Abstract
A Pb-based synthetic mineral referred to as psimythion (pl. psimythia) was manufactured in the Greek world at least since the 6th c BCE and routinely by the 4th c BCE. Theophrastus (On Stones, 56) describes its preparation from metallic Pb suspended over a fermenting liquid. Psimythion is considered the precursor of one of western art’s most prominent white pigments, i.e. lead white (basic lead carbonate or synthetic hydrocerussite). However, so far, and for that early period, published analyses of psimythia suggest that they consisted primarily of synthetic cerussite. In this paper, we set out to investigate how it was possible to manufacture pure cerussite, to the near exclusion of other phases. We examined the chemical and mineralogical composition (pXRF/XRD) of a small number of psimythion pellets found within ceramic pots (pyxis) from Athens and Boeotia (5th–4th c BCE) in the collection of the National Archaeological Museum (NAM), Athens. Analyses showed that the NAM pellets consisted primarily of Pb/cerussite with small amounts of Ca (some samples) and a host of metallic trace elements. We highlight the reference in the Theophrastus text to ‘spoiled wine’ (oxos), rather than ‘vinegar’, as has been previously assumed, the former including a strong biotic component. We carried out DNA sequencing of the pellets in an attempt to establish presence of microorganisms (Acetic Acid Bacteria). None was found. Subsequently, and as a working hypothesis, we propose a series of (biotic/abiotic) reactions which were likely to have taken place in the liquid and vapour phases and on the metal surface. The hypothesis aims to demonstrate that CO2 would be microbially induced and would increase, as a function of time, resulting in cerussite forming over and above hydrocerussite/other Pb-rich phases. Psimythion has for long been valued as a white pigment. What has perhaps been not adequately appreciated is the depth of empirical understanding from the part of psimythion manufacturers of the reactions between abiotic and biotic components within ‘oxos’/pot, as key drivers of minerals synthesis. Ultimately, psimythion manufacture may rest in understanding the nature of ‘oxos’, antiquity’s relatively little researched strongest acid.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Psimythion: the sources
There is substantial evidence in the literary record of the Greek world of the 5th–3rd c BCE to suggest that women of all ages and across social boundaries applied a white powder, psimythion, as a cosmetic and for purposes of beautification. So extensive was its apparent use that religious temples felt obliged to list it amongst the items that women were not allowed to wear on entering their premises and/or participating in the activities within (Tsoucaris et al. 2011). For example, at the sanctuary of Andania in the Peloponnese (1st c CE), the wearing of psimythion was banned together with gold jewellery and red dye (IG5(1).1390.22).
The desire to have and/or maintain a fair skin appears to have run deeply within Greek culture, as one can gauge from the Homeric poems. The adjective λευκώλενος (white-armed) is associated mostly with the goddess Hera (for example Homer Iliad, 8.484) but also with mortal women like Andromache, Hector’s wife, or Penelope, Odysseus’ wife, or Helen of Troy and in association with purely female attributes (for example submissiveness, vulnerability, desirability). If a fair skin was indeed a social requisite, for women who did not have it, artificial substances must have been the only remedy.
There is no suggestion that the Homeric ladies used psimythion but it follows that, for later periods, psimythion must have filled that gap in market demand: ‘Has anyone a dark complexion, white-lead will that correct,’ Athenaeus (Deipnosophistai, xiii.23) notes as late as the 3rd c CE. Before its use as a cosmetic, it is perhaps its ‘whiteness’ that forms the focal point of its attributes as can be gleaned from the earliest reference to psimythion, a fragment of Xenophanes (6th–5th c BCE) (Fragment 28,978a, line 10) and indeed in later texts by Aristotle (Nicomacheian Ethics 1096b, line 23).
Nevertheless, the wearing of psimythion came at a price since it could also be a cause of ridicule, particularly by comic poets like Aristophanes, who appears to have had a particular dislike for the substance and/or the women who wore it: Are you an ape plastered with white lead, or the ghost of some old hag returned from the dark borderlands of death? (Aristophanes Eccleciazousae 1072). It was thought as a means for females to conceal their age: ‘No, no! as she is there, she can still deceive; but if this white-lead is washed off her wrinkles will come out plainly (Aristophanes Plutos 1065).
Furthermore, it appears that one way to discredit an Athenian lady’s reputation for being virtuous was to allude to her wearing psimythion, …. at the wrong time(!): ‘But it struck me, sirs, that she had powdered her face though her brother had died not thirty days before; even so, however, I made no remark on the fact, but left the house in silence’ (Lysias, On the murder of Eratosthenes 1.14). Men applying psimythion on themselves appears to have been frowned upon: ‘she adorned his (Alciviades) face like a woman’s with paints and pigments’ (Plutarch Alcibiades 39.2). The use of psimythion by males is also attested by Ctesias, a 5th c BCE Greek physician (Fragment 1b line 689). By the Roman period, the use of cerussa (Latin for psimythion) seems to have been more widely accepted, yet old beliefs die hard: ‘You dye your head but you will never disguise your old age nor straighten out the wrinkles in your cheeks. Don’t cover your face with paint so as to have a mask and not a face. For it avails nothing. Why are you so foolish? Paint and dye won’t make Hecuba a Helen’ (Lucilius Epigram Book II).
It is perhaps its entry to the Hippocratic Corpus of the 5th–4th c BCE that alerts us to its properties beyond the aesthetic. Psimythion was used for external applications. It was dispensed for eye ailments with spodium, saffron and myrrh (Epidemics 2, 5.22.2); for ear discharge, with sandarah and ‘flower of silver’ (De Morbis 2, 14.18); for ulcers, mixed with olive oil, resin, pine bark and animal fat (De Ulceribus 21.4). Also for gynaecological applications as a suppository, on a piece of wool soaked with water (De Natura Mulierbi 29–5). Finally, as an emplastron (plaster/wound dressing) and in association with other ‘metallics’ (misy, gold scoria, roasted copper (De Mulieribus Affectibus 103, 5–9). Another medical author, Diocles (4th c BCE), includes it in a recipe for eye ailments together with another ‘metallics’ like pompholyx (Fragment 147 line 4).
Psimythion: the material culture
Lead- and copper-based minerals can be traced in Egypt in the 2nd millennium BCE (Walter et al. 1999) and in the Royal Tombs of Ur in the 3rd millennium BCE (Hauptmann et al. 2016). The Theophrastus recipe for psimythion making, but also other synthetic minerals, like the copper-based ios xystos (Theophrastus, On Stones, 57), puts synthetic mineral manufacture at centre-stage in the Classical/Hellenistic world. Use of psimythion in contemporary art (5th c BCE) is attested only occasionally. It was identified in a single ‘brush stroke’ (‘Pheidias’ brush stroke’) on the pediment of the Parthenon of Athens consisting of hydrocerussite mixed with gypsum and a phosphate mineral (Jenkins and Middleton 1988, 204). More visible are the applications of hydrocerussite in the Hellenistic world, including 4th–3rd c BCE funerary paintings from Macedonia (Brecoulaki et al. 2014) and as an undercoat to organic pigments. At the opposite end of the chronological spectrum, there is evidence for its production, in the Early Bronze Age, at Akrotiri, Thera (Sotiropoulou et al. 2010). Recently, researchers have shown that cerussite had been applied on Early Cycladic marble figurines as a white substrate on the areas of the marble that would be eventually decorated, and prior to the application of the coloured pigment. They suggested that it was the cerussite, rather than the colourful pigments themselves, which may have been responsible for the preservation of anatomical and other details, often described as ‘paint ghosts’ (K Manteli, pers. comm.).
On the other hand, psimythia, in pellet or lump form, have been found within lidded ceramic vessels, in (primarily) female burials. However, such finds tend to be rather rare, when viewed in the context of the vast number of excavated female burials. A number of these pellets have already been analysed, albeit not with the same methods (Table 1). Of the 12 samples, 3 are pink coloured (Eretria, Kerameikos and Delphi) and therefore mixtures: one is cerussite mixed with iron oxide (Eretria), the second, ‘PbO’ (no cerussite/hydrocerussite is mentioned) mixed with HgS (Delphi) and the third, cerussite with HgS ( Kerameikos). Of the remaining 9 samples, 3 are primarily hydrocerussite with small amounts of cerussite (Volos 396 and 471; Agora, Athens). Of the remaining 6, 5 are 100% cerussite (Corinth, Volos 439, Eleusis, Paestum, Kerameikos) and 1 is primarily cerussite with some hydrocerussite (Derveni). Interestingly, the Kerameikos psimythion was found not within a female burial, but rather within that of a male actor; the latter were highly likely to make use of the powder, since males would take on female roles (Kapparis 2018).
The analyses of the artefacts in Table 1, by different researchers and over the last 80 years, suggest that 6 out of the 9 white samples contain cerussite over and above hydrocerussite and/or other phases. The above data set is not large and, as such, conclusions drawn are more likely to be indicative, rather than definitive. Nevertheless, the question arises as to which parameter(s) control the production of cerussite, above other phases, within the Theophrastus pot. It is the excess of CO2 and maintenance thereof throughout the 10-day cycle that would have ensured the production of cerussite in preference to the hydrocerussite. This paper sets out to present a working hypothesis regarding the importance of the biotic component within the oxos as a driver of CO2 production. The two sections that follow assess past reconstructions of the Theophrastus pot (‘Oxos in the Theophrastus recipe: Pb metal in the presence of fermenting liquid’ section) and recent (‘Vinegar in Pb corrosion studies’ section) work on Pb metal corrosion led by acetic acid bacteria (AAB) and other microorganisms.
Oxos in the Theophrastus recipe: Pb metal in the presence of fermenting liquid
Theophrastus’ (On Stones, 56) recipe for psimythion making reads as follows: ‘lead (molybdos) about the size of a brick is placed in jars (pithos) over vinegar (oxos) and when this acquires a thick mass, which it generally does in ten days, then the jars are opened and a kind of mold (evros) is scraped off the lead, and this is done again until it is all used up. The part that is scraped off is ground in a mortar and decanted frequently, and what is finally left at the bottom is white lead (psimythion)’ (Caley and Richards 1956, 188) (the transliterated Greek in parentheses is our addition.)
There have been many attempts to reproduce psimythion experimentally and in the manner of the Theophrastus set-up. Katsaros et al. (2010) reproduced this recipe in a similar pot, a pithos, resulting in the production of hydrocerussite and cerussite. When the authors analysed psimythion pellets from the Kerameikos cemetery (see Table 1), they found them to consist primarily of cerussite.
Principe (2018) carried out experiments similar to that of Katsaros et al. (2010) but in a glass jar. He did not report any mineralogical analysis of his finds, so it is not clear what exactly he made, cerussite or hydrocerussite or lead acetate. Regarding the question of the source of the CO2, he suggests that the diurnal effect, i.e. the temperature variations between day and night, would have had an effect on the O2/CO2 introduced into the poorly sealed vessel of coarse fabric every night (‘a daily cycle of breathing’) as a result of vinegar vapour contraction. CO2 may indeed have been made available in that way but the question is whether it would be sufficient to generate enough hydrocerussite/cerussite over a 10-day cycle. We argue in favour of a more reliable and continuous source of CO2, i.e. that which can be generated within a fermenting liquid by either aerobic (acetic acid) bacteria converting acetic acid to CO2 and water and/or facultative anaerobic yeasts (Saccharomyces) doing the same.
We have introduced the presence of the microorganisms because Theophrastus makes reference to the use of ‘oxos’. Within a 5th–3rd c BCE context, oxos would have been translated as ‘poor wine or vin ordinaire’ or ‘vinegar produced from oxos’ (see entry in Liddell Scott Dictionary—www.perseus.tufts.edu). In the second meaning, it is made clear that vinegar is distinct from and not synonymous with oxos. Xenophon in his Anabasis (2.3.14) refers to oxos produced from ‘boiling’ (fermenting) palm wine. The issue of fermentation, both implied and stated by these authors, suggests that the biotic component plays a key role and needs to be brought forward in any psimythion-related discussion.
In the past, a number of researchers had queried whether the Theophrastus arrangement could actually produce anything other than lead acetate, the result of acetic acid vapour reacting with lead metal (Bailey 1932; Shear 1936; Stevenson 1955). Since lead acetate, as a water-soluble salt, would have never worked as a cosmetic or an artist’s pigment, it follows that there must have been an obvious source of CO2 helping to convert lead acetate to lead carbonate.
In an attempt to tackle the question of the origin of the elusive CO2 source, Caley and Richards (1956, 188) proposed that ‘another source of the carbon dioxide may have been the so-called vinegar used in the process. If this was merely a spoiled grape juice undergoing both alcoholic and acetous fermentation, ample carbon dioxide would have been available’.
Grape skin hosts a number of aerobic (acetic acid bacteria (AAB)), facultative anaerobic (e.g. yeasts, like Saccharomyces spp.) and anaerobic (e.g. Acetobacterium spp.) microorganisms which play key roles in the conversion of sugars to alcohol and alcohol to vinegar. Mortimer and Polsinelli (1999) have demonstrated that one of them, Saccharomyces cerevisiae, constitutes about one-quarter of the totality of yeasts living on damaged grape skin (grapes that have been pressed and squeezed). Cavalieri et al. (2002) identified the same microorganism in the lees residue within a wine jar dated to the 4th millennium BCE from Egypt. The authors have suggested that this yeast served as an inoculum for bread and beer. Although yeasts are responsible for the transformation of grape juice to wine they are also capable of spoiling it. S. cerevisiae is the yeast primarily responsible for spoilage since it can resist high alcohol concentrations and low pH (Martorell et al. 2005).
Vinegar in Pb corrosion studies
In their study on the crystal growth of lead carbonates under different media, Sánchez-Navas et al. (2013) reproduced the ‘stack’ or ‘Dutch’ process where metallic lead was first oxidized by acetic acid vapours in the presence of moisture, and the resulting lead acetate was later transformed into basic lead carbonate (hydrocerussite) by the action of carbon dioxide (Gettens et al. 1967). The ‘stack’ process used the same raw materials, i.e. lead metal exposed to acetic acid vapours, but not in a closed pot, as in the Theophrastus case. The source of the CO2, in this case, was manure which surrounded the stacked pots of lead/acetic acid.
Sánchez-Navas et al. (2013) used various sources of CO2, one of them being a liquid culture of Acetobacter sp., or acetic acid bacteria (AABs) which can make acetic acid from alcohol but can also oxidize acetic acid for the production of CO2 and H2O. They considered this a bio-mediated process and noted that if nitrogenated organic matter is present (for example proteins), then not only CO2 but also NH3 is produced. Ammonia (in the gas phase) would increase the pH on the metal plate favouring, they argued, the formation of hydrocerussite. They also noted that, in the course of their reactions, the product formed was poorly crystalline hydrocerussite/cerussite at atmospheric partial pressures of CO2 (10–3.5 atm) but when a higher CO2 pressure was used (1 atm) by flowing gas in the container, cerrusite was formed. This is consistent with the higher carbonate content of cerussite, where 1 mol of Pb requires 1 mol CO2, compared with 0.67 mol of CO2 required per mole of Pb to form hydrocerussite.
More recently, Gonzáles et al. (2019b) also reported that a CO2 producer is necessary to quickly form lead carbonates. They showed that the metal surface can have many layers of product consisting of plumbonacrite (Pb5(CO3)3O(OH)2) at the lead surface followed by outer layers of hydrocerussite Pb3(CO3)2(OH)2 and cerussite (PbCO3) which are in direct contact with each other. The role of CO2, heat and UV light in the production of cerussite deserves further study. They noted that using vinegar as the source of acetic acid, and with no separate CO2 source beyond atmospheric CO2, no hydrocerussite or cerrusite is produced, even after 1 month; yet Katsaros et al. (2010), by placing lead over vinegar in a jar sealed but with a breathable leather lid, formed hydrocerussite and cerussite after 10 days. Both systems had access to atmospheric CO2 and O2, the main difference being that Katsaros et al. heated their sample container (27–55 °C) by placing it outside ‘in the sun’, followed by washing and drying the sample outside in sunlight. Washing removes soluble acetates which do not convert on heating to carbonates (Martínez-Casado et al. 2016) but whether heating/sunlight converts plumbonacrite to cerussite is unknown. Finally, Gonzáles et al. (2019b)) addressed the question of hydrocerussite stability in air and reported no evidence at all of cerrusite formation after hydrocerrusite was exposed to laboratory air for 26 months; it is therefore unlikely that the cerussite analysed here was formed during burial.
This paper is divided in two parts. In the first part, we investigate a select number of complete and fragmented pellets of psimythion, in the collection of NAM (‘The NAM pellets’ section and Fig. 1), on the basis of their composition, as well as metrology (‘The NAM pellet metrology’ section, Fig. 2, Table 2). The pellets appear to have been ‘cast’ in moulds and therefore it is possible to arrive at the shape of the latter by looking closely at the shape of the former (Fig. 3). The ‘Method’ section outlines the method of their examination while the ‘Results’ section gives a description of the results. Chemically the pellets are made of Pb with Ca as a minor element (‘pXRF analyses of multiple fragments’ section and Tables 3 and 4). Mineralogically they are made primarily of cerussite (‘XRD and SEM-EDAX analysis’ section and Table 5 and Fig. 4a). In hypothesising a mechanism by which cerussite could be produced to the near exclusion of other phases, we focus on the biotic element within the ‘oxos’, as a key driver in CO2 production within the closed Theophrastus pot. For a full discussion, see the ‘CO2 -rich conditions prevailing within the Theophrastus pot: a hypothesis’ section.
The NAM pellets
Complete and fragmented pellets of psimythion, deriving from the contents of two pyxides, lidded ceramic vessels, NAM 13676a and NAM 13676b (Fig. 1a) were retrieved from burials dating to the 5th–4th c BCE, Athens; also ‘loose’ (without a pyxis) complete and fragmented pieces of psimythion (Fig. 1d) from a cemetery at Tanagra, Boeotia, c. 60 km north of Athens. The pyxis (NAM 11447), with which the latter are currently displayed, is from Rhodes. These pyxis-less pellets from Tanagra are also dated to the 5th–4th c BCE.
NAM 13676a (Fig. 1b)
Pyxis with lid found together with pyxis B, 136763b, in the foundations of a house in a plot opposite the National Technical University, Patission Street, Athens, in the late 1890s. On the body of the pyxis (Fig. 1b) is a depiction of women’s quarters, while on the lid, a band of egg-and-dot patterns surrounds a wreath of ivy leaves. The pyxis is attributed to the Painter of Athens 1585 and is dated 410–400 BCE. The 13676a collection consists of three complete pieces, one near-complete and 22 fragmented ones, a total of 26.
NAM 13676b (Fig. 1c)
Miniature pyxis with lid found together with pyxis A, 136763a above. On the body is a depiction of a hare, a feline and swans, while on the lid, there are three female heads alternating with anthemia surrounded by a band of egg-and-dot pattern. It is also dated 410–400 BCE. Its contents include two complete pieces, two near complete and numerous fragmentary ones.
NAM 11332 (Fig. 1d)
Thirty-six white pellets from Tanagra, Boeotia: 14 of them are complete, 14 are near complete and eight are fragmentary. Figure 1d displays 19 of the 36. They are dated, by association, to the end of the 5th–end of 4th c BCE based on the chronology of the tombs in the Tanagra cemetery.
Method
pXRF
pXRF analyses took place at the National Archaeological Museum, Athens, with a NitonX3Lt-GOLDD instrument which has a 50kVAgX-raytube, 80-MHz real-time digital signal processing and two processors for computation and data storage respectively. The TestAllGeo (TAG) mode was selected. Analysis time was set at 60 s and two measurements were taken on different spots on each fragment. An average of the two is shown here. Replicate analyses of NIST SRM 2709a soil standard revealed satisfactory precision (< 10% Zr and < 5% Rb and Sr), good accuracy for Sr (< 10%), but poor accuracy for Zr and Rb which were underestimated by over 90%, based on using NIST 2709a as the internal standard. However, the above elements are not crucial to the discussion here. The two elements of relevance here were Pb and Ca. Therefore, four external standards were prepared using reagent grade PbO and CaCO3. Results are shown in Table 3.
SEM-EDAX
A tungsten filament Scanning Electron Microscope (W-SEM) HITACHI S-3700, combined with an Oxford Inca 350 with 80-mm X-Max detector, based at University of Strathclyde’s Advanced Materials Research Laboratory, was used for the elemental analysis of materials. Freshly fractured surfaces of specimens were gold -coated.
XRD
Fragments of psimythion pellets were analysed using X-ray diffraction (Bruker D8 Advance) with a Cu Kα X-ray source. To determine the cerussite to hydrocerussite ratios within the analysed replicates, we performed quantitative Rietveld refinements on the XRD patterns using TOPAS and the crystallographic information files for cerussite (Antao and Hassan 2009) and hydrocerussite (Martinetto et al. 2002).The subsamples from NAM 11332, NAM 13676a and NAM 13676b consisted respectively of powdered psimythion only, both powdered and a single fragment of a psimythion pellet and two fragments of one (or two) psimythion pellet(s).
DNA Analyses
Given the presence and crucial role that microorganisms play in the reactions to be outlined below, it was desirable to find potential DNA signatures of the microorganisms within the samples. DNA half-life has been determined to be over 500 years (Allentoft et al. 2012), but, buried in soils, it can last 1000–10,000 years (Thomsen and Willerslev 2015). DNA were extracted from approximately 100 μg of mineral material in triplicate using a Qiagen DNAeasy Soil extraction kit. DNA quantity and extraction purity were screened using UV-microspectrometry (Epoch BioTek; Swindon, UK). Final extracts were further diluted 1/10 and 1/100 to be included in downstream processes along with the ‘neat’ (undiluted) extracts. Dilution of samples has often been applied in cases where enzyme-inhibiting materials (e.g. chlorophyll, metals or humic acids) could possibly exist. Here, the likelihood of Pb+2 posed a concern, although the extraction method does involve the precipitation removal of cationic elements.
Assays for the detection of Saccharomyces fungus and Acetobacter involved sensitive quantitative polymerase chain reactions (qPCR). Primers were based on those previously reported: Saccharomyces sp. (SFC1 forward primer: 5′ GGACTCTGGACATGCAAGAT and SCR1 reverse primer: 5′ ATACCCTTCTTAACACCTGGC; Salinas et al. 2009) and two sets of Acetobacter sp. primers: (forward #1: GCTGGCGGCATGCTTAACACAT and reverse #1: GGAGGTGATCCAGCCGCAGGT; forward #2: TCAAGTCCTCATGGCCCTTATG and reverse #2: TACACACGTGCTACAATGGCG (González et al. 2005). qPCR conditions involved 10-μL reactions (5 μL GoTaq® qPCR Master Mix; Promega (Madison, WI, USA)) with 40 cycles of thermal cycling: 95 °C for 10 s (DNA denaturation), 60 °C for 20 s (primer annealing and elongation), on a BioRad iCycler (BioRad; Hercules, CA, USA). Genomic DNA from previously identified cultures were used as positive controls; molecular-grade water was used as a negative control.
Results
The NAM pellet metrology
Twelve pellets from Tanagra, Beoetia (11332) and three pellets from Athens (13676a) showed surprising homogeneity with a mean diameter of 2.8 cm, thickness of 0.8 cm and a weight of 7 g and with a uniform standard deviation of c. 15%. Interestingly, our data is in good agreement with those of Katsaros et al. (2010) who measured pellets from the Kerameikos. They report diameter = 2.75 cm, thickness = 0.6 cm and weight = 5.5 g suggesting that the psimythion industry of the period operated on an accepted ‘standard’ of weights and measures (Table 2).
The shape of the pellets varies and as long as the dimensions and weights are kept constant, it is possible to make allowances for ‘preferred’ shapes by different workshops. The Tanagra pieces vary as follows: 11332-3 (Fig. 2a) is flat on both sides, while Fig. 2b and c show pellets with only one side concave and the other flat. The Athens pellets had a shallow convex/concave surface, with the concave surface facing up (Fig. 2e—right) and the convex surface in the opposite direction (Fig. 2e—left); similarly for those in Fig. 2d and f. The different cross-sections displayed by the pellets suggest that each workshop may have had its own preferred shape(s), but all were required to abide by prescribed dimensions and weight.
The uniform shape and size of the NAM pellets suggest that they may have been formed within a bivalve mould, as shown in Fig. 3, the top part closing on the bottom in the manner shown here: the concave surface facing down and adhering onto the bottom section of the mould, and the convex adhering to the top part. The mould may have been made of carved wood or ceramic given the smooth surface of all pellets. The mould may have been covered by a medium, perhaps calcium-rich, preventing the adherence of the pellet on the mould and allowing each pellet to detach easily. The space left by an air bubble trapped between the surface of psimythion and the bottom section of the mould can be seen in Fig. 2d.
pXRF analyses of multiple fragments
Non-destructive pXRF analysis was carried out on a number of samples, at the NAM, both complete and fragmented (Tables 3 and 4). In total, c. 9 pellets of sample 13676b and 9 pellets of sample 11332 were analysed on both their flat and curved faces. The results were calibrated against prepared standards (PbO-CaCO3) for only two elements Pb and Ca (Table 3) which showed values above 0.5%. The 13676b samples contained c. 82% Pb and 2% Ca by weight on their flat face; and c. 70% Pb and 2.5% Ca on their curved faces. Ca values for the 11332 samples were low and there was no variation between the curved and the flat face. Table 4 shows uncalibrated data sets for same sample sets and with regard to Cu, Sn, Sb, Cd and Ag.
XRD and SEM-EDAX analysis
Permit was granted to take one fragmented pellet from each of the three pyxides 13676a and 13676b and 11332 and subject it to destructive analysis via SEM-EDAX and XRD.
SEM-EDAX image and analysis (Fig. 4b) of the surface of a fragment of a pellet from 11332b showed large well-formed cerussite crystals with composition corresponding to c. 70% Pb, 15% O and 15% C; the results are uncalibrated but definitely point to cerussite. For XRD analysis, a number of samples were obtained. In the case of the pellet from pyxis, 13676a, powder samples were taken from both surfaces, the convex and concave. A section of that pellet was subsequently crushed and ground and mounted for XRD analysis. Similarly for pellets from pyxides 13676b and 11332. The XRD patterns for all are shown in Fig. 4a and the quantitative assessment in weight per cent of each is given in Table 5. Only two minerals are identified, namely cerussite and hydrocerussite. It is noted that the powder scraped off the concave surface has a slightly higher concentration of hydrocerussite as opposed to powder scraped off the convex surface. In one case, the hydrocessurite of that concave face is c. 11%. When the powder subsample is obtained following pulverisation of the original, then the hydrocerussite concentration is c. 2%.
Summary
The entire collection of NAM psimythia consists of 103 pieces, in complete or mostly fragmentary state. XRD analysis of three pellets (various fractions) shows cerussite with hydrocerussite not exceeding c. 11%. Ca has been detected in the pXRF but was not visible in the XRD of the samples analysed here and as part of a distinct phase. From the perspective of trace elements, there are elevated amounts of Ag which may point to an Ag-rich Pb metal source, Laurion in Attica being the most likely candidate for the manufacture of such metal (Photos-Jones and Jones 1994).
DNA extraction and qPCR of some pellets
Community DNA was extracted from three pellets. Visually, the material had minimal evidence of organic matter, and determinations of DNA concentrations were found below detection (< 2 ng/μL) and without any evidence of impurities. The lack of DNA evidence does not suffice to preclude the qPCR analysis, as the assay is innately more sensitive (detection limit: 100 DNA copies/g). However, the samples were negative (positive assays showed results > 95% efficiency of reactions). As such, Saccharomyces or Acetobacter were absent in all pellets. This suggests that reactions on the metal-mineral phase are likely abiotic, but it may be that the effect on the composition of gases within the pot may have been largely microbially mediated.
CO2-rich conditions prevailing within the Theophrastus pot: a hypothesis
Theophrastus describes psimythion manufacture as consisting of two stages: (a) the preparation of synthetic cerussite and (b) at the beneficiation thereof by grinding, dissolving and decanting of the soluble components with the aim of their enrichment and refinement with regard to both composition and particle size. The need to grind the flakes of psimythion into fine powder, its subsequent mixing with water allowing for any soluble matter to dissolve, the settling of the insoluble parts and the decanting of the soluble ones, all of the above steps would have aimed at producing a pure final product.
Our proposed model for the reactions taking place within the Theophrastus pot is illustrated in Fig. 5. The prescribed 10-day cycle has been divided notionally into three stages to account for reactions taking place at different times and ‘fronts’. These stages are not sharply divided but rather merge into one another and can also be reversible, if conditions within the pot change. First, there are reactions between the metal (lead) surface and the gaseous phase (i.e. the air space above the liquid). Second, there are reactions taking place within the oxos. The biotic component is made up of microorganisms, both aerobic (acetic acid bacteria (AAB)/Acetobacter) and anaerobic (yeast/Acetobacterium and other obligate bacterial fermenters) actively changing the chemistry of the oxos. These changes result in changes in the gas phase, via the production of O2/CO2/acetic acid vapour, which in turn have a direct effect on the reactions on the metal surface.
In stage 1, aerobes (AAB and Acetobacter) are active in an oxygen-rich environment converting alcohol to acetic acid. But the same bacteria also respire aerobically converting acetic acid to CO2 and water. Although at the start the gas phase in the pot is O2 rich, under the dual action of the aerobes (oxidation of alcohol and respiration/metabolic activity), it becomes increasingly richer in CO2, acetic acid and water vapour. On the metal surface, a reaction between Pb (metal), O2 and water vapour results in the formation of lead hydroxide; this, in turn reacts with a vapour that is an increasingly rich in acetic acid, forming lead acetate.
Stages 1 and 2 form a continuum, in the sense that there is no abrupt end to stage 1 before stage 2 begins. The reactions on the Pb metal surface continue to produce lead hydroxide (or lead oxide) and acetate; given the increased levels of CO2 (due to the microbial respiration/metabolic activity), hydrocerussite and acetic acid are formed during stage 2. At the end of stage 1, O2 levels have depleted due to microbial consumption and the formation of lead hydroxide stops. During stage 2, anaerobic microbes are (re)activated in the bottom of the pithos and due to the depletion of O2, they will be active throughout the pithos during stage 3. In stage 3, the reactivation of the anaerobes within oxos leads to the formation of additional levels of CO2 due to the anaerobic respiration/metabolic activity by microbes converting acetic acid into CO2 and H2O. During the depletion of lead hydroxide (through the formation of hydrocerussite) and the increase in the levels of CO2, cerussite is formed at the expense of hydrocerussite. We should note, however, that we cannot rule out or confirm the formation of hydrocerussite via plumbonacrite, as an intermediate phase, as observed by Gonzáles et al. (2019a) during the Dutch process.
Figure 6 gives an illustrative summary of the trend in gas and solid phase composition for stages 1–3 as described in Fig. 5. Stage 1 is characterized by a slow decrease in O2, rapid increase in acetic acid vapour and gradual increase in CO2. Lead hydroxide and lead acetate form on the lead metal surface. During stage 2, there is a levelling in the amount of acetic acid vapour, together with a sharp decrease in O2 and a continuing increase in CO2. On the metal surface, lead hydroxide gets depleted as hydrocerussite forms rapidly followed by an initially slow rise in lead carbonate. Finally, in stage 3, acetic acid vapour is gradually depleted, while CO2 levels continue to rise leading to the preferential formation of lead carbonate (cerussite), rather than basic lead carbonate (hydrocerussite) on the ‘corroded’ lead metal surface.
Conclusions
The manufacture of a white lead-based pigment has had a long history, recorded in detail, at least since the 4th c BCE. Given the commonality of its raw materials, i.e. lead metal and oxos, the simplicity of the installations and the relatively hands-off nature of the process, there has been a broad, albeit expressly unstated, assumption that from antiquity to the modern era ‘one recipe’ fitted all. This is not true and earlier researchers took pains to recognize and report on the many variations within that long time-span, not simply chronologically, but also regionally (Pulsifer 1888, 196). We suggest that during that time-depth ‘different’ white lead-based minerals were produced and each period may have developed its own recipes and working conditions. Mass production of this white pigment continued well into the modern times via the stack/Dutch process (Gettens et al. 1967). We argue that present archaeological evidence suggests that, for the period of concern here, synthetic cerussite was the main mineral intended to be produced. The question is how was this achieved.
The proposed hypothesis for the conditions prevailing within the Theophrastus pot is that they are dynamic and not static throughout the 10-day cycle. Active (and inactive) microbial communities within the oxos control the composition of the gas phase and in turn are controlled by it. This dynamic state must have been well understood by the psimythion makers. Any disturbance thereof, even a mere opening of the lid at any stage in the 10-day cycle to ‘check progress’, or indeed any interruption of the process somewhere between stages 2 and 3 (with subsequent introduction of O2) would alter the dynamics and probably push towards the production of the hydrocerussite, at the expense of cerussite. The above consistent ‘push’ of the equilibrium towards cerussite combined with the standardisation of the pellet form, shape and weight (see the ‘The NAM pellet metrology’ section) suggests an industry well on top of its own practice.
Returning to the NAM artefacts and our search for saccharomyces and acetobacter, as already mentioned, no such microorganisms were found. The two genera are most commonly associated with the suggested processes, but possibly not exclusively so. Their absence may be due to the concentrations of extracted DNA being practically ‘nil’.
Psimythion has for long been valued as an important white pigment in art and in cosmetics. In the period concerned here, it was also used as a mineral constituent of various medicines. Studying the material culture of the past on the basis of its use alone is only one way of looking at it and as such, it is usually limiting. It leaves unexplored other areas, ranging from aspects of its manufacture to its perceived value and symbolism (if any) within the cultural framework that generated it. In the case of psimythion, what is perhaps most intriguing is the implicit empirical understanding, from the part of psimythion manufacturers, not only of the range and dynamics of the chemical reactions, both biotic and abiotic, taking place within the pot, but also of their ability to control them. ‘Oxos’, its composition and properties, holds centre-stage and a better understanding of its role in early chemical synthesis of lead- and copper-based minerals is perhaps timely.
Change history
22 October 2020
The original version of this article, unfortunately, contained errors. Author���s correction in Table 1 changing ���Pb (elemental) with Cinnabar��� was misinterpreted as ���PbO���only, when it should have been ������`Pb` with cinnabar���.
References
Allentoft ME, Collins M, Harker D, Haile J, Oskam CL, Hale ML, Campos PF, Samaniego JA, Gilbert MTP, Willerslev E, Zhang G, Scofield RP, Holdaway RN, Bunce M (2012) The half-life of DNA in bone: measuring decay kinetics in 158 dated fossils. Proc R Soc B 279:4724–4733. https://doi.org/10.1098/rspb.2012.1745
Antao SM, Hassan I (2009) The orthorhombic structure of CaCO3, SrCO3, PbCO3 and BaCO3: linear structural trends. Can Mineral 47:1245–1255
Bailey J (1932) Elder Pliny’s chapters on chemical subjects, part II. Arnold, London
Brecoulaki HS, Sotiropoulou S, Katsifas C, Karydas AG, Kantarelou V (2014) A microcosm of colour and shine. The Polychromy of Chryselephantine Couches from Ancient Macedonia Thérapéia Polychromie et restauration de la sculpture dans l’Antiquité Te c h n è 4: 9–21
Caley ER (1945) Ancient Greek pigments from the agora. Hesperia 14(2):152–156
Caley E, Richards J (1956) Theophrastus on stones. Ohio Univ, Press
Cavalieri D, McGovern PE, Hartl DL, Mortimer R, Polsinelli (2002) Evidence for S. cerevisiae fermentation in ancient wine. J Mol Evol 57:S226–S232. https://doi.org/10.1007/s00239-003-0031-2
Gettens RJ, Kühn H, Chase WT (1967) Lead white. Stud Conserv 12(4):125–139
Gonzáles V, Cotte M, Wallez G, van Loon A, de Nolf W, Eveno M, Keune K, Noble P, Dik J (2019a) Identification of unusual plumbonacrite in Rembrandt’s impasto by using multimodal synchrotron X-ray diffraction spectroscopy. Ang Chem Int 58:5619–5622. https://doi.org/10.1002/anie.201813105
Gonzáles V, Walleza G, Calligaro T, Gourier D, Menu M (2019b) Synthesizing lead white pigments by lead corrosion: new insights into the ancient manufacturing processes. Corros Sci 146:10–17
González A, Hierro N, Poblet M, Mas A, Guillamón JM (2005) Enumeration and detection of acetic acid bacteria by real-time PCR and nested PCR. FEMS Microbiol Lett 254:123–128
Hasselin-Rous I, Huguenot C, Gerin D (2017) Offrandes Hellenistiques en miniature: le mobilier d’une tombe d’enfant d’Érétrie conservé au Musée du Louvre. Revue Archéologique 25:58–59
Hauptmann A, Klein S, Zettler R, Baumer U, Dietemann P (2016) On the making and provenancing of pigments from the Early Dynastic Royal Tombs of Ur, Mesopotamia. Metalla 22(1):41–74
Jenkins ID, Middleton AP (1988) Paint on the Parthenon sculptures. Ann Brit Sch Athens 83:183–207
Kapparis KA (2018) Prostitution in the ancient Greek world, De Gruyter
Katsaros T, Liritzis I, Laskaris N (2010) Identification of Theophrastus’ pigments egyptios yanos and psimythion from archaeological excavations: a case study. Archaeosciences (Revue d’Archaeometrie) 34:69–80
Liritzis I, Zacharias N, Papageorgiou I, Tsaroucha A, Palamara E (2018) Characterisation and analyses of museum objects using pXRF: an application from the Delphi Museum, Greece. Studia Antiqua et Archaeologica 24(1):31–50
Martinetto P, Anne M, Dooryhée E, Walter P, Tsoucaris G (2002) Synthetic hydrocerussite, 2PbCO3·Pb(OH)2, by X-ray powder diffraction. Acta Crystallogr C 58(6):182–184
Martínez-Casado FJ, Ramos-Riesco M, Rodríguez-Cheda JA, Cucinotta F, Matesanz E, Miletto I, Gianotti E, Marchese L, Matěj Z (2016) Unraveling the decomposition process of lead(II) acetate: anhydrous polymorphs, hydrates, and byproducts and room temperature phosphorescence. Inorg Chem 55(17):8576–8586. https://doi.org/10.1021/acs.inorgchem.6b01116
Martorell P, Querol A, Fernandez-Espinar MT (2005) Rapid identification and enumeration of Saccharomyces cerevisiae cells in wine by real-time PCR. Appl Environ Microbiol 71(11):6823–6830. https://doi.org/10.1128/AEM.71.11.6823-6830.2005
Mortimer R, Polsinelli M (1999) On the origins of yeast. Res Microbiol 150:199–204
Photos-Jones E, Jones JE (1994) The building and industrial remains at Agrileza, Laurion (fourth century BC) and their contribution to the workings at the site. Ann Brit Sch Athens 89:307–358. https://doi.org/10.1017/S0068245400015446
Principe LM (2018) Texts and practices: the promises and problems of laboratory replication and the chemical explanation of early alchemical processes. In: Nicolaidis E (ed) Greek alchemy from late antiquity to early modernity. Turnhout, Brepols (De Diversis Artibus 104), pp. 159-169
Pulsifer WH (1888) Notes for the history of lead and as an inquiry into the development of the manufacture of white lead and lead oxides D. Van Nostrand, New York
Salinas F, Garrido D, Ganga A, Veliz G, Martínez C (2009) Taqman real-time PCR for the detection and enumeration of Saccharomyces cerevisiae in wine. Food Microbiol 26(3):328–332
Sánchez-Navas A, López-Cruz O, Vidal I (2013) Crystal growth of lead carbonates: influence of the medium and relationship between structure and habit. J Cryst Growth 376:1–10. https://doi.org/10.1016/j.jcrysgro.2013.04.007
Shear L (1936) Psimythion. In: Capps E, Allen JT, Barrett SE (eds) Classical studies presented to Edward Capps on his 70th birthday. Princeton, pp. 314-317
Sotiropoulou S, Perdikatsis V, Apostolaki C, Karydas AG, Devetzi A, Birtacha K (2010) Lead pigments and related tools at Akrotiri, Thera, Greece Provenance and application techniques. JAS 37:1830–1840
Stevenson L (1955) On the meaning of the words cerussa and psimithium. J Hist Med Allied Sci 10(1):109–111
Thomsen PF, Willerslev E (2015) Environmental DNA – an emerging tool in conservation for monitoring past and present biodiversity. Biol Conserv 183:4–18. https://doi.org/10.1016/j.biocon.2014.11.019.za
Tsoucaris G, Walter P, Grammenos D (2011) Cosmetic practices in the ancient Greek world. In: Grammenos D (ed) Macedonia from the 7th century to late antiquity. Zetros, Thessaloniki, pp 319–330 (In Greek)
Walter P, Martinetto P, Tsoucaris G, Bréniaux R, Lefebvre MA, Richard G, Talabot J, Dooryhee E (1999) Making make-up in ancient Egypt. Nature 397:483–484
Welcomme E, Walter P, Van Elslande E, Tsoucaris G (2006) Investigation of white pigments used as make-up during the Greco-Roman period. Appl Phys A Mater Sci Process 83-4:551–556
Acknowledgements
The authors would like to thank the staff at the Advanced Materials Research Laboratory, University of Strathclyde, Glasgow, UK. Also Dr. K Manteli (National Archaeological Museum, Athens) for sharing the information on the analysis of ‘paint ghosts’ on Early Cycladic figurines.
Funding
The work is part of a larger study into Greco–Roman antimicrobial minerals. Principal investigator: E. Photos-Jones. Funding has been provided by Wellcome Trust (Seed Award in the Humanities and Social Sciences (201676/Z/16/Z)).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
The original version of this article was revised: Author’s correction in Table 1 changing “Pb (elemental) with Cinnabar” was misinterpreted as “PbO” only, when it should have been ‘‘`PbO` with cinnabar”.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Photos-Jones, E., Bots, P., Oikonomou, E. et al. On metal and ‘spoiled’ wine: analysing psimythion (synthetic cerussite) pellets (5th–3rd centuries BCE) and hypothesising gas-metal reactions over a fermenting liquid within a Greek pot. Archaeol Anthropol Sci 12, 243 (2020). https://doi.org/10.1007/s12520-020-01184-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12520-020-01184-1