Abstract
Nomograms are an easy to use and visually attractive graphical tool to solve for any of the variables within an often complex equation. In seismology, the most well-known nomogram is a three-parallel-scale graphic for the calculation of local magnitude given the epicentral distance and trace amplitude. Until the advent of computers, nomograms were often employed by engineers and scientists in many fields as they provide a means for rapid and accurate calculations as well as helping the user understand the sensitivity of the final results to the input parameters. It is this aid to understanding that remains a key attraction of these graphical tools, which are now rarely seen (although they remain common in some fields of medicine where they are used for rapid screening and estimating risks). In this research letter, we present a nomogram summarising the results of simple probabilistic seismic hazard assessments (PSHAs) for peak ground acceleration and elastic response spectral acceleration for a structural period of 1s and return periods from 100 to 2500 years, where the effects of the activity rate and the slope of the Gutenberg-Richter relation are captured. We believe that this nomogram has considerable educational benefit for engineering seismology students, decision makers and other non-expert users of results of PSHAs.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Nomograms (also called nomographs) are graphical tools that provide the user with an analogue computer to evaluate an often complex equation (or group of connected equations) only by means of a paper copy of the nomogram and a straight edge. In seismology, a commonly seen nomogram is one for the calculation of local magnitude given the epicentral distance and the trace amplitude (Richter 1958), although nomograms for other aspects of seismology have been published, e.g. Mahdyiar (1987) presented a nomogram connecting variables of the Brune (1970, 1971) source spectrum. Until the advent of cheap, easy and ubiquitous computing, nomograms were commonly used in many branches of science and engineering to obtain answers easily, quickly and relatively precisely (e.g. Levens 1959). In the current age of spreadsheets and specialist software, nomograms are no longer commonly used by practicing scientists and engineers. However, they remain a useful educational tool to understand visually the connections among the variables within an equation and the sensitivity of the results to changes in those variables. Nomograms may help those people who prefer pictures to equations understand the inputs and results of complex calculations. This advantage is one reason why nomograms are currently used in medicine when rapidly assessing health risks (e.g. Kattan and Marasco 2010). Another advantage of nomograms is that they cannot be evaluated for combinations of input variables outside the limits of applicability of the equation(s).
In this research letter, we present a nomogram displaying the results of relatively simple probabilistic seismic hazard assessments (PSHAs). In Section 2, the calculations used to construct this nomogram are described and in Section 3 the final nomogram is presented and some example calculations shown using these graphical tools. The results of these calculations are compared to those obtained using the 2013 European Seismic Hazard Model (ESHM13, Woessner et al. (2015)) and the 2014 Earthquake Model of the Middle East (EMME, Giardini et al. (2018)). The article ends with some brief conclusions. The nomogram presented here should not be seen as a replacement for a real PSHA but only as an educational tool.
2 Method for the construction of the nomogram
The aim of any PSHA is to estimate the probabilities of exceeding, within a fixed observational time (e.g. 50 years), different ground-motion levels at a site of interest. The exceedance probabilities of the ground-motion levels are controlled by both the ground-motion model and the forecasts of earthquakes of different magnitudes at various locations (as described by a seismogenic source model).
2.1 Simple probabilistic seismic hazard assessments
To generate our nomogram, we combine the ground-motion model of the ESHM13 (Delavaud et al. 2012) and an area source zone of 2∘× 2∘ (surface area of 49,560 km2) and calculate the seismic hazard at the centre of this zone. A time-independent model of seismic activity rates is assumed and defined by an exponential magnitude distribution (Gutenberg and Richter 1944): \(\log _{10} N(M)=a-bM\), where N(M) is the cumulative number of earthquakes per unit time equal to or larger than magnitude M, and a and b are empirical constants. The activity rate (a value) represents the total seismic productivity of a given source (\(=\log _{10} N(M=0)\), i.e. log of the number of earthquakes with M > 0), and the b value is the negative slope of the recurrence curve expressing average ratio of exponentially distributed small and large earthquakes. This parameter controls the occurrence rates of moderate to large earthquakes. For this nomogram, the range of activity rates is selected to be representative of low to high seismicity areas in the ESHM13 (Woessner et al. 2015). We consider three b values: 0.75, 1.00 and 1.25, to capture the variability in this parameter within ESHM13. An upper bound magnitude of 8.5 has been imposed. The seismicity is concentrated at a depth of 5km so the nomogram is only for shallow crustal seismicity. The annual cumulative rates of (M > M0) considered are 0.05, 0.1, 0.2, 0.3, 0.5, 0.75, 1.0, 1.5 and 2.0 for M0 = 4.5. Hence, the nomogram should not be used outside the range N(M0 = 4.5) = 0.05 to 2.0.
Two ground-motion intensity measures (IMs) are considered: peak ground acceleration (PGA) and pseudo-spectral acceleration for a structural period of 1s and 5% of critical damping [SA(1s)]. We consider five mean return periods: 100, 200, 475, 1000, 2500 years, roughly corresponding to the requirements of modern seismic design codes (e.g. Eurocode 8 (Comité Européen de Normalisation 2005)). Hence, the nomogram should not be used outside the range of return periods 100 to 2500 years. The calculations were performed in OpenQuake (Pagani et al. 2014) using extended ruptures.
2.2 Fitting the assessed seismic hazard with closed-form equations
The results from each of the calculations (where each calculation consists of the same input except for the activity rate) were fit using a power law connecting the PGA or SA(1s) to the return period. The equation (in terms of natural logarithms to make the relation linear) fit was
where y is PGA or SA(1s) in cm/s2, T is the return period in years, and c0 and c1 are coefficients found by linear least squares regression. The match between the calculated expected PGAs and SA(1s) and the predictions using these equations is very close for all cases (Figs. 1 and 2). Power laws modelling the annual frequencies of exceedance of different levels of ground-motion intensity are commonly used to parameterise hazard curves (e.g. Comité Européen de Normalisation 2005; Lubkowski 2010; Kennedy2011).
Next, for both PGA and SA(1s), cubic equations are found to predict perfectly (coefficient of determination R2 = 100%) the values of c0 and c1 given \(\ln N(M_{0}=4.5)\) for each value of b (Figs. 3 and 4). The Electronic Supplement is an Excel spreadsheet to evaluate Eq. 1.
3 The nomogram
The open-source program pynomoFootnote 1 was then used to draw a type 10 nomogram after putting Eq. 1 into the form required for this type, i.e.
where \(F_{1}(u)=\ln y\), \(F_{2}(v)=-\ln T\), F3(w) = c1(N) and F4(w) = −c0(N). The resulting nomogram is shown in Fig. 5. To read Fig. 5, connect two of the variables (e.g. N(M0 = 4.5) and return period) with a straight line and where it crosses the axis for the third variable that is its value (e.g. PGA). Example calculations are shown using red lines for a return period of 475 years and an activity rate of N(M0 = 4.5) = 0.1 (a moderate seismicity zone).
Needless to say that the comparison between estimates from the simplified nomogram and those from a real PSHA (e.g. ESHM13) is challenging for two main reasons. Firstly, the latter is a full hazard calculation that blends full distributions of the inputs, in particular the alternative ground-motion and seismogenic source models. Secondly, the hazard calculation with OpenQuake uses extensive ruptures for large magnitudes, which when combined with permissible boundaries of seismic sources can result in a more complex hazard pattern than the estimates from a single seismic source. In the analysis, we have considered a single seismogenic source and the ground-motion models for two seismo-tectonic domains: the active shallow crust and stable continental region as described in Delavaud et al. (2012). Hence, the contributions of the two ground-motion models are reflected in the hazard results.
The expected PGAs and SA(1s) for sites covered by ESHM13 are obtained for the five return periods from the European Facilities of Earthquake Hazard and Risk (EFEHR).Footnote 2 These hazard estimates are then grouped by the seismic activity parameters (the a and b values discussed in Section 2.1) for the source zone enclosing the selected site. The activity rates were normalised to the surface area of the 2∘× 2∘ area considered for the simple PSHA. It was found that the expected PGAs and SA(1s) estimated using the nomogram were generally within 50% of those from ESHM13 for locations with the same normalised activity rates. We also conducted a comparison for locations covered by EMME and a similarly close match was found. Therefore, we have chosen to indicate on Fig. 5 the rough limits of the nomogram to provide accurate hazard estimates (as measured by the match to results from ESHM13 and EMME for many locations) by giving a range of ± 50% around the exact PGAs and SA(1s) obtained from the simple PSHAs. For example, the simple PSHA for a return period of 475 years, N(M0 = 4.5) = 0.1 and b = 1.00 gives a exact PGA value of 67cm/s2 but rather than indicate this on the central nomogram axis the range from 34 to 101cm/s2 (i.e. ± 50% of this exact value) is shown instead.
To compare estimates from the nomogram to those from real PSHAs, hazard results from ESHM13 for some example locations (14 European capitals) are listed in Table 1 alongside estimates obtained from the nomogram, assuming b = 1.00 (often a valid assumption (e.g. Frohlich and Davis 1993)). To obtain N(M0 = 4.5) for each of the considered locations, the instrumental earthquake catalogue used for the ESHM13 (SHEEC 1900-2006, (Grünthal et al. 2013)) was queried for a 2∘× 2∘ box centred on the location to obtain the average number of earthquakes with Mw ≥ 4.5 per year.
This comparison shows that for eight of the considered cities (Athens, Bern, Bratislava, Lisbon, Ljubljana, Reykjavik, Podgorica and Zagreb) hazard levels from the nomogram are generally within 50% of those from the real PSHA of ESHM13. Such a convergence among results from the simple PSHAs (represented by the nomogram on Fig. 5) and this regional PSHA was found despite differences between the ground-motion models used in ESHM13 and the complexities of its seismogenic source models. Although it could be surprising that the simple PSHA used to derive the nomogram can provide rough estimates of the results from a real PSHA, it can be partially explained by the observation that hazard disaggregation (Bazzurro and Cornell 1999) often shows that the most important earthquakes are within 100km (or even closer) from the location of interest (e.g. Barani et al. 2009). Therefore, the assumption that the location is within a single local source zone of uniform seismicity can often be made.
Table 1, however, does demonstrate the limitations of the nomogram. When the average annual number of earthquakes with Mw ≥ 4.5 is less than 0.05 (e.g. Brussels) or greater than 2.0 (e.g. Tirana), the nomogram cannot be used (because of the lower limit other capital cities in the north of Europe, e.g. London and Oslo, where the seismicity is low are not included in this table). When the seismic hazard is dominated by distant earthquakes (e.g. Bucharest, for which the Vrancea earthquake zone is important), the nomogram significantly underestimates the results of the real PSHA. In contrast, if the location is close to but not within an area of high seismicity (e.g. Belgrade, Rome and Sarajevo), the nomogram can overestimate the results from a real PSHA. It should also be noted that if the local seismicity means that b does not equal unity then the difference between the nomogram and the results of a real PSHA could be large.
4 Conclusions
In this short research letter, we have presented a nomogram (Fig. 5) to capture the results of a series of simple probabilistic seismic hazard assessments (PSHAs) for return periods between 100 and 2500 years and peak ground acceleration and pseudo-spectral acceleration for a structural period of 1s and 5% of critical damping. The characteristics of the seismicity modelled are the annual average number of earthquakes of Mw ≥ 4.5 within a 2∘× 2∘ square centred on the site of interest and the slope of the Gutenberg-Richter earthquake recurrence relation. The purpose of this nomogram is not to replace real PSHAs but to give the user a graphical understanding of the influence of the different inputs to PSHAs. For example, the nomogram shows the relatively minor influence of the b value on peak ground acceleration but a large influence for long-period spectral accelerations. It also shows that the expected ground motions for a given return period increase as the activity rate increases but that the rate of increase reduces. In conclusion, we contend that this nomogram provides the non-expert with valuable insights into PSHAs that is not possible with standard means of presentation.
References
Barani S, Spallarossa D, Bazzurro P (2009) Disaggregation of probabilistic ground-motion hazard in Italy. Bulletin of the Seismological Society of America 99(5):2638–2661. https://doi.org/10.1785/0120080348
Bazzurro P, Cornell CA (1999) Disaggregation of seismic hazard. Bulletin of the Seismological Society of America 89(2):501–520
Brune JN (1970) Tectonic stress and the spectra of seismic shear waves from earthquakes. J Geophys Res 75(26):4997–5009
Brune JN (1971) Correction. J Geophys Res 76(20):5002
Comité Européen de Normalisation (2005) Eurocode 8, Design of structures for earthquake resistance — Part 1: General rules, seismic actions and rules for buildings. European Standard NF EN 1998–1
Delavaud E, Cotton F, Akkar S, Scherbaum F, Danciu L, Beauval C, Drouet S, Douglas J, Basili R, Sandikkaya MA, Segou M, Faccioli E, Theodoulidis N (2012) Toward a ground-motion logic tree for probabilistic seismic hazard assessments in Europe. J Seismology 16 (3):451–473. https://doi.org/10.1007/s10950-012-9281-z
Frohlich C, Davis SD (1993) Teleseismic b values; Or, much ado about 1.0. J Geophys Res 98 (B1):631–644
Giardini D, Danciu L, Erdik M, Şeşetyan K, Demircioğlu Tümsa MB, Akkar S, Gülen L, Zare M (2018) Seismic hazard map of the Middle East. Bulletin of Earthquake Engineering 16(8):3567–3570. https://doi.org/10.1007/s10518-018-0347-3
Grünthal G, Wahlström R, Stromeyer D (2013) The SHARE European Earthquake Catalogue (SHEEC) for the time period 1900–2006 and its comparison to European-Mediterranean Earthquake Catalogue (EMEC). J Seismology 17(4):1339–1344. https://doi.org/10.1007/s10950-013-9379-y
Gutenberg R, Richter CF (1944) Frequency of earthquakes in California. Bulletin of the Seismological Society of America 34(4):185–188
Kattan MW, Marasco J (2010) What is a real nomogram? Seminars in Oncology 37(1):23–26. https://doi.org/10.1053/j.seminoncol.2009.12.003
Kennedy RP (2011) Performance-goal based (risk informed) approach for establishing the SSE site specific response spectrum for future nuclear power plants. Nuclear Engineering and Design 241:648–656. https://doi.org/10.1016/j.nucengdes.2010.08.001
Levens AS (1959) Nomography, 2nd edn. Wiley, New York
Lubkowski ZA (2010) Deriving the seismic action for alternative return periods according to Eurocode 8. In: Proceedings of the 14th European conference on earthquake engineering
Mahdyiar M (1987) A nomograph to calculate source radius and stress drop from corner frequency, shear velocity, and seismic moment. Bulletin of the Seismological Society of America 77(1):264–265
Pagani M, Monelli D, Weatherill G, Danciu L, Crowley H, Silva V, Henshaw P, Butler L, Nastasi M, Panzeri L, Simionato M, Viganò D (2014) OpenQuake Engine: an open hazard (and risk) software for the Global Earthquake Model. Seismological Res Lett 85(3):692–702. https://doi.org/10.1785/0220130087
Richter CF (1958) Elementary seismology. Freeman and Co., San Francisco
Woessner J, Danciu L, Giardini D, Crowley H, Cotton F, Grünthal G, Valensise G, Arvidsson R, Basili R, Demircioglu MB, Hiemer S, Meletti C, Musson RW, Rovida AN, Sesetyan K, Stucchi M, The SHARE Consortium (2015) The 2013 European seismic hazard model: key components and results. Bulletin of Earthquake Engineering 13(12):3553–3596. https://doi.org/10.1007/s10518-015-9795-1
Acknowledgements
We thank Leif Roschier, the author of pynomo, the program used to generate the nomograms shown here, and Ron Doerfler for his website deadreckonings.com with much useful information on nomograms. John Douglas thanks his colleagues Neil Ferguson and Mike Kenny for the lunchtime discussion that inspired him to investigate the advantages of nomograms. Finally, we thank two reviewers for their careful reviews of earlier versions of this manuscript.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Douglas, J., Danciu, L. Nomogram to help explain probabilistic seismic hazard. J Seismol 24, 221–228 (2020). https://doi.org/10.1007/s10950-019-09885-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10950-019-09885-4