Abstract
Purpose of Review
Lowering the impact of forest utilisation on the forest environment is a part of the improvement in sustainable forest management. As part of forest utilisation, timber harvesting can also cause environmental implications. The main impact of forest operations is on the soil, on regeneration and on the residual stand. The aim of the present review was to identify the state of the art in forest utilisation, identifying how and how much forest operations affect forest soil, regeneration and the remaining stand. Particular attention was paid to the level of impact and potential to limit this.
Recent Findings
There are a large number of publications tackling forest harvesting, but most of them do not give a comprehensive framework and they mainly focus on one or very few aspects of forest damage. In order to improve general knowledge of the impact of forest operations, it was proposed that the scope of recent findings should be examined and a compilation of the available results from different regions should be presented in one paper.
Summary
It was found that the least impactful machine-based forest operations were harvester–forwarder technologies, while a larger scale of damage could be expected from ground-based extraction systems (skidders) and cable yarders. Animal power, if applicable, tended to be very neutral to the forest environment. A decrease in damage is possible by optimising skid trail and strip road planning, careful completion of forest operations and training for operators. The existence of legal documents controlling post-harvesting stand damage are rare and have been implemented in only two countries; there is no post-harvesting control on soil damage and natural regeneration.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
One of the main and essential aims of the last 20 years within the forestry sector was to improve sustainable forest management (SFM) [1]. SFM includes the ecological aspects of forest operations, and it aims to develop new methods and technologies for sustainable use of forest resources and to minimise any negative impact on the environment [2]. Focusing on forest harvesting, it is important to consider high productivity (economic aspects), a low negative impact on the environment (environmental aspects) and safe working conditions for forest operators (ergonomic and social aspects) [3••]. Forest logging is an impactful operation which could lead to possible implications in forest ecosystem. In particular, in recent years, forest researchers have focused on the impact of forest operations in relation to the soil, the regeneration dynamics and the stand conditions.
It is important to underline that soil is highly sensitive to improper logging activities [4], and the soil environment could suffer substantially over a long period of time thereby affecting forest productivity and ecosystem efficiency [5]. Forest soil impacts with a higher intensity in terms of area are mainly linked to ground-based extraction systems, such as skidding and traditional cable yarding; however, growing harvester and forwarder use, especially in Europe [6], has also impact on soil compaction. With this in mind, one of the most important ecological issues for the forest sector is a minimisation of the ground disturbance caused by forest operations [7]. If not properly implemented, forest operations with extraction based on skidders or large forwarders could lead to high soil compaction [4], and later to soil erosion and rutting, particularly evident along skid trails and strip roads.
The impact on forest regeneration is more complex to evaluate directly. Some studies reported that soil compaction due to the passing of machinery often leads to an inhibition of potential tree regeneration [8, 9•]. On the other hand, in other studies the improved recruitment of seedlings and saplings was observed in areas where soil had been scarified or modified by logging activities [10, 11]. So, this particular aspect of forest operation sustainability is very difficult to analyse unequivocally in the short period of time after an operation.
The impact on the residual stand may decrease the quality of residual trees but also increase tree mortality due to insect and disease infestation [11] and fungal decay [12] as well as lead to stem deformity and significant losses in final crop volume and value [13]. Furthermore, excessive damage to residual trees during logging operations may change aesthetic value and directly influence other ecosystem services, including recreational ones.
Taking into consideration the abovementioned dangers, the methods of felling, processing, bunching and extraction should be planned on a larger scale and for a longer period of time, with consideration to environmental, economic and social contexts [14]. In recent years, much scientific research has been focused on assessing the impact of logging in relation to sustainability, assessing forest ecosystem resilience and suggesting best practice.
In light of the large but scattered number of scientific publications on this topic, this paper is an attempt to bring together the in-depth knowledge and insights of experts within an integrated and comprehensive framework using research collated over the last decade with special attention to the last 5 years. In particular, the aim of this paper was to find out how contemporary studies and good practices contribute to the mitigation of environmental impact due to forest operations, such as soil damage and injuries to natural regeneration and the remaining stand.
Materials and Methods
Literature Research
One of the basic techniques to search for particular documents in a complex database is the use of Boolean Operators. The Boolean search method is a symbolic logic system that creates relationships between expressions and words. The use of Boolean search has the aim of analysing all studies in a specific research field. The research of papers for this review was performed using the databases of Science Direct, ISI Web of Knowledge and Google Scholar. Using the search string “Forest operations impacts” and related synonyms expressions four specific categories, returned, in total, over 944,000 findings, while over 72,000 findings appeared once the search was restricted to research during the last 5 years (Fig. 1).
However, many items identified in the search were not completely related to the addressed topic. Eventually about 90 papers published in the last 5 years were selected and analysed with the focus on the evaluation of forest operations and the results of their impact on the environment, i.e. the soil, regeneration and the remaining stand.
Results and Discussion
Harvesting-Soil Interaction
Soil plays a crucial role in forest ecosystems by transmitting nutrients and water, providing energy flows that are linked to forest productivity and sustain biodiversity [15].
Features of Forest Soil After Harvesting
In terms of the visual features of the soil after a forest operation and the condition of the canopy cover, these can be included in one of the four following types: (I) undisturbed soil, canopy cover not removed (NDS-NCR), e.g. normal control samples; (II) undisturbed soil, canopy cover removed (NDS-CR), e.g. logging gaps without winching corridors; (III) disturbed soil, not canopy cover removed (DS-NCR), e.g. winching corridors; and (IV) disturbed soil, canopy cover removed (DS-CR), e.g. disturbed skid trails, landing sites and processing sites.
How
The physical, chemical and biological properties of the forest soil change as a result of harvesting operations, and this is commonly referred to as soil disturbance [4, 16,17,18,19]. Chemical and biological changes occur in the soil after physical modification. Therefore, changes in the physical properties of the soil are the most prominent indicator of soil disturbance following the use of logging equipment [4, 20]. Detrimental soil disturbance associated with ground-based extraction often includes compaction, rutting, lateral soil displacement, topsoil mixing and the formation of puddles.
A large number of factors influence the extent and severity of soil compaction. As found by many authors, overall harvesting operations can lead to a reduction in soil porosity [14, 19,20,21,22,23], increased soil erosion [20,21,22,23,24] and a decrease in root penetration and length expansion [19].
Soil compaction can lead to reduced water infiltration and hydraulic conductivity, which contributes to increased waterlogging on flat terrain and soil runoff with erosion on slopes. Soil compaction can reduce the access of plant roots and microorganisms to water, oxygen and nutrients. Long-lasting damage to the soil system can negatively affect forest productivity and ecosystem functionality [5]. One way to estimate the severity of logging damage to the forest soil is to measure soil bulk density before treatment and compare it with its critical level after harvesting operations [25, 26].
Picchio et al. [19] reported higher soil penetration resistance 10 years after skidding. An increase in the bulk density of soil should not always be regarded as equivalent to a detectable decrease in tree growth. Changes in soil bulk density that have led to some decline in the biological and vegetative development of beech and maple seedlings have been observed when increased by 0.15 to 0.43 g cm−3 [19]. Depending on soil type and tree species, the number of changes in soil compaction that will result in reduced plant growth varies. In this context, specific surveys are necessary to assess the real occurrence of the negative effects of bulk density increment on tree growth.
An important factor differentiating soil changes after harvesting is the impact of different machinery. Allman et al. [27] compared the influence of different logging machines on soil compaction and reported that all wheeled machines caused the same amount of soil compaction in the ruts, despite differences in tires, machine weight, etc. Cambi et al. [28] studied the effect of bogie tracks on the physical properties of the soil during forwarding operations in a coniferous stand in north-eastern Italy. The authors reported a clear difference in the physical parameters of the soil before and after operations. Eroğlu et al. [29] studied the effects of four timber logging techniques (cable yarder, skidder, manpower and chute system) on some physical and chemical properties of the soil in Turkey’s forests. It was found that logging by skidder can have a clear influence on soil permeability, bulk density and soil water balance, and that skidding can reduce the content of organic matter and nutrient levels in the soil.
Lang et al. [30] studied the influence of mechanical site preparation treatments on the physical properties of disturbed soils in harvested wet lands. Their results showed that macroporosity had not recovered to the pre-harvest levels for any site preparation treatments except Mole-Plowed; bulk density and total porosity recovered to near pre-harvest levels for all treatment combinations, but saturated hydraulic conductivity rates remained lower than the pre-harvest values.
Summarising, forest operations usually lead to changes in the soil’s physical, chemical and biological characteristics. One of the most important factors influencing soil impact intensity is the level of mechanisation, as well as machine weight and type of operation (i.e. skidding or forwarding). Soil compaction can be reversed; however it may take more than 10 years for full rehabilitation [31].
How Much
The extent and severity of soil disturbance during harvesting operations depends on several factors that can be divided into three groups:
-
1.
Stand conditions: extracted timber volume [28, 32], soil type and texture [33,34,35], soil moisture content [25], soil’s organic matter content, site topography [34, 35], stand density and canopy extension [34, 35];
-
2.
Yard logistics: harvesting system, advanced level of logging operation planning, type of machines, logging method [28, 32], machine and load mass, tire pressure, vibrations transmitted by vehicles [20], intensity of machine traffic [32], weather conditions during skidding operation, training, experience and expertise of operators as well as planning and worker proficiency [36];
-
3.
Forest road network characteristics: density of roads and skid trails, slope gradient of skid trail [20].
Expansion of soil damage by logging depends on the type of technology used [4, 17]. More pressure, slipping and a lower speed can dramatically increase soil disturbance on a steep slope trail. Venanzi et al. [37] demonstrated that physical, chemical and biological features of the soil can be greatly impacted by harvesting operations and consequently, eventually soil mesofauna could be changed. In particular, heavy ground-based logging equipment can cause severe and long-lasting damage of the soil system, which can negatively affect forest productivity and ecosystem function [5, 16, 38]. The results of various studies of the impact of mechanised harvesting on forest soil show that changes to the soil can be very different, from low to very high, including values that exceed 100% (Table 1).
In addition, at a low level of mechanisation, Jourgholami and Majnounian [39] reported that mule logging had a statistically significant effect on soil bulk density along mule trails before and after extracting. Soil bulk density increased significantly as animal passes increased in number; however, the degree and level of compaction did not differ with increasing trail slope. In contrast, Badraghi et al. [53] evaluated soil disturbance and compaction caused by mule extraction and reported that only 1% of the harvested area was disturbed, and soil bulk density increased only by 0.3%.
Limiting and Preventing Disturbance
One goal of forest managers in harvesting should be to minimise the impact of vehicles on the soil, the negative effects of which can be significant and long lasting, although often unrecognised or neglected [4]. The ongoing trend to constantly increase the size, power and load of machines makes it even more imperative to plan logging logistics in order to limit soil disturbance and stand damage [11]. In the available studies, suggestions to reduce soil damage due to forest operations can be grouped into the following:
-
1.
Machine traffic should be carried out (if possible) during dry and favourable weather conditions [27, 44, 54,55,56], and it is important to reduce the number of load passes.
-
2.
The proper design of forest roads can play an important role in reducing soil disturbance [18, 55,56,57,58,59], and it is important to reduce the trail slope gradient.
-
3.
Both training and supervision can be efficient in soil impact mitigation [12, 14].
-
4.
Employing ameliorative site preparation could contribute to initial survival and an increase in early growth on harvested stands with wet soil conditions [16, 30].
-
5.
Applications of straw and sawdust mulch following skidding operations can reduce surface runoff and sediment on skid trails [16, 49].
-
6.
Traditional animal power with a low impact on the soil can be used for timber extraction in steep terrain conditions [39].
Harvesting-Tree Regeneration Interaction
Timber harvesting represents also a key factor in the ecological management of stands, changing (in negative or positive way) stand structure and species diversity [13, 60]. Availability to sunlight, reduction in plant competition and scarified soils are needed for tree regeneration, and these favourable conditions can be created by harvesting operations [10, 61•]. Proper harvesting operations not only control the amount of sunlight that reaches the forest floor but also make the soil and site conditions ideal for the successful natural regeneration of trees [61•]. Forest managers applying close-to-nature silviculture plan harvesting systems to control the available light on the forest floor in order to obtain regeneration species diversity. In addition to the positive impact of harvesting, mechanical damage to young trees is often an inevitable side effect. With this in mind, good forestry practice should consider ways to mitigate these negative effects.
How
Effect on Seedling Growth
The felling of trees and the opening of the forest canopy increases the intensity of light reaching the forest floor, and the establishment and growth of a tree’s regeneration is positively affected [13]. Disturbances that open small canopy gaps create environmental heterogeneity, particularly the amount of light and water reaching the forest understory, and thereby provide a range of regeneration niches for trees and other plants [60]. In addition, scratches on the surface of forest soil due to skidding create favourable conditions for seed germination and further sapling growth [10]. However, in some research it was found that the germination rate had a strong negative correlation with an increase in soil bulk density [22,23,24, 62]. Moreover, germination rates and growth could be significantly reduced by the number of passes and the trail slope gradient [19, 22, 23, 55]. The height of seedlings was also found to be lower on machine operating trails than in undisturbed areas [63]. The effects of soil compaction may create particularly challenging conditions for seedling survival during drought periods, because seedlings with short roots may be unable to access water at deeper soil levels [44, 55].
Mechanical Damage
Forest regeneration can be affected by mechanical damage during harvesting [18]. The extent and severity of damage to forest regeneration can be influenced by several factors, from which the logging system and harvesting intensity seem to be the most influential (Table 2).
In forest with a natural regeneration system, after shelter-wood and selection cuttings, damage to saplings is common and usually inevitable. When timber harvesting has advanced planning and the developed forest operation is applied, a reduction in damage to regeneration may be more feasible. Damaged regeneration by tree felling operations is usually in the form of stem breakage, while the winching operation usually causes uprooting [18]. When trees are growing, stem flexibility decreases, the probability of uprooting reduces while the probability of stem breakage increases [18]. The amount of regeneration damage in the winching stage is usually higher than in the felling and skidding stages. This was also confirmed by Picchio et al. [63], where bunching (during winching) was the main cause of damage to regeneration during cable skidder logging, and the amount of regeneration damage on steep slopes was higher than on gentle slopes.
The amount of damage to regeneration can decrease when workers have more experience [61•]. Soil scarification can increase the success of natural regeneration [10], but at the same time soil compaction may reduce the establishment of regeneration [44] and growth of regeneration [23]. Compacted soil layers due to forest machine traffic are the most common problem affecting seedling regeneration after forest harvesting [23, 432, 44]. García-Orenes et al. [68] reported that salvage logging may damage the bank of seedlings and affect plant regeneration after fire, reducing plant density. Salvage logging can also decrease the amount of natural tree regeneration [24, 69]. Fernández and Vega [70] found no detrimental effect of a salvage logging treatment compared with natural regeneration. These contradictory results could be due to factors such as the type of soil, when and how the salvage logging treatment is carried out and meteorological conditions which can be decisive.
How Much
The share of regeneration that can be damaged during different logging systems can vary from several percent to more than 60% (Fig. 2) [67]. The mean frequency of damage on seedlings, small saplings and large saplings were 8.8%, 12.8% and 19.5%, respectively, in skidder extraction in mixed beech stands [18]. A lower level of damage was observed after cable-skidding and ranged from 4.9 to 7.1% [18]. Stańczykiewicz et al. [74] studied the damage of regeneration using two systems: (1) a tower cable system combined with farm tractor and (2) a skidder in a mature spruce stand. The damage of regeneration using the tower cable system (23.9%) was lower than using the skidder system (61.3%). The tower cable system mostly destroyed regeneration, while during skidder logging, it is usually stem and side-branches that can be broken. Most damage to regeneration using the tower cable system occurred on the shortest regeneration (up to 0.5 m from the ground), while skidder logging usually affected the regeneration of medium height (0.5–4.0 m).
Limiting and Preventing Damage to Regeneration
Damage to regeneration can be limited by introduction of the following:
-
1.
Identifying and Marking fragments of regenerated stands for protection and avoiding winching through these stands; planing of skid trails and lay out landings should be carried out before harvesting operations begin.
-
2.
Focusing on protection of the residual stand rather than on the trees being removed.
-
3.
Considering the felling season, there is usually less damage during the winter months.
-
4.
Matching machine/equipment type, size and deployment to stand and site conditions [19].
-
5.
Limiting or concentrating machine activity on skid trails and access corridors.
-
6.
Increasing awareness of the consequences of mechanical injuries to trees and forest stands.
-
7.
The use of the snatch block could positively improve the winching operation.
-
8.
Alternatively, when possible and when financially acceptable, different forms of extraction should be used, for example, cable cranes or traction-winch-supported forwarders [74].
-
9.
A detailed planning strategy will reduce damage to a level which is acceptable and predictable [12].
-
10.
For a post-harvesting assessment of a logging operation, obtaining an accurate measure of residual stand damage is recommended [12, 18].
-
11.
A post-harvest inventory of soil and stand damage, and prioritisation of contractors that have a good level of training, should be carried out for reduced impact logging (RIL) [19].
Harvesting-Stand Interaction
Forest operations influence the stand condition, which can be measured by taking into account several factors, mainly environmental, social and economic [3••], as well as ergonomic factors and those linked to product quality [75].
It may be considered that the level of damage depends on the machine operator’s skills; however, there are certain objective reasons that can cause a higher probability of damage. The level of damage caused to residual trees during forest operations has been described by several authors and many factors influencing damage level have been indicated. As a summary of these factors from different findings, Siren et al. [76] quote in their publication that the level of damage depends on the forest characteristics, such as the amount of timber removed during harvesting, stand density and basal area. In addition, well designed access to the forest can limit the probability of damage, such as skid-trail spacing or road density [12]. Extracting timber on steeper slopes usually causes more damage [19, 77, 78].
It was also found that tree injuries depend on the season, and can be higher in summer [79], as well as affected by stand structure: in uneven-aged stands, damage can be more frequent, especially among younger trees [76]. Mechanised harvesting tends to cause less damage than using a chainsaw for felling and more damaged trees are observed near strip roads [80, 81]. The harvesting system definitely influences the level of damage: the long wood system (LWS) is usually associated with a higher probability of damage compared with the short wood system (SWS) [82].
Wounds created due to bark and cambium removal can heal; however, bark pockets or stone pockets are created, defects difficult to detect many years after wounding, especially if they occurred on a young tree. Newly grown wood tissue can cover the wounded area, but the disjunction between the old and the new tissue can create ring shake. Generally, wounds negatively impact diameter growth which may slow down by 8–13% [12, 83]. The healing rate is faster on younger trees if the wound is higher on a tree and at a lower elevation [18]; a slower healing process was observed on bigger wounds as well as on southern slopes [18].
In addition to discontinuity in the wood, sometimes irregular stem forms, local grain deviations and colour variations (not necessarily pathological) can be observed. However, injured trees can have a high risk of pathogen infections following harvesting damage, since open wounds with missing bark and cambium can be susceptible to fungi. Bark inclusions reduce the mechanical strength and the aesthetic appeal of artefacts; therefore, they are not accepted in timber for packaging or for flooring. Wounded trees are affected negatively, they produce lower-quality timber [84] and a lower diameter increment can be observed [12, 83].
An analysis of the presented findings shows that the most important and principle injuries to the remaining stand are bark and cambium removal from trees. Most of the damage is observed close to the skid trails. Trees with damage will produce lower quality timber and are vulnerable to fungi and rot development.
How
Damage to the remaining stand can be observed after thinning, selective cutting or another partial tree removal from a stand [76]. Damage is generally understood as bark and cambium removal with partial wood tissue disturbance, also a broken tree. It is considered that damage can occur due to felling, processing or timber extraction [76]; however, it was also confirmed that rolling rocks in hilly areas can be a reason for damage to remaining trees [85•]. Additionally, another cause of damage which is as frequent as injuries generated by harvesting, can be animal browsing which affects ca. 3–4% of wounded trees in the stand, or twice as many in spruce stands [86].
During harvester–forwarder operations, it is usually the felling and pulling of trees by the harvester boom which injures the remaining trees [76]. In motor manual operations with a chainsaw in LWS, it is usually skidding rather than felling which creates more damage [12, 84]. If winching and skidding are analysed as two separate operations, it can be seen that skidding causes more damage to the remaining stand [78].
How Much
In practice, thinning or selective cutting operations are rather associated with some level of damage to the remaining stand, although it is occasionally possible to complete the extraction of short logs using animal power without causing damage [53]. However, in order to keep damage at an acceptable level, legal requirements or limitations have been implemented in some countries to control damage to the trees. In Finland, for example, if the percentage of trees with damage is over 15%, it exceeds the limit of the Forest Act [76]. In Poland, the usual acceptable level of damage to the remaining stand after thinning is 5%. Usually, there are financial consequences when a higher share of trees is injured.
Short Wood System vs Long Wood System
Less intensive damage is usually observed in CTL in thinning, and on average only 7–8% trees can be affected, with no particular difference between older (70–75 y.o.) and younger stands (30–35 y.o.) or species: oak or spruce [87]. Cudzik et al. [48] confirmed a lower level of damage, 4–6% in thinned stands, where CTL was used, and 9–12% for chainsaw felling with skidding in the late thinning of pine stands.
This was also mentioned by Siren et al. [76], who compared studies from Slovenia from the last decade, where CTL caused 13–15% and 17–19% when motor-manual technology was used. A similar level of damage (14–17%) was observed after skidding in an even-aged stand of Corsican pine [73]. An interesting feature of this study was that, 10 years after harvesting/skidding, more damage was revealed (17%), which was explained by the fact that some trees may be hit but have no bark removal, and the consequences of this (dead cambium) may become visible after many years. Further studies, after 20 years, revealed nearly 18% of damage and that increase was explained by the mortality of some trees [11]. This study also confirmed that skidding caused more damage than felling, and the same was confirmed by Tavankar et al. [88] (16.3% and 5.2% by skidding and felling, respectively).
To reduce the level of damage while skidding, the short wood system (SWS) may be applied. In studies carried out by Jourgholami [89], there were 44% fewer damaged trees when SWS was used during skidding. There were also ca. twice as many trees with damage when LWS was applied compared with SWS in close proximity to the skid trails (up to 3 m). This study, however, does not present the productivity when SWS was used.
Nevertheless, there was a substantial difference when LWS was used with skidding as extraction, which left 18% of trees with damage and more than double (45%) the number of injured trees when large and long logs from a much older stand, i.e. 110 y.o. oak were skidded [87]. The same authors observed that a higher thinning (or shelterwood cutting) intensity can cause a higher level of damage. More injured trees were also observed closer to the strip or skid roads [87]. When tracked machines were used more damage to the roots was observed, although studies were carried out in spruce stands, and these trees have roots which are only partially under the surface of the soil [87].
Sirén et al. [76] also provided an interesting method for damage estimation, which considered monitoring the number of trees with damage during the whole life of the stand. According to these authors, modelling showed that during a 160-year rotation period and after 10 thinnings, the total number of damaged trees continuously grew and reached 90% at the end of the rotation. Sirén et al. [76] also mentioned that in old stands, a higher share of damaged trees (64–70%) can be recorded.
Furthermore, in the study by Sirén et al. [76] in uneven-aged stands, the percentage of damaged trees (according to the classification of the Forest Act) was 13.8%. Usually in selection cuttings it is very difficult to reach low damage levels typical for even-aged stands.
Full Tree System
The full tree system (FTS), in which felled trees with branches are extracted, can also leave a substantial share of the trees with damage. In a study carried out in Italy, there were 35–50% of the trees with damage after the skidding or yarding of whole trees using various methods. The use of snatch blocks when skidding and semi-automatic carriage when yarding were effective in limiting the damage level, while snatch blocks also turned out to be effective in limiting damage without a loss in productivity [17]. A high level of damage was also observed when a feller–buncher was used in Spain, where up to 50% of the remaining trees in coppice stands had some damage [90]. A lower harvesting intensity could cause a lower level of damage in FTS, i.e. up to 22% (in tropical forest conditions) [91]. However, in that study, less than one tree per hectare was harvested, albeit of large DBH sizes ranging from 60 to 216 cm [91].
Animal Power
A very low level of damage can be observed when animal power is used. Animal extraction was completed without any damage [53] when short wood was extracted by carrying, or very low, ca. 3% when animal skidding on the ground was provided.
Limiting Stand Damage
Taking into account the studied literature, there are few proposals for limiting stand damage. Basically, many authors suggest careful harvesting and skidding with particular attention to areas close to skid roads. However, a suitable design of skid roads can limit the level of damage. There is also the more objective possibility of using CTL technology and animal force, which tend to cause very low levels of damage to up to 5% of the remaining trees in the stand (Fig. 3). A high level of damage is mainly observed during skidding, when long wood is extracted or a whole tree system is applied (Fig. 3). These systems require particular attention when timber extracting is in operation.
Conclusions
Felling and extracting of timber from forests has an inevitable impact on the environment. This impact is either in the form of soil disturbance, regeneration or stand damage.
Soil Damage
Soil damage seems to be the most difficult to avoid. Any machine (or animal power) has impact on the soil, especially at the stage of timber extraction. Soil disturbance includes a change in the physical properties, followed by modifications in the chemical and biological properties. Common methods used to estimate soil damage severity include the measurement of bulk density or penetration resistance which is compared with critical values, when possible. For example, regarding bulk density, critical values are limiting factors for root growth, depending on the type of soil, and they vary from 1.4 Mg m−3 for clay soils to 1.8 Mg m−3 for sand and loamy sand soils. The organic carbon or CO2 concentration and QBS-ar index are parameters which also appear in the latest research widening the knowledge of soil reactions to forest operations.
Damage expansion generally depends on the method of forest operation and the machines used, mainly their weight, load and number of passes. Weather conditions, tyre variations and size are also essential in limiting rutting and general soil erosion. Good forest roads and skid trail (strip road) networks, as well as their quality, can be essential in limiting soil damage. Nevertheless, damage and erosion on slopes with greater gradients are difficult to control. However, erosion control can be achieved when brushwood, straw or chips/sawdust mulch are applied on skid roads during and after extracting. In any cases of changes in soil properties, it is worth noticing whether soil regeneration takes place, and if not, a reclamation process can be put in place to return the soil to the pre-harvest state.
Regeneration Damage
Forest operations can be very severe for forest regeneration. However, it is worth mentioning that harvested trees open the canopy and initiate soil scarification which contributes to future tree growth. On the other hand, germination, young tree growth and root development can be negatively affected after forest operations, where an increase in bulk density was observed after high traffic intensity or on steeper slopes.
Ground-based extraction-transport systems, where timber has direct contact with the soil, usually cause more damage to regeneration than other systems such as forwarding or aerial transport systems.
Limiting damage in natural regeneration is difficult as young trees grow at a higher density. Using forwarders and sky yarders should limit injury, as well as the planning of skid roads and winching corridors before felling and extracting.
Stand Damage
The presented results have shown that it is possible to restrict the level of damage to the remaining stand at a low level by using mechanised CTL forest operations. In harvester–forwarder-based thinnings, damage should be at level of over several percent of the remaining trees, although it can occasionally reach ca. 20%. This level, however, should be treated as exceptional. A higher share of injured trees can be observed when skidding is used, and it can vary from ca. 10 to 20% in the long wood system. However, this may double when full trees are extracted. When yarding is used, the expected damage can also vary from 35 to 50%.
Post-Harvesting Assessment
According to the studied literature, there are local prerequisites that may be helpful in limiting damage to the remaining stand. Taking into account best practice, there are two European countries that have legal prerequisites to control stand damage: in Poland, no more than 5% of the remaining trees should have injuries. If the percentage is higher, financial penalties may be imposed on the entrepreneurs carrying out forest operations. In Finland, legal regulations accept damage no higher than 15%. The literature analysis presented shows that there is no control on the amount of soil damage as well as natural regeneration. The area of soil damage can be controlled naturally by the design and establishment of permanent skid trails (for skidders) or strip roads (for forwarders). However, in both cases, there is still the possibility of additional damage due to unskilled operators. The same can be observed in natural regeneration. Therefore, the setting of maximal limits, as in the case of stand damage, should further limit soil disturbance and injuries to natural regeneration.
References
Papers of particular interest, published recently, have been highlighted as: • Of importance •• Of major importance
Higman S, Mayers J, Bass S, Judd N, Nassbaum R. The sustainable forestry handbook: a practical guide for tropical forest managers on implementing new standards. London: Earthscan; 2005.
Heinimann H. Forest operations engineering and management – the ways behind and ahead of a scientific discipline. Croat J For Eng. 2007;28:107–21.
•• Schweier J, Magagnotti N, Labelle ER, Athanassiadis D. Sustainability impact assessment of forest operations: a review. Curr Forestry Rep. 2019;5(3):101–13. https://doi.org/10.1007/s40725-019-00091-6This paper provides a comprehensive review of sustainability indicators and their application in sustainability impact assessments. One of the key conclusions was that the inclusion of indicators measuring the extra value of the forest should be considered. The authors suggest adopting sensitivity analysis during the assessment of key processes to observe the effect on the hot spots.
Cambi M, Certini G, Neri F, Marchi E. The impact of heavy traffic on forest soils: a review. Forest Ecol Manag. 2015;338:124–38. https://doi.org/10.1016/j.foreco.2014.11.022.
Hartmann M, Niklaus PA, Zimmermann S, Schmutz S, Kremer J, Abarenkov K, et al. Resistance and resilience of the forest soil microbiome to logging-associated compaction. ISME J. 2014;8:226–44. https://doi.org/10.1038/ismej.2013.141.
Mederski PS, Karaszewski Z, Rosińska M, Bembenek M. Dynamics of harvester fleet change in Poland and factors determining machine occurrence. Sylwan. 2016;160(10):795–804.
Edlund J, Keramati E, Servin M. A long-tracked bogie design for forestry machines on soft and rough terrain. J Terrramech. 2013;50(2):73–83. https://doi.org/10.1016/j.jterra.2013.02.001.
Bekele A, Kellman L, Beltrami H. Plot level spatial variability of soil organic carbon, nitrogen, and their stable isotopic compositions in temperate managed forest soils of Atlantic. Canada Soil Sci. 2013;178(8):400–16.
• Cambi M, Hoshika Y, Mariotti B, Paoletti E, Picchio R, Venanzi R, et al. Compaction by a forest machine affects soil quality and Quercus robur L. seedling performance in an experimental field. Forest Ecol Manag. 2017;384:406–14. https://doi.org/10.1016/j.foreco.2016.10.045This paper provides a detailed investigation about the effects of soil compaction on soil physical parameters, microarthropod biodiversity, soil respiration, as well as growth and physiology of Pedunculated Oak (Quercus robur) seedlings. Two levels of soil compaction were simulated, i.e. 10 tractor passes vs. 25 tractor passes. One of the key conclusions was that limited access and acquisition of nutrients and water due to the shorter length of main root likely played a key role for growth and physiological responses to soil compaction.
Behjou FK. Tree regeneration following ground-base skidding in a Caspian forest. Austrian J For Sci. 2017;134(2):149–61.
Picchio R, Venanzi R, Latterini F, Marchi E, Laschi A, Lo Monaco A. Corsican pine (Pinus laricio Poiret) stand management: medium and long-lasting effects of thinning on biomass growth. Forests. 2018;9(5):257. https://doi.org/10.3390/f9050257.
Tavankar F, Nikooy M, Picchio R, Bonyad A, Venanzi R. Effects of logging wounds on Caucasian Alder trees (Alnus subcordata C.A. Mey.) in Iranian Caspian forests. Croat J For Eng. 2017;38(1):73–82.
Tavankar F, Bonyad A, Majnounian B. Affective factors on residual tree damage during selection cutting and cable-skidder logging in the Caspian forests, Northern Iran. Ecol Eng. 2015;83(8):505–12. 1068 https://doi.org/10.1016/j.ecoleng.2015.07.018.
Picchio R, Spina R, Calienno L, Venanzi R, Lo MA. Forest operations for implementing silvicultural treatments for multiple purposes. Ital J Agron. 2016;11:156–61. https://doi.org/10.4081/ija.2016.789.
Dominati EJ, Patterson M, Mackay AD. A framework for classifying and quantifying the natural capital and ecosystem services of soils. Ecol Econ. 2010;6:1858–68. https://doi.org/10.1016/j.ecolecon.2010.05.002.
Jourgholami M, Soltanpour S, Etehadi Abari M, Zenner EK. Influence of slope on physical soil disturbance due to farm tractor forwarding in a Hyrcanian forest of northern Iran. iForest. 2014;7(5):342–8. https://doi.org/10.3832/ifor1141-007.
Marchi E, Picchio R, Spinelli R, Verani S, Venanzi R, Certini G. Environmental impact assessment of different logging methods in pine forests thinning. Ecol Eng. 2014;70:429–36. https://doi.org/10.1016/j.ecoleng.2014.06.019.
Tavankar F, Bonyad AE, Nikooy M, Picchio R, Venanzi R, Calienno L. Damages to soil and tree species by cable-skidding in Caspian forests of Iran. For Syst. 2017;26(1):1–9. https://doi.org/10.5424/fs/2017261-09100.
Picchio R, Tavankar F, Nikooy M, Pignatti G, Venanzi R, Lo Monaco A. Morphology, growth and architecture response of Beech (Fagus orientalis Lipsky) and Maple tree (Acer velutinum Boiss.) seedlings to soil compaction stress caused by mechanized logging operations. Forests. 2019;10:771. https://doi.org/10.3390/f10090771.
Solgi A, Naghdi R, Tsioras PA, Nikooy M. Soil compaction and porosity changes caused during the operation of Timberjack 450C Skidder in Northern Iran. Croat J For Eng. 2015;36(2):77–85.
Naghdi R, Solgi A, Zenner EK. Soil disturbance caused by different skidding methods in mountainous forests of Northern Iran. Int J For Eng. 2015;26:212–24. https://doi.org/10.1080/14942119.2015.1099814.
Naghdi R, Solgi A, Labelle ER, Zenner EK. Influence of ground-based skidding on physical and chemical properties of forest soils and their effects on maple seedling growth. Eur J Forest Res. 2016;135:949–62. https://doi.org/10.1007/s10342-016-0986-3.
Solgi A, Naghdi R, Marchi E, Laschi A, Behjou FK, Hemmati V, et al. Impact assessment of skidding extraction: effects on physical and chemical properties of forest soils and on maple seedling growing along the skid trail. Forests. 2019;10:134. https://doi.org/10.3390/f10020134.
Wagenbrenner JW, Robichaud PR, Brown RE. Rill erosion in burned and salvage logged western montane forests: effects of logging equipment type, traffic level, and slash treatment. J Hydrol. 2016;541:889–901. https://doi.org/10.1016/j.jhydrol.2016.07.049.
Allman M, Ferenčík M, Jankovský M, Stanovský M, Messingerová V. Damage caused by wheeled skidders on cambisols of Central Europe. Croat J For Eng. 2015;36(2):205–15.
Lupardus RC, McIntosh ACS, Janz A, Farr D. Succession after reclamation: identifying and assessing ecological indicators of forest recovery on reclaimed oil and natural gas well pads. Ecol Indic. 2019;106(105515):1–14. https://doi.org/10.1016/j.ecolind.2019.105515.
Allman M, Jankovský M, Messingerová V, Allmanová Z, Ferenčík M. Soil compaction of various Central European forest soils caused by traffic of forestry machines with various chassis. For Syst. 2015;24(3):1–10. https://doi.org/10.5424/fs/2015243-07541.
Cambi M, Grigolato S, Neri F, Picchio R, Marchi E. Effects on soil physical characteristics due to forwarder operation: a case study in the Italian Alps. Croat J For Eng. 2016;37(2):233–9.
Eroğlu H, Sariyildiz T, Küçük M, Sancal E. The effects of different logging techniques on the physical and chemical characteristics of forest soil. Balt For. 2016;22(1):139–47.
Lang AJ, Cristan R, Aust WM, Bolding MC, Strahm BD, Vance ED, et al. Long-term effects of wet and dry site harvesting on soil physical properties mitigated by mechanical site preparation in coastal plain loblolly pine (Pinus taeda) plantations. Forest Ecol Manag. 2016;359:162–73. https://doi.org/10.1016/j.foreco.2015.09.034.
Venanzi R, Picchio R, Grigolato S, Latterini F. Soil and forest regeneration after different extraction methods in coppice forests. Forest Ecol Manag. 2019;454:117666. https://doi.org/10.1016/j.foreco.2019.117666.
Cambi M, Certini G, Fabiano F, Foderi C, Laschi A, Picchio R. Impact of wheeled and tracked tractors on soil physical properties in a mixed conifer stand. iForest. 2016;9:89–94. https://doi.org/10.3832/ifor1382-008.
Labelle ER, Kammermeier M. Above- and belowground growth response of Picea abies seedlings exposed to varying levels of soil relative bulk density. Eur J For Res. 2019;138(4):705–22. https://doi.org/10.1007/s10342-019-01201-6.
Majnounian B, Jourgholami M. Effects of rubber-tired cable skidder on soil compaction in Hyrcanian forest. Croat J For Eng. 2013;34(1):123–35.
Naghdi R, Solgi A. Effects of skidder passes and slope on soil disturbance in two soil water contents. Croat J For Eng. 2014;35(1):73–80.
Marchi E, Picchio R, Mederski PS, Vusić D, Perugini M, Venanzi R. Impact of silvicultural treatment and forest operation on soil and regeneration in Mediterranean Turkey oak (Quercus cerris, L.) coppice with standards. Ecol Eng. 2016;95:475–84. https://doi.org/10.1016/j.ecoleng.2016.06.084.
Venanzi R, Picchio R, Piovesan G. Silvicultural and logging impact on soil characteristics in chestnut (Castanea sativa Mill.) Mediterranean coppice. Ecol Eng. 2016;92:82–9. https://doi.org/10.1016/j.ecoleng.2016.03.034.
Solgi A, Najafi A, Ezzati S, Fereňcík M. Assessment of ground-based skidding impacts on the horizontally rate and extent of soil disturbance along the margin of the skid trail. Ann For Sci. 2016;73:513–22. https://doi.org/10.1007/s13595-016-0544-7.
Jourgholami M, Majnounian B. Traditional mule logging method in Hyrcanian Forest: a study of the impact on forest stand and soil. J Forestry Res. 2013;24(4):755–8. https://doi.org/10.1007/s11676-013-0370-9.
Jaafari A, Najafi A, Zenner EK. Ground-based skidder traffic changes chemical soil properties in a mountainous Oriental beech (Fagus orientalis Lipsky) forest in Iran. J Terramechanics. 2014;55:39–46. https://doi.org/10.1016/j.jterra.2014.06.001.
Kleibl M, Klvač R, Lombardini C, Porhaly J, Spinelli R. Soil compaction and recovery after mechanized final felling of Italian coastal pine plantations. Croat J For Eng. 2014;35(1):63–71.
Hosseini SA, Nasiri M, Akbarimehr M. Skidders traffic assessment on forest soil properties. Int J Civ Eng. 2015;13(3):372–7.
Zhou X, Zhou Y, Zhou C, Wu Z, Zheng L, Hu X, et al. Effects of cutting intensity on soil physical and chemical properties in a mixed natural forest in southeastern China. Forests. 2015;6(12):4495–509.
Naghdi R, Solgi A, Zenner EK, Tsioras PA, Nikooy M. Soil disturbance caused by ground-based skidding at different soil moisture conditions in Northern Iran. Int J For Eng. 2016;29(1):169–78. https://doi.org/10.1080/14942119.2016.1234196.
Ozturk T. The effects on soil compaction of timber skidding by tractor on skid road in plantation forest in Northern Turkey. Šumarski List. 2016;9–10:485–91.
Proto AR, Macrì G, Sorgonà A, Zimbalatti G. Impact of skidding operations on soil physical properties in southern Italy. Contemporary Eng Sci. 2016;9(23):1095–104. https://doi.org/10.12988/ces.2016.68132.
Abdi E, Moghadamirad M, Elyas Hayati E, Jaeger D. Soil hydrophysical degradation associated with forest operations. Forest Sci Technol. 2017;13(4):152–7. https://doi.org/10.1080/21580103.2017.1387611.
Cudzik A, Brennensthul M, Białczyk W, Czarnecki J. Damage to soil and residual trees caused by different logging systems applied to late thinning. Croat J For Eng. 2017;38(1):83–95.
Jourgholami M, Etehadi AM. Effectiveness of sawdust and straw mulching on postharvest runoff and soil erosion of a skid trail in a mixed forest. Ecol Eng. 2017;109(A):15–24. https://doi.org/10.1016/j.ecoleng.2017.09.009.
Macrì G, De Rossi A, Papandrea S, Micalizzi F, Russo D, Settineri G. Evaluation of soil compaction caused by passages of farm tractor in a forest in southern Italy. Agron Res. 2017;15(2):478–89.
Malvar MC, Silva FC, Prats SA, Vieira DCS, Coelho COA, Keizer JJ. Short-term effects of post-fire salvage logging on runoff and soil erosion. For Ecol Manag. 2017;400:555–67. https://doi.org/10.1016/j.foreco.2017.06.031.
Sealey LL, Van Rees KCJ. Influence of skidder traffic on soil bulk density, aspen regeneration, and vegetation indices following winter harvesting in the Duck Mountain Provincial Park, SK. For Ecol Manag. 2019;437:59–69. https://doi.org/10.1016/j.foreco.2019.01.017.
Badraghi A, Erler J, Hosseini SAO, Lang R. Evaluation of animal logging in the mixed broadleaved mountain forest: Economic and environmental impacts. J For Sci. 2018;64(6):251–9. https://doi.org/10.17221/18/2018-JFS.
Hittenbeck J. Estimation of trafficable grades from traction performance of a forwarder. Croat J For Eng. 2013;34(1):71–81.
Cambi M, Paffetti D, Vettori C, Picchio R, Venanzi R, Marchi E. Assessment of the impact of forest harvesting operations on the physical parameters and microbiological components on a Mediterranean sandy soil in an Italian stone pine stand. Eur J For Res. 2017;136:205–15.
Łukasik W, Kubiesa P, Staszewski T. Erosion processes initialized by use of heavy equipment in mountain forests of the Wilczy Potok catchment, Silesian Beskids. Arch Environ Prot. 2016;42(1):80–6. https://doi.org/10.1515/aep-2016-0010.
Picchio R, Latterini F, Mederski PS, Venanzi R, Karaszewski Z, Bembenek M, et al. Comparing accuracy of three methods based on the GIS environment for determining winching areas. Electronics. 2019;8(1):53. https://doi.org/10.3390/electronics8010053.
Duka A, Grigolato S, Papa I, Pentek T, Poršinsky T. Assessment of timber extraction distance and skid road network in steep karst terrain. iForest. 2017;10(6):886–94. https://doi.org/10.3832/ifor2471-010.
Masumian A, Naghdi R, Zenner EK. Effectiveness of water diversion and erosion control structures on skid trails following timber harvesting. Ecol Eng. 2017;105:370–8. https://doi.org/10.1016/j.ecoleng.2017.05.017.
Dionisio LFS, Schwartz G, Lopes JDC, Oliveira FDA. Growth, mortality, and recruitment of tree species in an Amazonian rainforest over 13 years of reduced impact logging. Forest Ecol Manag. 2018;430:150–6.
• Rivett SL, Bicknell JE, Davies ZG. Effect of reduced-impact logging on seedling recruitment in a neotropical forest. Forest Ecol Manag. 2016;367:71–9. https://doi.org/10.1016/j.foreco.2016.02.022The paper provides a detailed overview of seedling growth and survival of regeneration in tropical rainforest, related to reduced impact logging (RIL) applications. One of the key conclusions was that the forestry practices associated with RIL had little effect on the natural regeneration rates of commercially valuable tree species in logged neotropical forests.
Beaudet M, Angers VA, Messier C. Seedbed proportions in and outside skid trails: temporal variation following selection cutting in northern hardwood forests. Forest Ecol Manag. 2014;318:151–7. https://doi.org/10.1016/j.foreco.2014.01.001.
Picchio R, Mercurio R, Venanzi R, Gratani L, Giallonardo T, Lo Monaco A, et al. Strip clear-cutting application and logging typologies for renaturalization of pine afforestation – a case study. Forests. 2018;9:366. https://doi.org/10.3390/f9060366.
Premer MI, Froese RE. Incidental effects of cut-to-length harvest systems and residue management on Populus tremuloides (Michx.) regeneration and yield. For Sci. 2018;64(4):442–51. https://doi.org/10.1093/forsci/fxx019.
Gavinet J, Vilagrosa A, Chirino E, Granados ME, Vallejo VR, Prévosto B. Hardwood seedling establishment below Aleppo pine depends on thinning intensity in two Mediterranean sites. Ann For Sci. 2015;72:999–1008. https://doi.org/10.1007/s13595-015-0495-4.
Schweitzer CJ, Dey DC. Logging intensity impact on small oak seedling survival and growth on the Cumberland Plateau in Northeastern Alabama. South J Appl For. 2013;37(2):113–21.
Stańczykiewicz A, Szewczyk G, Kulak D. Damage to advance growth resulting from timber harvesting during final cuttings. Balt For. 2015;21(1):144–51.
García-Orenes F, Arcenegui V, Chrenková K, Mataix-Solera J, Moltó J, Jara-Navarro AB, et al. Effects of salvage logging on soil properties and vegetation recovery in a fire-affected Mediterranean forest: a two year monitoring research. Sci Total Environ. 2017;586:1057–65. https://doi.org/10.1016/j.scitotenv.2017.02.090.
Morgan P, Moy M, Droske CA, Lewis SA, Lentile LB, Robichaud PR, et al. Vegetation response to burn severity, native grass seeding, and salvage logging. Fire Ecol. 2014;10:31–58. https://doi.org/10.4996/fireecology.1102031.
Fernández C, Vega JA. Effects of mulching and post-fire salvage logging on soil erosion and vegetative regrowth in NW Spain. Forest Ecol Manag. 2016;375:46–54. https://doi.org/10.1016/j.foreco.2016.05.024.
Stańczykiewicz A, Sowa JM, Szewczyk G. Damage to trees and regeneration as a result of motor-manual timber harvesting using equipment aggregated with farm tractors. Sylwan. 2011;155(2):129–37.
Badraghi N, Erler J, Hosseini SAO. Residual damage in different ground logging methods alongside skid trails and winching strips. J For Sci. 2015;61(12):526–34.
Picchio R, Magagnotti N, Alessandro Sirna A, Spinelli R. Improved winching technique to reduce logging damage. Ecol Eng. 2011;47:83–6. https://doi.org/10.1016/j.ecoleng.2012.06.037.
Picchio R, Tavankar F, Bonyad A, Mederski PS, Venanzi R, Nikooy M. Detailed analysis of residual stand damage due to winching on steep terrains. Small-Scale For. 2019;18(2):255–77. https://doi.org/10.1007/s11842-019-09417-5.
Marchi E, Chung W, Visser R, Abbas D, Nordfjell T, Mederski PS, et al. Sustainable Forest Operations (SFO): a new paradigm in a changing world and climate. Sci Total Environ. 2018;634:1385–97. https://doi.org/10.1016/j.scitotenv.2018.04.084.
Sirén M, Hyvönen J, Surakka H. Tree damage in mechanized uneven-aged selection cuttings. Croat J For Eng. 2015;36(1):33–42.
Behjou FK. Effects of wheeled cable skidding on residual trees in selective logging in Caspian forests. Small-Scale For. 2014;13:367–76. https://doi.org/10.1007/s11842-013-9259-x.
Behjou FK, Mollabashi OG. Selective logging and damage to unharvested trees in a Hyrcanian forest of Iran. BioResources. 2012;7(4):4867–74.
Grzywiński W, Turowski R, Naskrent B, Jelonek T, Tomczak A. The effect of season of the year on the frequency and degree of damage during commercial thinning in black alder stands in Poland. Forests. 2019;10(8):668. https://doi.org/10.3390/f10080668.
Bembenek M, Giefing DF, Karaszewski Z, Mederski PS, Szczepańska-Álvarez A. Tree damage in lowland spruce stands caused by early thinnings. Sylwan. 2013;157(10):747–53.
Bembenek M, Giefing DF, Karaszewski Z, Mederski PS, Szczepańska-Álvarez A. Tree damage in lowland spruce stands because of late thinning. Sylwan. 2013;157(12):892–8.
Bakinowska E, Mederski PS, Szczepańska-Alvarez A, Karaszewski Z, Bembenek M. The paralel application of two probability models, logit and probit, for the accurate analysis of spruce timber damage due to thinning operations. Drewno. 2016;59(197):49–59. https://doi.org/10.12841/wood.1644-3985.C16.06.
Tavankar T, Bonyad AE, Marchi E, Venanzi R, Picchio R. Effect of logging wounds on diameter growth of beech (Fagus orientalis Lipsky) trees following selection cutting in Caspian forest of Iran. Nz J Forestry Sci. 2015;45(19):1–7. https://doi.org/10.1186/s40490-015-0052-9.
Karaszewski Z, Giefing DF, Mederski PS, Bembenek M, Dobek A, Stergiadou A. Stand damage when harvesting timber using a tractor for extraction. For Res Papers. 2013;74(1):27–34.
• Mihelič M, Spinelli R, Poje A. Intensifying the management of protection forests in the Alps. Drewno. 2018;61(201):23–37. https://doi.org/10.12841/wood.1644-3985.D03.07The paper provides a detailed overview about cable yarding in a protection forest, under conditions that are representative of the challenges encountered when negotiating this forest type. The information collected with this study is highly suggestive and may provide a solid starting platform for exploring the increasingly important issue of protection forest management, especially in the face of the effects of climate change.
Šņepsts G, Bigača Z, Desaine I, Jansons J, Donis J, Strēlnieks K, et al. Characteristics of damages in Norway spruce stands. Res Rural Dev. 2018;1:65–71. https://doi.org/10.22616/rrd.24.2018.010.
Allman M, Allmanová Z, Jankovský M, Ferenčík M, Messingerová V. Damage of the remaining stands caused by various types of logging technology. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis. 2016;64(2):379–85.
Tavankar F, Majnounian B, Bonyad AE. Felling and skidding damage to residual trees following selection cutting in Caspian forests of Iran. J For Sci. 2013;59(5):196–203.
Jourgholami M. Operational impacts to residual stands following ground-based skidding in Hyrcanian Forest, northern Iran. J For Res. 2012;23(2):333–7. https://doi.org/10.1007/s11676-012-0261-5.
Tolosana E, Spinelli R, Aminti G, Laina R, López-Vicens I. Productivity, efficiency and environmental effects of whole-tree harvesting in Spanish coppice stands using a drive-to-tree disc saw feller-buncher. Croat J For Eng. 2018;39(2):163–72.
Medjibe VP, Putz FE, Starkey MP, Ndouna AA, Memiaghe HR. Impacts of selective logging on above-ground forest biomass in the Monts de Cristal in Gabon. Forest Ecol Manag. 2011;262(9):1799–806. https://doi.org/10.1016/j.foreco.2011.07.014.
Funding
Presented research was supported financially by the Italian Ministry for Education, University and Research (MIUR) (Law 232/2016, Italian University Departments of Excellence) – UNITUS-DAFNE WP3. This publication was co-financed within the framework of the Polish Ministry of Science and Higher Education’s programme: “Regional Initiative Excellence” in the years 2019–2022, Project No. 005/RID/2018/19. Financial support was received by Assoc. Prof. Piotr S. Mederski.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
Rodolfo Picchio, Piotr S. Mederski and Farzam Tavankar declare that they have no conflict of interest.
Human and Animal Rights and Informed Consent
This article does not contain any studies with human or animal subjects performed by any of the authors.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
This article is part of the Topical Collection on Forest Engineering
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Picchio, R., Mederski, P.S. & Tavankar, F. How and How Much, Do Harvesting Activities Affect Forest Soil, Regeneration and Stands?. Curr Forestry Rep 6, 115–128 (2020). https://doi.org/10.1007/s40725-020-00113-8
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40725-020-00113-8