Abstract
Understanding the physical mechanisms that underpin the link between fluid injection and seismicity is essential in efforts to mitigate the seismic risk associated with subsurface technologies. To that end, here we develop a poroelastic model of earthquake nucleation based on rate-and-state friction in the manner of spring–sliders, and analyze conditions for the emergence of stick-slip frictional instability—the mechanism for earthquakes—by carrying out a linear stability analysis and nonlinear simulations. We find that the likelihood of triggering earthquakes depends largely on the rate of increase in pore pressure rather than its magnitude. Consequently, fluid injection at constant rate acts in the direction of triggering seismic rupture at early times followed by aseismic creep at late times. Our model implies that, for the same cumulative volume of injected fluid, an abrupt high-rate injection protocol is likely to increase the seismic risk whereas a gradual step-up protocol is likely to decrease it.
Similar content being viewed by others
Introduction
Subsurface fluid-injection operations have been recognized to carry a risk of inducing earthquakes since the 1960s1. While most of the injection-induced earthquakes are micro-tremors, they can occasionally be of large magnitude, such as the Prague Mw 5.7 earthquake in 20112, the Pawnee Mw 5.8 earthquake in 20163, and the Pohang Mw 5.5 earthquake in 20174, among others. The occurrence of induced earthquakes of large magnitude has motivated development of different operational strategies for seismic hazard mitigation. In particular, an early attempt to control seismicity at the Rangely oil field suggested maintaining the magnitude of fluid pressure below a critical threshold5, based on a Coulomb failure model that links the magnitude of fluid pressure to the occurrence of induced earthquakes6. This model, however, does not address the evolution of the rupture and whether a fault slips seismically or aseismically. It was also insufficient to explain seismicity at Cogdell oil field, for instance, where earthquakes were observed in regions of low rather than high fluid pressure7. A different strategy to control seismicity involved maintaining the cumulative volume of injected fluid below a critical threshold8, based on empirical observations and modeling linking the cumulative volume of injected fluid to the maximum magnitude of induced earthquakes9. This model, however, is at odds with the 2017 Pohang earthquake, as its magnitude exceeded the size estimated from the injected volume by 500 times10.
A growing number of field observations suggests that managing fluid injection rates may be a promising tool to mitigate the occurrence of induced earthquakes. It is observed that low-rate wells, for instance, are much less likely to be associated with earthquakes than high-rate wells, and that the critical rate above which earthquakes are induced is likely dependent on reservoir properties11,12. It is also observed that temporal variation in injection rates is generally correlated with the frequency of earthquakes1,13,14,15, and that abrupt increases in injection rates tend to shortly precede the occurrence of earthquakes16,17,18. While attempts have been made to explain some of these observations with seismicity-rate models19,20,21 and 2D numerical simulations of coupled flow-geomechanics22,23, the physical mechanisms behind the link between the rate of fluid injection and the occurrence of induced earthquakes remain poorly understood.
Seismicity-rate models based on the triggering-front concept consider the large-scale spatiotemporal effects of nonlinear diffusion on the probability of a given magnitude earthquake using Gutenberg–Richter statistics24, but do not address the dynamics of the rupture and, in particular, whether a fault slips seismically or aseismically. Characterizing fault slip mode is essential to mitigate the seismic risk associated with subsurface operations, as it has been observed that an increase in pore pressure magnitude leads to seismic slip in some sites1,2,3,4,5,25 and aseismic slip in others7,26,27,28,29,30. Here we develop a poroelastic model of induced earthquake nucleation in the manner of spring–sliders31,32,33,34,35 based on rate-and-state friction32,36, and we study the effect of injection rate on stick-slip frictional behavior—the mechanism for seismic slip37.
Our model shows that the likelihood of triggering earthquakes depends critically on the rate of increase in pore pressure. We find that fluid injection at constant rate acts in the direction of triggering seismic rupture at early times followed by aseismic creep at late times. This finding is qualitatively consistent with laboratory observations of sliding between saturated rocks at both transient and steady-state pore pressure conditions38,39,40, and may explain field observations of triggered and induced seismicity from subsurface operations in different geologic settings1,11,12,13,14,16,17,18.
Results and discussion
Poroelastic spring–slider model
When fluid is injected into a faulted reservoir, the pore pressure change induces effective stress variations in the reservoir and surrounding rock (Fig. 1a). To model the effects of variations in effective normal stress on a creeping fault segment, we develop a poroelastic spring–slider model of frictional slip (Fig. 1b). Our model consists of a slider of unit base area that is pulled by a spring whose end is constrained to move at a steady slip rate. The spring stiffness accounts for the elastic interaction of the sliding surface with the surrounding rock. The slider represents the injection-driven deformation process, where a piston is loaded vertically and compresses a spring inside a fluid-filled space. The vertical spring is analogous to the rock skeleton, while the fluid inside the slider represents fluid in the rock pores subject to increase from fluid injection and decrease from pressure diffusion. Our model accounts for the poroelastic coupling between the shear and effective normal stresses along the fault.
Frictional evolution is modeled by the rate-and-state constitutive laws32,36, which are capable of reproducing a wide range of observed seismic and aseismic fault behaviors ranging from preseismic slip and earthquake nucleation to coseismic rupture and earthquake afterslip41. These laws propose that the frictional shear stress is a function of the effective normal stress and a coefficient of friction that is dependent on slip rate and the state of the sliding surface. Since the effective normal stress varies as a result of fluid injection, we adopt Linker and Dieterich’s42 formulation for the coefficient of friction and couple it with a poroelastic model of pore pressure and rock deformation. We derive the poroelastic model from the principles of mass and momentum conservation, and find that pore pressure satisfies a diffusion equation that leads to transient behavior at early times and steady-state behavior at late times.
The dimensional equations describing the dynamic motion of the poroelastic spring–slider system with an evolving pore pressure take the form (see Supplementary Note 1 for the derivation of the equations):
where U is the relative displacement between the load point and the slider, \({\dot{\,\,( )}}\) denotes time derivative, V0 is the loading velocity, V is slip rate, T is the vibration period, ks is the shear stiffness, V* is a normalizing slip rate, μ* is a constant appropriate for steady-state at slip rate V*, \(\hat{a}\) and \(\hat{b}\) are experimentally derived parameters relating friction to changes in slip rate and state, respectively, Θ is a state variable describing the sliding surface, Σ is the total stress, P is the pressure inside the slider (pore pressure), dc is the characteristic slip distance, \(\hat{\alpha }\) is a scaling factor ranging from 0 to μ42,43, \({k}_{{\rm{n}}}^{{\rm{eff}}}\) is the effective normal stiffness (related to the uniaxial bulk modulus or the reciprocal of the uniaxial specific storage per diffusion length in a continuum), k is the permeability, η is fluid dynamic viscosity, L is the pressure diffusion length, P0 is the ambient pressure, and Q is the volumetric injection rate per unit area.
Choosing the following characteristic quantities: uc = dc, vc = V*, μc = μ*, pc = P0, τc = μ*(Σ − P0), θc = μ*, and tc = dc/V*, the equations describing the dynamic motion of the system, in dimensionless form, become (see Supplementary Note 2):
where κ = (ksdc)/τc, \(a=\hat{a}/{\mu }_{{\rm{c}}}\), \(b=\hat{b}/{\mu }_{{\rm{c}}}\), \(\alpha =\hat{\alpha }/{\mu }_{{\rm{c}}}\), ϵ = (T/2π)/tc, \(c={t}_{{\rm{c}}}/(\eta L/{k}_{{\rm{n}}}^{{\rm{eff}}}/k)\), \(r={t}_{{\rm{c}}}{k}_{{\rm{n}}}^{{\rm{eff}}}\), and q = Q/pc. The parameter κ is the normalized shear stiffness, and a, b, α are normalized frictional parameters. The parameter ϵ is the normalized oscillation period or ratio of inertial to state-evolution timescales, which may range from 10−8 to 10−6 depending on rupture diameter and shear wave speed. The parameter c is the normalized diffusivity or ratio of the pore pressure to the state-evolution timescales, which may range from 10−4 to 101 depending on reservoir permeability, uniaxial bulk modulus, and well-fault distance. The parameter rq is the normalized injection rate, which may range from 10−5 to 10−1 depending on injection rate and reservoir size.
Stability analysis
The stability of steady frictional sliding to small perturbations in velocity, which determines whether motion is by slow steady-sliding or violent stick-slip, depends on the evolution of the frictional resistance. Stick-slip occurs whenever a change of frictional resistance with sliding occurs at a rate greater than the loading system is capable of following31. At a constant pore pressure, linear stability analysis of the system about steady-state leads to the stability condition by Ruina32. Pore pressure, however, is not constant in time and its evolution depends on the injection rate and on the poroelastic and hydraulic parameters of the rupture. To quantify this, we carry out a linear stability analysis of the system about a quasi steady-state where sliding is steady but pore pressure is evolving as a result of fluid injection. We find that motion is by stick-slip when the dimensionless shear stiffness of the loading system is lower than a critical value (κ < κcrit) given by
and is by steady-sliding otherwise (κ > κcrit). Variables p and \(\dot{p}\) are dimensionless pore pressure magnitude and pore pressure rate, respectively, at any point in time. Accordingly, frictional instability for the spring–poroslider system with an evolving pore pressure depends not only on the magnitude of pore pressure, but also on the rate of change of pore pressure (Supplementary Notes 3, 4, 5, and 6 for the analysis of QSSA, derivation of Eq. (9), and validation against nonlinear simulations).
As pore pressure evolves from initial to steady-state conditions in response to fluid injection, we find that the competing effects of p and \(\dot{p}\) exhibit a transition in their dominance over frictional instability (Fig. 2a). The destabilizing effect of \(\dot{p}\) dominates when pore pressure grows rapidly at early times, resulting in an increase in critical stiffness (dashed curve in Fig. 2a). It then decreases as pore pressure diffuses and approaches steady state, giving rise to the stabilizing effect of p, which explains the decrease in critical stiffness at late times (dotted curve in Fig. 2a). This result is generally consistent with a linear stability analysis of slow slip with mildly rate-strengthening friction in a poroelastic continuum44, in which undrained slip-induced poroelastic pressure has a destabilizing effect and a sufficiently fast equilibration process has a stabilizing effect. In our analysis, the early-time destabilizing effect of \(\dot{p}\) is likely attributed to a short-term effect on contact interlocking, where a decrease in effective normal stress results in fault opening and loss of asperity contacts45. The late-time stabilizing effect of p, in contrast, is likely attributed to a long-term effect on interface locking. A low effective normal stress tends to reduce the degree of interface locking, and thus limit the magnitude of stress drops46,47,48.
This behavior is also qualitatively consistent with laboratory observations of sliding between saturated rocks at both transient and steady-state pore pressure conditions. The early-time destabilizing effect agrees with experimental studies showing that a gradual increase in pore pressure results in unstable slip during the transient-state, and that the degree of instability measured by the total slip, slip rate, and shear stress drop correlates with the rate of pore pressure increase38,39. The late-time stabilizing effect also agrees with another experimental study, showing that sliding between two rock surfaces is much more stable at high than at low steady-state pore pressure40. Sliding is observed to be by slow, steady-type motion at high pore pressure, and by stick-slip at low pore pressure. This behavior, however, is different from the observations of shearing granular fault gouge materials49,50, where the frictional parameter a−b is observed to decrease in magnitude with increasing steady-state pore pressure, an effect related to shear-induced dilatancy strengthening and pore compaction creep.
Application to the Denver earthquakes
Our findings, if they are applicable to natural faults, hold interesting and important implications for induced seismicity. The poroelastic spring–slider may be viewed as a simple model of a fault segment in contact with a reservoir, steady-sliding as an analog of aseismic creep, and stick-slip as a seismic wave-producing rupture cycle33,37. The spring stiffness scales inversely with the size of the fault segment51. Within this view, our findings may be generalized to indicate that a slowly creeping fault segment is destabilized and nucleates an earthquake if its size exceeds a critical value known as the nucleation length, which is inversely proportional to the critical stiffness in Eq. (9).
To bridge the gap between the analysis of the idealized poroelastic spring–slider model and the real world, we extend our instability criterion from dimensionless to dimensional form, and identify values of dimensionless parameters c and rq that correspond to a real-world setting. The 1960s Denver earthquakes is a good example of a real-world setting, where it is well-documented that injection of wastewater into the fractured Precambrian granite gneiss underneath the Rocky Mountain Arsenal triggered the earthquakes and where injection rate is directly related to the frequency of earthquakes52,53. We find that reasonable estimates of c and rq for this setting are in the order of 10−2 to 10−1 and 10−3 to 10−1, respectively. We then assess the effect of fluid pressurization by evaluating its contribution to the critical stiffness in Eq. (9). We find that a reasonable estimate for the increase in critical stiffness at early times is ~300%, which indicates that the weakening effect from fluid pressurization is likely significant in this setting (see Supplementary Note 7 for more details on the application to the Denver earthquakes).
When earthquakes nucleate on a fault with velocity-weakening friction, in general, aseismic creep may begin in sections of favorable stress conditions. The aseismically creeping segment then slowly grows in size until it reaches the nucleation length, and then it breaks out rapidly into a seismic wave-producing rupture54. A significant increase in critical stiffness, or equivalently decrease in nucleation length, from fluid pressurization may further facilitate or exacerbate this breakout—potentially increasing the likelihood of triggering earthquakes.
Influence of reservoir properties on injection-induced seismicity
To study the influence of reservoir properties on the critical injection rate, above which earthquakes are induced, we model the occurrence of earthquakes as a function of dimensionless injection rate \(rq={d}_{{\rm{c}}}{k}_{{\rm{n}}}^{{\rm{eff}}}Q/({p}_{{\rm{c}}}{V}_{* })\) and normalized diffusivity \(c={d}_{{\rm{c}}}{k}_{{\rm{n}}}^{{\rm{eff}}}k/(\eta L{V}_{* })\) for velocity-weakening conditions, b − a > 0. We find that the dimensionless critical injection rate is directly proportional to the diffusivity c in the high-diffusivity limit, and independent of it in the low-diffusivity limit (Fig. 2b). These findings suggest that reservoir regions with low hydraulic diffusivity are more prone to induced seismicity than regions with high hydraulic diffusivity—a result that qualitatively agrees with the triggering-front concept24 (see Supplementary Note 8 for more details on the phase diagram of injection-induced seismicity).
Influence of injection strategy on induced seismicity
The earthquake likelihood is strongly dependent on the duration of injection. For a fixed total injected volume, a shorter injection duration (or, equivalently, a higher injection rate) results in a higher likelihood of earthquake triggering (Supplementary Note 9).
To further understand how injection rate may be used to minimize or mitigate the seismic hazard, we simulate three different injection scenarios, and examine the stability of each. Figure 3 demonstrates how injecting the same volume of fluid can have very different seismic potential depending on the injection profile. We observe that injecting at constant rate in scenario (A) causes the critical stiffness to increase at early times, potentially triggering earthquakes, and decrease at late times, potentially resulting in the cessation of earthquakes. In addition, we observe a dramatic drop in critical stiffness upon stopping injection followed by recovery to the value prior to injection. Scenario (B) shows that a higher injection rate yields higher critical stiffness, implying an increased risk of seismicity for this higher injection rate. Scenario (C), where the injection rate ramps up in stages, seems to be most stable because the maximum critical stiffness is lower than its value in both (A) and (B). If the duration of each stage is not sufficiently long for pressure to stabilize at the fault, the ramp-up injection strategy does not counteract the destabilizing effect of the rate of pore pressure increase at each injection rate increment. In the Basel enhanced geothermal site, for example, the duration of injection stages was 1 day55, while the time for pressure to stabilize at the fault is longer than 1 month—a conservative estimate based on the distance to the nearest fault segment to the injection well and the permeability of the fractured rock25,55. This suggests that a gradual increase in injection rate, where pore pressure is allowed to stabilize between injection stages, may be the safest injection strategy.
Summary and outlook
In summary, our model points to the underlying mechanism by which the rate of fluid pressurization, and hence the rate of effective normal stress unloading, may explain several injection-induced seismicity observations1,11,12,13,14,16,17,18. An abrupt or large increase in injection rate tends to intensify the early-time destabilizing effect of the rate of change in pore pressure on frictional sliding, whereas a gradual or small increase in injection rate tends to lessen it. Our findings, as a whole, suggest injection strategies to mitigate the seismic risk associated with a wide range of subsurface operations, from wastewater injection to geologic CO2 sequestration. Of course, a complex interplay of different mechanisms such as heterogeneous fault stresses, stress changes from aseismic slip, spatial growth of pore pressure diffusion, and static and dynamic stress transfer often play a role in the occurrence and, in particular, the timing of an earthquake4. This emphasizes the need to continue to develop and test new models for the forecast and control of induced seismicity10.
Methods
Methods described in the Supplementary Information
All methods and data are described in the Supplementary Information, including: (1) Derivation of the poroelastic spring–slider equations; (2) Governing equations in dimensionless form; (3) Linear stability analysis; (4) Nonlinear simulations; (5) Analytical vs. numerical estimates of critical stiffness; (6) Detailed discussion on the quasi-steady-state approximation; (7) Application to the Denver earthquakes; (8) Phase diagram of injection-induced seismicity; and (9) Earthquake likelihood vs. injection duration.
Data availability
All relevant data are available upon reasonable request from the authors.
Code availability
The simulation code is available upon reasonable request from the authors.
References
Healy, J., Rubey, W., Griggs, D. & Raleigh, C. The Denver earthquakes. Science 161, 1301–1310 (1968).
Keranen, K. M., Weingarten, M., Abers, G. A., Bekins, B. A. & Ge, S. Sharp increase in central Oklahoma seismicity since 2008 induced by massive wastewater injection. Science 345, 448–451 (2014).
Yeck, W. L. et al. Oklahoma experiences largest earthquake during ongoing regional wastewater injection hazard mitigation efforts. Geophys. Res. Lett. 44, 711–717 (2017).
Grigoli, F. et al. The November 2017 Mw 5.5 Pohang earthquake: a possible case of induced seismicity in South Korea. Science 360, 1003–1006 (2018).
Raleigh, C., Healy, J. & Bredehoeft, J. An experiment in earthquake control at Rangely, Colorado. Science 191, 1230–1237 (1976).
Hubbert, K. M. & Rubey, W. W. Role of fluid pressure in mechanics of overthrust faulting: I. mechanics of fluid-filled porous solids and its application to overthrust faulting. Geol. Soc. Am. Bull. 70, 115–166 (1959).
Davis, S. D. & Pennington, W. D. Induced seismic deformation in the Cogdell oil field of West Texas. Bull. Seismol. Soc. Am. 79, 1477–1495 (1989).
Hofmann, H. et al. First field application of cyclic soft stimulation at the Pohang Enhanced Geothermal System site in Korea. Geophys. J. Int. 217, 926–949 (2019).
McGarr, A. Maximum magnitude earthquakes induced by fluid injection. J. Geophys. Res. Solid Earth 119, 1008–1019 (2014).
Lee, K.-K. et al. Managing injection-induced seismic risks. Science 364, 730–732 (2019).
Frohlich, C. Two-year survey comparing earthquake activity and injection-well locations in the Barnett Shale, Texas. Proc. Natl Acad. Sci. USA 109, 13934–13938 (2012).
Weingarten, M., Ge, S., Godt, J. W., Bekins, B. A. & Rubinstein, J. L. High-rate injection is associated with the increase in US mid-continent seismicity. Science 348, 1336–1340 (2015).
Improta, L., Valoroso, L., Piccinini, D. & Chiarabba, C. A detailed analysis of wastewater-induced seismicity in the Val d’Agri oil field (Italy). Geophys. Res. Lett. 42, 2682–2690 (2015).
Langenbruch, C. & Zoback, M. D. How will induced seismicity in Oklahoma respond to decreased saltwater injection rates? Sci. Adv. 2, e1601542 (2016).
Barbour, A. J., Norbeck, J. H. & Rubinstein, J. L. The effects of varying injection rates in Osage County, Oklahoma, on the 2016 Mw 5.8 Pawnee earthquake. Seismol. Res. Lett. 88, 1040–1053 (2017).
Cuenot, N., Dorbath, C. & Dorbath, L. Analysis of the microseismicity induced by fluid injections at the EGS site of Soultz-sous-Forêts (Alsace, France): implications for the characterization of the geothermal reservoir properties. Pure Appl. Geophys. 165, 797–828 (2008).
Kim, W.-Y. Induced seismicity associated with fluid injection into a deep well in Youngstown, Ohio. J. Geophys. Res. Solid Earth 118, 3506–3518 (2013).
Tang, L., Lu, Z., Zhang, M., Sun, L. & Wen, L. Seismicity induced by simultaneous abrupt changes of injection rate and well pressure in Hutubi gas field. J. Geophys. Res. Solid Earth 123, 5929–5944 (2018).
Langenbruch, C., Weingarten, M. & Zoback, M. D. Physics-based forecasting of man-made earthquake hazards in Oklahoma and Kansas. Nat. Commun. 9, 3946 (2018).
Norbeck, J. & Rubinstein, J. L. Hydromechanical earthquake nucleation model forecasts onset, peak, and falling rates of induced seismicity in Oklahoma and Kansas. Geophys. Res. Lett. 45, 2963–2975 (2018).
Zhai, G., Shirzaei, M., Manga, M. & Chen, X. Pore-pressure diffusion, enhanced by poroelastic stresses, controls induced seismicity in Oklahoma. Proc. Natl Acad. Sci. USA 116, 16228–16233 (2019).
Torberntsson, K., Stiernström, V., Mattsson, K. & Dunham, E. M. A finite difference method for earthquake sequences in poroelastic solids. Comput. Geosci. 22, 1351–1370 (2018).
Pampillón, P., Santillán, D., Mosquera, J. C. & Cueto-Felgueroso, L. Dynamic and quasi-dynamic modeling of injection-induced earthquakes in poroelastic media. J. Geophys. Res. Solid Earth 123, 5730–5759 (2018).
Shapiro, S. & Dinske, C. Scaling of seismicity induced by nonlinear fluid-rock interaction. J. Geophys. Res. Solid Earth https://doi.org/10.1029/2008JB006145 (2009).
Majer, E. L. et al. Induced seismicity associated with enhanced geothermal systems. Geothermics 36, 185–222 (2007).
Guglielmi, Y., Cappa, F., Avouac, J.-P., Henry, P. & Elsworth, D. Seismicity triggered by fluid injection–induced aseismic slip. Science 348, 1224–1226 (2015).
Cornet, F., Helm, J., Poitrenaud, H. & Etchecopar, A. Seismic and aseismic slips induced by large-scale fluid injections. Pure Appl. Geophys. 150, 563–583 (1997).
Bourouis, S. & Bernard, P. Evidence for coupled seismic and aseismic fault slip during water injection in the geothermal site of Soultz (France), and implications for seismogenic transients. Geophys. J. Int. 169, 723–732 (2007).
Zoback, M. D. et al. The importance of slow slip on faults during hydraulic fracturing stimulation of shale gas reservoirs. In SPE Americas Unconventional Resources Conference (Society of Petroleum Engineers, 2012).
Wei, S. et al. The 2012 Brawley swarm triggered by injection-induced aseismic slip. Earth Planet. Sci. Lett. 422, 115–125 (2015).
Byerlee, J. The mechanics of stick-slip. Tectonophysics 9, 475–486 (1970).
Ruina, A. Slip instability and state variable friction laws. J. Geophys. Res. Solid Earth 88, 10359–10370 (1983).
Rice, J. R. & Tse, S. T. Dynamic motion of a single degree of freedom system following a rate and state dependent friction law. J. Geophys. Res. Solid Earth 91, 521–530 (1986).
Segall, P. & Rice, J. R. Dilatancy, compaction, and slip instability of a fluid-infiltrated fault. J. Geophys. Res. Solid Earth 100, 22155–22171 (1995).
Iverson, R. M. Regulation of landslide motion by dilatancy and pore pressure feedback. J. Geophys. Res. Earth Surf. 110, F02015 (2005).
Dieterich, J. H. Modeling of rock friction: 1. Experimental results and constitutive equations. J. Geophys. Res. Solid Earth 84, 2161–2168 (1979).
Brace, W. & Byerlee, J. Stick-slip as a mechanism for earthquakes. Science 153, 990–992 (1966).
Wang, L. et al. Laboratory study on fluid-induced fault slip behavior: The role of fluid pressurization rate. Geophys. Res. Lett. 47, e2019GL086627 (2020).
French, M. E., Zhu, W. & Banker, J. Fault slip controlled by stress path and fluid pressurization rate. Geophys. Res. Lett. 43, 4330–4339 (2016).
Byerlee, J. & Brace, W. Fault stability and pore pressure. Bull. Seismol. Soc. Am. 62, 657–660 (1972).
Marone, C. Laboratory-derived friction laws and their application to seismic faulting. Annu. Rev. Earth Planet. Sci. 26, 643–696 (1998).
Linker, M. & Dieterich, J. H. Effects of variable normal stress on rock friction: observations and constitutive equations. J. Geophys. Res. Solid Earth 97, 4923–4940 (1992).
Kilgore, B., Lozos, J., Beeler, N. & Oglesby, D. Laboratory observations of fault strength in response to changes in normal stress. J. Appl. Mech. 79, 031007 (2012).
Heimisson, E. R., Dunham, E. M. & Almquist, M. Poroelastic effects destabilize mildly rate-strengthening friction to generate stable slow slip pulses. J. Mech. Phys. Solids 130, 262–279 (2019).
Wang, W. & Scholz, C. Micromechanics of the velocity and normal stress dependence of rock friction. Pure Appl. Geophys. 143, 303–315 (1994).
Moreno, M., Rosenau, M. & Oncken, O. 2010 Maule earthquake slip correlates with pre-seismic locking of Andean subduction zone. Nature 467, 198–202 (2010).
Kitajima, H. & Saffer, D. M. Elevated pore pressure and anomalously low stress in regions of low frequency earthquakes along the Nankai Trough subduction megathrust. Geophys. Res. Lett. 39, L23301 (2012).
Segall, P., Rubin, A. M., Bradley, A. M. & Rice, J. R. Dilatant strengthening as a mechanism for slow slip events. J. Geophys. Res. Solid Earth https://doi.org/10.1029/2010JB007449 (2010).
Sawai, M., Niemeijer, A. R., Plümper, O., Hirose, T. & Spiers, C. J. Nucleation of frictional instability caused by fluid pressurization in subducted blueschist. Geophys. Res. Lett. 43, 2543–2551 (2016).
Scuderi, M. M. & Collettini, C. The role of fluid pressure in induced vs. triggered seismicity: Insights from rock deformation experiments on carbonates. Sci. Rep. 6, 24852 (2016).
Scholz, C. H. Earthquakes and friction laws. Nature 391, 37 (1998).
Evans, D. M. The Denver area earthquakes and the Rocky Mountain Arsenal disposal well. Mt. Geologist 3, 23–36 (1966).
Healy, J., Rubey, W., Griggs, D. & Raleigh, C. The Denver earthquakes. Science 161, 1301–1310 (1968).
Perfettini, H., Schmittbuhl, J., Rice, J. R. & Cocco, M. Frictional response induced by time-dependent fluctuations of the normal loading. J. Geophys. Res. Solid Earth 106, 13455–13472 (2001).
Häring, M. O., Schanz, U., Ladner, F. & Dyer, B. C. Characterisation of the Basel 1 enhanced geothermal system. Geothermics 37, 469–495 (2008).
Acknowledgements
M.A. was supported by a graduate fellowship from Saudi Aramco. R.J. acknowledges funding from ExxonMobil through its membership in the MIT Energy Initiative.
Author information
Authors and Affiliations
Contributions
R.J. designed research; M.A. performed research; M.A. and R.J. analyzed results; and M.A. and R.J. wrote the paper.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Peer review information Nature Communications thanks Matthew Weingarten and the other, anonymous, reviewer(s) for their contribution to the peer review of this work. Peer review reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Alghannam, M., Juanes, R. Understanding rate effects in injection-induced earthquakes. Nat Commun 11, 3053 (2020). https://doi.org/10.1038/s41467-020-16860-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-020-16860-y
- Springer Nature Limited
This article is cited by
-
Effects of Fluid Pressure Development on Hydrothermal Mineralization via Cellular Automaton Simulation
Mathematical Geosciences (2024)
-
Direct Comparison of Numerical Simulations and Experiments of \(\hbox {CO}_2\) Injection and Migration in Geologic Media: Value of Local Data and Forecasting Capability
Transport in Porous Media (2024)
-
The Impact of Size-Dependent and Stress-Dependent Fracture Properties on the Biot and Skempton Coefficients of Fractured Rocks
Rock Mechanics and Rock Engineering (2024)
-
Stress transfer outpaces injection-induced aseismic slip and triggers seismicity
Scientific Reports (2023)
-
The physical mechanisms of induced earthquakes
Nature Reviews Earth & Environment (2023)