Abstract
The friction and wear properties, as well as the scuffing resistance, of different piston-ring coatings mating with a chrome-plated cylinder liner were investigated. Interrupted wear tests under the lubricant starvation condition were conducted to examine the wear behavior of Cr-diamond coating (GDC) and diamond-like coating (DLC). The results indicated that the DLC coating had outstanding tribological properties (small coefficient of friction and wear loss) at 150 °C, while the GDC coating exhibited better performance at an elevated temperature (240 °C). The DLC coating had a better scuffing resistance; no material adhesion occurred for 70 min under the unlubricated condition. The interrupted wear behaviors revealed that the scuffing process of the GDC coating involved the consumption of lubricant oil with relatively stable wear, a reduction in the friction force, and the occurrence of scuffing, in sequence. In contrast, although the friction force also increased after a short period of weak friction, no scuffing was observed. This is attributed to the formation of a mixed oxide and graphitic C tribolayer.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Wong V W, Tung S C. Overview of automotive engine friction and reduction trends-Effects of surface, material, and lubricant-additive technologies. Friction 4(1): 1–28 (2016)
Martins R, Amaro R, Seabra J. Influence of low friction coatings on the scuffing load capacity and efficiency of gears. Tribol Int 41(4): 234–243 (2008)
Kamps T J, Walker J C, Wood R J, Lee P M, Plint A G. Reproducing automotive engine scuffing using a lubricated reciprocating contact. Wear 332–333: 1193–1199 (2015)
dos Santos Filho D, Tschiptschin A P, Goldenstein H. Effects of ethanol content on cast iron cylinder wear in a flex-fuel internal combustion engine—A case study. Wear 406–407: 105–117 (2018)
Rao X, Sheng C X, Guo Z W, Yuan C Q. Effects of thread groove width in cylinder liner surface on performances of diesel engine. Wear 426–427: 1296–1303 (2019)
Farfan-Cabrera L I, Gallardo-Hernández E A, Pérez-González J, Marín-Santibáñez B M, Lewis R. Effects of Jatropha lubricant thermo-oxidation on the tribological behaviour of engine cylinder liners as measured by a reciprocating friction test. Wear 426–427: 910–918 (2019)
Ajayi O O, Lorenzo-Martin C, Erck R A, Fenske G R. Scuffing mechanism of near-surface material during lubricated severe sliding contact. Wear 271(9–10): 1750–1753 (2011)
Friedrich C, Berg G, Broszeit E, Rick F, Holland J. PVD CrxN coatings for tribological application on piston rings. Surf Coat Technol 97(1–3): 661–668 (1997)
Erdemir A, Donnet C. Tribology of diamond-like carbon films: Recent progress and future prospects. J Phys D: Appl Phys 39(18): R311–R327 (2006)
Wang J J, Pu J B, Zhang G G, Wang L P. Architecture of superthick diamond-like carbon films with excellent high temperature wear resistance. Tribol Int 81: 129–138 (2015)
Huang R X, Ma S Q, Zhang M D, Xu J J, Wang Z Y. Dynamic deformation and failure process of quasi-closed-cell aluminum foam manufactured by direct foaming technique. Mater Sci Eng: A 756: 302–311 (2019)
Kusmanov S A, Silkin S A, Smirnov A A, Belkin P N. Possibilities of increasing wear resistance of steel surface by plasma electrolytic treatment. Wear 386–387: 239–246 (2017)
Liu K, Kang J J, Zhang G, Lu Z B, Yue W. Effect of temperature and mating pair on tribological properties of DLC and GLC coatings under high pressure lubricated by MoDTC and ZDDP. Friction 9(6): 1390–1405 (2021)
Wan S H, Li D S, Zhang G A, Tieu A K, Zhang B. Comparison of the scuffing behaviour and wear resistance of candidate engineered coatings for automotive piston rings. Tribol Int 106: 10–22 (2017)
Enthoven J, Spikes H A. Infrared and visual study of the mechanisms of scuffing. Tribol Trans 39(2): 441–447 (1996)
Cutiongco E C, Chung Y W. Prediction of scuffing failure based on competitive kinetics of oxide formation and removal: Application to lubricated sliding of AISI 52100 steel on steel. Tribol Trans 37(3): 622–628 (1994)
Hershberger J, Ajayi O O, Zhang J, Yoon H, Fenske G R. Evidence of scuffing initiation by adiabatic shear instability. Wear 258(10): 1471–1478 (2005)
Hershberger J, Ajayi O O, Zhang J, Yoon H, Fenske G R. Formation of austenite during scuffing failure of SAE 4340 steel. Wear 256(1–2): 159–167 (2004)
Markov D, Kelly D. Mechanisms of adhesion-initiated catastrophic wear: Pure sliding. Wear 239(2): 189–210 (2000)
Piekoszewski W, Szczerek M, Tuszynski W. The action of lubricants under extreme pressure conditions in a modified four-ball tester. Wear 249(3–4): 188–193 (2001)
Yagi K, Kajita S, Izumi T, Koyamachi J, Tohyama M, Saito K, Sugimura J. Simultaneous synchrotron X-ray diffraction, near-infrared, and visible in situ observation of scuffing process of steel in sliding contact. Tribol Lett 61(2): 19 (2016)
Matsuzaki Y, Yagi K, Sugimura J. In-situ fast and long observation system for friction surfaces during scuffing of steel. Wear 386–387: 165–172 (2017)
Ma S, Liu Y, Wang Z C, Wang Z, Huang R, Xu J. The effect of honing angle and roughness height on the tribological performance of CuNiCr iron liner. Metals 9(5): 487 (2019)
Ma S Q, Chen W B, Li C D, Jin M, Huang R X, Xu J J. Wear properties and scuffing resistance of the Cr-Al2O3 coated piston rings: The effect of convexity position on barrel surface. J Tribol 141(2): 021301 (2019)
Abdullah Tasdemir H, Wakayama M, Tokoroyama T, Kousaka H, Umehara N, Mabuchi Y, Higuchi T. The effect of oil temperature and additive concentration on the wear of non-hydrogenated DLC coating. Tribol Int 77: 65–71 (2014)
Qu J, Meyer H M III, Cai Z B, Ma C, Luo H. Characterization of ZDDP and ionic liquid tribofilms on non-metallic coatings providing insights of tribofilm formation mechanisms. Wear 332–333: 1273–1285 (2015)
Tas M O, Banerji A, Lou M, Lukitsch M J, Alpas A T. Roles of mirror-like surface finish and DLC coated piston rings on increasing scuffing resistance of cast iron cylinder liners. Wear 376–377: 1558–1569 (2017)
Bai C N, Gong Z B, An L L, Qiang L, Zhang J Y, Yushkov G, Nikolaev A, Shandrikov M, Zhang B. Adhesion and friction performance of DLC/rubber: The influence of plasma pretreatment. Friction 9(3): 627–641 (2021)
Acknowledgements
This research was supported by the Natural Science Foundation of Liaoning Province (2019-ZD-0165 and 2020-HYLH-47), the China Postdoctoral Science Foundation (2020M670729), and the National Natural Science Foundation of China (51979018).
Author information
Authors and Affiliations
Corresponding authors
Additional information
Zeyu MA. He received his B.S. and M.S. degrees from Anhui University of Technology (China, 2017) and Dalian Maritime University (China, 2021), respectively. He is currently a Ph.D. student at the School of Mechanical Engineering, Xi’an Jiaotong University, China. His current research is tribological properties of the surface modified piston rings under high intensified conditions.
Ruoxuan HUANG. He received his B.S. and Ph.D. degrees from Tianjin University (China, 2007) and Nanyang Technological University (Singapore, 2016), respectively. He is working as an associate professor in the Department of Materials Science and Engineering, Dalian Maritime University. His research interests cover the tribology in internal combustion engine and associated friction-reduction and anti-wear method. He has published 25 peer-reviewed papers indexed by SCI and obtained 4 licensed invention patents.
Xiaoshuai YUAN. She received her B.S. and M.S. degrees from Dalian Maritime University in 2010 and 2013, respectively. She is working at the China North Engine Research Institute. Her research interest is friction and wear in the piston ring-cylinder liner system.
Yan SHEN. He received his B.S. and Ph.D. degrees from Dalian Maritime University in 2003 and 2014, respectively. He is currently an associate professor at Dalian Maritime University. His research interests cover tribological design of diesel engine components, microtextured surface preparation and performance evaluation, and self-lubricating composites.
Jiujun XU. He received his B.S. and Ph.D. degrees from Dalian University of Technology (China, 1989) and Dalian Maritime University (China, 1996), respectively. He is working as a professor in the Department of Materials Science and Engineering, Dalian Maritime University. His research interests include the development of tribotest techniques for study tribology processes, especially for the key friction pairs in internal combustion engines. He has been awarded many prizes, including the second prize of the National Science and Technology Progress of China, the first prize of the National Defense Science and Technology Progress of China, and the first prize of the Science and Technology Progress of Liaoning province, etc. He has published over 70 peer-reviewed papers indexed by SCI and obtained more than 15 licensed invention patents. He recently wrote a book entitled Tribology in piston ring-cylinder liner system of diesel engine. It builds a bridge between the essential tribological findings and the engineering design, especially for the diesel engine used piston ring-cylinder liner system.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Ma, Z., Huang, R., Yuan, X. et al. Tribological performance and scuffing behaviors of several automobile piston rings mating with chrome-plated cylinder liner. Friction 10, 1245–1257 (2022). https://doi.org/10.1007/s40544-021-0530-4
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40544-021-0530-4