Abstract
Determining the graphene oxide (GO) content is the key to applying GO to reinforce the mechanical performance and durability of cementitious composites. However, most of the previous studies are conducted from the perspective of experiments and lack elaboration on the mechanism of the GO-reinforced cementitious composite under different GO content. Hence, we investigated the effect of GO content on the reinforcing efficiency of calcium–silicate–hydrate (C–S–H) to trade off the enhancement of GO in cementitious composites and the corresponding economic benefits. The results demonstrated that an appropriate number of GO nanosheets can reinforce the cementitious composite with simultaneous high enhancing efficiency and economic benefits. The microdamage evolution of GO/C–S–H composites and the GO reinforcing mechanisms are reported. Our findings deepen the understanding of the enhancing mechanisms of GO embedded in C–S–H nanocomposites and help to determine the suitable GO content in practical engineering.
You have full access to this open access chapter, Download conference paper PDF
Keywords
1 Introduction
By virtue of superior mechanical properties, ultra-high specific area and abundant oxygen-containing functional groups, graphene oxide (GO) exhibits outstanding performance in optimizing the microstructure [1], improving mechanical properties [2], enhancing permeability resistance [3], increasing durability [4], and improving the thermal and electrical conductivity [5] of cement-based materials through nucleation effects [6] and pore-infilling effects [7]. Furthermore, some latest studies indicate that graphene-based enhancement of cementitious composites could be a cost-effective strategy for decreasing CO2 emissions and energy consumption in practical engineering [8].
The concentration of GO sheets significantly influences the mechanical performance of cement-based grouting materials when they are incorporated into the cementitious material. In the past study, researchers have primarily determined the proportion of GO with the help of experiments and experience [2]. There are few studies on the mechanism of composite enhancement by different ratios of GO. Hence, to better understand the regulatory effect of GO on calcium–silicate–hydrate (C–S–H) gel, it is necessary to understand the effect of different mixing concentrations of GO sheets on the mechanical properties of C–S–H gels. Therefore, in this study, we built a molecular dynamics (MD) model with different ratios of GO nanolayers incorporated into the C–S–H nanocomposite, and performed tensile tests to investigate the effects of the GO content on the reinforcing efficiency of C–S–H composites and the enhancing mechanism.
2 Methods
Following a previous study [9] and using the same model parameters of GO and C–S–H gel, GO/C–S–H nanocomposites were built in which one or two parallel GO nanolayers were embedded in the C–S–H matrix and the spatial orientation of the sheets was aligned with the \(x\) direction (Fig. 1). The whole system was firstly relaxed for 2 ns in the NPT ensemble at 300 K and 0 atmosphere to achieve equilibrium. Next, tensile deformation was applied to the nanocomposite with a stretching rate of 1 m/s. The NPT ensemble was applied in the \(y\) and \(z\) directions during the tensile deformation at 300 K and 0 atmosphere. The tensile process was completed when the tensile strain in the \(x\) direction reached 110%. The C–S–H gel was described by the CLAYFF force field [10] and GO was described by the consistent-valence forcefield [11], with a cutoff radius of 1.5 nm for both Lennard–Jones 12–6 potential and Coulomb electrostatic potential. The intermolecular force between the C–S–H gel and GO nanolayer was described by the Lennard–Jones 12–6 potential and Coulomb electrostatic potential, and the corresponding parameters were derived by the Lorentz–Berthelot combining rules. The time step was set as 0.5 fs and the long-range electrostatic interactions were resolved by the particle–particle–particle-mesh method.
3 Results and Discussion
3.1 Tensile Mechanical Properties of the GO/C–S–H Model
The ultimate tensile strength of the MD system did not change significantly after embedding different numbers of GO nanosheets, and the tensile stress–strain curves are presented in Fig. 2. Similar to the visible test results [2], when the MD model reached its peak strength, some damage was generated inside the C–S–H model, but the C–S–H model still had a certain amount of residual strength until its complete failure after further stretching. The monolayer GO/C–S–H model underwent damage at a tensile strain of 0.5. By contrast, the tensile ductility of the bilayer GO/C–S–H model was significantly enhanced to 0.9, with an enhancement ratio of 80%.
3.2 Failure Process of GO/C–S–H Models Under Stretching
In order to reveal the enhancement mechanism of GO incorporated into C–S–H, typical atomic model images (Fig. 3) during stretching were selected to display the microdamage evolution of the C–S–H models with different GO layers embedded. Figure 3 shows that the deformation of the GO/C–S–H model can be divided into the following stages: structural loosening stage, pore development stage, and failure stage.
In the monolayer GO/C–S–H model, the C–S–H structure loosened as the tensile strain reached 0.2. As the tensile strain increased to 0.5, noticeable pores began to appear in the structure, but there was still a certain amount of bridging C–S–H, so the model was still a monolithic structure. As the tensile strain continually increased to 0.6, the C–S–H completely separated and fractured, consistent with Fig. 2. At the same time, the molecular structure of the bilayer GO/C–S–H model slowly started to be loosen. Pores gradually appeared and expanded when the strain increased from 0.6 to 1.1. At this time, the C–S–H gel still had residual strength and ability to resist tensile deformation. In addition, it was not hard to find that with increasing deformation, the molecular structure around the GO nanosheets became more closely arranged, especially the C–S–H molecules sandwiched between the two GO layers. It can be concluded that the ductility of the C–S–H was greatly improved with the addition of two GO nanolayers compared with the intercalation of a single layer of GO. Our results also proved that an appropriate amount of GO can effectively enhance the stretching mechanical performance of cement-based materials.
4 Conclusions
The effects of incorporating different numbers of layers of GO nanosheets on the tensile performance of C–S–H gels were studied by MD simulations, the microdamage evolution of GO/S–H models in the tensile process were investigated, and the enhancement mechanism of GO on the tensile properties of hydrated calcium silicate composites was analyzed at the atomic scale. Our main conclusions are listed below.
-
(1)
Incorporating an appropriate amount of GO was able to effectively improve the ductility of hydrated calcium silicate composites. MD simulations showed that the bilayer GO/C–S–H model increased the post-peak plastic strain by 80% compared with a monolayer GO/C–S–H model.
-
(2)
The deformation of the GO/C–S–H model can be divided into structural loosening stage, pore development stage, and failure stage. Compared with the monolayer GO/S–H model, the strain values corresponding to the bilayer GO model entering the third stage were delayed.
-
(3)
At the atomic scale, the structure of C–S–H around the GO nanosheets was more compact, showing a higher ability to resist tensile deformation, and also reflected the enhancement effect of an appropriate amount of GO on the mechanical properties of C–S–H composites.
References
Zhang C, Zhu Z, Wang W, Shao L, Wan Y, Huo W (2022) Mechanical properties and micro-structure of expansive soil stabilized by graphene oxide modified cement
Pan Z, He L, Qiu L, Korayem AH, Li G, Zhu JW, Collins F, Li D, Duan WH, Wang MC (2015) Mechanical properties and microstructure of a graphene oxide–cement composite. Cement Concr Compos 58:140–147
Chen X, Zhang Y, Li S, Geng Y, Hou D (2021) Influence of a new type of graphene oxide/silane composite emulsion on the permeability resistance of damaged concrete. Coatings 11:208
Devi S, Khan R (2020) Effect of graphene oxide on mechanical and durability performance of concrete. J Build Eng 27:101007
Yang H, Monasterio M, Cui H, Han N (2017) Experimental study of the effects of graphene oxide on microstructure and properties of cement paste composite. Compos A Appl Sci Manuf 102:263–272
Li W, Li X, Chen SJ, Liu YM, Duan WH, Shah SP (2017) Effects of graphene oxide on early-age hydration and electrical resistivity of Portland cement paste. Constr Build Mater 136:506–514
Gao Y, Jing HW, Chen SJ, Du MR, Chen WQ, Duan WH (2019) Influence of ultrasonication on the dispersion and enhancing effect of graphene oxide–carbon nanotube hybrid nanoreinforcement in cementitious composite. Compos B Eng 164:45–53
de Souza FB, Yao X, Gao W, Duan W (2022) Graphene opens pathways to a carbon-neutral cement industry. Sci Bull 67:5–8
Gao Y, Jing H, Wu J, Fu G, Feng C, Chen W (2022) Molecular dynamics study on the influence of graphene oxide on the tensile behavior of calcium silicate hydrate composites. Mater Chem Phys:126881
Cygan RT, Liang J-J, Kalinichev AG (2004) Molecular models of hydroxide, oxyhydroxide, and clay phases and the development of a general force field. J Phys Chem B 108:1255–1266
Dauber‐Osguthorpe P, Roberts VA, Osguthorpe DJ, Wolff J, Genest M, Hagler AT (1988) Structure and energetics of ligand binding to proteins: Escherichia coli dihydrofolate reductase‐trimethoprim, a drug‐receptor system. Proteins Struct Funct Bioinf 4:31–47
Acknowledgements
This study was supported by the Zhejiang Provincial Natural Science Foundation of China (No. LQ21E040003).
Funding
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Author information
Authors and Affiliations
Contributions
The manuscript was written through contributions of all authors. All authors have given approval to the final version of the manuscript.
Corresponding authors
Editor information
Editors and Affiliations
Rights and permissions
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Copyright information
© 2023 The Author(s)
About this paper
Cite this paper
Chen, W., Xiang, J., Gao, Y., Zhang, Z. (2023). Effects of Graphene Oxide Content on the Reinforcing Efficiency of C–S–H Composites: A Molecular Dynamics Study. In: Duan, W., Zhang, L., Shah, S.P. (eds) Nanotechnology in Construction for Circular Economy. NICOM 2022. Lecture Notes in Civil Engineering, vol 356. Springer, Singapore. https://doi.org/10.1007/978-981-99-3330-3_55
Download citation
DOI: https://doi.org/10.1007/978-981-99-3330-3_55
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-3329-7
Online ISBN: 978-981-99-3330-3
eBook Packages: EngineeringEngineering (R0)