Abstract
Nanographite (NG) is a promising conductive filler for producing effective electrically conductive cementitious composites for use in structural health monitoring methods. Since the acceptable mechanical strength and electrical resistivity are both required, the design of NG-based cementitious composite (NGCC) is a complicated multi-objective optimization problem. This study proposes a data-driven method to address this multi-objective design optimization (MODO) issue for NGCC using machine learning (ML) techniques and non-dominated sorting genetic algorithm (NSGA-II). Prediction models of the uniaxial compressive strength (UCS) and electrical resistivity (ER) of NGCC are established by Bayesian-tuned XGBoost with prepared datasets. Results show that they have excellent performance in predicting both properties with high R2 (0.95 and 0.92, 0.99 and 0.98) and low mean absolute error (1.24 and 3.44, 0.15 and 0.22). The influence of critical features on NGCC’s properties are quantified by ML theories, which help determine the variables to be optimized and define their constraints for the MODO. The MODO program is developed on the basis of NSGA-II. It optimizes NGCC’s properties of UCS and ER simultaneously, and successfully achieves a set of Pareto solutions, which can facilitate appropriate parameters selections for the NGCC design.
You have full access to this open access chapter, Download conference paper PDF
Keywords
1 Introduction
Nanographite (NG) is a promising conductive filler for producing highly effective electrically conductive cementitious composites. As reported by [1], the NG-based cementitious composite (NGCC) has efficient strength and conductivity as a self-sensing construction material for use in non-destructive structural health monitoring (NDSHM). There are generally three forms of NG studied in NGCC, namely graphene nanoplatelet (GNP), graphene oxide (GO), and reduced GO (rGO). Apart from the form of NG used, as well as its physical properties, it has been confirmed that other experimental factors, such as the dispersion of NG and curing condition, are linked to the strength and conductivity variations of NGCC [2, 3]. Significant experimental research has been conducted to determine the optimal values for those factors during the production of NGCC [4, 5].
The purpose of design optimization of NGCC is to approach its high strength and low electrical resistivity (ER) simultaneously, which can seem difficult to realize by experimental methods. Once, an experiment could only consider one factor with limited design values for variable-controlling analysis, making the design experience lack universality. Former experimental studies often discussed mechanical and electrical objectives separately. Nevertheless, they have provided numerous test data. We present our study that aimed to address the multi-objective design optimization (MODO) problem of NGCC using advanced data mining techniques.
The study proposed a comprehensive data-driven computing and analyzing method, which integrates algorithms of machine learning (ML) and non-dominated sorting genetic algorithm (NSGA-II). First, the uniaxial compressive strength (UCS) and ER of NGCC were modelled by Bayesian-optimized XGBoost with compiled experimental datasets. During the modelling process, the Weight and SHAP (SHapley Additive exPlanations) theories were used to interpret the ML models and determine variables that were critical for optimization. Furthermore, the established models worked as objective functions in NSGA-II to develop the MODO program. The feasibility and accuracy of the proposed MODO method are discussed and proved with a case study. Using this method, researchers can quickly find the optimal designs of NGCC that satisfy their application demands.
2 Methods
2.1 Establishment of Calculation Models
We modelled the UCS and ER of NGCC through a complex ML modelling framework, as shown in Fig. 1, to ensure the established models were accurate and reliable. The framework followed four steps. Original experimental datasets of UCS and ER were constructed after an extensive literature review. They were then processed with proper feature engineering strategies before estimator training. In Step 3 of modelling, we applied four classic ML algorithms, namely support vector regressor (SVR), random forest regressor (RFR), XGBoost, and back-propagation neural network (BPNN), to the processed datasets. Three searching methods, comprising grid searching (GS), particle swarm optimization (PSO), and Bayesian optimization (BO), were used to tune the hyperparameters of the algorithms for achieving their best performance. At this stage, estimators based on four algorithms were compared with each other to determine the most suitable models for UCS and ER. Finally, we used SHAP theory to interpret the established models to identify critical input variables and quantify their influence.
2.2 Development of the MODO Program
Figure 2 shows the workflow of the developed MODO program. The structure of the program was based on the mechanism of NSGA-II. Individuals in the generated group were vectors consisting of variables to be optimized. Lower and upper boundaries should be defined for each variable. Other variables that were also considered in both datasets were fixed. Afterwards, the generated group concatenated fixed variables to form the input datasets for UCS and ER calculations using the established models. Pipelines were tools packing feature engineering methods and making the format of input datasets consistent. Individuals were ranked based on the UCS and ER results according to the Pareto rule. Individuals in the high Pareto ranks and with larger crowding distances were kept for creating the next generation group. At the end of the program, the final group was the Pareto set formed with optimal design solutions.
3 Results and Discussion
Bayesian-optimized XGBoost models proved the most suitable for the UCS and ER of NGCC according to the comparative results, and their hyperparameter combinations are given in Table 1. Models had minimal gaps between training and testing subsets at the end of the training, indicating no over- or under-fitting issues. Mean absolute error (MAE) and determination coefficient (R2) were two indexes for assessing the accuracy of the established models. Small MAE values (1.24 and 3.44, 0.15 and 0.22) and high R2 scores (0.95 and 0.92, 0.99 and 0.98) of the two models yielded satisfactory and reliable prediction abilities for the UCS and ER of NGCC. Figure 3 shows the feature importance ranking based on the SHAP interpretation results of the two models. It can be seen that the UCS and ER prediction models share almost the same feature importance ranking, where the mixing amount of NG (GC) was a dominant variable in both properties. The high influence could also be observed in other features: NG’s physical properties of thickness and diameter (GT and GD), the water dosage and curing age.
The developed MODO program proved feasible in a case study. In the case study, GNP was selected and the curing age was set at 28 days while the other six variables were optimized. The optimization process is recorded in Fig. 4 and the program successfully converged to the final Pareto set through iteration. As listed in Table 2, optimization results indicated that all the given design solutions qualified for the NDSHM application with acceptable strength and conductivity. Higher UCS led to higher ER (lower conductivity). Additionally, optimal values could be found for some variables. For example, the ideal thickness of GNP was ≈6.36 nm. The water/cement ratio was 0.32 in most solutions. The ultrasonication process for GNP dispersion was better if it lasted for 30 min. The differences in output results between solutions were mostly due to the changes in the dosage of sand and GNP, as well as the GD. UCS and ER of NGCC became smaller by adding more GNP.
4 Conclusions
Robust and reliable calculation models were established for the UCS and ER of NGCC by BO-tuned XGBoost. The SHAP interpretation results of the established models identified significant influential factors, including NG dosage and other variables. Moreover, we explained their quantitative influence on the properties of NGCC by analyzing their SHAP value distributions. NSGA-II was combined with the established models as objective functions to develop the MODO program of NGCC. The program proved feasible through a case study in which it successfully obtained the Pareto set of design solutions. The given solutions determined the optimal values for some variables.
References
Qureshi TS, Panesar DK (2019) A comparison of graphene oxide, reduced graphene oxide and pure graphene: early age properties of cement composites. In: Proceedings of the International Conference on Sustainable Materials, Systems and Structures (SMSS2019) New Generation of Construction Materials. vol 1
Wotring EE (2015) Dispersion of graphene nanoplatelets in water with surfactant and reinforcement of mortar with graphene nanoplatelets. University of Illinois at Urbana-Champaign, Master’s Theses
Liu J, Fu J, Yang Y, Gu C (2019) Study on dispersion, mechanical and microstructure properties of cement paste incorporating graphene sheets. Constr Build Mater 199
Sun S, Han B, Jiang S, Yu X, Wang Y, Li H, Ou J (2017) Nano graphite platelets-enabled piezoresistive cementitious composites for structural health monitoring. Constr Build Mater 136
Li X, Liu YM, Li WG, Li CY, Sanjayan JG, Duan WH, Li Z (2017) Effects of graphene oxide agglomerates on workability, hydration, microstructure and compressive strength of cement paste. Constr Build Mater 145
Acknowledgements
We appreciate the support of The University of Western Australia through the “Scholarship for International Research Fees and Ad Hoc Postgraduate Scholarship”. The research work was financially supported by the ARC Research Hub for Nanoscience-Based Construction Material Manufacturing (IH150100006). Experimental data used in machine learning modelling in this study were retrieved from published literature and all data sources are acknowledged.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Copyright information
© 2023 The Author(s)
About this paper
Cite this paper
Dong, W., Huang, Y., Lehane, B., Ma, G. (2023). An Intelligent Multi-objective Design Optimization Method for Nanographite-Based Electrically Conductive Cementitious Composites. In: Duan, W., Zhang, L., Shah, S.P. (eds) Nanotechnology in Construction for Circular Economy. NICOM 2022. Lecture Notes in Civil Engineering, vol 356. Springer, Singapore. https://doi.org/10.1007/978-981-99-3330-3_35
Download citation
DOI: https://doi.org/10.1007/978-981-99-3330-3_35
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-3329-7
Online ISBN: 978-981-99-3330-3
eBook Packages: EngineeringEngineering (R0)