Abstract
Tropospheric delay modeling is challenging in high-precision Very Long Baseline Interferometry (VLBI) analysis due to the rapid water vapor variation and imperfect observation geometry, where observations from Global Navigation Satellite Systems (GNSS) co-locations can enhance the VLBI analysis. We investigate the impact of tropospheric ties in the VLBI and GNSS integrated processing during the CONT05–CONT17 campaigns, and present a method that automatically handles the systematic tropospheric tie biases. Applying tropospheric ties at VLBI–GNSS co-locations enhances the observation geometry and improves the solution reliability. The VLBI network is stabilized, with station coordinate repeatability improved by 12% horizontally and by 28% vertically, and the network scale improved by 32%. The Earth Orientation Parameters (EOP) improve by up to 20%. Both zenith delay and gradient ties contribute to the improvement of EOP, whereas the gradient ties contribute mainly to the improvement of length of day and celestial pole offsets.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
For the microwave-based space geodetic techniques, such as Very Long Baseline Interferometry (VLBI) and Global Navigation Satellite Systems (GNSS), the signals transmitted through the electrically neutral atmosphere are delayed due to the non-vacuum conditions, causing the tropospheric delay (Böhm and Schuh 2013). Modeling the time-varying tropospheric delay to achieve high-precision space geodesy is challenging due to the rapid spatial and temporal variation of its wet component and the correlation between tropospheric delay and station coordinates and clocks, especially between zenith total delay (ZTD) and the station vertical component. As VLBI is the only technique capable of determining the full set of Earth Orientation Parameters (EOP) and contributes to the determination of the network scale of the International Terrestrial Reference Frame (ITRF) (Altamimi et al. 2016; Bizouard et al. 2018), persistent efforts have been put to improve VLBI solutions. However, due to the fact that at least two VLBI radio telescopes must observe the same radio source simultaneously, the limited observation number and imperfect observation geometry present disadvantages for VLBI-only studies.
To de-correlate station coordinates and tropospheric parameters, precise external tropospheric information can be used, including water vapor radiometer (Kuehn et al. 1991; Nilsson et al. 2017a, b), Numerical Weather Models (NWMs) (Hobiger et al. 2010; Eriksson et al. 2014; Hofmeister and Böhm 2017), or precise estimates from an independent space geodetic technique, such as GNSS. GNSS provides precise tropospheric information with good temporal resolution and a ZTD accuracy of 4 mm (Bender et al. 2008) due to the continuous tracking and well distributed observation geometry. Thus, it has been widely used to enhance other microwave-based space geodetic techniques, such as satellite altimetry (Fernandes et al. 2015) and Interferometric Synthetic Aperture Radar (InSAR) (Williams et al. 1998; Shamshiri et al. 2020). At co-location sites that typically extend hundreds of meters, VLBI and GNSS can be assumed observing through the same troposphere. Thus, the tropospheric zenith delays and horizontal gradients can be combined after considering the effects of station coordinate differences on tropospheric parameters, that is, the tropospheric ties. Applying tropospheric ties allows to consider more observations and improves the observation geometry, leading to a better precision of tropospheric parameters. Through inter-parameter correlations, other parameters can be improved in turn, including station positions and EOP, especially those of the VLBI solution that suffer more from the limited geometry.
Applying tropospheric ties to GNSS co-locations can improve the UT1-UTC (dUT1) accuracy of the International VLBI Service for Geodesy and Astrometry (IVS) 1-h Intensive sessions to overcome the deficiency of poor geometry (Teke et al. 2015; Nilsson, et al. 2017a, b). The IVS 24-h sessions also benefit from tropospheric ties to GNSS co-locations (Krügel et al. 2007; Hobiger and Otsubo 2014; Diamantidis et al. 2021), where station coordinates improve. However, most of these studies use different software for the VLBI and GNSS processing. Despite the great efforts in pursuing homogeneous processing strategies, the inter-software inconsistency inevitably causes tropospheric delay discrepancy and degrades the solution. More importantly, the tropospheric tie might present systematic biases even after applying the height-related corrections, which can reach up to 5 mm for ZTD. Ignoring them may distort the VLBI network and cause systematic biases in the VLBI estimates. Moreover, these studies mainly focus on the station coordinates, whereas the impact on global geodetic and geophysical parameters, including the network scale and EOP, has not been fully investigated.
The current ITRF determination by combining different space geodetic techniques utilizes the global ties, that is, EOP, and local ties on station coordinates at co-location sites as well as co-motion constraints. Additionally applying tropospheric ties will very likely be an important step forward in ITRF determination. Considering the high number of parameters, combining tropospheric parameters has a large potential to improve the precision and reliability, and to contribute to validating the local ties (Krügel et al. 2007). The combination on the observation level can also improve the consistency and reliability of the future determination of reference frames and EOP.
In this study, we investigate the impact of applying tropospheric ties at VLBI–GNSS co-location sites based on the five IVS Continuous VLBI Campaigns (CONT) between 2005 and 2017. We process the VLBI and GNSS observations simultaneously in the same software package, that is, integrated processing on the observation level, to ensure the highest consistency. Furthermore, we adopt an automatic method to handle the tropospheric tie biases. We demonstrate the effects of ZTD and gradient ties on station coordinates, network scale, and EOP individually.
2 Data and methods
2.1 The VLBI CONT campaigns
Unlike GNSS where daily observations are usually processed in the 00:00–24:00 UT datasets, the 24-h global VLBI observing sessions are usually discontinuous and start around 17:00–18:30 UT. However, the 24-h sessions available in the five CONT campaigns start at 00:00 UT, named with the year carried out as CONT05, CONT08, CONT11, CONT14, and CONT17, with 15 sessions in each campaign. It should be noted that the CONT05 sessions started observing at 17:00, but a reprocessed version (the XB series) starting at 00:00 is also provided by IVS and used in this study. The CONT05B series has 14 instead of 15 sessions. The CONT campaigns using more radio telescopes and radio sources aim on demonstrating the best capability of VLBI at that time on both technical and scientific perspectives (Behrend et al. 2020). Therefore, they are ideal for inter-technique comparisons and multi-technique combinations (Thaller et al. 2006; Teke et al. 2013; Hobiger and Otsubo 2014; Pollet et al. 2014; Heinkelmann et al. 2016). The geographical distribution of the network stations of the CONT05–CONT17 campaigns used in this study is presented in Fig. 1.
Figure 1 also shows the co-locations with the International GNSS Service (IGS) stations, which are available at most VLBI stations. We use all available GNSS co-locations to improve the observation geometry and to alleviate potential instrument-related systematic biases.
The GNSS–VLBI inter-station distances are provided in Table 1. For most of the co-locations, the horizontal distances are within 200 m, and the vertical distances are within 20 m. The two exceptions are: MDO1–FD-VLBA, 8 km horizontally and around 400 m vertically; HARB–HART15M/HARTRAO, 2 km horizontally and around 150 m vertically. Despite this relatively large inter-station distance, the inter-technique agreement of tropospheric parameters at these two co-locations is not larger than that of other co-locations. For MDO1–FD-VLBA, the STD value of ZTD differences in CONT17-VLBA is 4.1 mm, and the RMS values of the north and east gradient differences are 0.6 and 0.4 mm, respectively. As for HARB–HART15M/HARTRAO, the STD value of ZTD differences varies between 3.8 and 6.8 mm, and the RMS value of north and east gradients varies between 0.5 and 1.6 mm, during CONT05 to CONT17. For all the co-locations during CONT05 and CONT17, the average value is 4.0 mm for ZTD STD, 0.7 mm for north gradient, and 0.6 mm for east gradient. Therefore, the tropospheric ties at MDO1–FD-VLBA and HARB–HART15M/HARTRAO co-locations can be applied.
2.2 Integrated processing of GNSS and VLBI on the observation level
For the multi-technique integrated processing on the observation level, the VLBI module was newly implemented in the Positioning And Navigation Data Analyst (PANDA) software (Liu and Ge 2003). The PANDA software focusing on high-precision GNSS data processing is widely used in geodetic applications, including satellite orbit determination (Liu et al. 2016; Huang et al. 2020), static and kinematic platform positioning (Penna et al. 2018; Wang and Liu 2019; Abbaszadeh et al. 2020), atmospheric sensing (Wang et al. 2019; Wu et al. 2020). The VLBI module was implemented in a common least-squares estimator with GNSS (Wang 2021), following the IERS Conventions 2010 (Petit and Luzum 2010).
We processed VLBI and GNSS observations simultaneously on a daily basis. The data processing strategy is present in Table 2. The a priori EOP were derived from the IERS Bulletin A product, and the station displacements include solid Earth tides, ocean tidal displacements, pole tide loading, ocean pole tide loading, and tidal atmospheric pressure loading. Non-tidal atmospheric pressure loading (Männel et al. 2019) was also applied using the VMF product (Wijaya et al. 2013).
We processed VLBI X-band group delay observations that were corrected for dispersive delays employing the S-band observations for mitigating the ionospheric refraction. We estimated daily constant station coordinates applying minimum datum constraints (Glaser et al. 2015) to ITRF2014 (Altamimi et al. 2016). The radio source coordinates were fixed to ICRF3 (Charlot et al. 2020). Both, offsets and rates of polar motion (PM) and UT1-UTC were estimated, whereas celestial pole offsets (CPO, dX and dY) were determined as daily constants. We used the random walk process to model station clocks with a stochastic noise of 0.3 \({\text{mm}}/\sqrt {\text{s}}\), and clock breaks and baseline clock offsets where indicated.
We processed the GNSS ionosphere-free combined pseudo-range and phase observations in the static Precise Point Positioning (PPP) mode (Zumberge et al. 1997), with satellite orbits and clocks fixed to IGS products (Johnston et al. 2017; Griffiths 2018). We estimated GNSS receiver clocks as epoch-wise white noise, and corrected antenna phase center offsets and variations (Rebischung and Schmid 2016), phase wind up (Wu et al. 1993), and relativity effect. Note that in PPP mode GNSS observations do not contribute to the EOP estimation.
2.3 Applying the tropospheric ties
For both VLBI and GNSS, the tropospheric delay \(L\left( {e,\alpha } \right)\) in slant direction with elevation \(e\) and azimuth \(\alpha\) can be described as
where \({\text{ZHD}}\) and \({\text{ZWD}}_{0}\) denote the a priori zenith hydrostatic and wet delays, respectively; \(mf_{{\text{h}}} \left( e \right)\) and \(mf_{{\text{w}}} \left( e \right)\) are corresponding mapping functions. \(G_{{\text{N}}}\) and \(G_{{\text{E}}}\) are the north and east total gradients, respectively, and \(mf_{{\text{g}}} \left( e \right)\) is the gradient mapping function. The residual non-hydrostatic delay \(\Delta {\text{ZWD}}\) is parametrized as one-hourly piece-wise-constant (PWC), and both gradients are estimated as three-hourly PWC.
The same tropospheric parameters, that is, the residual ZWD and gradients, were applied to both VLBI and GNSS stations at the co-locations, considering the topography-related (mainly in the altitude component) and instrument-related differences. We used the VMF3 station-based product (Landskron and Böhm 2017, 2018) for the a priori zenith delays and mapping functions, which can efficiently cancel the topography-related difference. As the station-based VMF3 does not always refer to the height of the reference point of the GNSS antenna, an empirical equation was applied to correct for this difference (Kouba 2007).
Besides the topography-related tropospheric delay differences, systematic biases are also observed in VLBI–GNSS tropospheric parameter comparisons. For instance, at Westford (WESTFORD–WES2) a 4–5 mm bias has been reported (Steigenberger et al. 2007; Teke et al. 2011), probably due to the GNSS instrument effect. As ignoring this bias might cause network distortion and potentially degrades the solution, we set up a daily constant tropospheric tie bias parameter \(\Delta x\) as
where \(x_{{{\text{GNSS}}}}\) and \(x_{{{\text{VLBI}}}}\) are tropospheric parameters (residual ZWD and gradients) of GNSS and VLBI, respectively. \(\Delta x\) is constrained to the a priori value:
where \(\sigma\) is the uncertainty and adjusted automatically until the normalized residual is less than 1.96 (Baarda, 1968; Lehmann 2012). Since the topography-related bias has already been accounted for, the variable a priori should be zero in case of no instrument-related effects. However, it is usually not the case in reality and the reason is still under investigation. At each VLBI–GNSS co-location, the average tropospheric parameter difference from the single-technique analysis in each campaign was used as the a priori value. Despite the effort to provide precise a priori tropospheric tie bias determined from single-technique solutions, it is still necessary to allow the tropospheric tie bias to vary a bit instead of fixing to the a priori value in the integrated processing. The reason is that currently the tropospheric parameter agreement between GNSS and VLBI is at the level of 4–6 mm (Teke et al. 2013), and the precision of tropospheric tie bias from single-technique solution is not good enough for the tightly fixed solution. We thus propose the automatic weighting strategy to handle tropospheric tie biases, which can be implemented in the long-term multi-technique integrated processing. In future studies, the best way to handle tropospheric tie bias would be carefully calibrating the values and directly applying the values cautiously in integrated processing.
To investigate the different impact of ZTD and gradient ties, four different setups are performed and shown in Table 3. Note that in solution “TRP” the full set of tropospheric ties, including both ZTD and gradients, are applied. At each co-location, the tropospheric ties are applied at all VLBI–GNSS pairs but not at GNSS–GNSS or VLBI–VLBI pairs to improve the VLBI solution and not over-weight the GNSS solution. In all four solutions GNSS and VLBI observations were processed simultaneously in the common least-squares estimator.
3 Results and discussions
3.1 VLBI station coordinates and network scale
The repeatabilities of station coordinates and network scale indicate the capability to reproduce the terrestrial reference frame using the same network and data processing strategy, and can be used to demonstrate the solution precision and stability. The repeatability is calculated as the weighted standard deviation (WSTD):
where \(X_{{\text{i}}}\) is the estimate at epoch \(i\) of all the n solutions and \(\sigma_{{\text{i}}}\) is the corresponding formal error. The weighted root mean square (WRMS) statistic is further used in Sect. 3.2.
As the tropospheric parameters have a strong correlation with station coordinates, applying tropospheric ties will strengthen the tropospheric parameters and decrease the correlation, and consequently improve the station coordinates, especially in the height component, and subsequently the network scale. The repeatabilities of all station coordinates and the network scale are given in Fig. 2 for each campaign. The network scale is calculated by the seven-parameter Helmert transformation between daily adjusted and a priori coordinates from ITRF2014.
Applying tropospheric ties (solution “TRP”) improves the horizontal components in almost all campaigns. The average repeatability is reduced from 2.6 to 2.3 mm and from 2.4 to 2.1 mm in the north and east components, respectively, that is, 12% improvement compared to the solution without tropospheric ties (solution “NO”). When applying only ZTD or gradient ties improves the repeatability in general, the repeatability is slightly degraded (by 0.1 mm) in a few campaigns, for instance, in CONT17. The horizontal improvement from gradient ties is attributed to the decorrelation between tropospheric gradients and horizontal coordinate components.
Applying tropospheric ties improves the average repeatability of the vertical component over all campaigns by 28% compared to the solution without tropospheric ties, with the value reduced from 7.2 to 5.2 mm, which can be mainly attributed to the ZTD ties, as applying ZTD ties to the precise GNSS estimates alleviates the correlation between the vertical coordinate and ZTD. The repeatability of solutions with only ZTD ties (solution “ZTD”) and that with only gradient ties (solution “GRD”) is 5.1 and 6.7 mm, respectively, corresponding to an improvement of 29 and 6%. Moreover, all campaigns show consistent improvement.
The VLBI network scale is improved by 32% with the repeatability reduced from 0.60 ppb (solution “NO”) to 0.40 ppb (solution “TRP”). The repeatability of solution “ZTD” (0.42 ppb) is better than that of “GRD” (0.53 ppb). Moreover, the solution “ZTD” always has better repeatability in different campaigns, whereas the solution “GRD” ties has worse repeatability in CONT11 (by 0.06 ppb). As the network scale is mainly determined by the station vertical coordinate, the scale improvement is attributed to the ZTD ties.
The station-wise coordinate repeatability differences between solution “NO” without tropospheric ties and solution “TRP” with both ZTD and gradient ties are given in Fig. 3. We can see that most of the VLBI stations have reduced coordinate repeatability values when the tropospheric ties are applied, and as expected the Up component has the largest improvement, which is consistent with the above analysis. In each campaign, a relatively large improvement is usually observed at the VLBI stations with weaker observation geometry. Taking CONT05 as an example, both ALGOPARK and HARTRAO have larger improvement than other stations, and their repeatability values of the solution “NO” are 12.9 and 10.3 mm, respectively, mainly due to the weaker observation geometry: HARTRAO is located in the Southern Hemisphere with around 600 observations per session and ALGOPARK has around 600 observations per session, whereas the rest stations have about 1000–1600 observations per session. The same conclusion applies to other campaigns, such as TIGOCONC in CONT08 (only around 500 observations per session compared to 1000–2400 observations at other stations), ZELENCHK in CONT11 and CONT14 (worse observation quality), and SESHAN25 and YARRA12M in CONT17-VLBA (far from other stations). Among the six networks, the CONT17-VLBA shows the least improvement, with the majority of stations located in North America showing almost no improvement. A few VLBI stations show deteriorated precision up to 1 mm, including the up component of TSUKUBA in CONT08, the north component of TIGOCONC in CONT11, and the east component of FORTLEZA in CONT14. The possible reason is that the observation geometry between co-located GNSS and VLBI stations are different as these VLBI stations are more far away from other stations, and the local weather condition might have rapid fluctuation.
In addition to the repeatability of the station coordinate and network scale, the VLBI baseline length repeatability is also investigated. The baseline length repeatability is not affected by the global parameters such as EOP or the datum constraints, and thus can better indicate the internal precision of the VLBI solution. Figure 4 gives the VLBI baseline length repeatability values of different solutions. Applying tropospheric ties improves the VLBI baseline length repeatability by 1.7 mm on average, and the contribution of ZTD ties is more significant than that of the gradient ties. Moreover, the longer baselines show larger improvement, which is expectable as the major improvement comes from ZTD ties in the up component.
In addition to the significant improvement on the VLBI TRF, the GNSS station coordinates average repeatability is also improved by 2% horizontally and 6% vertically. This relatively small improvement is because GNSS provides better observation geometry with always enough satellites tracked every epoch. The GNSS average repeatability is 1.7, 2.5, and around 4 mm in north, east, and up components, respectively.
3.2 Earth orientation parameters
We evaluate the EOP precision by comparing to the IERS EOP 14 C04 product (Bizouard et al. 2018), and the polar motion and UT1-UTC precision by the day-boundary-discontinuity (DBD, the misclosure at midnight). The IERS EOP 14 C04 is considered to be of high quality as a multi-technique multi-solution combination product (Glaser et al. 2020), whereas the DBD indicates the internal precision. The WSTD of the EOP differences and WRMS of DBD calculated using Eq. 4 are shown in Fig. 5. We can see that applying tropospheric ties improves VLBI EOP estimates in general, as both the agreement to the IERS product and the DBD statistics are improved on all EOP components on average.
The average WSTD values without tropospheric ties are 97 and 78 μas for the x-pole and y-pole offsets, respectively. Applying only ZTD ties reduces the WSTD values by 21% to 77 μas for x-pole and by 11% to 69 μas for y-pole; and the corresponding improvements by applying only gradient ties are 4% (to 93 μas) and 2% (to 76 μas). Applying tropospheric ties (solution “TRP” compared to “NO”) improves the x-pole offset by 18% and the y-pole offset by 13%. The average improvements of PM rates by ZTD ties are 7% for the x-pole rate and 3% for the y-pole rate, and the corresponding improvements by gradient ties are 11 and 14%. Compared to the solution “NO”, the average WSTD values of solution “TRP” are reduced by 12% for x-pole rate and 14% for y-pole rate. The PM DBD is further improved by ZTD ties, and the average improvements by tropospheric ties (solution “TRP” compared to “NO”) are 5 and 10% for the x-pole and y-pole components, respectively. For the PM rates, the contribution of gradient ties is larger than that of ZTD ties.
The impact of applying tropospheric ties (solution “TRP” compared to solution “NO”) on UT1-UTC is not significant (average improvement of 2%), and results of different campaigns are not conclusive. The Length of Day (LoD, the negative first time derivative of dUT1) WSTD is reduced from 17.2 (solution “NO”) to 15.6 μs/day by gradient ties (solution “GRD”), and further to 15.4 μs/day (10% improvement) by additional ZTD ties (solution “TRP”). The UT1-UTC DBD is reduced from 10.5 μs in solution “NO” to 8.7 μs in solution “TRP” (17% improvement), and the major contribution comes from the gradient ties (12% improvement). Both UT1-UTC DBD and LoD statistics are improved by applying tropospheric ties in all CONT campaigns.
The impact of the tropospheric ties on CPO (dX and dY) is diverse in different campaigns. Compared to the solution “NO” without ties, the WSTD values in solution “TRP” are reduced from 48 to 42 μas and from 49 to 47 μas on the dX and dY components, respectively, corresponding to an improvement of 13% and 4%.
The IERS EOP 14 C04 product is not independent as it also uses the data of the CONT campaigns, especially the UT1-UTC and CPO which are more dominated by the VLBI observations of these CONT campaigns (Bizouard et al. 2018). We thus compared the ERP estimates of VLBI solutions to those of the GNSS precise orbit determination (POD) solutions. The GNSS POD solution is performed in the same time period of the CONT campaigns, adopting a similar processing strategy presented in Table 2. However, in the POD solution (1) more than 200 globally distributed IGS stations are processed; (2) the Earth Rotation Parameters (ERP, including polar motion and LoD) are estimated, including offset and rate for polar motion and rate for UT1-UTC, that is, LoD; (3) the dynamic satellite orbits are estimated; and (4) the GNSS ground station coordinates are estimated with the minimum constraints, that is, no-net-rotation and no-net-translation applied on the core stations.
Table 4 presents the average values of the ERP agreement between GNSS and VLBI in CONT05–CONT17, including the improvement of solutions with tropospheric ties compared to the solution without tropospheric ties. The improvements by tropospheric ties are 26, 12, 14, 10, and 5% on the x-pole offset, y-pole offset, x-pole rate, y-pole rate, and LoD, respectively, which are consistent with the improvements when comparing to the IERS EOP 14 C04 product reported earlier. Despite the negative impact of gradient ties on y-pole offset, all other ERP components are improved, especially when both ZTD and gradient ties are applied.
Noticing that the ZTD ties contribute more to the improvement of the PM offsets, whereas the gradient ties contribute more to the PM rates, we further investigated the EOP formal errors, which are presented in Fig. 6. The formal error improvements from ZTD ties on the offsets of x-pole, y-pole, and UT1-UTC are 28, 22, and 15%, respectively, and those on the corresponding rates are 11, 9, and 6%. In comparison, the improvements from gradient ties on the offsets are 21, 19, and 15%, and those on the rates are 17, 17, and 15%. The gradient ties result in larger improvement on the CPO (17%) than the ZTD ties (8–9%). Therefore, the formal errors clearly indicate the different contributions of ZTD and gradient ties on different EOP components.
To better understand the different impacts of ZTD and gradient ties on EOP, Fig. 7 shows the correlation coefficients between the tropospheric parameters and EOP, with and without applying tropospheric ties. We did not consider the tropospheric tie biases in this demonstration because: (1) the correlation coefficient only shows the theoretical situation and is not influenced by the tropospheric tie accuracy, and (2) estimating the tropospheric tie bias introduces correlation between the bias parameter and EOP, which does not exist in the solution without tropospheric ties. Despite the small magnitude of the correlation coefficients, we can see that ERP offsets have a higher correlation with ZTD than gradients, and ERP rates have a higher correlation with gradients (at least one gradient). The CPO (dX and dY) are more correlated with the gradients than with the ZTD. Applying tropospheric ties reduces the correlation, which explains the improvements in EOP formal errors and the agreement to the IERS product. Moreover, we can derive consistent conclusions in the two solutions with different or same temporal resolutions between ZTD and gradients.
Despite the general improvement in most CONT campaigns by applying tropospheric ties, not every campaign shows similar performance. For instance, in CONT17-VLBA the polar motion estimates deteriorate upon applying tropospheric ties (see Fig. 5). This may be caused by assuming the tropospheric tie bias as daily constant, as the different sky coverage between GNSS and VLBI can cause discrepancies. It should be mentioned that the best improvement is usually obtained when both ZTD and gradient ties are applied.
3.3 Tropospheric tie bias
As the a priori tropospheric tie biases from single-technique solutions are used, we further investigate the residual tropospheric tie bias. Figure 8 presents the average values of the residual tropospheric tie bias in CONT11 and CONT14 and the corresponding standard deviation (STD) values. For each co-location, the residual tropospheric tie biases, that is, the tropospheric tie bias estimate minus the a priori value, are averaged over all sessions of the campaign, and the STD value can also be obtained. We can see the residual tropospheric tie biases are usually close to zero with the STD values much larger than the mean values, which is expectable as the a priori bias is derived from the single-technique solution. However, the large STD values indicate that the variation of the bias from session to session cannot be ignored. Moreover, the performance of the same co-location may vary significantly between different campaigns. For instance, the FORTLEZA–BRFT co-location has much larger STD values for both ZTD and gradient tie biases in CONT14 than in CONT11, whereas the HOBART12–HOB2, TSUKUBA23–TSK2, and ZELENCHK–ZECK co-locations all have much larger STD values in CONT11 than in CONT14.
4 Summary and conclusions
We demonstrated the benefits of applying tropospheric ties in the VLBI and GNSS integrated processing on the observation level during CONT05–CONT17. We modeled the topography-related tropospheric tie biases using NWM, and proposed an automatic method to handle the instrument-related systematic biases. Applying VLBI–GNSS tropospheric ties improves the observation geometry, especially for VLBI stations, and thus reduces the correlation between tropospheric parameters and station coordinates, hence yielding a stabilized VLBI network and enhanced EOP estimates.
Compared to the solution without tropospheric ties, applying both ZTD and gradient ties improves the VLBI station coordinate repeatability by 12, 12, and 28% in the north, east, and up components, respectively. The horizontal improvement is mainly from the gradient ties, and the vertical one is mainly from the ZTD ties. The network scale is improved by 32% with the repeatability reduced from 0.60 to 0.40 ppb, mainly due to the ZTD ties.
The VLBI EOP estimates also benefit greatly from tropospheric ties, with the agreements to the IERS EOP product improved by 18, 13, and 2% on x-pole, y-pole, and UT1-UTC components, respectively. The corresponding DBD are improved by 5, 10, and 17%. We demonstrated that the ZTD ties contribute more to the ERP offset improvement, whereas the gradient ties contribute more to the improvement of ERP rates and CPO. This can be illustrated by the correlation coefficients between tropospheric parameters and different EOP components.
Despite the benefits of applying the VLBI–GNSS tropospheric ties, it is worth to mention that the tropospheric parameter agreement between VLBI and GNSS is only about 5 mm for now (Teke et al. 2011, 2013), which may cause slight deterioration in EOP estimates upon applying tropospheric ties. In addition, the tropospheric tie biases that are not related to topography should be further investigated. The VLBI and GNSS combination using additional global ties and local ties (Glaser et al. 2018) was investigated (Wang 2021).
This study is an important step toward the multi-technique integrated processing on the observation level to include all available ties, especially the tropospheric ties for the microwave-based techniques. In further ITRF determination, especially the epoch-specific ITRF (Bloßfeld et al. 2013; Abbondanza et al. 2017), the tropospheric ties can contribute greatly to improve the network stability, especially the scale parameter. The VLBI EOP estimates improved by the tropospheric ties indicate the advantage to apply tropospheric ties in future VLBI processing, especially considering that the VLBI is the only technique capable of determining UT1-UTC and CPO. The enhanced EOP product from IVS can better serve the monitoring of the Earth dynamic system.
Data availability
The GNSS and VLBI observations are available at CDDIS (https://cddis.nasa.gov/Data_and_Derived_Products/CDDIS_Archive_Access.html) (Noll, 2010), the VMF3 data at https://vmf.geo.tuwien.ac.at/, the IERS EOP product at https://www.iers.org/IERS/EN/DataProducts/EarthOrientationData/eop.html.
References
Abbaszadeh M, Clarke PJ, Penna NT (2020) Benefits of combining GPS and GLONASS for measuring ocean tide loading displacement. J Geod. https://doi.org/10.1007/s00190-020-01393-5
Abbondanza C, Chin TM, Gross RS, Heflin MB, Parker JW, Soja BS, van Dam T, Wu X (2017) JTRF2014, the JPL Kalman filter and smoother realization of the International Terrestrial Reference System. J Geophys Res Solid Earth 122:8474–8510. https://doi.org/10.1002/2017jb014360
Altamimi Z, Rebischung P, Métivier L, Collilieux X (2016) ITRF2014: a new release of the International Terrestrial Reference Frame modeling nonlinear station motions. J Geophys Res Solid Earth 121:6109–6131. https://doi.org/10.1002/2016jb013098
Baarda W (1968) A testing procedure for use in geodetic network. Publ Geod 9:2
Behrend D, Thomas C, Gipson J, Himwich E, Le Bail K (2020) On the organization of CONT17. J Geod. https://doi.org/10.1007/s00190-020-01436-x
Bender M, Dick G, Wickert J, Schmidt T, Song S, Gendt G, Ge M, Rothacher M (2008) Validation of GPS slant delays using water vapour radiometers and weather models. Meteorol Z 17:807–812. https://doi.org/10.1127/0941-2948/2008/0341
Bizouard C, Lambert S, Gattano C, Becker O, Richard J-Y (2018) The IERS EOP 14C04 solution for Earth orientation parameters consistent with ITRF 2014. J Geod 93:621–633. https://doi.org/10.1007/s00190-018-1186-3
Bloßfeld M, Seitz M, Angermann D (2013) Non-linear station motions in epoch and multi-year reference frames. J Geod 88:45–63. https://doi.org/10.1007/s00190-013-0668-6
Böhm J, Schuh H (2013) Atmospheric effects in space geodesy. Springer-Verlag, Berlin Heidelberg
Charlot P, Jacobs CS, Gordon D, Lambert S, de Witt A, Böhm J, Fey AL, Heinkelmann R, Skurikhina E, Titov O, Arias EF, Bolotin S, Bourda G, Ma C, Malkin Z, Nothnagel A, Mayer D, MacMillan DS, Nilsson T, Gaume R (2020) The third realization of the International Celestial Reference Frame by very long baseline interferometry. Astron Astrophys 644:A159. https://doi.org/10.1051/0004-6361/202038368
Chen G, Herring TA (1997) Effects of atmospheric azimuthal asymmetry on the analysis of space geodetic data. J Geophys Res Solid Earth 102:20489–20502. https://doi.org/10.1029/97jb01739
Diamantidis P-K, Kłopotek G, Haas R (2021) VLBI and GPS inter- and intra-technique combinations on the observation level for evaluation of TRF and EOP. Earth Planets Space. https://doi.org/10.1186/s40623-021-01389-1
Eriksson D, MacMillan DS, Gipson JM (2014) Tropospheric delay ray tracing applied in VLBI analysis. J Geophys Res Solid Earth 119:9156–9170. https://doi.org/10.1002/2014jb011552
Fernandes MJ, Lázaro C, Ablain M, Pires N (2015) Improved wet path delays for all ESA and reference altimetric missions. Remote Sens Environ 169:50–74. https://doi.org/10.1016/j.rse.2015.07.023
Glaser S, Fritsche M, Sośnica K, Rodríguez-Solano CJ, Wang K, Dach R, Hugentobler U, Rothacher M, Dietrich R (2015) A consistent combination of GNSS and SLR with minimum constraints. J Geod 89:1165–1180. https://doi.org/10.1007/s00190-015-0842-0
Glaser S, König R, Neumayer KH, Nilsson T, Heinkelmann R, Flechtner F, Schuh H (2018) On the impact of local ties on the datum realization of global terrestrial reference frames. J Geod 93:655–667. https://doi.org/10.1007/s00190-018-1189-0
Glaser S, Michalak G, König R, Männel B, Schuh H (2020) Future GNSS infrastructure for improved geodetic reference frames. In: 2020 European navigation conference (ENC), Dresden, Germany, pp 1–10. https://doi.org/10.23919/ENC48637.2020.9317460
Griffiths J (2018) Combined orbits and clocks from IGS second reprocessing. J Geod. https://doi.org/10.1007/s00190-018-1149-8
Heinkelmann R, Willis P, Deng Z, Dick G, Nilsson T, Soja B, Zus F, Wickert J, Schuh H (2016) Multi-technique comparison of atmospheric parameters at the DORIS co-location sites during CONT14. Adv Space Res 58:2758–2773. https://doi.org/10.1016/j.asr.2016.09.023
Hobiger T, Otsubo T (2014) Combination of GPS and VLBI on the observation level during CONT11—common parameters, ties and inter-technique biases. J Geod 88:1017–1028. https://doi.org/10.1007/s00190-014-0740-x
Hobiger T, Shimada S, Shimizu S, Ichikawa R, Koyama Y, Kondo T (2010) Improving GPS positioning estimates during extreme weather situations by the help of fine-mesh numerical weather models. J Atmos Solar Terr Phys 72:262–270. https://doi.org/10.1016/j.jastp.2009.11.018
Hofmeister A, Böhm J (2017) Application of ray-traced tropospheric slant delays to geodetic VLBI analysis. J Geod 91:945–964. https://doi.org/10.1007/s00190-017-1000-7
Huang W, Männel B, Sakic P, Ge M, Schuh H (2020) Integrated processing of ground- and space-based GPS observations: improving GPS satellite orbits observed with sparse ground networks. J Geod. https://doi.org/10.1007/s00190-020-01424-1
Johnston G, Riddell A, Hausler G (2017) The international GNSS service. In: Teunissen PJG, Montenbruck O (eds) Springer handbook of global navigation satellite systems, 1st edn. Springer International Publishing, Cham, Switzerland, pp 967–982. https://doi.org/10.1007/978-3-319-42928-1_33
Kouba J (2007) Implementation and testing of the gridded Vienna Mapping Function 1 (VMF1). J Geod 82:193–205. https://doi.org/10.1007/s00190-007-0170-0
Krügel M, Thaller D, Tesmer V, Rothacher M, Angermann D, Schmid R (2007) Tropospheric parameters: combination studies based on homogeneous VLBI and GPS data. J Geod 81:515–527. https://doi.org/10.1007/s00190-006-0127-8
Kuehn CE, Himwich WE, Clark TA, Ma C (1991) An evaluation of water vapor radiometer data for calibration of the wet path delay in very long baseline interferometry experiments. Radio Sci 26:1381–1391. https://doi.org/10.1029/91rs02020
Landskron D, Böhm J (2017) VMF3/GPT3: refined discrete and empirical troposphere mapping functions. J Geod 92:349–360. https://doi.org/10.1007/s00190-017-1066-2
Landskron D, Böhm J (2018) Refined discrete and empirical horizontal gradients in VLBI analysis. J Geod. https://doi.org/10.1007/s00190-018-1127-1
Lehmann R (2012) Improved critical values for extreme normalized and studentized residuals in Gauss–Markov models. J Geod 86:1137–1146. https://doi.org/10.1007/s00190-012-0569-0
Liu J, Ge M (2003) PANDA software and its preliminary result of positioning and orbit determination. Wuhan Univ J Nat Sci 8:603–609. https://doi.org/10.1007/BF02899825
Liu Y, Ge M, Shi C, Lou Y, Wickert J, Schuh H (2016) Improving integer ambiguity resolution for GLONASS precise orbit determination. J Geod 90:715–726. https://doi.org/10.1007/s00190-016-0904-y
Männel B, Dobslaw H, Dill R, Glaser S, Balidakis K, Thomas M, Schuh H (2019) Correcting surface loading at the observation level: impact on global GNSS and VLBI station networks. J Geod 93:2003–2017. https://doi.org/10.1007/s00190-019-01298-y
Nilsson T, Soja B, Balidakis K, Karbon M, Heinkelmann R, Deng Z, Schuh H (2017a) Improving the modeling of the atmospheric delay in the data analysis of the Intensive VLBI sessions and the impact on the UT1 estimates. J Geod 91:857–866. https://doi.org/10.1007/s00190-016-0985-7
Nilsson T, Soja B, Karbon M, Heinkelmann R, Schuh H (2017b) Water vapor radiometer data in very long baseline interferometry data analysis. In: Freymueller JT, Sánchez L (eds) International symposium on earth and environmental sciences for future generations. International Association of Geodesy Symposia, vol 147. Springer, Cham. https://doi.org/10.1007/1345_2017_264
Noll CE (2010) The crustal dynamics data information system: a resource to support scientific analysis using space geodesy. Adv Space Res 45:1421–1440. https://doi.org/10.1016/j.asr.2010.01.018
Penna NT, Morales Maqueda MA, Martin I, Guo J, Foden PR (2018) Sea surface height measurement using a GNSS wave glider. Geophys Res Lett 45:5609–5616. https://doi.org/10.1029/2018gl077950
Petit G, Luzum B, IERS conventions (2010) (IERS Technical Note No. 36). In: Frankfurt am Main
Pollet A, Coulot D, Bock O, Nahmani S (2014) Comparison of individual and combined zenith tropospheric delay estimations during CONT08 campaign. J Geod 88:1095–1112. https://doi.org/10.1007/s00190-014-0745-5
Rebischung P, Schmid R (2016) IGS14/igs14. atx: a new framework for the IGS products. In: AGU Fall Meeting 2016. https://mediatum.ub.tum.de/doc/1341338/file.pdf
Shamshiri R, Motagh M, Nahavandchi H, Haghshenas Haghighi M, Hoseini M (2020) Improving tropospheric corrections on large-scale Sentinel-1 interferograms using a machine learning approach for integration with GNSS-derived zenith total delay (ZTD). Remote Sens Environ 239:111608. https://doi.org/10.1016/j.rse.2019.111608
Steigenberger P, Tesmer V, Krügel M, Thaller D, Schmid R, Vey S, Rothacher M (2007) Comparisons of homogeneously reprocessed GPS and VLBI long time-series of troposphere zenith delays and gradients. J Geod 81:503–514. https://doi.org/10.1007/s00190-006-0124-y
Teke K, Böhm J, Nilsson T, Schuh H, Steigenberger P, Dach R, Heinkelmann R, Willis P, Haas R, García-Espada S, Hobiger T, Ichikawa R, Shimizu S (2011) Multi-technique comparison of troposphere zenith delays and gradients during CONT08. J Geod 85:395–413. https://doi.org/10.1007/s00190-010-0434-y
Teke K, Nilsson T, Böhm J, Hobiger T, Steigenberger P, García-Espada S, Haas R, Willis P (2013) Troposphere delays from space geodetic techniques, water vapor radiometers, and numerical weather models over a series of continuous VLBI campaigns. J Geod 87:981–1001. https://doi.org/10.1007/s00190-013-0662-z
Teke K, Böhm J, Madzak M, Kwak Y, Steigenberger P (2015) GNSS zenith delays and gradients in the analysis of VLBI Intensive sessions. Adv Space Res 56:1667–1676. https://doi.org/10.1016/j.asr.2015.07.032
Thaller D, Krügel M, Rothacher M, Tesmer V, Schmid R, Angermann D (2006) Combined Earth orientation parameters based on homogeneous and continuous VLBI and GPS data. J Geod 81:529–541. https://doi.org/10.1007/s00190-006-0115-z
Wang J (2021) Integrated Processing of GNSS and VLBI on the observation level. PhD Thesis, Technische Universität Berlin. https://doi.org/10.14279/depositonce-12513
Wang J, Liu Z (2019) Improving GNSS PPP accuracy through WVR PWV augmentation. J Geod 93:1685–1705. https://doi.org/10.1007/s00190-019-01278-2
Wang J, Wu Z, Semmling M, Zus F, Gerland S, Ramatschi M, Ge M, Wickert J, Schuh H (2019) Retrieving precipitable water vapor from shipborne multi-GNSS observations. Geophys Res Lett 46:5000–5008. https://doi.org/10.1029/2019gl082136
Wijaya DD, Böhm J, Karbon M, Kràsnà H, Schuh H (2013) Atmospheric pressure loading. In: Böhm J, Schuh H (eds) Atmospheric effects in space geodesy. Springer, Berlin, Heidelberg, pp 137–157. https://doi.org/10.1007/978-3-642-36932-2_4
Williams S, Bock Y, Fang P (1998) Integrated satellite interferometry: tropospheric noise, GPS estimates and implications for interferometric synthetic aperture radar products. J Geophys Res Solid Earth 103:27051–27067. https://doi.org/10.1029/98jb02794
Wu JT, Wu SC, Hajj GA, Bertiger WI, Lichten SM (1993) Effects of antenna orientation on GPS carrier phase. Manuscripta Geodaet 18:91–98
Wu Z, Liu Y, Liu Y, Wang J, He X, Xu W, Ge M, Schuh H (2020) Validating HY-2A CMR precipitable water vapor using ground-based and shipborne GNSS observations. Atmos Meas Tech 13:4963–4972. https://doi.org/10.5194/amt-13-4963-2020
Zumberge JF, Heflin MB, Jefferson DC, Watkins MM, Webb FH (1997) Precise point positioning for the efficient and robust analysis of GPS data from large networks. J Geophys Res Solid Earth 102:5005–5017. https://doi.org/10.1029/96jb03860
Acknowledgements
We thank the IGS and IVS for providing the GNSS and VLBI observations, the GNSS satellite orbits and clocks, Vienna University of Technology for the tropospheric product. Jungang Wang is financially supported by the Helmholtz – OCPC Postdoc Program (grant no. ZD202121). Kyriakos Balidakis is funded by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) – Project-ID 434617780 – SFB 1464 (TerraQ). The authors would like to thank the editor Jürgen Kusche, the associate editor Zinovy M. Malkin, and three anonymous referees who kindly reviewed this manuscript and provided valuable suggestions and comments.
Funding
Open Access funding enabled and organized by Projekt DEAL.
Author information
Authors and Affiliations
Contributions
MG, KB, SG, RH and HS were involved in writing—review and editing. MG and HS were involved in funding acquisition. MG, RH and HS were involved in supervision. JW, KB and SG were involved in the investigation. JW and MG performed methodology and software. JW contributed to conceptualization, validation and writing—original draft.
Corresponding author
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Wang, J., Ge, M., Glaser, S. et al. Improving VLBI analysis by tropospheric ties in GNSS and VLBI integrated processing. J Geod 96, 32 (2022). https://doi.org/10.1007/s00190-022-01615-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s00190-022-01615-y