Abstract
Optical frequency combs in microresonators (microcombs) have a wide range of applications in science and technology, due to its compact size and access to considerably larger comb spacing. Despite recent successes, the problems of self-starting, high mode efficiency as well as high output power have not been fully addressed for conventional soliton microcombs. Recent demonstration of laser cavity soliton microcombs by nesting a microresonator into a fiber cavity, shows great potential to solve the problems. Here we study the dissipative soliton generation and interaction dynamics in a microresonator-filtered fiber laser in both theory and experiment. We bring theoretical insight into the mode-locking principle, discuss the parameters effect on soliton properties, and provide experimental guidelines for broadband soliton generation. We predict chirped bright dissipative soliton with flat-top spectral envelope in microresonators with normal dispersion, which is fundamentally forbidden for the externally driven case. Furthermore, we experimentally achieve soliton microcombs with large bandwidth of ~10 nm and high mode efficiency of 90.7%. Finally, by taking advantage of an ultrahigh-speed time magnifier, we study the real-time soliton formation and interaction dynamics and experimentally observe soliton Newton’s cradle. Our study will benefit the design of the novel, high-efficiency and self-starting microcombs for real-world applications.
Similar content being viewed by others
Introduction
Optical frequency combs (OFCs) have been the cornerstones and key enabling technologies for many scientific breakthroughs in precision frequency metrology1,2, ultra-stable time keeping3,4, coherent comb spectroscopy5,6 and other fields7,8,9,10. Enormous progress has been made towards conventional OFCs based on self-starting mode-locked lasers, where efficient laser gain provides the comb energy. On the other hand, the emerging dissipative Kerr soliton (DKS) microcombs11,12,13,14 have recently served as a promising complement due to its compact size and access to considerably larger comb spacing. However, fundamentally limited by external drive configuration and low coupling rate of the microresonators with high quality (Q) factor, the achieved DKS microcombs exhibit low output power and low mode efficiency theoretically limited to 5% for bright DKS15. Therefore, it is challenging to directly apply the microcombs for applications demanding high comb power16,17. Besides, the bi-stability and strong thermal nonlinearity prohibit the self-starting of DKS microcombs, and complex active electronics is required for soliton initiation and stabilization12,18,19. Despite the efforts of nonlinear self-injection locking20,21, cascaded Brillouin-Kerr process22, synchronous pumping23, dark-soliton combs24 and impedance matching25, self-starting microcombs with high output power and high mode efficiency are still challenging.
Recent pioneering work26 reports soliton microcombs in a microresonator-filtered fiber laser27, which provides the unique opportunity to realize laser cavity soliton (LCS) microcombs with advantages of self-starting, theoretical high mode efficiency up to 96%26 and no need of a tunable single-frequency laser. From the perspective of external driving DKS, LCS is formed through synchronous pumping23 where the driven pulse comes from the DKS itself in the microresonator. Despite the advantages presented in this solo case, the soliton mode-locking principle and corresponding dynamics in microresonator-filtered fiber lasers have not been studied especially in the experiment, mainly due to the challenge of measuring ultrahigh repetition rate mode-locked pulses in real time. Fortunately, the powerful time magnifier system can help to surpass the electronic limits and study microresonator dynamics at ultrahigh repetition rates of several tens of GHz or more28,29,30. Being capable to characterize non-repetitive and arbitrary waveforms in real time with sub-picosecond temporal resolution in a single shot31,32,33,34, the time magnifier system represents an ideal tool to study the soliton dynamics, which helps to gain insight into the underlying physics and achieve low-noise microcombs in microresonator-filtered fiber lasers.
Here we theoretically and experimentally study the dissipative soliton generation and real-time dynamics in a fiber laser nested by a high-Q fiber Fabry–Pérot (FFP) microresonator. We provide new theoretical insight into the mode-locking principle and provide experimental guidelines for stable soliton with broad bandwidth. Apart from anomalous group velocity dispersion (GVD) induced solitons, we predict chirped bright soliton with flat-top spectral envelope from normal-GVD microresonators, in contrast to the dark soliton in the externally driven system24. Subsequently, according to our proposed experimental guidelines, we experimentally achieve self-starting soliton microcombs with broad 3-dB bandwidth of ~10 nm and repetition rates from ~10 GHz to ~100 GHz. The soliton output power is as high as ~12 mW with mode efficiency up to 90.7%. Finally, by taking advantage of an ultrahigh-speed time magnifier, we study the real-time dynamics of soliton formation and interaction with coexisting continuous-wave (CW) components in microresonator-filtered fiber lasers. We observe soliton Newton’s cradle, where a single soliton elastically collides with a soliton molecule35,36,37, akin to macro-objects38,39,40. Our study will benefit the design of the novel, high-efficiency and self-starting microcombs for real-world applications.
Results
Mode-locking principle
Without loss of generality, the scheme for dissipative soliton generation in microresonator-filtered fiber lasers is shown in Fig. 1a. A high-Q FFP microresonator is embedded within a longer fiber cavity consisting of an Erbium-doped fiber amplifier (EDFA). The FP microresonator can also be replaced by a ring microresonator with add-drop ports as in26. The final oscillating modes are the eigen-frequencies for both the fiber laser cavity and the microresonator. By properly adjusting the cavity length, only single frequency is assumed to be resonant in each resonance of the microresonator (Fig. 1b) if the free spectral range (FSR) of the fiber cavity is larger than the linewidth of the microresonator, resulting in super-mode suppression.
According to the mode-locking principle of conventional fiber lasers, a saturable absorber (SA) is essential to suppress CW lasing and select pulses from background noise41,42,43. Moreover, proper pulse shaping mechanism is required to accomplish the pulse self-reproduction43. Although soliton is proved to be the solution of the microresonator-filtered lasers by both simulation and experiment, it still remains veiled how the soliton outbeats the CW components and eventually stabilizes itself. Here we theoretically and numerically find that the nested microresonator acts as two roles: (1) the SA; (2) the nonlinearity booster (see theory in Supplementary Information Section S1). Furthermore, intracavity pulses can be shaped via the balance between Kerr nonlinearity and either dispersion or strong intracavity spectral filtering, depending on both GVDs of the microresonator and the EDFA.
Nested microresonators with anomalous GVD are first studied theoretically to identify their roles. The dispersion, nonlinearity and gain dispersion in the EDFA, as well as intracavity band-pass filter (BPF), are neglected in this case to clearly show the pulse initiation and stabilization are mainly accomplished by the microresonator itself. The influence of the neglected parameters will be discussed in the next section. As shown in the subfigures (i) and (ii) of Fig. 1c, for anomalous-GVD microresonators, transmission of the lower branch with red detuning exhibits obvious SA effect: higher input power induces higher transmission thus lower loss for the fiber cavity. The subfigure (iii) of Fig. 1c demonstrates LCS self-starting process from amplified spontaneous emission (ASE). The pulse is firstly selected by the SA from amplified intensity noise, reaches the threshold of modulation instability (MI) and eventually evolves into a stable soliton. In other words, red-detuned microresonator favors soliton with high peak power and high transmission instead of CW solution44 (see Supplementary Information Section S2). The pulse shaping is accomplished by the balance between cavity-enhanced nonlinearity and anomalous GVD in the microresonator. The EDFA only provides the soliton gain without playing roles in pulse selecting and pulse shaping, which is verified by the identical soliton profiles and corresponding spectra before and after the microresonator [subfigures (iv) and (v) of Fig. 1c]. In contrast to the red-detuned case, this SA-like nonlinear transmission does not occur in the blue-detuned microresonator. Therefore, the fiber cavity length should be adjusted carefully to realize red detuning thus consequent mode-locking due to the detuning-dependent SA.
Besides, bright dissipative soliton is also feasible in this kind of lasers with inserted normal-GVD microresonators and an intracavity BPF, where the mode-locking principle is similar to all-normal-dispersion (ANDi) fiber lasers45 and flat-top spectrum can be achieved [the subfigure (iv) of Fig. 1d]. This provides a simple method for broadband comb with bright pulses in normal-GVD microresonators, which is not feasible in the conventional case24. Of note, the dispersion, nonlinearity and gain dispersion in the EDFA are also neglected here.
Similarly, the red-detuned normal-GVD microresonator acts as both the SA [subfigures (i) and (ii) of Fig. 1d] and the nonlinearity booster. In the subfigures (iv) and (v) of Fig. 1d, the pulse accumulates large nonlinearity phase shifts in the normal-GVD microresonator, simultaneously expands its spectrum and enlarges the pulse width, leading to highly chirped pulse. The BPF outside the microresonator performs the pulse shaping in both frequency and time domain due to the frequency-time mapping and accomplishes the pulse self-reproduction, in the same way of ANDi lasers. Additionally, soliton can also self-start from ASE as shown in the subfigure (iii) of Fig. 1d.
The acting roles of both SA and nonlinearity booster by red-detuned microresonators, are of advantage to achieve mode-locking with ultrahigh-repetition rate, which is out of reach for conventional mode-locked lasers due to: (1) conventional SAs usually have high saturation threshold, only response to pulse with high peak power and can not discriminate CW components and the low-energy pulses with ultrahigh repetition rate; (2) in conventional mode-locked lasers, low pulse energy results in insufficient Kerr nonlinearity for longitudinal mode interaction and mode-locking.
Experimental guidelines
Despite the theoretical mode-locking principle, many other parameters should be taken into account in the experiment for stable dissipative soliton with broad bandwidth. Since (1) nonlinearity is negligible for the EDFA due to the ultrahigh repetition rate induced low pulse energy; (2) the laser gain dispersion is almost fixed, we will focus on the dispersions of both the microresonator and EDFA, as well as bandwidth of the inserted BPF.
Figure 1e, f demonstrate dissipative soliton generation in a fiber laser nested by a microresonator with anomalous GVD and normal GVD, respectively. By varying the EDFA’s dispersion from anomalous to normal regime, mode-locked pulse width first narrows around near-zero EDFA GVD and then broadens, while the spectral bandwidth first broadens and then narrows. Therefore, broad soliton bandwidth can be achieved with near-zero EDFA GVD. In addition, similar to conventional DKS, small microresonator GVD benefits large soliton bandwidth, regardless of its sign (see Supplementary Information Section S3). Moreover, opposite signs of both microresonator and EDFA GVDs will lead to dispersive wave emission (see Supplementary Information Section S4)46 and cause soliton destabilization, which can be solved by an intracavity narrowband BPF to achieve stable soliton.
Overall, experimental guidelines can be summarized for stable dissipative soliton with broad bandwidth. (1) It is better to employ high-Q microresonators with large nonlinear parameters to lower the threshold, narrow the comb linewidth, lower the requirement of short fiber cavity length and suppress the super-modes. (2) It is beneficial to introduce microresonators with relatively high transmission through add-drop ports to lower the insertion loss. However, compromise should be made between the high Q and high transmission through add-drop ports. (3) Broad soliton bandwidth can benefit from small engineered GVDs for both the microresonator and the EDFA. (4) Compromise between the stable soliton bandwidth and intracavity spectral filtering should be made when the microresonator and EDFA exhibit different signs of GVD (see Supplementary Information Section S5).
Experimental generation of dissipative soliton
The experimental setup is shown in Fig. 2a. According to the above-proposed experimental guidelines, we carefully design the microresonator-filtered fiber laser to achieve dissipative soliton with broad bandwidth. (1) Our FFP microresonator is made of highly nonlinear fiber (HNLF) with a large nonlinear coefficient of 11.5 W−1·km−1. High Q factor of 2 × 107 is achieved with a resonance linewidth of 9.7 MHz (Fig. 2b), which is much smaller than the FSR of the large fiber cavity (~42 MHz), resulting in the suppression of super-modes since only single frequency can exist in each resonance of the microresonator. The FSR of the FFP microresonator is 10.18 GHz which can be ready for X-band applications. (2) The cold-cavity transmission of 7% (including the coupling loss from the input fiber end-face) is relatively large, leading to a pump threshold as low as 30 mW. (3) The GVD of the FFP microresonator is ~−2.5 fs2·mm−1 (see Materials and Methods) and the average dispersion of the EDFA is engineered to be as small as −4.4 fs2·mm−1. (4) A BPF (Semrock, NIR01-1570/3–25) with a flat-top profile of 8.9-nm bandwidth (3 dB) is introduced in the fiber cavity to adjust the lasing center wavelength. Other details of the experimental setup in Fig. 2a can be found in Methods.
At pump power of ~600 mW, dissipative soliton can self-start with random numbers ranging from 1 to 10, corresponding to comb repetition rate ranging from ~10 to ~100 GHz (see Supplementary Information Section S6). The output power after the microresonator is ~12 mW, which is almost one-order-magnitude higher compared with conventional DKS, and the mode efficiency is as high as 90.7%, approaching the theoretical limit of 96%26.
Figures 2c and 3 show examples of single soliton and perfect soliton crystals with 2, 4 and 6 FSRs, respectively. Other multiple soliton states can be found in the Supplementary Information Section S7. The mode-locked states are confirmed by the clear radio frequency (RF) beat notes of the comb repetition rate (insets of Figs. 2c and 3a, b). In particular, we measure the single sideband (SSB) phase noise of the single soliton as shown in Fig. 2d. The SSB phase noises at 10 kHz, 100 kHz, and 1 MHz offset frequencies are −97 dBc·Hz−1, −117 dBc·Hz−1, and −137 dBc·Hz−1, respectively. The large phase noises below 1 kHz offset frequencies, which can be significantly reduced by active feedback loops, are attributed to the soliton relative intensity noise (RIN) resulting from the active gain fiber and the noise coupling from the environment, while the peak at 70 kHz comes from the RIN of the EDFA pump (Fig. 2e). The fundamental comb linewidth is <32 mHz (Fig. 2f), which is 38 dB better than the conventional external cavity diode lasers (ECDLs), due to the ultrahigh Q induced laser phase noise suppression. Even with narrower comb linewidth, the soliton phase noise is at the same level of the results in an on-chip microresonator pumped by an ECDL47, indicating detuning noise mainly contributes to the soliton phase noise.
Moreover, the perfect soliton crystals and corresponding soliton numbers are also confirmed by the real-time pulse evolution with clean background (right panels of Fig. 3a–c) using the time magnifier, which can be viewed as a powerful and ultrahigh-speed optical oscilloscope (see Methods and Supplementary Information Section S8 for details). The recording time window of the time magnifier is determined to be ~285 ps from the pump pulse width. The peak voltage difference of the solitons along the fast time axis is due to the non-uniform responsivity inside the recording time window, which is caused by the wavelength-dependent four-wave-mixing (FWM) efficiency (see Supplementary Information Section S8). The calibrated pulses with similar intensities [insets of Fig. 3 (right panels)] by the responsivity curve (Supplementary Fig. S8d in Supplementary Information) as well as the equal temporal distances, verify the perfect soliton crystals with high-contrast and smooth spectra. Besides, owing to the imperfect synchronization between the soliton signal and the pump pulses of the time magnifier (see Supplementary Information S8), the measured soliton intensity evolution along the slow time axis exhibits intensity variation and discontinuity when the same soliton gradually walks off from the recording time window.
Benefiting from the careful dispersion engineering around zero dispersion, the 3-dB bandwidth of the spectra output from the microresonator is ~10 nm, which agrees excellently with the simulated results (dashed black lines) and represents three times larger than the reported result26. The enlarged spectrum after the FFP microresonator indicates the boosted nonlinearity induced spectrum broadening and soliton shaping inside the microresonator, which validates the roles of the microresonator according to the above-mentioned mode-locking principle. Further increase of the soliton bandwidth can result from a broadband intracavity BPF and will eventually be limited by the gain bandwidth.
Interestingly, a single comb line stands out from the soliton spectral envelope and always locates around the short-wavelength edge of the BPF (see the noise floor of the spectra before the microresonator). However, no transmission spike is found for the BPF (see Supplementary Information Section S9). We attribute the standing-out comb line with high intensity to the phase shift at the BPF edges48,49,50,51 (see Supplementary Information Section S9). In contrast to the red-detuned soliton comb lines, the BPF induced CW peak is believed to be blue detuned52 resulting from the phase shift. The CW peak does not belong to the soliton spectrum since it locates in the middle of two adjacent soliton comb lines. In addition, the coexisting CW component can cause soliton long-range interaction with each other and lead to perfect soliton crystal generation in Fig. 353,54,55,56,57,58, without the help of avoid mode crossings since our FFP microresonator is single-mode. The interleaved weak-intensity comb lines (peaks indicated by orange solid circles in the insets of Fig. 3) are caused by cross phase modulation (XPM) between the soliton and the coexisting CW component, which results in the same comb repetition rate with the soliton. By including the XPM effect from the single blue-detuned CW peak in the simulation, we achieve the XPM induced combs coexisting with the main soliton combs (see Supplementary Information Section S10), which agrees with the experimental results.
As for the long-term stability, soliton can keep stable for tens of minutes in the experiment. Due to the detuning variation resulting from the optical path length change in the large fiber cavity, the soliton repetition rate fluctuates in a range of 20 kHz for the 2-FSR microcombs, as shown in the inset of Fig. 3a (left panel). We believe passive and active control methods can be implemented to improve the long-term stability (see Supplementary Information Section S11).
Dynamics of dissipative soliton formation and interaction
Dissipative soliton in microresonator-filtered fiber lasers is fundamentally different from both the conventional mode-locked fiber lasers and externally driven microresonators. To gain more insight into the underlying physics, we study the soliton formation and interaction dynamics in both frequency domain and time domain. Since the pulse repetition rate is >10 GHz, the traditional soliton dynamics monitoring by dispersive Fourier transform59,60 is not feasible due to the insufficient time stretch limited by the pulse period. Instead, we use the powerful time magnifier system to study soliton dynamics in the presence of CW components induced by the phase shift at BPF edges.
Figure 4a–c record the spectrum evolution from CW laser to soliton by manually and monotonously increasing the cavity length via the delay line. Six typical states are recorded when the delay line is paused at six positions. As shown in state I (Fig. 4a), a CW component lases first around the short-wavelength edge of the BPF (1542.4 nm), although it does not belong to the final soliton. In state II, another CW component stands out around the long-wavelength edge of the BPF (1549.7 nm), while primary comb lines are generated from non-degenerate FWM process. Thereafter sub-combs are generated near the primary combs (state III) through either degenerate or non-degenerate FWM process. In state IV, more combs start to lase due to the MI. Simultaneously, noisy pulses can be formed (see Supplementary Information Section S12), which is a precursor for mode locking. However, the pulses can not keep stable since they are in the unstable MI regime.
When the soliton comb lines are red detuned, the spectrum eventually evolves into a sech2 profile (state V), with coexisting multi-frequency CW components (inset of Fig. 4b). Nonetheless, the comb intensity fluctuation and the broadband RF beat note (inset of Fig. 4b) of the repetition rate indicate the incoherent comb lines and unstable mode-locking. While in time domain (Fig. 4d), the solitons sit on a noisy background, interact and exchange energy with it, leading to fluctuating soliton temporal distances and unstable repetition rate. In the retarded time frame of soliton, the weak-intensity longer pulses in the background do not move at the same speed with the soliton. In fact, the weak-intensity longer pulses experience much smaller Kerr nonlinearity than the solitons so that they move faster than the solitons. The unstable mode-locking state is attributed to the strong perturbation from XPM effect between the coexisting CW components and soliton, which is well reproduced by simulation in Fig. 4f.
By further fine adjusting the delay line, the multiple CW components are suppressed and only single-frequency lasing coexists with the two solitons (state VI, Fig. 4c). In time domain (Fig. 4e), the solitons stably coexist with a clean background and keep the temporal distance between each other. The narrowband RF beat note of the repetition rate indicates the stable mode-locking, as shown in the inset of Fig. 3a (left panel). The coexisting single CW peak can interact with soliton and generate additional combs through the XPM effect, which is verified by the inset of Fig. 3a (left panel) and the simulation results in Fig. 4g. However, the soliton stability is not affected due to the alleviated perturbation from the coexisting single CW peak and the strong SA effect from the large red detuning (Fig. 1c).
Besides, in state VI, we suddenly block the fiber laser cavity and in Fig. 4h record the interaction of six solitons circulating in the microresonator or >1400 solitons in the large fiber cavity. As shown in Fig. 4h in the retarded time frame of soliton B, at moment t1 soliton A moves towards a soliton molecule where soliton B and soliton C bind together and move at the same group velocity. As soliton A move closer, it starts to interact with the soliton molecule. At time t2, soliton A collides elastically with the soliton molecule and binds together with soliton B, forming a new soliton molecule. During the collision period, soliton B does not change the group velocity while soliton C gains the soliton A’s group velocity and starts to move away from soliton B.
This collision scenario is similar to the Newton’s cradle in classical mechanics38,39,40, where the first ball moves in one direction and collides with another two balls remaining at rest with the same mass, leading to the energy and momentum exchange between the first and the third ball. As a consequence, the first ball stops moving and remains at rest together with the second ball, while the third ball starts to move at the same speed with the first ball before the collision. While in microresonator-filtered fiber lasers, solitons are identical with the same pulse duration and pulse intensity. In this dissipative system, the conservation of velocity difference between the single soliton and the soliton molecule before and after the collision, is mainly owed to the fixed stationary solutions governed by the system37.
Two sets of this soliton Newton’s cradle are found in the microresonator and they independently accomplish their corresponding elastic collision at the same time, mainly due to the large temporal distance and weak interaction. The elastic collision self-reproduces over time due to the cavity boundary conditions, which can be seen more clearly in the video in the Supplementary Information.
The soliton Newton’s cradle can be achieved in a limited range of parameters in the microresonator-filtered fiber lasers, among many other possibilities for collision between three solitons36. In our case, the soliton molecule with non-zero binding energy is mainly attributed to the soliton interaction mediated by the coexisting CW component53,55,61. Compared to the single soliton, the soliton molecule with modulated spectrum has a different group velocity, leading to the walk-off at a speed of ~2000 m·s−1 and eventually the collision with the single soliton. Benefitting from the fast interaction dynamics, the microresonator-filtered fiber lasers can act as a good test bench to study the soliton Newton’s cradle in other fields.
In summary of the real-time dynamics, the coexisting CW components not only influence the soliton stability and the mode efficiency, but also induce interesting soliton interaction such as perfect soliton crystal and soliton Newton’s cradle.
Discussion
In general, dissipative soliton generation and interaction in microresonator-filtered fiber lasers are quite similar to that in the mode-locked fiber lasers. The microresonator-based SA and pulse shaper, however, differentiate the microresonator-filtered fiber lasers from conventional fiber lasers and provide unique property of microcombs with ultrahigh-repetition rate. Compared with externally driven system, by introducing EDFAs and intracavity filters, the microresonator-filtered fiber lasers add more freedoms to adaptive control the soliton properties, such as self-starting, repetition rate26 and spectral envelope. Besides, the intracavity spectral filtering provides a feasible method to generate bright broadband soliton with normal-GVD microresonators. However, every coin has two sides. The additional freedoms might cause the problem of soliton stability, especially the long-term stability, owing to the environmental perturbation to the long-length fiber cavity thus the detuning (see Supplementary Information Section S11). Of course, this property in turn provides another route for optical sensing using the solitons in microresonator-filtered fiber lasers.
In conclusion, we comprehensively study the mode-locking in microresonator-filtered fiber lasers, including the principle, experimental guidelines and dynamics of soliton generation and interaction. Two roles of the microresonator for mode-locking, the SA and the nonlinearity booster, are identified in both theory and experiment, as well as the pulse shaping mechanism. Theoretical analysis shows that both GVDs of the microresonator and EDFA are important for the soliton mode-locking principle and properties. Chirped bright dissipative soliton with flat-top spectral envelope in normal-GVD microresonators is predicted, in contrast to the dark soliton for externally driven system. Experimental guidelines are given and soliton microcombs with 3-dB bandwidth of ~10 nm and repetition rates ranging from ~10 GHz to ~100 GHz are achieved. High soliton output power of ~12 mW with mode efficiency up to 90.7%, is also obtained. Soliton phase noise comparable to the on-chip platforms is demonstrated with −97 dBc·Hz−1, −117 dBc·Hz−1, and −137 dBc·Hz−1 at 10 kHz, 100 kHz, and 1 MHz offset frequencies, respectively. Real-time observations of soliton formation and interaction dynamics including the soliton Newton’s cradle with coexisting CW components are demonstrated via an ultrahigh-speed time magnifier. Our study will benefit the design of the novel, high-efficiency and self-starting microcombs for real-world applications.
Materials and methods
Experimental setup and measurement
Our high-Q FFP microresonator is fabricated through three steps: (i) commercial HNLF (OFS 80412m2) is carefully cleaved and encapsuled in a ceramic fiber ferrule; (ii) both fiber ends are mechanically polished to sub-wavelength smoothness62; (iii) both fiber ends are coated with optical dielectric Bragg mirror (inset of Fig. 2a) with reflectivity over 99.5% from 1530 to 1570 nm. The FFP microresonator length is 10 mm, and the roundtrip length is 20 mm. The GVD of the FFP microresonator is 2.0 ± 1.0 ps·nm−1·km−1 (with a small dispersion slope of 0.019 ± 0.004 ps·nm−2·km−1) for efficient nonlinear spectral broadening. The full width at half maximum (FWHM) linewidth of the microresonator is measured via frequency scanning calibrated by an unbalanced Mach–Zehnder interferometer (MZI) with a FSR of 1 MHz (see Supplementary Information Section S13). The transmission of the cold FFP microresonator is measured through Pound–Drever–Hall (PDH) locking technique. The microresonator is temperature controlled with a resolution of 10 mK.
As for the EDFA, the dispersion for the passive sing-mode fiber (~3.4 m) and the Erbium-doped fiber (~1 m) are −23 fs2·mm−1 and 59 fs2·mm−1 63 at ~1550 nm, resulting in small, averaged dispersion of −4.4 fs2·mm−1. In order to shorten the length of the large fiber cavity and ensures low coupling loss, free-space components are introduced to couple the light into and out from the FFP microresonator. We believe all-fiber integration is feasible due to the compatibility between the FFP microresonator and other fiber components. The home-built EDFA is not temperature controlled but is enclosed in a box made of acrylic sheet and is largely isolated from the lab environment, including the phonons and heat change through the air. The long-term temperature variation in the lab is ±1 K. The optical isolator ensures the unidirectional lasing of the fiber cavity. A delay line is used to adjust the length-matching between the large fiber cavity and the FFP microresonator, as well as the relative position of the oscillating modes within the FFP microresonator.
The soliton phase noise is measured by injecting the combs into a fast photodetector (PD) (>10 GHz bandwidth), dividing the 10.18-GHz signal by 8 times, mixing the divided signal with a down-converter and detecting the down-converted signal with a phase noise analyzer (PNA).
A self-heterodyne frequency discriminator using a fiber-based unbalanced MZI and a balanced photodetector (BPD) is employed to measure the laser phase noise and fundamental linewidth. One arm of the unbalanced MZI is made of 250-m-long single-mode fiber, while the other arm consists of an acousto-optic frequency shifter with frequency shift of 200 MHz and a polarization controller for high-voltage output. The FSR of the unbalanced MZI is 0.85 MHz. The two 50:50 outputs of the unbalanced MZI are connected to a BPD (PDB570C, Thorlabs) with a bandwidth of 400 MHz to reduce the impact of detector intensity fluctuations. The balanced output is then analyzed by a PNA. Fundamental linewidth is calculated from the white noise floor of the measured SSB frequency noise spectra. The minimum fundamental linewidth that can be measured by this frequency discriminator is below 10 mHz.
The RF beat notes of comb repetition rate in the insets of Fig. 2d, e are measured by injecting all the comb lines into an electro-optic intensity modulator modulated at 20 GHz. Each comb line will generate sidebands at 20 GHz and its harmonics. For the 2-FSR combs in Fig. 2d, the beat note of the comb repetition rate at 20.36 GHz is down-converted to the beat note between the 1st-order sideband and the adjacent comb lines at 0.36 GHz. For the 4-FSR combs in Fig. 2e, the beat note of the comb repetition rate at 40.72 GHz is down-converted to the beat note between the 2nd-order sideband and the adjacent comb lines or between the two 1st-order sidebands from adjacent comb lines at 0.72 GHz. For the 6-FSR combs, the intensity of 3rd-order sideband is too weak so that we cannot measure the down-converted beat note with good signal-to-noise ratio. The down-converted beat note is detected by a fast PD and analyzed by an electrical spectrum analyzer (Agilent E4407B).
Time magnifier setup
The pump of the time magnifier is generated from a 50-MHz mode-locked fiber laser (Menlo C-fiber), which is chirped by around 400-m of Corning DCM-D-080-04 and amplified by a C-band EDFA. The signals under test are chirped by 200-m of Corning DCM-D-080-04 and the output dispersion is provided by 15 km of the same fiber. The final optical signal is pre-amplified by an L-band EDFA and then measured by a 38-GHz-bandwidth photodetector (Newfocus 1474 A) and subsequently digitized by a 25-GHz real-time oscilloscope (Tektronix DPO72504D) with 100 Gs·s−1 sampling rate.
Data availability
The data that support the plots within this paper and the findings of this study are available from the corresponding authors upon reasonable request.
References
Huang, S. W. et al. A broadband chip-scale optical frequency synthesizer at 2.7 × 10−16 relative uncertainty. Sci. Adv. 2, e1501489 (2016).
Diddams, S. A. et al. An optical clock based on a single trapped 199Hg+ Ion. Science 293, 825–828 (2001).
Xin, M., Şafak, K. & Kärtner, F. X. Ultra-precise timing and synchronization for large-scale scientific instruments. Optica 5, 1564–1578 (2018).
Herman, D. et al. Femtosecond timekeeping: slip-free clockwork for optical timescales. Phys. Rev. Appl. 9, 044002 (2018).
Coddington, I., Newbury, N. & Swann, W. Dual-comb spectroscopy. Optica 3, 414–426 (2016).
Suh, M. G. et al. Microresonator soliton dual-comb spectroscopy. Science 354, 600–603 (2016).
Diddams, S. A. The evolving optical frequency comb. J. Optical Soc. Am. B 27, B51–B62 (2010).
Fortier, T. & Baumann, E. 20 years of developments in optical frequency comb technology and applications. Commun. Phys. 2, 153 (2019).
Newbury, N. R. Searching for applications with a fine-tooth comb. Nat. Photon. 5, 186–188 (2011).
Diddams, S. A., Vahala, K. & Udem, T. Optical frequency combs: coherently uniting the electromagnetic spectrum. Science 369, eaay3676 (2020).
Kippenberg, T. J. et al. Dissipative Kerr solitons in optical microresonators. Science 361, eaan8083 (2018).
Herr, T. et al. Temporal solitons in optical microresonators. Nat. Photon. 8, 145–152 (2014).
Gaeta, A. L., Lipson, M. & Kippenberg, T. J. Photonic-chip-based frequency combs. Nat. Photon.13, 158–169 (2019).
Pasquazi, A. et al. Micro-combs: a novel generation of optical sources. Phys. Rep. 729, 1–81 (2018).
Xue, X. X. et al. Microresonator Kerr frequency combs with high conversion efficiency. Laser Photon. Rev. 11, 1600276 (2017).
Hensley, J. M. et al. Proceedings of SPIE 10638, Ultrafast Bandgap Photonics III (USA: SPIE, 2018).
Shchekin, A. et al. Coherent anti-Stokes Raman scattering under frequency comb excitation. Appl. Opt. 57, 632–638 (2018).
Yi, X. et al. Active capture and stabilization of temporal solitons in microresonators. Opt. Lett. 41, 2037–2040 (2016).
Guo, H. et al. Universal dynamics and deterministic switching of dissipative Kerr solitons in optical microresonators. Nat. Phys. 13, 94–102, https://doi.org/10.1038/nphys3893 (2017).
Shen, B. Q. et al. Integrated turnkey soliton microcombs. Nature 582, 365–369 (2020).
Xiang, C. et al. Laser soliton microcombs heterogeneously integrated on silicon. Science 373, 99–103 (2021).
Jia, K. P. et al. Photonic flywheel in a monolithic fiber resonator. Phys. Rev. Lett. 125, 143902 (2020).
Obrzud, E., Lecomte, S. & Herr, T. Temporal solitons in microresonators driven by optical pulses. Nat. Photon. 11, 600–607, https://doi.org/10.1038/nphoton.2017.140 (2017).
Xue, X. X. et al. Mode-locked dark pulse Kerr combs in normal-dispersion microresonators. Nat. Photon. 9, 594–600 (2015).
Xue, X. X., Zheng, X. P. & Zhou, B. K. Super-efficient temporal solitons in mutually coupled optical cavities. Nat. Photon. 13, 616–622 (2019).
Bao, H. L. et al. Laser cavity-soliton microcombs. Nat. Photon. 13, 384–389 (2019).
Peccianti, M. et al. Demonstration of a stable ultrafast laser based on a nonlinear microcavity. Nat. Commun. 3, 765 (2012).
Li, B. W. et al. Unveiling femtosecond rogue-wave structures in noise-like pulses by a stable and synchronized time magnifier. Opt. Lett. 44, 4351–4354 (2019).
Li, B. W. et al. Panoramic-reconstruction temporal imaging for seamless measurements of slowly-evolved femtosecond pulse dynamics. Nat. Commun. 8, 61 (2017).
Li, Y. N. et al. Real–time transition dynamics and stability of chip-scale dispersion-managed frequency microcombs. Light Sci. Appl. 9, 52 (2020).
Kolner, B. H. & Nazarathy, M. Temporal imaging with a time lens. Opt. Lett. 14, 630–632 (1989).
Li, B. W. et al. Temporal imaging for ultrafast spectral-temporal optical signal processing and characterization. IEEE J. Sel. Top. Quantum Electron. 27, 7600613 (2021).
Ryczkowski, P. et al. Real-time full-field characterization of transient dissipative soliton dynamics in a mode-locked laser. Nat. Photon. 12, 221–227 (2018).
Salem, R., Foster, M. A. & Gaeta, A. L. Application of space-time duality to ultrahigh-speed optical signal processing. Adv. Opt. Photon. 5, 274–317 (2013).
Grelu, P. & Akhmediev, N. Group interactions of dissipative solitons in a laser cavity: the case of 2+1. Opt. Express 12, 3184–3189 (2004).
Grelu, P. Dissipative soliton in a laser cavity: a novel concept in action. J. de. Phys. IV Fr. 135, 25–32 (2006).
Akhmediev, N. et al. Dissipative soliton interactions inside a fiber laser cavity. Optical Fiber Technol. 11, 209–228 (2005).
Cross, R. Edme mariotte and newton’s cradle. Phys. Teach. 50, 206–207 (2012).
Cross, R. Newton’s cradle in billiards and croquet. Phys. Educ. 51, 065020 (2016).
Gauld, C. & Cross, R. Understanding Newton’s cradle. I: modelling the ideal cradle. Phys. Educ. 56, 025001 (2021).
Haus, H. A. Theory of mode locking with a fast saturable absorber. J. Appl. Phys. 46, 3049–3058 (1975).
Haus, H. Theory of mode locking with a slow saturable absorber. IEEE J. Quantum Electron. 11, 736–746 (1975).
Kartner, F. X., Jung, I. D. & Keller, U. Soliton mode-locking with saturable absorbers. IEEE J. Sel. Top. Quantum Electron. 2, 540–556 (1996).
Anderson, M. et al. Observations of spatiotemporal instabilities of temporal cavity solitons. Optica 3, 1071–1074 (2016).
Chong, A., Renninger, W. H. & Wise, F. W. All-normal-dispersion femtosecond fiber laser with pulse energy above 20 nJ. Opt. Lett. 32, 2408–2410 (2007).
Tang, D. Y. et al. Soliton interaction in a fiber ring laser. Phys. Rev. E 72, 016616 (2005).
Liu, J. Q. et al. Photonic microwave generation in the X- and K-band using integrated soliton microcombs. Nat. Photon. 14, 486–491 (2020).
Zhang, K. Q. et al. Group delay and chromatic dispersion of thin-film-based, narrow bandpass filters used in dense wavelength-division-multiplexed systems. Appl. Opt. 41, 3172–3175 (2002).
Cui, X. Y. et al. Research on phase reconstruction and chromatic dispersion characteristic of thin film filters. Opt. Commun. 256, 123–131 (2005).
Gerken, M. & Miller, D. A. B. Multilayer thin-film coatings for optical communication systems. OSA Topical Meeting on Optical Interference Coatings 2004 (Optical Society of America, 2004).
Sargent, R. B. Optical Fiber Communication Conference 2004, TuD6. (Optical Society of America, 2004).
Hanzard, P. H. et al. 2021 Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference, FM4H-7 (IEEE, 2021).
Wabnitz, S. Control of soliton train transmission, storage, and clock recovery by cw light injection. J. Optical Soc. Am. B 13, 2739–2749 (1996).
Lu, Z. Z. et al. Synthesized soliton crystals. Nat. Commun. 12, 3179 (2021).
Cole, D. C. et al. Soliton crystals in Kerr resonators. Nat. Photon. 11, 671–676 (2017).
Niang, A. et al. Harmonic mode-locking in a fiber laser through continuous external optical injection. Opt. Commun. 312, 1–6 (2014).
Amrani, F. et al. Passively mode-locked erbium-doped double-clad fiber laser operating at the 322nd harmonic. Opt. Lett. 34, 2120–2122 (2009).
Amrani, F. et al. Passive harmonic mode locking of soliton crystals. Opt. Lett. 36, 4239–4241 (2011).
Herink, G. et al. Resolving the build-up of femtosecond mode-locking with single-shot spectroscopy at 90 MHz frame rate. Nat. Photon. 10, 321–326 (2016).
Lapre, C. et al. Real-time characterization of spectral instabilities in a mode-locked fibre laser exhibiting soliton-similariton dynamics. Sci. Rep. 9, 13950 (2019).
Zhou, H. et al. Soliton bursts and deterministic dissipative Kerr soliton generation in auxiliary-assisted microcavities. Light Sci. Appl. 8, 50 (2019).
Wei, X., Xie, Z. D. & Zhu, S. N. Self-injection locking of a distributed feedback laser diode using a high-finesse Fabry-Perot microcavity. Appl. Sci. 9, 4616 (2019).
Wang, Z. K. et al. Generation of pulse-width controllable dissipative solitons and bound solitons by using an all fiber saturable absorber. Opt. Lett. 44, 570–573 (2019).
Acknowledgements
We thank Prof. David J. Moss and Dr. Hualong Bao for helpful discussions. We thank Prof. Juliet Gopinath for lending the high-speed oscilloscope. M.N., B.L., Y.X., J.Y. and S.-W.H. acknowledge the support from the University of Colorado Boulder, National Science Foundation (OMA 2016244 and ECCS 2048202), and Office of Naval Research (N00014-22-1-2224). K.J., S.Z., and Z.X. acknowledge the support by the National Key R&D Program of China (2019YFA0705000, 2017YFA0303700), Key R&D Program of Guangdong Province (2018B030329001), Guangdong Major Project of Basic and Applied Basic Research (2020B0301030009), Zhangjiang Laboratory (ZJSP21A001), Leading-edge technology Program of Jiangsu Natural Science Foundation (BK20192001) and National Natural Science Foundation of China (51890861, 11690031, 11621091, 11627810, 11674169, 91950206).
Author information
Authors and Affiliations
Contributions
M.N. and S.-W.H. conceived the idea of the experiment. M.N. designed and performed the soliton generation and measurements with the help from Y.X. B.L., M.N. and J.Y. designed and performed the time magnifier measurement. M.N. performed theoretical modeling and numerical simulation. K.J., S.Z. and Z.X. fabricated the FFP microresonator. M.N., B.L. and S.-W.H. wrote the manuscript. S.-W.H. led and supervised the project. All authors contributed to the analysis of the data and discussion and revision of the manuscript.
Corresponding authors
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Supplementary information
41377_2022_998_MOESM1_ESM.docx
Supplementary Information for “Dissipative soliton generation and real-time dynamics in microresonator-filtered fiber lasers”
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Nie, M., Li, B., Jia, K. et al. Dissipative soliton generation and real-time dynamics in microresonator-filtered fiber lasers. Light Sci Appl 11, 296 (2022). https://doi.org/10.1038/s41377-022-00998-z
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41377-022-00998-z
- Springer Nature Limited