Abstract
While the water impermeable constraint has been conventionally adopted for analyzing the transport phenomena at the interface of electrolyte/nanoporous medium, non-negligible water-permeance through the medium results in significant effect on ion and particle transportation. In this work, a rigorous theoretical and experimental analysis of the water-permeance effect were conducted based on a fully-coupled analytical/numerical method and micro/nanofluidic experiments. The regime diagram with three distinctive types of concentration boundary layers (ion depletion, ion accumulation, and intermediate) near the ion exchange nanoporous medium was proposed depending on the medium’s permselectivity and the water-permeance represented by an absorbing parameter. Moreover, the critical absorbing parameters which divide the regimes were analytically obtained so that the bidirectional motion of particles were demonstrated only by altering the water-permeance without external stimuli. Conclusively, the presenting analysis of non-negligible water-permeance would be a substantial fundamental of transport phenomena at the interface of the ion exchange medium and electrolyte, especially useful for the tunable particle/ion manipulations in intermediate Peclet number environment.
Similar content being viewed by others
Introduction
Classically, a water-impermeable condition on the interface of a nanoporous medium and a bulk electrolyte has been generally chosen to analyze physicochemical transport phenomena because the internal volume of the nanoporous medium is usually smaller than the volume of outer electrolyte1,2,3. The condition is valid in the cases where the ionic flux induced by the water-permeance is negligible compared to the ionic flux due to the other external stimuli such as concentration difference4,5,6,7 and electric field8,9,10. For example, an ion concentration polarization phenomenon is triggered by electrically induced counter-ion flux across highly-charged nanoporous medium so that the theoretical model without considering the effect of water-permeance at the interface is enough to elucidate the transport phenomenon adequately11,12,13,14. However, in the case of reverse electrodialysis which is an energy harvesting platform utilizing a salt gradient across the nanoporous medium, diffusioosmotic water-permeance by diffusive flux could be a major transport mechanism15,16,17,18,19. In addition, it has been reported that a capillarity-driven water-permeance would naturally generate a permselective flux through the nanoporous medium, leading to the formation of ion depletion layer without external electrical power source20,21.
Similar to the capillarity-driven ion depletion layer, the salt gradient can be naturally formed by ion exchange process as well22. An internal proton would be exchanged with outer non-protonic cation through the Brownian motion of each ionic species. Classically, the total ion concentration outside the medium was treated as invariant because the exchange process was 1:123. However, recent researches have proven that the difference of diffusion rate between the proton and dissolved cation results in the natural ion depletion layer22 as shown in Fig. 1(a). The concentration gradient inside the natural ion depletion layer provides an effective particle transporting mechanisms, known as diffusiophoresis5,6,7,24, so that one can observe the exclusion zone (EZ) of colloidal suspension, which is a particle-free zone expanding up to O(1) mm, adjacent to the ion exchange surface25,26,27,28,29,30,31,32,33. Both analysis and direct visualization of EZ formation provide abundant information (e.g. surface charge density, porosity, Donnan equilibrium quantities, etc) concerning the nanoporous material as well as the nanoscale ion exchange process. Hence, the natural ion depletion phenomenon induced by the ion exchange has been drawn significant attentions recently22,25,26,27,28,29,30,31,33,34. Despite the fact that the proton inside the medium is being dissociated by the absorbed water from the outer solution as shown in Fig. 1(b), the correlation between the capillarity-governed water-permeance through nanoscale pore and the natural ion depletion phenomenon (or EZ formation) still remains unknown.
Considering the effect of the water-permeance, the convective flow toward the ion exchange medium would affect the natural ion depletion and the EZ formation. When the water-permeating velocity is too small to perturb the natural ion depletion layer, the total ion concentration (ctot) nearby the ion exchange interface decreases as reported in previous literatures22 where the water-permeance was neglected. The direction of diffusiophoretic force on a colloidal particle is toward the bulk so that the concentration gradient-induced force would be competing with convective drag force arisen from the water-permeance as shown in Fig. 1(c). On the other hand, the concentration profile would be inverted if the water-permeating velocity becomes considerable as shown in Fig. 1(d). In such case, the forces on the colloidal particle have the same direction so that the EZ would be collapsed. These two limiting situations imply that the water-permeance would play a critical role in the natural ion depletion phenomenon and the EZ formation. Thus, in this work, a rigorous theoretical analysis was conducted to more precisely figure out the natural ion depletion phenomenon inhibited by the capillarity-governed water-permeance. Moreover, the theoretical findings were experimentally verified by the direct visualization of EZ formation.
Theoretical Analysis
Numerical modeling of concentration boundary layer near the ion exchange medium
The numerical simulations were conducted on two theoretical domains; Domain 1 is the interior of the nanoporous ion exchange medium, and Domain 2 is the bulk solution near the medium. The permselectivity of the medium was represented by the Donnan concentration (N) and the water-permeability was represented by the absorbing parameter (S). In the Domain 1, the water-permeance was described by the Darcy’s law as
where Un is the water-permeating velocity into the medium, κ is the hydraulic permeability, μ is the viscosity of water, t is the time and Pc is the capillary pressure35. The Domain 2 was filled with electrolyte solution (e.g. KCl solution) with the bulk concentration of c0. In both domains, the transport of the three ionic species (K+, Cl−, and H+) was governed by the Poisson-Nernst-Planck equation as
and
Here, ci is the concentration of each ionic species i, x is the spatial coordinate, Di is the corresponding ion’s diffusivity, zi is the ionic valence, F is the Faraday constant, R is the gas constant, T is the absolute temperature, ψ is the electric potential, Uj is the flow velocity in Domain j, ε is the electrical permittivity of water, ρe is the volumetric charge density. The flow velocity in Domain 2 (Um) was determined by
where φp was the porosity of the ion exchange medium. See Supplementary Note 1 for detailed physics.
Simplification of the fully coupled model
When N/c0 \(\gg \) 1, an ideal permselectivity condition (i.e. jCl = 0) enables the simplification of the fully-coupled model with the analytically obtained ctot as
where Di,eff is the effective diffusivity (Di,eff = 2DiDCl /(Di + DCl)), and cH,S is a constant defined as
The analytical solutions (symbols) and the numerical solutions (lines) of fully coupled model show a good agreement as shown in Fig. 2(a–c). See Supplementary Note 2 for detailed derivations.
Results and Discussion
Characterization of the concentration boundary layer with water-permeance
According to the results in Fig. 2(a–c), the characteristics of ctot profile near the ion exchange medium is highly dependent on the water-permeability of the medium. The Fig. 2(a) shows the ion depletion when S is small as in the conventional water-impermeable condition. The thick red line (ctot) near the medium becomes smaller than c0 near the medium. Under this concentration gradient, the direction of diffusiophoresis is toward the bulk. On the contrary, when S is high as shown in Fig. 2(b), the ctot near the medium is higher than c0 and monotonically decreases toward the bulk. With such a high water-permeance, ion exchange at the interface is suppressed because the diffusion of protons toward the bulk is hindered by the convective flow, leading to the ion accumulation near the interface. At this time, the direction of diffusiophoresis is toward the ion exchange interface. Figure 2(c) shows the intermediate situation where ctot has a local maximum, while ctot is higher than c0 near the medium. The position of the local maximum moves toward the bulk as a function of time. Therefore, charged particles near the medium moves to the bulk following the moving maximum so that the charged particles cannot be used as tracers to determine whether the total concentration near the medium is decreased or not, i.e. the particle behaves like the ion depletion, while actual ions are accumulated near the medium.
These concentration profiles affected by the water-permeance were verified by direct visualization of EZ formation in pseudo 1-dimensional micro/nanofluidic chips shown in Fig. 3(a). The microfluidic chip had a reservoir at an end of the microchannel, and the other end was connected with a straight nanoporous medium as described in Fig. 3(b). As a building block of the microchannel, polydimethyl-siloxane (PDMS, Sylgard 184 silicone elastomer kit, Dow Corning, USA) was used. The ion exchange medium was either of Nafion (Sigma Aldrich, USA) or dry hydrogel which represented as materials having low or high water-permeability, respectively. See Supplementary Note 3 for detailed device fabrication and experimental setup.
Nafion which represented as the ion exchange medium of low water-permeability showed the developing EZ with the charged particles excluded to the bulk reservoir as shown in Fig. 3(c). On the other hand, dry hydrogel which simulated as the medium of high water-permeability showed the collapse of the EZ with an accumulation of charged particles as in Fig. 3(d). The fluorescent signal near the medium (left side of the microchannel) became brighter since the fluorescent particles were accumulated near the hydrogel medium. See Supplementary Video 1.
The regime diagram
Based on this analysis, a regime diagram which also incorporates the correlation between the permselectivity (N) and the water-permeability (S) is proposed in Fig. 4. The regime diagram contains the three types of ctot profiles (ion depletion, ion accumulation, and intermediate) with respect to N and S. The ion depletion occurs under high N and low S conditions while the ion accumulation occurs under the low N and high S conditions. According to the regime diagram, it is confirmed that the Nafion belongs to the ion depletion regime with the estimated S of 2.1 × 10−11 m2/s, and N of 7.2 × 102 mM, and the dry hydrogel belongs to the ion accumulation regime with the estimated S of 3.5 × 10−9 m2/s and N of 1.8 mM. The S values were measured by tracking the particles near the reservoir where the diffusiophoretic force can be neglected, and the N values were estimated by measuring the conductance of a microchannel coated with the nanoporous medium. See Supplementary Notes 4 and 5 for detailed information.
The critical lines in the regime diagram are obtained using the ctot and ∂ctot/∂x values at the interface (x = 0). The first critical line in Fig. 4 decides whether ctot at the surface of ion exchange medium (x = 0) is higher than c0 or not, and the second critical line determines whether the local maximum of the concentration is formed or not. A notable observation on the critical lines is that the lines vertically divide the regimes when N > 10 mM (i.e. N/c0 \(\gg \) 1). This indicates the regime is solely determined by the critical S values (Sdep and Sacc) when N was high enough to assure the ideal permselectivity, and thus, the critical S values could be also obtained analytically as well as numerically. The analytically obtained values of Sdep and Sacc were 3.16 × 10−11 m2/s and 1.26 × 10−10 m2/s, respectively and the numerically obtained ones were 6.28 × 10−11 m2/s and 2.53 × 10−10 m2/s, respectively. The numerically obtained values were slightly greater than ones by analytical solution due to the ideal permselectivity assumption. However, they still convey a significant physical intuition since one can guarantee the direction of diffusiophoresis to the bulk if S was selected below 3.16 × 10−11 m2/s (analytically obtained Sdep).
Bidirectional particle motion
While aforementioned regime diagram based on 1-dimensional analysis brought the significant physical interpretation of a nanoporous medium, a practical 2- or 3-dimensional micro/nanofluidic configuration can alter water-permeance depending on the ratio of cross-sectional area of the medium to the microchannel. Once the medium was chosen (i.e. an S value was set), one can setup the two forces acting on a charged particle as in Fig. 1(c) or (d). The particle’s moving velocity (Up) is represented by the sum of two velocities as
Here Um is the flow velocity from Eqs (1 and 4) and UDP is the diffusiophoretic velocity22 where DDP is the diffusiophoresis constant depending on the zeta potential of a particle, viscosity of fluid, temperature, and diffusivity of ions36. Note that both of the velocities in Eq. (7) are inversely proportional to the square root of t, which indicates the direction of the particle’s motion should be unidirectional. Thus, if the particle moves to the bulk in the beginning, it keeps flowing to the bulk and vice versa. This was verified from the pseudo 1-dimensional experimental demonstration in Fig. 3(c) or (d). For example, the particle exclusion in Fig. 3(c) lasted for more than 16 hours until the ion exchange process ended after reaching the equilibrium. This was the limitation of pseudo 1-dimensional configuration where the direction of particle motion was uncontrollable. In this work, this unidirectional motion became a bidirectional motion through the higher-dimensional configuration to adjust the water permeable boundary condition. If the ion exchange medium was patterned as funnel shape as shown in the inset of Fig. 5(a), the flow velocity induced by the imbibition is expected to deviate from the t−1/2 dependency37,38,39,40. Figure 5(a) showed the simulated water-permeance based on the Richard’s equation40, and more information on the simulations is available in Supplementary Note 6. Until t1, water was absorbed through the straight pathway following the conventional Darcy’s law. After t1, a sudden increase of water influx induced by the diverging pathway led to the saturated imbibition velocity until t239. Finally, the imbibition head reached the end of the medium at t2 and the water absorption dropped dramatically after t2. Finally, the medium was fully wetted at t3. Note that, as described in equation (7), the velocity of particle is the summation of imbibition velocity through microchannel and diffusiophoretic velocity. Also shown in equation (7), diffusiophoretic velocity is independent from geometrical dimension. However, change in geometric/channel dimensions affects the imbibition velocity (or the length of exclusion zone). It depends on the ratio of cross-section, An/Am, as below.
where Am: cross-sectional area of microchannel, An: cross-sectional area of nanoporous medium, φp: porosity of nanoporous medium and Un: velocity of the imbibition head in nanoporous medium. This is obtained from the flow continuity condition, and the bidirectional motion of charged particles was demonstrated by utilizing this relation. In that experiment, An was manipulated. Likewise, the dimension of a microchannel also has similar effects on the exclusion zone.
Based on this analysis, one can expect the direction shifts of charged particles’ motion and the experimental demonstration was provided in Fig. 5(b). See Supplementary Video 2. Figure 5(c) showed the exclusion distance (δ) of the charged particles extracted from Fig. 5(b). Until t1’, the system was in pseudo one-dimensional configuration with the water absorbed the straight pathway. The diffusiophoretic velocity was faster than the flow velocity in this region so that δ increased as a function of t1/2 until t1’. Between t1’ and t2’, flow velocity exceeded the diffusiophoretic velocity due to the expanding imbibition pathway. During the period, the particles moved backward to the ion exchange medium, and δ decreased proportional to time t due to the saturated flow velocity. Then the imbibition head reached the end of the funnel shaped medium and the flow velocity suddenly dropped at t2’. Finally, the medium was fully wetted and the particles were excluded again toward the bulk having δ proportional to (t + t3’)1/2 after t3’. This second exclusion lasted for more than 7 hours until the ion exchange reached the equilibrium. During the entire process, the motion of particles was governed by the shape of medium, while only one type of material was used (i.e. fixed S).
Conclusions
As demonstrated, the nanoporous medium which can imbibe water using capillary force induces the convective flow toward the medium, and the permeable flow should affect the formation of the concentration boundary layer. The presenting analysis would provide (1) the regime diagram with three distinctive types of concentration profiles (ion depletion, ion accumulation, and intermediate) depending on the permselectivity and the water-permeance, (2) the critical S values (Sdep, Sacc) which divide the regimes, and (3) the practical utilities of the critical S values for bidirectional control of particle motion without external stimuli. Therefore, the new insight of critical role of water-permeance would be a seminal physics for interpreting transport phenomena at the interface of the ion exchange medium and electrolyte, especially useful for the tunable particle/ion manipulations in intermediate Peclet number environment.
References
Probstein, R. F. Physicochemical Hydrodynamics: An Introduction. (Wiley-Interscience, 1994).
Levich, V. G. Physico-Chemical Hydrodynamics. (Prentice-Hall, 1962).
Reto, B. S., Jongyoon, H. & Philippe, R. Transport phenomena in nanofluidics. Rev. Mod. Phys. 80, 839 (2008).
Ault, J. T., Warren, P. B., Shin, S. & Stone, H. A. Diffusiophoresis in one-dimensional solute gradients. Soft matter 13, 9015–9023 (2017).
Boulogne, F., Shin, S., Dervaux, J., Limat, L. & Stone, H. A. Diffusiophoretic manipulation of particles in a drop deposited on a hydrogel. Soft matter 13, 5122–5129 (2017).
Shin, S., Ault, J. T., Feng, J., Warren, P. B. & Stone, H. A. Low-Cost Zeta Potentiometry Using Solute Gradients. Adv Mater 29, https://doi.org/10.1002/adma.201701516 (2017).
Shin, S. et al. Size-dependent control of colloid transport via solute gradients in dead-end channels. Proc. Natl. Acad. Sci.USA 113, 257–261, https://doi.org/10.1073/pnas.1511484112 (2016).
Nikonenko, V. V. et al. Desalination at overlimiting currents: State-of-the-art and perspectives. Desalination 342, 85–106, https://doi.org/10.1016/j.desal.2014.01.008 (2014).
Kwak, R., Pham, V. S., Lim, K. M. & Han, J. Y. Shear Flow of an Electrically Charged Fluid by Ion Concentration Polarization: Scaling Laws for Electroconvective Vortices. Phys. Rev. Lett. 110, 114501, https://doi.org/10.1103/PhysRevLett.110.114501 (2013).
Deng, D. et al. Overlimiting Current and Shock Electrodialysis in Porous Media. Langmuir 29, 16167–16177 (2013).
Kim, J., Cho, I., Lee, H. & Kim, S. J. Ion Concentration Polarization by Bifurcated Current Path. Sci Rep 7, 5091, https://doi.org/10.1038/s41598-017-04646-0 (2017).
Kim, J., Kim, H.-Y., Lee, H. & Kim, S. J. Pseudo 1-D Micro/Nanofluidic Device for Exact Electrokinetic Responses. Langmuir 32, 6478–6485, https://doi.org/10.1021/acs.langmuir.6b01178 (2016).
Cho, I. et al. Non-Negligible Diffusio-Osmosis Inside an Ion Concentration Polarization Layer. Phys. Rev. Lett. 116, 254501 (2016).
Green, Y. & Yossifon, G. Dynamical trapping of colloids at the stagnation points of electro-osmotic vortices of the second kind. Phys. Rev. E 87, https://doi.org/10.1103/PhysRevE.87.033005 (2013).
Cao, L. X. et al. Towards understanding the nanofluidic reverse electrodialysis system: well matched charge selectivity and ionic composition. Energy & Environmental Science 4, 2259–2266, https://doi.org/10.1039/c1ee01088c (2011).
Cao, L. et al. Anomalous Channel‐Length Dependence in Nanofluidic Osmotic Energy Conversion. Advanced Functional Materials 27 (2017).
van der Heyden, F. H. J., Bonthuis, D. J., Stein, D., Meyer, C. & Dekker, C. Electrokinetic energy conversion efficiency in nanofluidic channels. Nano Lett. 6, 2232–2237, https://doi.org/10.1021/nl061524l (2006).
Logan, B. E. & Elimelech, M. Membrane-based processes for sustainable power generation using water. Nature 488, 313–319 (2012).
Ramon, G. Z., Feinberg, B. J. & Hoek, E. M. Membrane-based production of salinity-gradient power. Energy & environmental science 4, 4423–4434 (2011).
Park, S. et al. Capillarity ion concentration polarization as spontaneous desalting mechanism. Nat Commun 7, https://doi.org/10.1038/ncomms11223 (2016).
Oh, Y., Lee, H., Son, S. Y., Kim, S. J. & Kim, P. Capillarity ion concentration polarization for spontaneous biomolecular preconcentration mechanism. Biomicrofluidics 10, 014102, https://doi.org/10.1063/1.4939434 (2016).
Florea, D., Musa, S., Huyghe, J. M. R. & Wyss, H. M. Long-range repulsion of colloids driven by ion exchange and diffusiophoresis. P Natl Acad Sci USA 111, 6554–6559, https://doi.org/10.1073/pnas.1322857111 (2014).
Helfferich, F. G. Ion exchange. (McGraw-Hill, 1962).
Shin, S., Ault, J. T., Warren, P. B. & Stone, H. A. Accumulation of Colloidal Particles in Flow Junctions Induced by Fluid Flow and Diffusiophoresis. Phys Rev X 7, https://doi.org/10.1103/PhysRevX.7.041038 (2017).
Chai, B., Mahtani, A. G. & Pollack, G. H. Unexpected Presence of Solute-Free Zones at Metal-Water Interfaces. Contemp Mater 3, 1–12, https://doi.org/10.7251/COM1201001C (2012).
Chai, B. H., Yoo, H. & Pollack, G. H. Effect of Radiant Energy on Near-Surface Water. J Phys Chem B 113, 13953–13958, https://doi.org/10.1021/jp908163w (2009).
Klyuzhin, I., Symonds, A., Magula, J. & Pollack, G. H. New method of water purification based on the particle-exclusion phenomenon. Environ Sci Technol 42, 6160–6166, https://doi.org/10.1021/es703159q (2008).
O’Rourke, C., Klyuzhin, I., Park, J. S. & Pollack, G. H. Unexpected water flow through Nafion-tube punctures. Phys Rev E 83, https://doi.org/10.1103/PhysRevE.83.056305 (2011).
Lee, H., Kim, J., Yang, J., Seo, S. W. & Kim, S. J. Diffusiophoretic exclusion of colloidal particles for continuous water purification. Lab Chip 18, 1713-1724, https://doi.org/10.1039/c8lc00132d (2018).
Schurr, J. M., Fujimoto, B. S., Huynh, L. & Chiu, D. T. A Theory of Macromolecular Chemotaxis. J Phys Chem B 117, 7626–7652, https://doi.org/10.1021/jp302587d (2013).
Sulbaran, B., Toriz, G., Allan, G. G., Pollack, G. H. & Delgado, E. The dynamic development of exclusion zones on cellulosic surfaces. Cellulose 21, 1143–1148, https://doi.org/10.1007/s10570-014-0165-y (2014).
Zheng, J. M. & Pollack, G. H. Long-range forces extending from polymer-gel surfaces. Phys Rev E 68, https://doi.org/10.1103/PhysRevE.68.031408 (2003).
Zheng, J. M., Wexler, A. & Pollack, G. H. Effect of buffers on aqueous solute-exclusion zones around ion-exchange resins. J Colloid Interf Sci 332, 511–514, https://doi.org/10.1016/j.jcis.2009.01.010 (2009).
Huszar, I. N., Martonfalvi, Z., Laki, A. J., Ivan, K. & Kellermayer, M. Exclusion-Zone Dynamics Explored with Microfluidics and Optical Tweezers. Entropy-Switz 16, 4322–4337, https://doi.org/10.3390/e16084322 (2014).
Gruener, S., Hofmann, T., Wallacher, D., Kityk, A. V. & Huber, P. Capillary rise of water in hydrophilic nanopores. Phys Rev E 79, 067301, https://doi.org/10.1103/PhysRevE.79.067301 (2009).
Keh, H. J. Diffusiophoresis of charged particles and diffusioosmosis of electrolyte solutions. Curr Opin Colloid In 24, 13–22, https://doi.org/10.1016/j.cocis.2016.05.008 (2016).
Benner, E. M. & Petsev, D. N. Potential flow in the presence of a sudden expansion: Application to capillary driven transport in porous media. Phys Rev E 87, https://doi.org/10.1103/PhysRevE.87.033008 (2013).
Elizalde, E., Urteaga, R. & Berli, C. L. A. Rational design of capillary-driven flows for paper-based microfluidics. Lab Chip 15, 2173–2180, https://doi.org/10.1039/c4lc01487a (2015).
Mendez, S. et al. Imbibition in Porous Membranes of Complex Shape: Quasi-stationary Flow in Thin Rectangular Segments. Langmuir 26, 1380–1385, https://doi.org/10.1021/la902470b (2010).
Perez-Cruz, A., Stiharu, I. & Dominguez-Gonzalez, A. Two-dimensional model of imbibition into paper-based networks using Richards’ equation. Microfluidics and Nanofluidics 21, https://doi.org/10.1007/s10404-017-1937-0 (2017).
Acknowledgements
This work is supported by Basic Research Laboratory Project (NRF-2018R1A4A1022513), Basic Science Research Program (2016R1A1A1A05005032 and 2016R1A6A3A11930759) and the Center for Integrated Smart Sensor funded as Global Frontier Project (CISS- 2011-0031870) by the Ministry of Science, ICT & Future Planning and Korean Health Technology RND project, Ministry of Health and Welfare Republic of Korea (HI13C1468, HI14C0559). Also this work is partially supported by Samsung Research Funding Center of Samsung Electronics under (SRFC-MA1301-02) and BK21 plus program. S. J. Kim acknowledged a financial support from LG Yonam Foundation.
Author information
Authors and Affiliations
Contributions
J.A. Lee mainly analyzed the diffusiophoretic migration and D. Lee conducted main experiments. S. Park fabricated the micro/nanofluidic device. H. Lee and S.J. Kim supervised the project. All authors wrote the manuscript.
Corresponding authors
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Lee, J.A., Lee, D., Park, S. et al. Non-negligible Water-permeance through Nanoporous Ion Exchange Medium. Sci Rep 8, 12842 (2018). https://doi.org/10.1038/s41598-018-29695-x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-29695-x
- Springer Nature Limited
This article is cited by
-
Effect of evaporation through nanoporous medium on diffusiophoresis
Micro and Nano Systems Letters (2020)
-
Spontaneous diffusiophoretic separation in paper-based microfluidic device
Micro and Nano Systems Letters (2020)
-
Nanoelectrokinetic Selective Preconcentration Based on Ion Concentration Polarization
BioChip Journal (2020)
-
Spontaneous Selective Preconcentration Leveraged by Ion Exchange and Imbibition through Nanoporous Medium
Scientific Reports (2019)