Abstract
This paper deals with the Markov modeling and reliability analysis of urea synthesis system of a fertilizer plant. This system was modeled using Markov birth–death process with the assumption that the failure and repair rates of each subsystem follow exponential distribution. The first-order Chapman–Kolmogorov differential equations are developed with the use of mnemonic rule and these equations are solved with Runga–Kutta fourth-order method. The long-run availability, reliability and mean time between failures are computed for various choices of failure and repair rates of subsystems of the system. The findings of the paper are discussed with the plant personnel to adopt and practice suitable maintenance policies/strategies to enhance the performance of the urea synthesis system of the fertilizer plant.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
The system reliability has great significance in recent years due to competitive environment. Reliability is defined as the ability of a system to perform the required function under stated conditions for a specified period of time. The reliability of a complex system can be obtained by either increasing the capacity of the system or providing sufficient redundant part(s) with perfect switch over devices. Kumar and Tewari (2008, 2009) presented a simulation model for evaluating the performance of CO-shift conversion system and urea decomposition system in a fertilizer plant. Dhillon and Singh (1981) and Kumar et al. (1989, 2007) used Markov model for performance analysis of paper and fertilizer plants. Arora and Kumar (1997) discussed the availability analysis of steam and powder generation systems of thermal power plants. Gupta and Tewari (2011) presented the availability model for a thermal power plant. Khanduja et al. (2012) presented the steady-state behavior and maintenance planning of bleaching system of a paper plant. Kumar and Tewari (2011) discussed the mathematical modeling and performance optimization of CO2 cooling system of a fertilizer plant using the genetic algorithm. Dhople et al. (2014) provided a framework to analyze Markov reward models used in system performability analysis. Tewari et al. (2012) computed the steady-state availability and performance optimization for the crystallization unit of a sugar plant by using genetic algorithm. Kiilumen and Frisk (2014) developed a method to examine the long-term reliability of an anisotropic conductive adhesive (ACA)-attached polyethylene terephthalate (PET) flex-on-board (FOB) assembly for industrial application used in harsh environments. Ahmed et al. (2014) provided a risk-based stochastic modeling approach using a Markov decision process to assess the availability of a processing unit, which is referred to as the risk-based availability Markov model (RBAMM). Kumar et al. (2011) discussed the performance analysis of the furnace draft air cycle of a thermal power plant. Kadiyan et al. (2012) discussed the availability and reliability analysis of an uncaser system for a brewery plant. Singh and Goyal (2013) presented a methodology to study the steady-state behavior of repairable mechanical biscuit shaping system pertaining to a biscuit-manufacturing plant. Kumar and Mudgil (2014) discussed the availability analysis of the ice cream-making unit of a milk plant.
The literature revealed that the methods used by the different authors involve complex computations and the problem of determining long-run or steady-state availability of the system has been extensively studied. In this paper, a numerical method, i.e., Runge–Kutta fourth-order method is used to compute the MTBF and reliability of the urea synthesis system of a fertilizer plant. The values of failure and repair rates of all the subsystems of urea synthesis system were collected from maintenance history sheets and discussion with maintenance personnel of a fertilizer plant situated at Panipat, Haryana (India). The fertilizer plant comprises many systems, viz. urea synthesis system, urea decomposition system, urea crystallization system, urea prilling system, etc. The urea synthesis system is important for a fertilizer plant. This paper has been organized into six sections. The present section is the introductory type including the concerned literature review. In second section presents the “Mathematical aspects of reliability and availability”, whereas the third section concerned with “System description, assumptions and notations”. In fourth section deals with “Mathematical modeling of urea synthesis system”. “Performance analysis of the system” concerns in the fifth section. Finallly, sixth section deals with “Discussion and conclusion”.
Mathematical aspects of reliability and availability
Reliability
Reliability is the probability for failure-free operation of a system during a given interval of time, i.e., it is a measure of success for a failure-free operation. The reliability of a component may be calculated as:
where α is the constant failure rate of the component (per hour) and t is the operation time (hour).
Availability
Availability is the probability that a component or system is performing its required function at a given point in time when used under stated operating conditions. It is calculated by the ratio between lifetime and total time between failures of the equipment.
Mean time between failures (MTBF)
MTBF is the amount of failures per million hours for a component. It is commonly used as a variable in reliability and maintainability analysis as
Markov approach
Arora and Kumar (1997), Bradley and Dawson (1998), Dhillon and Singh (1981), Kumar et al. (1993, 2007) and Bhamare et al. (2008) used the Markov approach for availability analysis of different process plants. According to Markov, if P0(t) represents the probability of zero occurrences in time t, the probability of zero occurrences in time (t + ∆t) is given by the Eq. (1)
Similarly,
where α is the failure rate and β is the repair rate of the component or subsystem respectively.
The Eq. (2) shows that the probability of one occurrence in time \( (t + \Delta t) \) is composed of two parts:
-
probability of zero occurrences in time t multiplied by the probability of one occurrence in time interval \( \Delta t \) and
-
probability of one occurrence in time t multiplied by the probability of no occurrences in the interval \( \Delta t \).
After simplifying and taking ∆t → 0, the Eq. (2) is reduced to
Using the concept used in Eq. (3), the equations for transient and steady states are derived.
System description, assumptions and notations
System description
The urea synthesis system comprises a compressor used to compress the carbon dioxide, two reciprocating pumps used to boost the pressure of liquid ammonia and heaters used to heat ammonia gas. In this process, the CO2 gas and liquid ammonia (NH3) available from the ammonia production process are fed to the urea synthesis reactor. In the reactor these gases react to form urea in gaseous form. The urea synthesis system comprises five subsystems arranged in series as (Fig. 1):
-
1.
Subsystem A1: It has CO2 booster compressor as a single unit arranged in series. Its failure causes the complete failure of the system.
-
2.
Subsystem A2: It has CO2 compressor as a single unit arranged in series. Failure of this subsystem causes the complete failure of the system.
-
3.
Subsystem A3: It consists of three NH3 pre-heaters units arranged in series. Failure of any one of these causes the complete failure of the system.
-
4.
Subsystem H: It consists of four liquid ammonia feed pumps arranged in parallel. Two pumps remain operative in parallel and the other two in cold standby. Failure of three pumps at a time will cause complete failure of the system.
-
5.
Subsystem L: It consists of three recycle solution feed pumps arranged in parallel. Failure of any one unit reduces the capacity of the system, but complete failure occurs when failure of all units takes place at a time.
Assumptions
-
The failure and repair rates are constant over time, statistically independent of each other and there are no simultaneous failures among the subsystems as stated by Kumar and Kumar (2011).
-
There are sufficient repair or replacement facilities, i.e., no waiting time to start the repairs. The failure or repair of the system follows exponential distribution as stated by Srinath (1994).
-
A repaired system is as good as new, performance-wise, as stated by Khanduja et al. (2008).
-
The switchover devices used for standby subsystems are perfect.
Notations
- :
-
Full working state of the system
- :
-
Reduced state of the system
- :
-
Failed state of the system
- P 0 (t):
-
Probability of the system working with full capacity at time t
- P 1 (t), P 6 (t):
-
Probability of the system in cold standby state
- P 2, (t) to P 5, (t), P 7, (t),P 8, (t):
-
Probability of the system in reduced capacity state
- P 9 (t) to P 41 (t):
-
Probability of the system in failed state
- α i; i = 1,2,3,4,5:
-
Mean failure rates of A1, A2, A3, H and L, respectively
- ß i; i = 1,2,3,4,5:
-
Mean repair rates of A1, A2, A3, H and L, respectively, and
- d/dt:
-
derivative w.r.t. t
Mathematical modeling of the urea synthesis system
The mathematical modeling of the system is carried out using simple probabilistic considerations and Chapman–Kolmogorov differential equations are developed based on Markov birth–death process. The Chapman–Kolmogorov differential equations are derived by using the mnemonic rule as stated by Khanduja et al. (2008). According to the mnemonic rule, the derivative of the probability of every state is equal to the sum of all probability flows which comes from other states to the given state minus the sum of all probability flows which goes out from the given state to the other states. The transition diagram (Fig. 2) depicts a simulation model showing all the possible states of the urea synthesis system.
Thus, the equations for transient state and steady state of the urea synthesis system are derived as follows.
Transient state
Mathematical Eqs. (4)–(17) are developed by applying Markov birth–death process to each state one by one out of 41 states of transition diagram (Fig. 2) as explained by Garg et al. (2010a, b):
where i = 9,12,15,18,21,25,28,32,35 and j = 0,1,2,3,4,5,6,7,8, respectively.
where i = 10, 13, 16, 19, 22, 26, 29, 33, 36 and j = 0, 1, 2, 3, 4, 5, 6, 7, 8, respectively.
where i = 11, 14, 17, 20, 23, 27, 30, 34, 37 and j = 0, 1, 2, 3, 4, 5, 6, 7, 8, respectively.
where i = 24, 40, 39 and j = 4, 5, 8, respectively.
where i = 31, 41, 38 and j = 6, 7, 8, respectively.
The initial conditions are:
The system of differential Eqs. (4)–(17) with initial conditions given by Eq. (18) was solved by Runge–Kutta fourth-order method. The numerical computations were carried out by taking time t = 0 to t = 360 days for different choices of failure and repair rates of the subsystems. The data regarding failure and repair rates of all the subsystems were taken from the plant personnel as stated earlier.
Reliability R(t) of the system is the sum of the reliabilities of the system working under full capacity and reduced state, i.e.,
Equation (19) is used to compute the reliability of the urea synthesis system, where P0(t) is the probability of the system working with full capacity, P 1(t) and P 6(t) are the probability of the system working under cold standby state and P 2(t), P 3(t), P 4(t), P 5(t), P 7(t) and P 8(t) are the probability of the system working with reduced capacity.
Steady state
Arora and Kumar (1997) stated that in process plant or industries, the management is interested in getting the long-run availability of the system. The steady-state probabilities of the system are obtained by imposing the following restrictions: d/dt → 0, as t → ∞. Thus, the long-run availability, i.e., A(∞) of the urea synthesis system is obtained by putting derivative of all probabilities equal to zero, i.e.,
where i = 9,12,15,18,21,25,28,32,35 and j = 0,1,2,3,4,5,6,7,8 respectively.
where i = 9,12,15,18,21,25,28,32,35 and j = 0,1,2,3,4,5,6,7,8, respectively.
where i = 9,12,15,18,21,25,28,32,35 and j = 0,1,2,3,4,5,6,7,8. respectively.
where i = 24, 40, 39 and j = 4, 5, 8, respectively.
where i = 31, 41, 38 and j = 6, 7, 8, respectively.
Thus, by putting the values of probabilities from Eqs. (20)–(24) in Eqs. (4)–(17),
finally, we get
Solving these equations recursively,
where \( C_{17} = \, C_{14} + C_{15} + C_{16} / \, \left( {1 + C_{12} } \right) \, + C_{11} / \, (C_{13} / \, \left( {1 + C_{12} } \right) \, + C_{10} ; \)
where \( C_{19} = \, \left( {C_{1} - \left( {\beta_{5} C_{16} } \right)} \right)/\beta_{4} ; \)
where \( C_{18} = \left( {C_{13} /\left( {1 + C_{12} } \right)C_{17} } \right) - C_{16} ; \)
where C 21 = ((C 3 C 19) − α 4 − (β 5 C 18))/C 3;
where C 22 = ((C 5 C 21) – (α 4 C 19))/β 5;
where C 20 = ((C 2 C 17) – α 5 – (β 4 C 18))/β 5;
where C 23 = ((C 7 C 20) – (α 5 C 17))/β 5;
where C 24 = ((α 4 C 23) + (α 5C22)).
The probability of full working capacity, i.e., P 0 is determined by using normalizing condition: (i.e., sum of the probabilities of all working states, reduced capacity and failed states is equal to 1), i.e.,
where
Now, the steady state availability A(∞) of urea synthesis system may be obtained as summation of all working and reduced capacity state probabilities, i.e.,
Eq. (42) is used to get the long-run availability of the urea synthesis system.
Performance analysis of the system
This section includes the following
• The computation of long-run availability of the system.
• The computation of reliability and mean time between failures (MTBF) of the system.
Long-run availability of the system
The long-run availability of the system is computed by using Eq. (42), and the effect of change in failure and repair rates of subsystems on long-run availability of the system is presented in Tables 1, 2, 3, 4 and 5.
Effect of failure and repair rates of subsystem A1 on long-run availability of the system
The effect of failure and repair rates of subsystem A1 on long-run availability of the system is studied by varying their values as α 1 = 0.004, 0.005, 0.006, 0.007 and β 1 = 0.35, 0.4, 0.45, 0.5. The failure and repair rates of other subsystems are kept constant as α 2 = 0.005, α 3 = 0.001, α 4 = 0.002, α 5 = 0.004, β 2 = 0.1, β 3 = 0.5, β 4 = 0.1, β 5 = 0.4. The long-run availability of the system is calculated using these data and the results are shown in Table 1. Table 1 shows that increase in failure rate (α 1) of subsystem A 1 causes decrease in long-run availability of the system from 0.794 to 0.559 % approximately, but increase in repair rate (β 1) of subsystem A1 causes increase in long-run availability of the system from 0.32 to 0.56 %.
Effect of failure and repair rates of subsystem A2 on long-run availability of the system
The effect of failure and repair rates of subsystem A2 on long-run availability of the system is studied by varying their values as α 2 = 0.004, 0.005, 0.006, 0.007 and β 2 = 0.05, 0.1, 0.15, 0.2. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 3 = 0.001, α 4 = 0.002, α 5 = 0.004, β 1 = 0.4, β 3 = 0.5, β 4 = 0.1, β 5 = 0.4. Table 2 shows that increase in failure rate (α 2) of subsystem A 2 causes decrease in long-run availability of the system from 5.16 to 1.418 % approximately, but increase in repair rate (β 2) of subsystem A 2 causes increase in long-run availability of the system from 5.76 to 9.93 %.
Effect of failure and repair rates of subsystem A3 on long-run availability of the system
The effect of failure and repair rates of subsystem A3 on long-run availability of the system is studied by varying their values as α 3 = 0.0005, 0.001, 0.0015, 0.002 and β 3 = 0.4, 0.5, 0.6, 0.7. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 4 = 0.002, α 5 = 0.004, β 1 = 0.4, β 2 = 0.1, β 4 = 0.1, β 5 = 0.4. Table 3 shows that increase in failure rate (α 3) of subsystem A 3 causes decrease in long-run availability of the system from 0.299 to 0.221 % approximately, but increase in repair rate (β 3) of subsystem A3 causes increase in long-run availability of the system from 0.03 to 0.10 %.
Effect of failure and repair rates of subsystem H on long-run availability of the system
The effect of failure and repair rates of subsystem H on long-run availability of the system is studied by varying their values as α 4 = 0.001, 0.002, 0.003, 0.004 and β 4 = 0.05, 0.1, 0.15, 0.2. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 3 = 0.001, α 5 = 0.004, β 1 = 0.4, β 2 = 0.1, β 3 = 0.5, β 5 = 0.4. Table 4 shows that increase in failure rate (α 4) of subsystem H causes decrease in long-run availability of the system from 0.06 to 0.123 % approximately, but increase in repair rate (β 4) of subsystem H causes decrease in long-run availability of the system from 0.032 to 0.095 %.
Effect of failure and repair rates of subsystem L on long-run availability of the system
The effect of failure and repair rates of subsystem L on long-run availability of the system is studied by varying their values as α 5 = 0.003, 0.004, 0.005, 0.006 and β 5 = 0.3, 0.4, 0.5, 0.6. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 3 = 0.001, α 4 = 0.002, β 1 = 0.4, β 2 = 0.1, β 3 = 0.5, β 4 = 0.1. Table 5 shows that increase in failure rate (α 5) of subsystem L causes decrease in long-run availability of the system from 0.547 to 0.384 % approximately, but increase in repair rate (β 5) of subsystem L causes increase in long-run availability of the system from 0.21 to 0.37 %.
Reliability of the system
Some methods such as Laplace transformation, Lagrange’s and matrix methods are available to solve the governing differential equations, but these methods are not advisable for use if the system is complex and has a large number of differential equations. Therefore, Runge–Kutta fourth-order method is used to solve these differential equations.
Effect of failure and repair rates of subsystem A1 on the reliability of the system
The effect of failure rates of subsystem A 1 on the reliability of the system is studied by varying their values as α 1 = 0.004, 0.005, 0.006, 0.007 at β 1 = 0.4. The failure and repair rates of other subsystems are kept constant as α 2 = 0.005, α 3 = 0.001, α 4 = 0.002, α 5 = 0.004, β 2 = 0.1, β 3 = 0.5, β 4 = 0.1, β 5 = 0.4. The reliability of the system is calculated with these data and the results are shown in Table 6. This table shows that the reliability of the system decreases by 0.019 % approximately with the increase of time. However, it decreases from 0.7032 to 0.7015 % approximately and MTBF decreases from 339 to 336.7 days when the failure rate varies from 0.004 to 0.007.
The effect of repair rates of subsystem A 1 on the reliability of the system is studied by varying their values as β 1 = 0.3, 0.4, 0.5, 0.6 at α 1 = 0.005. The failure and repair rates of other subsystems are kept constant as α 2 = 0.005, α 3 = 0.001, α 4 = 0.002, α 5 = 0.004, β 2 = 0.1, β 3 = 0.5, β 4 = 0.1, β 5 = 0.4. The reliability of the system is calculated with these data and the results are shown in Table 6. This table shows that the reliability of the system decreases by 0.185 % approximately with the increase of time. However, it increases from 0.7864 to 0.790 % approximately and MTBF increases from 336.97 to 339.62 days when the failure rate varies from 0.3 to 0.6.
Effect of failure and repair rates of subsystem A2 on the reliability of the system
The effect of failure rates of subsystem A 2 on the reliability of the system is studied by varying their values as α 2 = 0.004, 0.005, 0.006, 0.007 at β 2 = 0.1. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 3 = 0.001, α 4 = 0.002, α 5 = 0.004, β 1 = 0.4, β 3 = 0.5, β 4 = 0.1, β 5 = 0.4. The reliability of the system is calculated with these data and the results are shown in Table 7. This table shows that the reliability of the system decreases from 0.253 to 0.149 % approximately with the increase of time. However, it decreases from 2.76 to 2.66 % approximately and MTBF decreases from 332 to 313 days when the failure rate varies from 0.004 to 0.007.
The effect of repair rates of subsystem A2 on the reliability of the system is studied by varying their values as β 2 = 0.05, 0.1, 0.15, 0.2 at α 2 = 0.005. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 3 = 0.001, α 4 = 0.002, α 5 = 0.004, β 1 = 0.4, β 3 = 0.5, β 4 = 0.1, β 5 = 0.4. The reliability of the system is calculated with these data and the results are shown in Table 7. This table shows that the reliability of the system decreases from 1.832 to 0.007 % approximately with the increase of time. However, it increases from 5.23 to 7.0 % approximately and MTBF increases from 323.68 days to 346.36 days when the repair rate varies from 0.05 to 0.2.
Effect of failure and repair rates of subsystem A3 on the reliability of the system
The effect of failure rates of subsystem A3 on the reliability of the system is studied by varying their values as α 3 = 0.0005, 0.001, 0.0015, 0.002 at β 3 = 0.5. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 4 = 0.002, α 5 = 0.004, β 1 = 0.4, β 2 = 0.1, β 4 = 0.1, β 5 = 0.4. The reliability of the system is calculated with these data and results are shown in Table 8. This table shows that the reliability of the system decreases by 0.185 % approximately with the increase of time. However, it decreases by 0.282 % approximately and MTBF decreases from 338.6 days to 337.65 days when the failure rate varies from 0.0005 to 0.002.
The effect of repair rates of subsystem A3 on the reliability of the system is studied by varying their values as β 3 = 0.4, 0.5, 0.6, 0.7 at α 3 = 0.001. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 4 = 0.002, α 5 = 0.004, β 1 = 0.4, β 2 = 0.1, β 4 = 0.1, β 5 = 0.4. The reliability of the system is calculated with these data and results are shown in Table 8. This table shows that the reliability of the system decreases by 0.185 % approximately with the increase of time. However, it increases by 0.101 % approximately and MTBF increases from 338.13 to 338.47 days when the repair rate varies from 0.4 to 0.7.
Effect of failure and repair rates of subsystem H on the reliability of the system
The effect of failure rates of subsystem (H) on the reliability of the system is studied by varying their values as α 4 = 0.001, 0.002, 0.003, 0.004 at β 4 = 0.1. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 3 = 0.001, α 5 = 0.004, β 1 = 0.4, β 2 = 0.1, β 3 = 0.5, β 5 = 0.4. The reliability of the system is calculated with these data and results are shown in Table 9. This table shows that the reliability of the system decreases from 0.197 to 0.165 % approximately with the increase of time. However, it decreases from 0.013 to 0.001 % and MTBF decreases from 338.32 to 338.27 days when the failure rate varies from 0.001 to 0.004.
The effect of the repair rates of subsystem H on the reliability of the system is studied by varying their values as β 4 = 0.05, 0.1, 0.15, 0.2 at α 4 = 0.002. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 3 = 0.001, α 5 = 0.004; β 1 = 0.4, β 2 = 0.1, β 3 = 0.5, β 5 = 0.4. The reliability of the system is calculated with these data and results are shown in Table 9. This table shows that the reliability of the system decreases from 0.197 to 0.168 % approximately with the increase of time. However, it increases from 0.0002 to 0.0125 % and MTBF increases from 338.27 to 338.31 days when the repair rate varies from 0.05 to 0.2.
Effect of failure and repair rates of subsystem L on the reliability of the system
The effect of failure rates of subsystem L on the reliability of the system is studied by varying their values as α 5 = 0.003, 0.004, 0.005, 0.006 at β 5 = 0.4. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 3 = 0.001, α 4 = 0.002, β 1 = 0.4, β 2 = 0.1, β 3 = 0.5, β 4 = 0.1. The reliability of the system is calculated with these data and results are shown in Table 10. This table shows that the reliability of the system decreases from 0.197 to 0.156 % approximately with the increase of time. However, it decreases from 0.0215 to 0.0019 % approximately and MTBF decreases from 338.34 days to 338.27 days when the failure rate varies from 0.003 to 0.006.
The effect of repair rates of subsystem (L) on the reliability of the system is studied by varying their values as β 5 = 0.3, 0.4, 0.5, 0.6 at α 5 = 0.004. The failure and repair rates of other subsystems are kept constant as α 1 = 0.005, α 2 = 0.005, α 3 = 0.001, α 4 = 0.002; β 1 = 0.4, β 2 = 0.1, β 3 = 0.5, β 4 = 0.1. The reliability of the system is calculated with these data and the results are shown in Table 10. This table shows that the reliability of the system decreases from 0.197 to 0.168 % approximately with the increase of time. However, it increases by 0.008 % and MTBF increases from 338.28 days to 338.27 days when the repair rate varies from 0.3 to 0.6.
Effect of failure and repair rates of subsystems on the long-run availability of the system
Table 11 shows the effect of change in failure and repair rates of subsystems on change (%) in the long-run availability of the system. Table 11 concludes that the change (%) in the long-run availability of the system is maximum with the change in failure and repair rate of subsystem A2 and the same is shown in Fig. 3.
Effect of failure and repair rates of subsystems on the reliability of the system
Table 12 shows the effect of change in failure and repair rates of subsystems on change (%) in reliability of the system. Table 12 concludes that the change (%) in reliability of the system is maximum with the change in failure and repair rate of subsystem A2 and the same is shown in Fig. 4a, b. Figure 5 shows the effect of failure and repair rate of subsystem A2 on system reliability (%).
Discussion and conclusion
The proposed method is easy for use for in the complex system having a large number of differential equations and it helps to compute the long-run availability, reliability and mean time between failures (MTBF) of the urea synthesis system of the fertilizer plant. Table 11 concludes that the long-run availability of the system improved from 5.162 to 9.93 %, while Table 12 concludes that the reliability of the system improved from 2.767 to 7.217 % by controlling the failure rate and repair rate of subsystem A2. Thus, the long-run availability and reliability of the system can be improved significantly by the proper maintenance planning of subsystem A2. The other subsystems also affect the long-run availability and reliability of the system, but these are lesser effective than subsystem A2. These findings of this paper are discussed with the management of the plant and these results are found to be highly beneficial for the performance evaluation and to enhance the production and quality of urea.
References
Ahmed Q, Faisal IK, Syed AR (2014) A risk-based availability estimation using Markov method. Int J Qual Reliab Manage 31(2):106–128
Arora N, Kumar D (1997) Availability analysis of steam and power generation system in thermal power plant. Microelectron Reliab 37(5):795–799
Bhamare SS, Yaday OP, Rathore A (2008) Evolution of reliability engineering discipline over the last six decades: a comprehensive review. Int J Reliab Saf 1(4):377–410
Bradley ML, Dawson R (1998) The cost of unreliability: a case study. J Qual Maint Eng 4(3):212–218
Dhillon BS, Singh C (1981) Engineering reliability: new techniques and applications. Willey, New York
Dhople SV, DeVille L, Domínguez-García AD (2014) A Stochastic hybrid systems framework for analysis of Markov reward models. Reliab Eng Syst Saf 123(3):158–170
Garg D, Kumar K, Singh J (2010a) Availability analysis of a cattle feed plant using matrix method. Int J Eng 3(2):201–219
Garg S, Singh J, Singh DV (2010b) Availability analysis of crank-case manufacturing in a two-wheeler automobile industry. Appl Math Model 34:1672–1683
Gupta S, Tewari PC (2011) Simulation modeling in a availability thermal power plant. J Eng Sci Technol Rev 4(2):110–117
Kadiyan S, Garg RK, Gautam R (2012) Reliability and availability analysis of uncaser system in a brewery plant. Int J Res Mech Eng Technol 2(2):7–11
Khanduja R, Tewari PC, Kumar D (2008) Availability analysis of bleaching system of a paper plant. J Ind Eng 32(1):24–29
Khanduja R, Tewari PC, Kumar D (2012) Steady state behavior and maintenance planning of bleaching system in a paper plant. Int J Ind Eng 7(12):39–44
Kiilunen J, Frisk L (2014) Reliability analysis of an ACA attached flex-on-board assembly for industrial application. Solder Surf Mount Technol 26(2):62–70
Kumar V, Mudgil V (2014) Availability optimization of ice cream making unit of milk plant using genetic algorithm. Int J Manag Bus Stud 4(3):17–19
Kumar S, Tewari PC (2008) Development of performance evaluating model for CO-Shift conversion system in the fertilizer plant. Int J Eng Res Ind Appl 1(6):369–382
Kumar S, Tewari PC (2009) Simulation model for evaluating the performance of urea decomposition system in a fertilizer plant. Int J Ind Eng Pract 1(1):10–14
Kumar S, Tewari PC (2011) Mathematical modeling and performance optimization of CO2 cooling system of a fertilizer plant. Int J Ind Eng Comput 2:689–698
Kumar D, Singh J, Pandey PC (1989) Availability analysis of the washing system in the paper industry. Microelectron Reliab 29:775–778
Kumar D, Singh J, Pandey PC (1993) Operational behavior and profit function for a bleaching and screening system in the paper industry. Microelectron Reliab 33:1101–1105
Kumar S, Tewari PC, Sharma R (2007) Simulated availability of CO2 cooling system in a fertilizer plant. Ind Eng J (Indian Inst Ind Eng, Mumbai) 36(10):19–23
Kumar R, Sharma AK, Tewari PC (2011) Performance modeling of furnace draft air cycle in a thermal power plant. Int J Eng Sci Technol 3(8):6792–6798
Singh P, Goyal A (2013) Behavior analysis of a biscuit making plant using Markov regenerative modeling. Int J Theor Appl Res Mech Eng 2(3):148–152
Srinath LS (1994) Reliability Engineering. East-West Press Pvt. Ltd, India
Tewari PC, Khanduja R, Gupta M (2012) performance enhancement for crystallization unit of a sugar plant using genetic algorithm. J Ind Eng Int 8(1):1–6
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are credited.
About this article
Cite this article
Aggarwal, A.K., Kumar, S., Singh, V. et al. Markov modeling and reliability analysis of urea synthesis system of a fertilizer plant. J Ind Eng Int 11, 1–14 (2015). https://doi.org/10.1007/s40092-014-0091-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40092-014-0091-5