Abstract
In the coolant system of lead-bismuth fast reactor, the corrosion products produce great occupational radiation dose to the workers, especially in the process of maintenance and repair of nuclear facilities. Therefore, it is very important to accurately calculate the corrosion product source term caused by the reaction between coolant and structural materials. The generation, migration, decay and deposition of corrosion products are described by the corrosion characteristics of lead-bismuth alloy on stainless steel in coolant loop, and the mathematical equilibrium equation is established. The equation is used to calculate the corrosion product source term of the coolant loop in the 20MWth lead-bismuth fast reactor and the variation laws of the corrosion product with time are obtained. The results show that the radioactivity of the corrosion products mainly comes from nuclides such as 51Cr, 54Mn, 58Co and 60Co, and the short-lived nuclides such as 51Cr and 58Co decay gradually after shutdown, long-lived nuclides such as 54Mn and 60Co are the main sources of radioactivity.
You have full access to this open access chapter, Download conference paper PDF
Similar content being viewed by others
Keywords
1 Introduction
Lead-bismuth fast reactor is one of the six main types of the fourth generation reactor, which has the characteristics of safety, economy, continuity and nuclear non-proliferation. However, the corrosion ability of lead-bismuth alloy cannot be neglected, and the corrosion products caused by it should not be underestimated. Studies have shown that more than 90% of occupational exposure is caused by corrosion products deposited on the pipe wall from the coolant, which continue to decay and emit gamma rays in the pipe wall or coolant, in particular, some long-life nuclides in the shutdown for a period of time will still cause radiation damage to equipment maintenance workers. Therefore, it is important to study the generation and migration of corrosion products in the alkali metal coolant loop, predict the change and distribution of corrosion products for the radiation shielding design of lead-bismuth fast reactor, the inspection and maintenance of the reactor, and the accident analysis.
In view of the important influence of corrosion products on radiation protection, a great deal of research has been carried out at home and abroad, Such as the PWR-GALE program developed in the United States, the PACTOLE program in France, the Nuclear Power Institute, the Suzhou Thermal Engineering Institute, Tsinghua University, the North China Electric Power University Shanghai Jiao Tong University, and Harbin Engineering University. The above calculation program or method, the principle used is basically the same, but the simplification and assumptions used, as well as the specific treatment methods are not the same. The point reactor model is often used in the calculation, which does not take into account the influence of uneven distribution of neutron flux rate and coolant flow time, so its calculation precision is not high. In addition, the existing source item calculation program has some limitations; the calculation system and equipment are also specific, not universal. At present, the study on source term of corrosion products in water-cooled reactor is mainly focused in China, but there is no systematic study on source term of corrosion products for lead-bismuth coolant.
Based on the characteristics of lead-bismuth reactor coolant loop, the corrosion mechanism of lead-bismuth alloy and the corrosion rate of lead-bismuth alloy, the process of corrosion products generation, decay, migration and deposition in the loop are simulated in this paper; the mathematical equilibrium equation is established. The source term of corrosion products of lead-bismuth coolant was calculated by calculating the fast neutron reaction cross section of the reactor. This study provides reference data for related research in China.
2 Corrosion Source
2.1 Impurities in the Coolant
The impurities in the coolant mainly come from the raw materials and the impurities introduced in the operation. The lead-bismuth alloy was synthesized from lead and bismuth in the ratio of 44.5% and 55.5%, the impurities are mainly non-metallic impurities such as oxygen, carbon, and metallic impurities such as calcium. The pipelines and equipment of the reactor loop are processed, welded and cleaned in the process of manufacture, installation and maintenance, this process inevitably leaves behind some dirt, grease, gasoline, metal chips, welding slag, surface oxides and moisture, which is another major cause of contamination and impurities in the coolant system.
2.2 The Structural Material of the Coolant Channel
Lead and bismuth coolants have the characteristics of high melting point, high boiling point, chemical property inactivity and “Negative” cavitation reactivity. Lead and bismuth are chemically inert with fuels, low alloy steel, water and air. The structural material commonly used in contact with lead-bismuth alloys is stainless steel.
By analyzing the main components and impurities in stainless steel, the possible activation reaction types were determined. Finally, the radionuclide types of various corrosion products, the corresponding reaction types and the main sources of structural materials were counted; the results are shown in Table 1. The common active corrosion products in the main circuit are radionuclide as 24Na, 51Cr, 56Mn, 59Fe, 58Co and 60Co, and their initial nuclides are mainly Fe, Cr, Ni, Mn and Co in the structural materials.
3 Method of Establishment
3.1 Coolant Migration Process
When calculating the source term of corrosion products in the main loop, there are two general conditions. One is that the materials in contact with the coolant in the main circuit are first corroded and dissolved in the coolant; the other is that the material in the core is first activated by radiation, and then corroded down to dissolve in the coolant. As the coolant flows, some of the activated corrosion products in the main circuit will be deposited on the equipment or pipelines in the main circuit, most of which will be cleaned by the purification system, and some will remain in the main circuit coolant. The generation and migration of corrosion product source term in the main loop can be divided into six processes as follows:
-
(1)
The structural material in the core is activated by irradiation;
-
(2)
The material in contact with the coolant in the main circuit is corroded down and dissolved in the coolant to become the corrosion product;
-
(3)
Non-radioactive corrosion products in the coolant flow with the coolant, in the main circuit migration and balance;
-
(4)
The corrosion products in the coolant are irradiated and activated as they flow through the core;
-
(5)
Transfer and equilibrium of radionuclide in the coolant with the coolant flow;
-
(6)
The radionuclide in the coolant precipitates in the main circuit equipment.
3.2 Computational Model
In the coolant loop, the amount of the target radionuclide of the structural material decreases gradually with neutron irradiation.
In the formula, N1 is the nuclear density of the target nucleus in the structural material; t is the time;N2 is the nuclear density of the irradiated radionuclide; σ1 is the average neutron activation cross section of the target nucleus; ϕ1 is the average neutron flux rate of irradiation; λ2 is the decay constant of the irradiated radionuclide.
The increase in radionuclide in the primary circuit due to corrosion of the reactor activated materials at constant reactor power can be calculated as follows:
In the formula, fai is the quality share of the radionuclide in the material; Coj is the material corrosion rate of module j; Sj is the corrosion area of module j; NA is the Amado Avogadro constant; Ai is the atomic weight of radionuclide I; fsILj is the mass share of the nuclide chemical element in the material composition of module j; fnIl is the natural abundance of the target nucleus; λi is the decay constant of radionuclide i.
When the reactor power is constant, the total nucleon number of the activated corrosion products in the coolant changes with time according to the following equation:
If t ≤ t1, the analytical solution of the equation is:
if t > t1, The power of the reactor has changed, the average neutron flux rate of the reactor has changed, The solution of the equation is:
3.3 Example Description
The type of this example is a compact pool structure, as shown in Fig. 1; the main parameters are shown in Table 2. Under normal operating conditions, the circulation flow of lead-bismuth medium in the first circuit is as follows: Lead and Bismuth are heated from bottom to top by the core in the internal components of the reactor, and then enter the upper steam generator of the collector chamber through openings in the upper part of the containment vessel, After the heat transfer is completed from the top to the bottom of the primary side of the steam generator and the secondary side, the secondary side outlet is reintegrated into the lower collecting cavity of the side shield, and the inner opening of the side shield returns to the upper collecting cavity from the bottom to the top, Then flow down the annular passage between the side shield and the main vessel and enter the main pump inlet, under the pumping of the main pump, the annular passage between the lower shield and the lower head of the main vessel enters the lower collecting cavity of the core along the flow distribution mechanism, and finally returns to the core.
3.4 Calculation Results and Comparative Analysis
The fast neutron average reaction cross sections for various reactions were calculated using the MCNP code, as shown in Table 3. The radioactivity of the corrosion products in the model coolant is calculated using the formula in Sect. 3.2, and a comparison with the results of the same type of reactor is shown in Table 4.
As can be seen from Table 4, the total activity of corrosion products in the lead-bismuth coolant circuit is 1.97E+15Bq. Among them, 51Cr, 54Mn, 58Co and 60Co have the largest proportion, but 51Cr and 58Co are short-lived nuclides, which can decay rapidly after shut down for a period of time, and 54Mn and 60Co have longer lifetime, which are the main contributors to the total activity.
Compared with ClEAR-1, the model has same life, but different power, temperature, flow, and structural materials. These factors cause the total amount of corrosion products to be more than ClEAR-1.
4 Conclusions
The sediment source term of corrosion products is the main source of occupational irradiation, and it is also the key and difficult point in the source term analysis of nuclear facilities. Based on the characteristics of lead-bismuth coolant system, the release, migration, decay and deposition of corrosion products in the coolant loop are fully considered, a method for calculating the source term of corrosion products in lead-bismuth coolant loop is developed, The method is used to simulate the coolant loop of lead-bismuth fast reactor, and the source term of corrosion products is calculated. The results show that the source terms of the corrosion products are mainly composed of 51Cr, 54Mn, 56Mn, 58Co, 60Co and 59Fe, among which the long-lived nuclides 60Co and 54Mn are the main contributors to the radioactive activity. The analytical methods and conclusions of this paper can provide theoretical support for relevant domestic research.
References
Wu, Y., et al.: Conceptual design of China lead-based research reactor CLEAR-1. Nucl. Sci. Eng. 6 (2014)
Chandrasekaran, T., Lee, J.Y., Willis, C.A.: Calculation of Releases of Radioactive Materials in Gaseous and Liquid Effluents from Pressurized Water Reactors. Division of Systems Integration Office of Nuclear Reactor Regulation U.S. Nuclear Regulatory Commission, Washington, D.C (1985)
Dacquait, F., Nguyen, F., Martean, H.: Simulations of Corrosion Product Transfer with the PACTOLE V3.2 Code
Zhang, C.: Source terms calculation analysis for the reactor and primary coolant system of Qinshan Phase II NPP project. Nucl. Power Eng. 24, 73–77 (2003)
Ding, S., Shangguan, Z., Tao, Y.: Study on computational models of secondary source terms for normal operation of CPR1000 Nuclear Power Plants. Radiat. Protect. 29 (2009)
Liu, Y.: Calculation method and computer program for radionuclide concentration in primary circuit of light water reactor. Radiat. Protect. (1986)
Liu, Z., et al.: Source team analysis of DORAST code used in AP1000 primary and secondary coolant system. Atomic Energy Sci. Technol. 47, 625–629 (2013)
Wu, M.: Study on Radiation Source Term of Main Coolant in Nuclear Power Plant. Shanghai Jiao Tong University (2005)
Yang, Y., et al.: Analysis of dose field in marine reactor cabin. Nucl. Sci. Eng. (2014)
Goorley, T., Bull, J., Brown, F., et al.: Release of MCNP 5_RSICC_1.30, Los Alamos National Laboratory (2004)
Gang, T.: Study on Radioactive Source Term and Dose Assessment for Lead-Bismuth Cooled Reactor (2013)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Copyright information
© 2023 The Author(s)
About this paper
Cite this paper
Wan, H. (2023). Study on Calculation Method of Corrosion Product Source Term in Lead-Bismuth Fast Reactor Coolant System. In: Liu, C. (eds) Proceedings of the 23rd Pacific Basin Nuclear Conference, Volume 1. PBNC 2022. Springer Proceedings in Physics, vol 283. Springer, Singapore. https://doi.org/10.1007/978-981-99-1023-6_55
Download citation
DOI: https://doi.org/10.1007/978-981-99-1023-6_55
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-1022-9
Online ISBN: 978-981-99-1023-6
eBook Packages: Physics and AstronomyPhysics and Astronomy (R0)