. (2), it can be observed that the wear amount is primarily related to the magnitude of the load and the distance traveled. Therefore, based on the stress analysis, calculating the sliding distance of the cutter can yield a more accurate estimation of cutter wear.
3.1 Calculation of Sliding Distance
To achieve the rock-breaking operation of the Tunnel Boring Machine (TBM), the cutterhead is subjected to torque. In addition to revolving around the axis of the cutterhead, the disc cutters mounted on the cutterhead also undergo rotational motion. This, in conjunction with the advancement of the system, allows for penetration into the rock to complete the rock-breaking process. Let \(\omega\) represent the angular velocity of the cutterhead, \(\omega_{0}\) denote the angular velocity of the disc cutter, and ri be the installation radius of the disc cutter. When the disc cutter rotates by an angle \(\phi - \theta\), the relative rotation angle of the cutterhead is \(\varphi\) When the cutter edge is located at position N, the linear velocity generated by the rotation of the disc cutter is:
The linear velocity generated under the effect of the cutterhead's revolution is:
The penetration velocity under the influence of the propulsion system is:
In accordance with the concept of “one-time penetration displacement” as described in Ref. [10], and considering the dynamic variation of the disc cutter position during rock breaking, we establish the coordinate system shown in Fig. 3.
Assuming the sliding distance of the disc cutter within the rock-breaking time t is denoted as L, its components along the x, y, and z axes are as follows:
From the relationship between the rotation of the cutter and the rotation of the cutter, we can get \(\omega_{0} = \omega r_{i} /R\), the relative rotation angle \(R(\phi - \theta ) = r_{i} \varphi\). The relationship between θ and t is \(\theta = \phi - \omega r_{i} t/R\), so the \(d\theta = - (\omega r_{i} /R)dt\) \(d\theta = - (\omega r_{i} /R)dt\) transformed to
Hence, by combining the sliding distances in three directions, the total sliding distance of the disc cutter for one rock-breaking cycle is obtained as follows:
3.2 Calculation of Radial Wear Amount
As shown in Fig. 3, when the disc cutter makes one full rotation from initial contact with the rock to the deepest point of rock breaking at M, the relative rotation angle is φ. Therefore, the integration limits θ2 and θ1 are 0 and φ, respectively. Substituting Eqs. (1) and (8) into Eq. (2), we obtain the volume of wear at the point M from initial contact with the rock to the deepest point of rock breaking as V:
Considering the basic uniformity of the equivalent stress peak values at different points on the cutter ring contact surface, and the relatively stable rotational angular velocity of the disc cutter, it is assumed that the radial wear is consistent at all points on the blade. The expression for the contact area A between the cutter ring and the rock, when the disc cutter completes one rock-breaking cycle, is given by:
Hence, the magnitude of the radial wear amount δ is:
Assuming that the disc cutter completes a certain distance of excavation with Z rotations, the post-wear disc cutter radius is denoted as \(R_{i + 1} = R_{i} - \delta_{i}\), and the blade width as \(T_{i + 1} = T_{i} + 2\delta_{i} \tan \tfrac{\alpha }{2}\), where i represents the number of rotations of the disc cutter (i = 1, 2, 3, … Z), and α is the blade angle. Therefore, the cumulative radial wear amount H after Z rotations is given by:
4 Analysis of Experimental Results
4.1 Wear Mechanism Experiment
In this study, we utilized a disc cutter wear experimental setup to conduct tool wear experiments under different environmental conditions. Through observations using a scanning electron microscope (SEM), we obtained the wear morphology of the tool materials. The wear results indicate that in dry/wet conditions, the primary cause of wear failure in excavation machine tools is abrasive wear. Based on the wear experimental results, this paper derives a formula for calculating tool wear, enabling the prediction and calculation of tool wear. Additionally, Fig. 4 presents the design of the disc cutter rock-breaking simulation experimental setup.
During the rock-breaking process of the tunnel boring machine, in order to reduce the heat generated during rock fragmentation, water spray devices are installed on the disc cutters to achieve cooling and suppress the generation of dust. Utilizing the established disc cutter wear experimental platform, wear tests of the disc cutter materials were conducted with the water spray apparatus. The maximum penetration depth of the disc cutter was set to 2 mm, the rotational speed of the disc cutter specimen was 30 rpm, and granite was chosen as the rock material. The post-wear morphology of the disc cutter is shown in Fig. 5.
From Fig. 5, the wear morphology of the disc cutter material reveals that under dry/wet conditions, abrasive wear predominates on the surface of the disc cutter material. Under dry friction conditions, the wear of the disc cutter material is more severe, and there is a noticeable increase in the width of abrasive particle cutting depth.
Based on the three-dimensional morphology analysis in Fig. 6, it can be observed that the addition of water and similar mediums reduces the wear depth of the disc cutter material, indicating a lubricating effect of water. During the cutting of rock, the disc cutter generates numerous cutting furrows on the contact surface, along with a few occurrences of pits and surface oxidation fatigue wear. Under dry friction conditions, the number of furrows on the disc cutter surface is most pronounced, leading to more severe wear. With the introduction of water, the wear level of the disc cutter material is somewhat alleviated. However, abrasive wear remains the primary wear mechanism, albeit with a reduction in the extent of micro-cutting by rock abrasives.
In summary, abrasive wear is the primary cause of disc cutter wear, and it primarily occurs on the disc cutter surface in the form of micro-cutting.
4.2 Engineering Case Validation
In a construction section of a tunnel within a mountain range in Zhejiang [11], the predominant geological composition of the strata consists mainly of granite and quartzite. The average uniaxial compressive strength of the rock is approximately 110.9 MPa, and the value of kd is taken as 2 × 10–6 mm3/(N mm). There are a total of 9 positive disc cutters installed on the cutterhead. The average penetration depth achieved by one rotation of the disc cutter for rock breaking is 4.12 mm. The arrangement of the disc cutters on the cutterhead is shown in Fig. 7, and the basic parameters of the disc cutters are listed in Table 1.
Figure 8 depicts the relationship between the cutter position number and the wear amount of the positive disc cutters, which was measured after the tunnel boring machine had operated for 471.16 m. As shown in Fig. 8, the predicted values of radial wear amount exhibit a trend that is generally consistent with the actual wear amount. Due to the complex underground construction conditions and factors such as rock anisotropy and joint characteristics, the predicted values may exhibit some errors when compared to actual wear amounts. However, the average error in the calculation results does not exceed 6%, indicating that the established model can reasonably predict the radial wear amount of the disc cutters during their operation.
5 Conclusion
Wear mechanism experiments were conducted using a disc cutter wear test rig, confirming that abrasive wear is the primary mechanism responsible for disc cutter wear. By synthesizing the three movements of disc cutters, namely penetration motion, revolution of the disc cutter, and self-rotation, the sliding distance of the disc cutter after one rotation was determined. This formed the basis for establishing a calculation model for radial disc cutter wear. By inputting actual TBM construction parameters into the predictive model and comparing the results with actual tool wear values, the average error between theoretical values and actual values was within 6%.
References
Maidl B, Schmid L, Ritz W et al (2008) Hardrock tunnel boring machines. Ernst & Sohn
Yu H, Tao J, Huang S et al (2021) A field parameters-based method for real-time wear estimation of disc cutter on TBM cutterhead. Autom Constr 124(4):103603
Koeppl F, Thuro K, Thewes M (2015) Suggestion of an empirical prognosis model for cutting tool wear of hydroshield TBM. Tunn Undergr Space Technol 49:287–294
Li B, Yan Q, Huang J et al (2020) Force and wear patterns of shield machine disc cutters based on the CSM model. China Railw Sci 41(06):91–99
Ko (2014) A comparative study on the TBM disc cutter wear prediction model. J Korean Tunn Undergr Space Assoc 16(6):533
Zhang K, Jia S, Sun J, Zhao H (2019) Study on the impact of blade spacing on the efficiency of disc cutter rock breaking based on ABAQUS. Dev Innov Mach Electr Prod 32(03):55–57
Rostami J, Ozdemir L (1993) New model for performance production of hard rock TBMs. In: Rapid excavation and tunneling conference, June 13–17, 1993. AIME, Boston, pp 793–809
Rabinowicz E, Tanner RI (1966) Friction and wear of materials. J Appl Mech 33(2)
Wang Z, Wang J, Zhang Z et al (2014) Experimental study on the impact factors of disc cutter rock breaking force. J Northeast Univ (Nat Sci) 35(07):1015–1018
Zhang H (2017) Research on the relationship between wear of TBM disc cutters and sliding distance of cutters. Tunnel Constr 37(03):369–374
Tian J (2021) Research on the wear mechanism and rock-breaking characteristics of TBM disc cutters. Jilin University
Acknowledgements
Support from the Liaoning Provincial Natural Fund Program [grant number 2019-KF-04-01] is gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Copyright information
© 2024 The Author(s)
About this paper
Cite this paper
Wang, H., Wei, J., Yan, G., Zhao, H., Xu, J. (2024). Research on TBM Disc Cutter Wear Prediction Based on CSM Model. In: Halgamuge, S.K., Zhang, H., Zhao, D., Bian, Y. (eds) The 8th International Conference on Advances in Construction Machinery and Vehicle Engineering. ICACMVE 2023. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-97-1876-4_48
Download citation
DOI: https://doi.org/10.1007/978-981-97-1876-4_48
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-97-1875-7
Online ISBN: 978-981-97-1876-4
eBook Packages: EngineeringEngineering (R0)