Abstract
The Cr (VI) and Ni (II) ion biosorption process by natural sugarcane bagasse in a fixed bed column was investigated. The characteristic removal parameters such as retention capacity, removal percent and unused bed length were experimentally determined at different operating conditions. Overall mass transfer coefficient was investigated and reported for the studied biosorption system. The breakthrough curves were simulated using Matlab2010a software to check the validity of the obtained overall mass transfer coefficients. Experimental data fitted well with predicted data (R2 = 0.94). A statistical analysis was performed using the software Statgraphics Centurion-X V15.2.06 to compare the simulated and experimental data. No significant differences were observed between experimental and simulated data. The best operating conditions for Cr (VI) removal were 15 mg/L of inlet concentration and 1.5 g of biosorbent. For Ni (II) removal the best results were obtained with 25 mg/L of inlet concentration and 1.5 g of solid. The results obtained through the breakthrough curve showed high removal percentages (94.70 and 97.90% for chromium and nickel, respectively). Moreover, results indicated that sorption of these metals was irreversible and it was controlled by the mass transfer at the external film.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Nowadays, pollution of wastewaters by heavy metals caused by anthropogenic activities is a problem to be solved (Martín-Lara et al. 2017). Chromium and nickel are heavy metals that are considered as very dangerous pollutants in wastewaters because they are persistent as they do not degrade to harmless compounds. They are toxic substances known to cause multiple organ damage, even at low concentrations. Moreover, they are human carcinogens and they cause long-term health problems in human population (Iqbal 2016; Tchounwou et al. 2012).
Different technologies have been tested for heavy metal removal from wastewater such as chemical precipitation, ion exchange, reverse osmosis, electro-flotation and bioremediation among others. These methodologies present some drawbacks like the production of toxic sludge, high energy and chemical requirements and low efficiency (Mushtaq et al. 2016; Rashid et al. 2016).
Biosorption is an interesting alternative for metal removal which overcomes the disadvantages of the aforementioned methods. It is low cost and it has a high efficiency and selectivity for particular contaminants. Moreover, the use of chemicals is minimum and no sludge is generated. Furthermore, regeneration of the biosorbents and metal recovery are possible (Bhatti et al. 2016). Many agricultural and forestry waste materials have been tested for biosorption such as rice husk, pine bark, sawdust, peanut and orange peels among others (Nadeem et al. 2016; Tahir et al. 2017).
Use of adsorption systems for industrial and municipal wastewater treatment has become more prevalent during the recent years (Babu and Gupta 2004). An adsorption process is often used at the end of a treatment sequence for pollution control as high degree of purification can be achieved. Adsorption is an important step in industrial downstream processing. It is important to stop the adsorption stage before the adsorbent is saturated which requires a thorough understanding of adsorption characteristics (Bautista et al. 2003). At industrial scale, the breakthrough time of the operation must be determined through an economic and, eventually, environmental evaluation of the process.
The adsorption kinetics can be described by various models depending upon the mechanism of transport (pore diffusion, solid diffusion, and both mechanisms in parallel) assumed inside the particles or in the external film (Bajpai et al. 2004, 2007; Dizge et al. 2009; Gupta and Babu 2009; Plazinski and Rudzinski 2010).
In the present study, the effect of various operating variables (bed height and inlet adsorbate concentration) on the process of fixed-bed biosorption was studied. Furthermore, the adsorption kinetics were studied through a mathematical model that takes into account both the external and internal mass transfer resistances, nonideal plug flow along the column, and the variation of fluid velocity along the column.
Tan and Spinner (1994), developed a more complete model for ionic exchange that includes the limitation of total transference. This model can predict the breakthrough curves for any species removed by the biosorbent and elution curves obtained during regeneration. However, the solution of the model is extremely complex and the values of the mass transfer coefficients for all ionic species present in the system is required.
The values of these coefficients can be estimated or determined by fitting the model to experimental data (Yang and Volesky 1996; Hatzikioseyian et al. 2001; Borba et al. 2006; Escudero et al. 2013; Gu et al. 2013; Sulaymon et al. 2014). The main advantage of the model is that it can simulate and predict the performance of a column under various conditions including different flow rates, feed compositions, column size, bed porosities and ionic forms of the biosorbent.
Materials and methods
Biosorbent
Sugar cane bagasse samples were collected from the Sugar Power Station located in the Central University “Marta Abreu” of Las Villas, in Santa Clara, Cuba. The bagasse was sieved in a sieve machine Model MLW with a group of sieves (Tyler Series). The fraction between 0.5 and 1 mm was selected.
Preparation of standards and reagents
Preparations of Cr (VI) and Ni (II) solutions was carried out using analytical grade reagents. Potassium dichromate (K2Cr2O7) and nickel sulfate (II) hexahydrate (NiSO4·6H2O) ACS 99% supplied by J. T. Baker were used for preparing the synthetic wastewater.
Solutions were prepared by diluting the analytical reagents with distilled water to desired concentrations. The solutions of nickel were prepared at concentrations of 15 and 25 mg/L. Chromium solutions were prepared at a concentration of 10 and 15 mg/L.
The pH of the solution is a key parameter for the evaluation of biosorption performance, specifically in the metal speciation (Guzman et al. 2003). In the case of heavy metals, biosorption studied in this work, the speciation of the metals is not changed with the pH (constant in the process), therefore, the main effect will be explained by the impact of this parameter on the functional groups of the biomass. It was studied that the most reactive groups (carboxylic groups) on the biomass are generally found under charge point zero (pH 6). (Vicente 2011; Bermúdez et al. 2011).
Castro et al. 2004, reported that the pKa of carboxylic groups on alginate fraction in the biomass is generally found between 2 and 4.
Then, the pH of the solution was adjusted by adding the appropriate quantity of 0.1 M hydrochloric acid (HCl). The initial pH of solutions was fixed at 2 and 5 for dichromate solutions and nickel sulfate, respectively.
Hydraulic tests and selection of the operation parameters
The column (diameter: 1 cm, height: 20 cm) was filled with natural sugar cane bagasse and water was circulated with the purpose of determining the most appropriate flows for the established operation conditions.
Ko et al. (2001) suggested for the processes on the macroscopic level, that if the flow rate increases, the residence time of the fluid in the bed decreases, resulting in a low use of the biosorption capacity of the bed. On the other hand, for the processes on the microscopic level, the change of the volumetric flow rate affects only the diffusion of the ions in the liquid film, but not the one in the bioadsorbent. According to this author, high volumetric flow rates result in small resistances in the liquid film and high values of the external mass transfer coefficient. Based on these considerations, the best flow allows a non-fragmenting stable bed and no draining occurrence at the end of the operation. Besides, an appropriate flow gives a proper drop pressure. As a result, the selected feed flow was of 2 mL/min. The selected bed height was six times the internal diameter of the column (Khalid et al. 1998; Treybal 1993).
Once studied, the biosorption of Cr (VI) and Ni (II) using one fixed bed column, several models were applied to the experimental data of the breakthrough curves for carrying out the fitting and the determination of the mass transfer parameters. The samples were collected every 5 min for the first 100 min and then each 10 min, until the biosorbent was saturated.
The chromium and nickel concentrations were determined by atomic absorption spectrophotometry using Pye Unicam SP9 PHILIPS Atomic Absorption Spectrophotometer, Chromium Analytical Line: 357.9 nm and Nickel Analytical Line: 232.0 nm to calculate the metal removal percent in a column.
Data analysis
To analyze the dynamic Cr (VI) and Ni (II) removal in up-flow fixed bed column, breakthrough curves were drawn and the data were evaluated with the following equations.
-
Effluent volume, Vef (mL), can be calculated using Eq. (1):
$$ V_{\text{ef}} \,{ = }\,F *t_{\text{b}} $$(1)where F is the volumetric flow rate circulating through the column expressed in mL/min and tb represents the total flow time in min.
-
Total amount of metal which entered in the column, mtotal in mg, can be calculated as follows:
$$ m_{\text{total}} = \frac{{C_{\text{o}} \, \times \,F\, \times \,t_{\text{b}} }}{ 1 0 0 0} $$(2)where Co represents the metal inlet concentration in mL/min.
-
Total amount or metal retained by the column, mads in mg, is represented by the area under the breakthrough curve. It can be calculated by the following expression:
$$ m_{\text{ads}} = \frac{F}{ 1 0 0 0}\mathop \int \limits_{{t{ = 0}}}^{{t{ = }t_{\text{b}} }} C_{\text{R}} {\text{dt}} $$(3)where CR denoted the concentration of metal removal in mg/L.
Estimation of mass transfer parameters
The concentration in the fluid and the solid phase change with time as well as with position in a fixed bed. The transfer process is described by the overall volumetric mass transfer coefficient (Kca) obtained from a solute material balance in the column considering irreversible isotherms (McCabe et al. 1993).
N is defined as:
The parameter τ is defined as:
where \( H\frac{\varepsilon }{{u_{\text{o}} }} \) is the time to displace fluid from the bed voids (normally negligible); uoCot is the total solute fed to a unit cross-section of bed up to time t; and \( \rho_{\text{s}} \left( {1 - \varepsilon } \right)HW_{\text{sat}} \) is the capacity of the bed, or the amount of the solute exchanged if the entire bed came to equilibrium with the feed.
The solid line in Fig. 1 represents the predicted breakthrough curve (McCabe et al. 1993). The slope increased with time and C/Co becomes 1 for N(τ−1) = 1.
If the diffusion in the pores control the rate of adsorption, the breakthrough curve has an opposed form to that of the corresponding to the control of the external film. The breakthrough curve is S-shaped when both internal and external resistance are significant, as shown in dashed line.
Calculation of the unused bed surface
Calculation of the unused bed surface is a method to evaluate the adsorption capacity of biosorbents in continuous flow-packed columns.
Hence, for a full bed length (H), the length of unused bed (HUNB) is:
where ts represents the saturation time of the biosorbent in min. Small values of this parameter mean that the breakthrough curve is close to an ideal step with negligible mass-transfer resistance. Then, minimum HUNB quantities are desirable in optimized operational conditions.
It is important to set the breakthrough point considering the concentration according to the limit fixed by environmental standards that sets discharge concentration limits for heavy metal ions, or other process conditions.
Breakthrough curve simulation
Simulation is a modern technique that uses mathematical models to predict the behavior of a system.
To predict the breakthrough point in biosorption systems, Eq. (8) can be applied (McCabe et al. 1993).
The longitude of saturated bed (Hsat) it is the product of the speed of the mass transfer section for the time since the area begins to move and it can be calculated using Eq. (9)
And Wsat, which is adsorbate amount in equilibrium with the fluid (mg/g) can be calculated as:
To check the validity of the obtained results, the Kca values determined from the experimental data were used to simulate the breakthrough curves using Matlab2010a software. Simulations were limited to C/Co ≈ 0.5, as the considered margin is enough to contain the breakthrough point under all the experimental conditions. The disposal limits of Ni (II) and Cr (VI) according to Cuban Norm NC 27-12 are 2.0 and 0.5 mg/L, respectively.
Statistical analysis of the data
A statistical analysis was performed using the software Statgraphics Centurion-X V15.2.06 to compare the simulated and experimental data. R squared coefficient, standard deviation and F tests were calculated to determine the reliability of the data calculated by mathematical models compared to experimental data.
Results and discussion
The breakthrough curves for adsorption of Cr (VI) and Ni (II) were determined experimentally in a packed column with sugarcane bagasse. All the experiments were performed at 25 °C.
Figure 2 shows the plot of the mean data from three experiments for each operation conditions.
Table 1 shows characteristic parameters of the removal of Cr (VI) and Ni (II). It is observed that the best operating conditions for the removal of Cr (VI) are Co = 15 mg/L and m = 1.5 g, while for the Ni (II) are Co = 25 mg/L and m = 1.5 g, with a removal percentage of 94.70 and 97.90%, respectively. The maximum retention capacities of natural sugarcane bagasse were similar to that reported by Karna (2013). However, Mishra et al. (2016), who studied biosorption process of Ni and Cr with Hydrilla verticillata, found a higher removal percentage for chromium than for nickel (96 and 92%, respectively) which is in contrast with the obtained results.
Sharma and Singh (2013) observed that the percentage Ni absorbed by rice straw increased with increasing inlet concentration, which is in accordance with the results found in this work. They found that a higher adsorbate concentration gave a higher driving force for biosorption process.
On the other hand, Manikandan et al. (2016) studied Cr (VI) adsoption by waste litchi peels. They found that when inlet concentration increased, the breakthrough time decreased which is in accordance with the results obtained in this work.
The mass transfer parameters were estimated from the breakthrough data of Cr (VI) and Ni (II) in solutions and are enlisted in Table 2. It is observed that the Cr (VI) and Ni (II) increase significantly the parameters with increasing initial concentration of the solution, indicating that the biosorption process was fast and very favorable.
This process was considered as irreversible adsorption because the mass transfer rate was proportional to the initial concentration of the fluid. As a result, it could be concluded that initial metal concentration influenced significantly the driving force that governs all process of mass transfer.
In the biosorption of Cr (VI), the height of unused bed (HUNB) varied with operating conditions in the column. However, this behavior is less marked in the removal of Ni (II).
The plot of N(τ−1) versus C/Co for the biosorption of Cr (VI) and Ni (II) on natural sugar cane bagasse showed that the rate-controlling step of the process was the external film, which proved that the biosorption of these metals were irreversible. Figure 3 shows the behavior described above and explained in Sect. “Calculation of the unused bed surface” corresponding to different operation conditions.
Figure 4 shows the simulated curves using the model that include the calculated values of Kca.
A statistical analysis was carried out using the software Statgraphics Centurion-X V15.2.06 to check the reliability of the results obtained in the simulation compared to the experimental ones. Table 3 shows the obtained results.
It is clear that the breakthrough curves presented good agreement with the experimental data (R2 is always above 0.94). In addition, the F tests demonstrated that in all the cases there was no significant difference between the simulated data and the experimental data because the significance level was always bigger than 0.05.
Other authors like Chao et al. (2014) and Chen et al. (2012) applied other mathematical models like Thomas model and Yoon–Nelson models, obtaining good agreement between experimental and predicted results (R2 values above 0.90). In future works, different models could be applied to experimental data obtained for sugarcane bagasse to determine which of the models give the best fitting.
Conclusions
It can be concluded that the use of sugarcane bagasse for Cr (VI) and Ni (II) removal from wastewater is suitable as the metal retention values obtained in this work were high. Hence, it can be considered as a low-cost and efficient alternative for the removal of those metals. Results showed that metal retention was higher when inlet metal concentrations were 15 and 25 mg/L for chromium and nickel, respectively.
Values of mass transfer coefficients were reported for the removal of Cr (VI) and Ni (II) with sugarcane bagasse as biosorbent. Through the estimation of the mass transfer parameters, it was possible to establish that the biosorption of Cr (VI) and Ni (II) by sugarcane bagasse was fast and irreversible. The controlling stage was mainly governed by the resistance in the external film. The Kca values determined from the experimental data were used to simulate the breakthrough curves. The statistical analysis of experimental and theoretical data showed no significant differences between both data.
Future work will focus on the study of the use of sugarcane bagasse for the removal from wastewater of other heavy metals or other kind of contaminants such as emergent pollutants.
Abbreviations
- V ef :
-
Effective volume (ml)
- F :
-
Volumetric flow (mL/min)
- t :
-
Time (min)
- t b :
-
Break-point time (min)
- t s :
-
Saturated point time (min)
- C o :
-
Initial concentration (mg/L)
- C :
-
Concentration in the time to the exit of the column (mg/L)
- C R :
-
Concentration of retained metal (mg/L)
- m total :
-
Total amount of heavy metal sent to column (g)
- m ads :
-
Total amount of heavy metal retained in column (g)
- m o :
-
Total mass of the adsorbate (g)
- u o :
-
Superficial velocity of fluid (cm/min)
- H :
-
Bed length (cm)
- H UNB :
-
Length of unused bed (cm)
- H sat :
-
Longitude of saturated bed (cm)
- N :
-
Overall number of transfer units
- W sat :
-
Adsorbate amount in equilibrium with the fluid (mg/g)
- K ca :
-
Overall volumetric mass transfer coefficient (min−1)
- τ :
-
Dimensionless time
- ε :
-
Bed porosity
- ρ s :
-
Bulk density (g/L)
- ρ p :
-
Particle density (g/L)
References
Babu BV, Gupta S (2004) Modeling and Simulation for Dynamics of Packed Bed Adsorption. In: Proceedings of International Symposium and 57th Annual Session of IIChE in association with AIChE (CHEMCON-2004), Mumbai
Bajpai J, Shrivastava R, Bajpai AK (2004) Dynamic and equilibrium studies on adsorption of Cr (VI) ions onto binary bio-polymeric beads of cross linked alginate and gelatin. Colloid Surf A 236:81–90
Bajpai J, Shrivastava R, Bajpai AK (2007) Binary biopolymeric beads of alginate and gelatin as potential adsorbent for removal of toxic Ni2+ ions: a dynamic and equilibrium study. J Appl Polym Sci 103:2581–2590
Bautista L, Martinez M, Aracil J (2003) Adsorption of ALPHA-amylase in a fixed bed: operating efficiency and kinetic modeling. AIChE J 49:2631–2641
Bermúdez YG, Rico ILR, Bermúdez OG, Guibal E (2011) Nickel biosorption using Gracilaria caudata and Sargassum muticum. Chem Eng J 166:122–131
Bhatti HN, Zaman Q, Kausar A, Noreen S, Iqbal M (2016) Efficient remedation of Zr (IV) using citrus peel waste biomass: kinetic, equilibrium and thermodynamic studies. Ecol Eng 95:216–228
Borba CE, Guirardello R, Silva EA, Veit MT, Tavares CRG (2006) Removal of Ni (II) ions from aqueous solution by biosorption in a fixed bed column: experimental and theoretical breakthrough curves. Biochem Eng J 30:184–191
Castro C, Herrero R, Vicente MES (2004) Gibbs–Donnan and specific-ion interaction theory descriptions of the effect of ionic strength on proton dissociation of alginic acid. J Electroanal Chem 564:223–230
Chao H-P, Chang C-C, Nieva A (2014) Biosorption of heavy metals on Citrus maxima peel, passion fruit shell, and sugarcane bagasse in a fixed-bed column. J Ind Eng Chem 20:3408–3414
Chen S, Yue Q, Gao B, Li Q, Xu X, Fu K (2012) Adsorption of hexavalent chromium from aqueous solution by modified corn stalk: a fixed-bed column study. Bioresour Technol 113:114–120
Dizge N, Keskinler B, Barlas H (2009) Sorption of Ni(II) ions from aqueous solution by Lewatit cation-exchange resin. J Hazard Mater 167:915–926
Escudero C, Poch J, Villaescusa I (2013) Modelling of breakthrough curves of single and binary mixtures of Cu (II), Cd (II), Ni (II) and Pb (II) sorption onto grape stalks waste. Chem Eng J 217:129–138
Gu T, Iyer G, Cheng KSC (2013) Parameter estimation and rate model simulation of partial breakthrough of bovine serum albumin on a column packed with large Q Sepharose anion-exchange particles. Sep Purif Technol 116:319–326
Gupta S, Babu BV (2009) Modeling, simulation, and experimental validation for continuous Cr (VI) removal from aqueous solutions using sawdust as an adsorbent. Bioresour Technol 100:5633–5640
Guzman J, Saucedo I, Revilla J, Navarro R, Guibal E (2003) Copper sorption by chitosan in the presence of citrate ions: influence of metal speciation on sorption mechanism and uptake capacities. Int J Biol Macromol 33:57–65
Hatzikioseyian A, Tsezos M, Mavituna F (2001) Application of simplified rapid equilibrium models in simulating experimental breakthrough curves from fixed bed biosorption reactors. Hydrometallurgy 59:395–406
Iqbal M (2016) Vicia faba bioassay for environmental toxicity monitoring: a review. Chemosphere 144:785–802
Karna NK (2013) Modelación matemática del proceso de biosorción de Cr+6 y Ni+2: estudios en serie en columnas de lecho fijo con Bagazo de Caña de Azúcar. Trabajo de Diploma, Universidad Central “Marta Abreu “de Las Villas, Santa Clara
Khalid NRA, Ahmad S, Kiani SN, Ahmed J (1998) Adsorption of cadmium from aqueous solutions on rice husk. Radiochim Acta 83:157–162
Ko DCK, Poter JF, Mckay G (2001) Film-pore diffusion model for the fixed bed sorption of copper and cadmium onto bone char. Water Res 36:3786–3886
Manikandan NA, Alemu AK, Goswami L, Pakshirajan K, Pugazhenthi G (2016) Waste litchi peels for Cr (VI) removal from synthetic wastewater in batch and continuous systems: sorben characterization, regeneration and reuse study. J Environ Eng 142(9):C4016001
Martín-Lara MA, Iáñez-Rodríguez I, Blázquez G, Quesada L, Pérez A, Calero M (2017) Kinetics of termal decomposition of some biomasses in an inert environment. An investigation of the effect of lead loaded by biosorption. Waste Manag. https://doi.org/10.1016/j.wasman.2017.09.021
McCabe WL, Smith JC, Harriott P (1993) Unit operations of chemical engineering, 5th edn. McGraw-Hill, New Delhi
Mishra A, Tripathi BD, Rai AK (2016) Packed-bed column biosorption of Cr (VI) and Ni (II) onto fenton modified Hydrilla verticillata dried biomass. Ecotoxicol Environ Saf 132:420–428
Mushtaq M, Bhatti N, Iqbal M, Noreen S (2016) Eriobotrya japonica seed biocomposite efficiency for copper adsorption: isoterms, kinetics, thermodynamic and desorption studies. J Environ Manag 176:21–33
Nadeem R, Manzoor Q, Iqbal M, Nisar J (2016) Biosorption of Pb (II) onto immobilized and native Mangifera indica waste biomass. J Ind Eng Chem 35:185–194
Plazinski W, Rudzinski W (2010) A novel two-resistance model for description of the adsorption kinetics onto porous particles. Langmuir 26:802–808
Rashid A, Bhatti HN, Iqbal M, Noreen S (2016) Fungal biomass composite with bentonite efficiency for nickel and zinc adsorption: a mechanistic study. Ecol Eng 91:459–471
Sharma R, Singh B (2013) Removal of Ni (II) ions from aqueous solutions using modified rice straw in a fixed bed column. Bioresour Technol 146:519–524
Sulaymon AH, Yousif SA, Al-Faize MM (2014) Competitive biosorption of lead mercury chromium and arsenic ions onto activated sludge in fixed bed adsorber. J Taiwan Inst Chem E 45:325–337
Tahir N, Bhatti HN, Iqbal M, Noreen S (2017) Biopolymers composites with peanut hull waste biomass and application for crystal violet adsorption. Int J Biol Macromol 94:210–220
Tan HKS, Spinner IH (1994) Multicomponent ion exchange column dynamics. Can J Chem Eng 72:330–341
Tchounwou PB, Yedjou CG, Patlolla AK, Sutton DJ (2012) Heavy metals toxicity and the environment. EXS 101:133–164
Treybal RE (1993) Mass transfer operations, 2nd edn. McGraw-Hill, New Delhi
Vicente IA (2011) Tecnología sostenible para la obtención de un biosorbente de metales pesados a partir del bagazo de caña de azúcar. PhD Thesis, Universidad Central “Marta Abreu” de Las Villas, Santa Clara
Yang J, Volesky B (1996) Intraparticle diffusivity of Cd ions in a new biosorbent material. J Chem Technol Biotechnol 66:355–364
Acknowledgement
The authors thank the Central University “Marta Abreu” of Las Villas, Cuba, for providing the means to carry out this work.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Rico, I.L.R., Carrazana, R.J.C., Karna, N.K. et al. Modeling the mass transfer in biosorption of Cr (VI) y Ni (II) by natural sugarcane bagasse. Appl Water Sci 8, 55 (2018). https://doi.org/10.1007/s13201-018-0692-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s13201-018-0692-z