Abstract
Bicarbonate species in the aqueous phase is the primary source for CO2 for the growth of microalgae. The potential of carbon dioxide (CO2) fixation by Chlorella pyrenoidosa in enriched bicarbonate medium was evaluated. In the present study, effects of parameters such as pH, sodium bicarbonate concentration and inoculum size were assessed for the removal of CO2 by C. pyrenoidosa under mixotrophic condition. Central composite design tool from response surface methodology was used to validate statistical methods in order to study the influence of these parameters. The obtained results reveal that the maximum removal of CO2 was attained at pH 8 with sodium bicarbonate concentration of 3.33 g/l, and inoculum size of 30 %. The experimental results were statistically significant with R 2 value of 0.9527 and 0.960 for CO2 removal and accumulation of chlorophyll content, respectively. Among the various interactions, interactive effects between the parameters pH and inoculum size was statistically significant (P < 0.05) for CO2 removal and chlorophyll accumulation. Based on the studies, the application of C. pyrenoidosa as a potential source for carbon dioxide removal at alkaline pH from bicarbonate source is highlighted.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Rapid exploitation of fossil fuels such as coal, petroleum, etc., has invariably increased the concentration of CO2 in the atmosphere to ~400 ppm (Rahaman et al. 2011). Several steps have been taken to control the CO2 emission rates caused during the pre and post-process of various man-made activities. Some of the process includes application of alkanolamine absorbents (Choi et al. 2012; Kim et al. 2013; Pires et al. 2011), desiccant absorption (Stewart and Hessami 2005), adsorption by activated carbon (Lu et al. 2008), mineral carbonate (Wang et al. 2008), zeolite (Wang et al. 2011), molecular sieve, ocean storage (Metz et al. 2005) and geological storage (Holloway 2007). Biofixation of CO2 by microalgae attracted researchers due to its affirmative behavior such as carbon neutral and biomass productivity for its various applications. However, the factors such as economic aspects, life cycle analysis, capital investment and other environment aspects have made these technological impacts slower at commercial level. Unlike other gases, CO2 has some significant limiting factors such as low mass transfer rate, high cost of CO2 capture, its transportation. Meanwhile, when the CO2(g) is passed onto the aqueous solution, it reduces the pH due to the formation of H2CO3 (free CO2) and escapes into the atmosphere thereby resulting in significant CO2 loss during algae culture (Chi et al. 2011). Furthermore, pH is the major determinant of the relative concentrations of the carbonaceous system species in water and could affect the availability of carbon for algal photosynthesis in intensive cultures and at certain situations where the supply of adequate CO2(g) is limited, inorganic carbon sources such as bicarbonate salts (NaHCO3) is best alternative to cultivate microalgae (Hsueh et al. 2009; Lam and Lee 2013; Benemann 1993). Meanwhile, it is also envisaged that mixotrophic mode of cultivating microalgae is best in terms of growth and other applications (Abreu et al. 2012; Bhatnagar et al. 2011; Cheirsilp and Torpee 2012). Based on literature, it can be established that Chlorella sp. is found to be most prominent and efficient in bio-fixing HCO − 3 and can grew well at mixotrophic conditions (Jeong et al. 2003; Lam et al. 2012).
Accordingly, this study has attempted to add to the current knowledge for carbon sequestration by optimizing process parameters for maximum CO2 removal using microalgae in enriched bicarbonate medium. In this context, we aim to discuss the effect of pH, sodium bicarbonate concentration and inoculum size in mixotrophic mode of cultivation for CO2 removal in microalgae. In addition, we have also monitored chlorophyll as indicator for growth and photosynthetic productivity. Also, in order to optimize the chosen factors and its interactions, central composite design (CCD) using response surface methodology has been employed. The application of response surface methodology is to maximize the effective parameters and minimize the experiments as well as to study the variables individual and interactive effects (Wang et al. 2007; Zhang et al. 2009; Khataee and Dehghan 2011).
Materials and methods
Culturing of microalgae
Chlorella pyrenoidosa (NCIM 2738) was obtained from the National Centre of Industrial Microorganism (NCIM), Pune, India and was maintained in BG-11 medium (UTEX 2009) under axenic conditions. The stock solution was prepared for all the constituents in media with the following composition for 100 ml: K2HPO4 0.4 g, CaCl2·2H2O 0.36 g, MgSO4·7H2O 0.75 g, NaNO3 15 g, citric acid 0.06 g, Na2EDTA·2H2O 0.01 g, sodium carbonate 0.2 g, ammonium ferric citrate 0.06 g, and A5 trace solution (g/l) components as H3BO3 2.86, MnCl2 1.81, ZnSO4·7H2O 0.222, Na2MoO4·2H2O 0.390, CuSO4·5H2O 0.079, Co(NO3)2·6H2O 0.0494. From the stock solution the media has been prepared for 500 ml with 5 ml from each constituent and 0.5 ml of A5 trace solution. The culture was subjected to continuous illumination (14 WTL5 tungsten filament lamps; Philips Co.,) with 1500 Lux measured using TES light meter (TES CORP) at room temperature 28 ± 1 °C.
Design of experiments
The exponential phase microalgae cells (28 × 105 cells/ml)were taken for experimental studies in synthetic medium (Feng et al. 2011) with the following composition (g/l) glucose 0.4125, NH4Cl0.078, KH2PO4 0.018, MgSO4·7H2O 0.013, CaCl2·2H2O 0.043, FeSO4·7H2O 0.005, A5 Trace solution (1 ml/l), respectively. All the experiments in the study were carried in 500 ml conical flasks containing 300 ml of working solution of synthetic medium with variables (pH, inoculum size and sodium bicarbonate). For analysis, 10 ml of sample was collected using autoclaved syringe (20 ml) for every 3 days once and was subjected for centrifugation at 8000 RPM for 10 min. The pellet was taken for estimation of chlorophyll and supernatant for CO2 analysis. The pH values were chosen to study the microalgae behavior to CO2 in acidic (pH 4 to mimic more availability of free CO2), pH 6 (as standard growth medium range) and alkaline range (pH 8). The sodium bicarbonate concentrations were fixed of 1–3 g per 300 ml each which was scaled up in g/l as depicted in Table 1. The inoculum sizes were fixed (10–30 %) on volume per volume basis as to envisage its effects for CO2 removal and the optical density of 10, 20 and 30 % inoculum sizes used in the study were recorded as 0.594, 0.692 and 0.802, respectively, measured at 660 nm using UV Visible Spectrophotometer (Cyberlab, USA). The pH of the medium was adjusted using 0.1 N NaOH and 0.1 N HCl. All the flasks were manually shaken thrice a day in order to avoid sticking of culture to flasks. The experiments were carried out in duplicates and the average has been taken RSM analysis.
Response surface methodology
In order to study the combined effects of the variables (pH, inoculum size and sodium bicarbonate) on the maximum removal of CO2 (%), 20 sets of experiments with appropriate combinations of pH, inoculum size and NaHCO3 concentration were conducted using response surface method (statistical analysis) and the details are presented in Table 2. The CCD under the response surface methodology (RSM) was employed in order to illustrate the nature of the response surface in the experimental design and to elucidate the optimal conditions of the most significant independent variables. A flowchart representation in support of the response surface methodology has been presented in Fig. 1. In this analysis, NaHCO3, inoculum size and pH were chosen as independent variables and the carbon dioxide (CO2) removal rate (%) and its corresponding chlorophyll content were taken as dependent output response variable.
The three independent variables were varied over two levels with pH between (4 and 8) relative to the centre point (pH 6), the second independent variable (NaHCO3 in g/l) was varied over two levels (3.3 and 9.9 g/l) relative to the centre point (6.6 g/l) and the third independent variable (inoculum size in %) was varied over two levels (10 and 30 %) relative to the centre point (20 %).
The full factorial CCD matrices of three variables with respect to their uncoded (real) and coded values are presented in Table 2. The response surface method was constructed using MINITAB 16 statistical software. Evaluation of the goodness of fit of the model is done through coefficient determination and analysis of variances. The experimental results were fitted to a second order polynomial Eq. (1):
where Y is the dependent variable (CO2 removal and chlorophyll content); A, B and C are the independent variable; β 0 is the regression coefficient at center point; β 1, β 2 and β 3 are the linear coefficients; β 11, β 22 and β 33 are the quadratic coefficients and β 12, β 13 and β 23 are the second-order interaction coefficients. The developed regression model was evaluated by analyzing the values of regression coefficients, analysis of variance (ANOVA), P and F values. The quality of fit of the polynomial model equation was expressed by the coefficient of determination, R 2. The statistical software package was used to identify the experimental design as well as to generate a regression model to predict the optimum combinations considering the effects of linear, quadratic and interactive effects on CO2 removal and corresponding chlorophyll content.
Carbon dioxide removal
Alkalinity based titrimetric method was used to find out the dissolved inorganic carbon species (\({\text{H}}_{2} {\text{CO}}_{3}^{*}\), HCO3 −, CO3 2−) by following standard method (APHA 2005). Briefly, all the samples were centrifuged to obtain supernatant which was titrated against standardized H2SO4 (0.02 N). In a typical experiment, 10 ml of supernatant was taken in a beaker and titrated against H2SO4 using phenolphthalein (pKa 8.6) indicator. After the first end point, titration was continued using methyl orange (pKa 3.8) as the indicator to get the second end point. The readings were noted down and the dissolved inorganic carbon species (\({\text{H}}_{2} {\text{CO}}_{3}^{*}\), HCO3 −, CO3 2−) were determined using the formulae in standard method and the sum of the three species are represented as total inorganic carbon species CO2 as mg CaCO3/l which is shown in Eq. (2). Furthermore, the ratio of CO2 to CaCO3 is 1.4 which is taken for CO2 estimation from total inorganic carbon species and the same has been shown in the Eq. (3) (Kemmer 1979).
The CO2 removal (%) was determined by calculating difference between the initial concentration of CO2 (based on Eq. 3) from each experimental runs and final concentration after growth in stationery phase (until no observation of CO2 removal was found) and is expressed below
Chlorophyll analysis
The chlorophyll content in the medium is determined by spectrometric analysis. Briefly, 5 ml algae culture was centrifuged at 10,000 rpm for 10 min. The supernatant was drained off and the sample was re-suspended in ethanol/diethyl ether and kept boiling for 5 min. After boiling, the sample was made up to 5 ml with ethanol/diethyl ether. The optical density was measured at 660 nm and 642.5 nm with solvent as a blank. The chlorophyll content was determined using the formula (Becker 1994):
Results and discussion
Central composite design: response surface estimation
The growth of C. pyrenoidosa under experimental conditions and optimized condition is shown in Fig. 2. It can be noted that, there was a twofold increase in the chlorophyll accumulation in the optimized condition compared to the experimental condition which may be due to the availability of carbon source that helps in synthesizing chlorophyll. The experiments based on design (Table 2) were lasted for 20 days after which the growth was stationery and hence no further improvement was observed on chlorophyll accumulation and CO2 removal and the same has been given as experimental data in RSM. The results of CO2 removal and chlorophyll content (both predicted and experimental) for different design variables (pH, inoculum size and NaHCO3) are presented in Table 3. The second-order polynomial Eq. (1) are fitted with experimental results of maximum CO2 removal (%) and corresponding chlorophyll content from the estimated regression coefficients. The regression coefficients for CO2 removal and chlorophyll content are presented as Eqs. (6) and (7), respectively.
Analysis of variance and residuals
The regression helps to correlate the experimental data with predicted response. R 2 and adjusted R 2 values represent the proportion of variation in the response that is explained by the model where R describes the amount of variation in the observed responses. The value of R 2 is also a measure of fit of the model and the adjusted R 2 value compares models with different independent variables. The ANOVA results are presented in Tables 4 and 5 and it can be noted that, the R 2 values for CO2 removal and corresponding chlorophyll content are 0.9527 and 0.962 which indicates high degree of correlation between experimental and predicted values.
The estimated regression coefficients for removal of CO2 and chlorophyll content are presented in Tables 6 and 7, respectively, along with their corresponding P value and T values. It can be observed from Table 6 for CO2 removal (%) that, the coefficient for single effect of pH (β 1), sodium bicarbonate (β 2) and inoculum size (β 3) (P < 0.050) are highly significant whereas the square effects i.e., linear co-efficient β 11, β 22 and β 33 and the interactive terms β 23 are not significant except β 13 which is significant. From Table 7 (chlorophyll content) the coefficients for single effect except inoculum size (β 3) are significant whereas the interactive and square effects except β 11 are significant.
Response surface plots for CO2 removal
The main objective of the response surface method is to find out the optimum condition for maximum CO2 removal with respect to the chosen variables. The interaction effects between the variables (pH and sodium bicarbonate) for carbon dioxide removal is presented in Fig. 3a, as the sodium bicarbonate concentration increases concomitantly with increase in pH, the removal of CO2 increases. This is due to the fact that the microalgae uptake the HCO3 inside the cell and by the action of carbonic anhydrase, it converts HCO3 into CO2 inside the cell. The observations are consistent with the results reported in the literature (Devgoswami et al. 2011).
Similarly, the interaction effects between the variables (inoculum size and pH) for carbon dioxide removal is presented in Fig. 3b, it can be observed at low pH, even if the inoculum size is high; there is a decrease in the CO2 removal. This could be due to the fact that at low pH all the carbon dioxide will exist in the form of free CO2 (H2CO3) as the algae cannot utilize for metabolic activity (Van Den Hende et al. 2012). Figure 3c depicts the interaction effect between the variables (inoculum size and sodium bicarbonate) for CO2 removal. It can be noted from the figure that, increase in inoculum size with concomitant decrease in sodium bicarbonate concentration, helps to increase the uptake of CO2 (i.e. CO2 removal). This could be due to the regulation of H+ ions into the cell takes place due to which the hydroxide is formed which in turn affects the CO2 removal process (Yeh et al. 2010). In addition, it is also reported that maximum CO2 removal varies with different environment conditions. It is reported that at pH 4 and high bicarbonate concentration (0.3 g/l), maximum removal of CO2 (82.5 %) was achieved (Lam and Lee 2013). Similarly, in another study (Yeh and Chang 2012), it is reported that a maximum removal of CO2 in the range of 90–100 % was achieved with increasing bicarbonate concentration (till 1600 mg/l).
In the present study, the maximum absorption of CO2 was achieved at pH 8 with initial NaHCO3 concentration of 3.33 g/l and higher inoculum size 30 %. However, with increase in concentration of bicarbonate, there is no significant change in CO2 removal which is due to the fact that additional carbon mechanism results in decreased growth rate causing them in reduction of fixing CO2 rates (Lam and Lee 2013).
Response surface plots for chlorophyll content
Chlorophyll a is the photosynthetic pigment that is widely present in all eukaryotic microalgae and is synthesized during photosynthetic process as mentioned in Eq. (8). Initially the inorganic carbon is accumulated into microalgal cell by capture of light energy by pigments such as chlorophyll a and b that are presented in chloroplastida of cell (Wang et al. 2012).
The initial concentrations of chlorophyll are 0.5, 1, 1.34 mg/l for inoculum sizes 10, 20, 30 %, respectively. The surface plots for the interaction effects between the variables (pH and sodium bicarbonate) for the chlorophyll content are presented in Fig. 4a. It can be observed from the figure that, at low sodium bicarbonate concentration, as the pH increases the chlorophyll content increases drastically but at higher sodium bicarbonate concentration only minor variations of chlorophyll content was observed in all pH. This could be due to the excess HCO3 − (Ci) ions which are not utilized by microalgae due to insufficient light, as synthesis of chlorophyll will mainly depend upon the light energy during photosynthesis thereby hindrance the process of synthesizing chlorophyll (Amoroso et al. 1998).
Figure 4b depicts the interaction effects between the variables (inoculum size and pH) for chlorophyll and it can be noticed that at low inoculum size, the chlorophyll content increases with increase in pH. However, the chlorophyll content decreases when the inoculum size increases along with increase in pH. It may be due to the fact that increase in inoculum size causes reduction of H+ ions form the medium (Liu et al. 2014; Chi et al. 2011).
The interaction effects between the variables (inoculum size and sodium bicarbonate) are presented in Fig. 4c and it can be observed from the figure, that the chlorophyll content decreases when the sodium bicarbonate increases along with the increase in inoculum size. This is due to the fact that the increase in sodium bicarbonate decreases the photosynthetic efficiency. The obtained results are in consistent with the results reported in the literature (White et al. 2013).
At higher concentration of bicarbonate and pH, there is no significant change in chlorophyll content which could be due to: (1) increasing rates of photorespiration (2) availability of C:N ratio in the medium as the nitrogen is also one of the factor for chlorophyll assimilation.
Conclusion
The interactive effects between the variables (pH, inoculum size and sodium bicarbonate concentration) for CO2 removal using C. pyrenoidosa in synthetic medium under mixotrophic condition was investigated by employing response surface method with CCD. The maximum removal of CO2 (86 %) was achieved at pH 8 with sodium bicarbonate concentration of 3.33 g/l, and inoculum size of 30 %. The regression value of 0.9527 and 0.962 was observed for CO2 removal and chlorophyll content which implies that the experimental results are statistically significant. The results reveal that C. pyrenoidosa can be used effectively for bio-fixation of CO2 in the form of bicarbonate at alkaline conditions in higher inoculum size under mixotrophic condition. Further investigations on adapting microalgae at alkaline conditions will be a useful for large-scale applications to develop bioenergy feedstock.
References
Abreu AP, Fernandes B, Vicente AA, Teixeira J, Dragon G (2012) Mixotrophic cultivation of Chlorella vulgaris using industrial dairy waste as organic carbon source. Bioresour Technol 118:61–66
Amoroso G, Sultemeyer D, Thyssen C, Fock H (1998) Uptake of HCO3 − and CO2 in cells and chloroplasts from the microalgae Chlamydomonas reinhardtii and Dunaliella tertiolecta. Plant Physiol 116:193–201
American public health association (APHA) (2005) Standard methods for the examination of water and wastewater, 21st edn. AWWA-WPCF, Washington
Becker EW (1994) Microalgae: biotechnology and microbiology. Cambridge University Press, NewYork
Benemann JR (1993) Utilization of carbon dioxide from fossil fuel-burning power plants with biological systems. Energy Convers Manag 34:999–1004
Bhatnagar A, Chinnasamy S, Singh M, Das KC (2011) Renewable biomass production by mixotrophic algae in the presence of various carbon sources and wastewaters. Appl Energy 88:3425–3431
Cheirsilp B, Torpee S (2012) Enhanced growth and lipid production of microalgae under mixotrophic culture condition: effect of light intensity, glucose concentration and fed-batch cultivation. Bioresour Technol 110:510–516
Chi Z, O’Fallon JV, Chen S (2011) Bicarbonate produced from carbon capture for algae culture. Trends Biotechnol 29:537–541
Choi W, Kim G, Lee K (2012) Influence of the CO2 absorbent monoethanolamine on growth and carbon fixation by the green alga Scenedesmus sp. Bioresour Technol 120:295–299
Devgoswami CR, Kalita MC, Talukdar R, Bora J, Sharma P (2011) Studies on the growth behavior of Chlorella, Haematococcus and Scenedesmus sp. in culture media with different concentrations of sodium bicarbonate and carbon dioxide gas. Afr J Biotechnol 10:13128–13138
Feng Y, Li C, Zhang D (2011) Lipid production of Chlorella vulgaris cultured in artificial wastewater medium. Bioresour Technol 102:101–105
Holloway S (2007) In Carbon dioxide capture and geological storage. Philos Trans R Soc 36:1095–1107
Hsueh HT, Li WJ, Chen HH, Chu H (2009) Carbon bio-fixation by photosynthesis of Thermosynechococcus sp. CL-1 and Nannochloropsis oculta. J Photochem Photobiol B Biol 95:33–39
Jeong ML, Gillis JM, Hwang JY (2003) Carbon dioxide mitigation by microalgal photosynthesis. Bull Korean Chem Soc 24:1763–1766
Kemmer FN (1979) The NALCO water handbook, 2nd edn. McGraw-Hill, USA
Khataee AR, Dehghan G (2011) Optimization of biological treatment of a dye solution by macroalgae Cladophora sp. using response surface methodology. J Taiwan Inst Chem Eng 42:26–33
Kim G, Choi W, Lee CH, Lee K (2013) Enhancement of dissolved inorganic carbon and carbon fixation by green alga Scenedesmus sp. in the presence of alkanolamine CO2 absorbents. Biochem Eng J 78:18–23
Lam MK, Lee KT (2013) Effect of carbon source towards the growth of Chlorella vulgaris for CO2 bio-mitigation and biodiesel production. Int J Greenh Gas Control 14:169–176
Lam MK, Lee KT, Mohamed AR (2012) Current status and challenges on microalgae-based carbon capture. Int J Greenh Gas Control 10:456–469
Liu G, Qiao L, Zhang H, Zhao D, Su X (2014) The effects of illumination factors on the growth and HCO3 − fixation of microalgae in an experiment culture system. Energy 78:40–47
Lu C, Bai H, Wu B, Su F, Hwang JF (2008) Comparative study of CO2 capture by carbon nanotubes, activated carbons and zeolites. Energy Fuels 22:3050–3056
Metz B, Davidson O, De Coninck H, Meyer MLL (2005) IPCC report on carbon dioxide capture and storage, 1st edn. Cambridge University Press, New York
Pires JCM, Martins FG, Alvim-Ferraz MCM, Simoes M (2011) Recent developments on carbon capture and storage: an overview. Chem Eng Res Des 89:1446–1460
Rahaman MSA, Cheng L, Xu X, Zhang L, Chen H (2011) A review of carbon dioxide capture and utilization by membrane integrated microalgal cultivation processes. Renew Sust Energy Rev 15:4002–4012
Stewart C, Hessami MA (2005) A study of methods of carbon dioxide capture and sequestration—the sustainability of a photosynthetic bioreactor approach. Energy Convers Manag 46:403–420
UTEX (2009) BG11 Medium Composition. University of Texas Austin, USA. http://web.biosci.utexas.edu/utex/mediaDetail.aspx?mediaID=26. Accessed 22 Nov 2012
Van Den Hende S, Vervaeren H, Boon N (2012) Flue gas compounds and microalgae: (bio-) chemical interactions leading to biotechnological opportunities. Biotechnol Adv 30:1405–1424
Wang JP, Chen YZ, Ge XW, Yu HQ (2007) Optimization of coagulation–flocculation process for a paper-recycling wastewater treatment using response surface methodology. Colloid surface A 302:204–210
Wang B, Li Y, Wu N, Lan CQ (2008) CO2 bio-mitigation using microalgae. Appl Microbiol Biotechnol 79:707–718
Wang Q, Luo J, Zhong Z, Borgna A (2011) CO2 capture by solid adsorbents and their applications: current status and new trends. Energy Environ Sci 4:42–55
Wang H, Fu R, Pei G (2012) A study on lipid production of the mixotrophic microalgae Phaeodactylum tricornutum on various carbon sources. Afr J Microbiol Res 6:1041–1047
White DA, Pagarette A, Rooks P, Ali ST (2013) The effect of sodium bicarbonate supplementation on growth and biochemical composition of marine microalgae cultures. J Appl Phycol 25:153–165
Yeh K, Chang JS (2012) Effects of cultivation conditions and media composition on cell growth and lipid productivity of indigenous microalga Chlorella vulgaris ESP-31. Bioresour Technol 105:120–127
Yeh KL, Chang JS, Chen W (2010) Effect of light supply and carbon source on cell growth and cellular composition of a newly isolated microalga Chlorella vulgaris ESP-31. Eng Life Sci 10:201–208
Zhang Z, Peng J, Qu W, Zhang L, Zhang Z, Li W, Wan R (2009) Regeneration of high-performance activated carbon from spent catalyst: optimization using response surface methodology. J Taiwan Inst Chem Eng 40:541–548
Acknowledgments
The author’s gratefully acknowledge VIT University for providing necessary funds and facilities to carry out the research work. Also, the author’s expresses their sincere gratitude to V. Sowmya, Research Scholar, School of Mechanical and Building Sciences, VIT University for assisting in writing and proof reading the article.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that there is no conflict of interest.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Abinandan, S., Shanthakumar, S. Evaluation of photosynthetic efficacy and CO2 removal of microalgae grown in an enriched bicarbonate medium. 3 Biotech 6, 9 (2016). https://doi.org/10.1007/s13205-015-0314-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s13205-015-0314-5