Abstract
Conventional suture anchors (CAs) and all-suture anchors (ASAs) are used for rotator cuff repair. Pull-out strength (POS) is an important factor that affects surgical outcomes. While the fixation mechanism differs between the anchor types and relies on the quality, few studies have compared biomechanical properties of anchors based on bone quality. This study aimed to compare the biomechanical properties of anchors using osteoporotic bone (OB) and non-osteoporotic bone (NOB) simulators. Humerus simulators were fabricated using fused deposition modeling of 3D printing and acrylonitrile butadiene styrene adjusting the thickness of cortical bone and density of cancellous bone based on CT images. Cyclic loading from 10 to 50 N, 10 to 100 N, and 10 to 150 N for 10 cycles was clinically determined at each anchor because the supraspinatus generates a force of 67–125 N in daily activities of normal control. After cyclic loading, the anchor was extruded at a load of 5 mm/min. Displacement, POS, and stiffness were measured. In OB simulators, CAs revealed bigger gap displacement than ASAs with cyclic loading of 10–150 N. ASA showed higher values for POS and stiffness. In NOB simulators, ASAs revealed bigger gap displacement than CAs with cyclic loading of 10–150 N. ASA showed higher values for POS and CA showed higher values for stiffness. POS of anchors depends on anchors ‘displacement and bone stiffness. In conclusion, ASA demonstrated better biomechanical performance than CA in terms of stability under cyclic loading and stiffness with similar POS in OB.
Similar content being viewed by others
Introduction
Rotator cuff repair surgery is a transosseous equivalent repair that is performed using a suture anchor similar to that in conventional transosseous repair1. Currently, screw-in type of conventional suture anchors (CAs) and all-suture anchors (ASAs) have become popular in rotator cuff repair surgery1,2,3. Most repairs performed using CAs provide sufficient fixation force until tendon-to-bone healing is achieved; however, this depends on the bone quality4. In contrast, ASAs depend on the quality of the cortical bone rather than that of the cancellous bone5. The pull-out strength (POS) of a suture anchor is one of the determining factors of early failure. Therefore, the POS of ASAs and CAs has been evaluated in various bone quality environments1,2,3,4,5. Furthermore, biomechanical tests have been conducted using human cadaveric specimens6,7,8. To thoroughly understand the characteristics of the anchor, specimens that reflect the mechanical properties of osteoporotic bone (OB) and non-osteoporotic bone (NOB) should be used5. However, cadaveric bone is difficult to obtain and has ethical issues. Furthermore, the shape, bone quality, and strength of bones vary between cadavers. Consequently, the standard deviation could become exceptionally large under similar experimental conditions9. Due to these difficulties, recent studies have performed biomechanical tests using synthetic plastic bone7,10. Synthetic bones have uniform mechanical properties and can be obtained easily, although they do not precisely reflect the mechanical properties of OBs and NOBs11,12,13. We propose the development of patient-specific and realistic humerus simulators for anchor insertion using three-dimensional (3D) printing and deriving the mechanical properties using computed tomography (CT). The purpose of this study was to evaluate and compare the biomechanical properties of CAs and ASAs in 3D-printed OB and NOB simulators. We aimed to verify the hypothesis that ASAs are stronger than CAs in OBs.
Methods
For fabrication and evaluation of the humerus bone simulator, the bone was segmented and designed for biomechanical testing based on the CT images. Then, the simulators were fabricated using a 3D printer with the appropriate mechanical properties. Biomechanical testing was performed by extruding the anchors inserted into these fabricated simulators.
Preparation of the humerus simulator
This study was approved by the Institutional Review Board of Asan Medical Center (IRB No. 2021-2046) and was performed according to the principles of the Declaration of Helsinki. The requirement for informed consent was waived by the Institutional Review Board due to the retrospective observational design. Anonymized multiple detector CT images by removing personal information were obtained using a 120-Kvp tube voltage and 1-mm slice thickness in a 71-year-old male who was scheduled for shoulder joint replacement surgery. The humerus was segmented using the thresholding function of 123–1546 Hounsfield units as well as the region growing functions from manually chosen seeds by an expert (Fig. 1A). The segmented humerus was converted to stereolithography format. As all areas of the humerus are not required to measure the POS, only an area of 100 mm from the top was used as the region of interest (Fig. 1A). In patients in their 60 s, the density of the greater tuberosity (GT) in the shoulder with rotator cuff tears is 200 mg/cm3, while that on the healthy side is 300 mg/cm314. Furthermore, the cortical thickness of the proximal humerus is approximately 2 mm15. Therefore, The OB simulator was designed with an outer layer of 1.5 mm by reducing the thickness by 0.5 mm, the internal structure was designed with a gyroid shape infill to 15% to create a density of 200 mg/cm3. The NOB simulator was designed with an outer layer of 2.5 mm by increasing the thickness by 0.5 mm, the internal structure was designed with a gyroid shape infill to 22% to create a density of 300 mg/cm3. Two patterns are visualzied in Fig. 1C,D. The mean compressive strength for the human humerus is 107 MPa and a 3D-printed acrylonitrile butadiene styrene (ABS) specimens can have a compressive strength of approximately 100 MPa following surface treatment16,17. Therefore, the simulators were fabricated using fused deposition modeling (FDM) with ABS filament (Ultimaker S5, Ultimaker, The Netherlands), and the surface was polished using fumigation in a vapor treatment machine (Bboshasi 250k, Kobot, South Korea) for 7 min. Finally, 20 artificial proximal humerus simulators (10 OB and 10 NOB stimulators) were fabricated (Fig. 2A,B).
Preparation of the suture anchors and implantation
Commercially available Q-Fix (outer diameter 2.8 mm, length 20 mm) ASAs (Smith & Nephew, Andover, MA, USA) and Healicoil (outer diameter 5.5 mm, length 18 mm) CAs (Smith & Nephew) were used. Q-fix expands to approximately 5.5 mm after deployment, and the maximum outer diameter of Healicoil was 5.5 mm. As their scalability is similar, we used both anchors to evaluate if there was any difference between the anchor types due to bone quality. The orthopedic surgeon inserted both anchors according to the manufacturer's instructions. A pilot hole tapping guide was placed on the GT of each humerus simulator and the pilot hole size of ASAs and CAs a diameter of 1 mm and 3 mm pilot hole was made using an awl. Each anchor was inserted anchors vertically into the GT of the humerus simulator through the guide, it was firmly fixed using a mallet. Subsequently, guide, handle, and suture strands were removed, sequentially. Suture strands and the body of the humerus were fixed on a universal testing machine (ST-1001, SALT Corp., Korea). A total of 20 biomechanical tests were determined through the Design of Experiments (DoE) via Taguchi methods was designated using 2 parameters, 2 levels, and 5 repeats (Table 1). The number of repetitions of each condition was determined through the TTestIndPower package in Pythons (effect size = 0.8, alpha error = 0.05, power = 0.2). Five experiments were conducted for each condition (5 CA with OB, 5 CA with NOB, 5 ASA with OB, and 5 ASA with NOB), and a total of 20 biomechanical tests were conducted18.
Biomechanical testing
POS, stiffness, and gap displacement under cyclic loading were measured using a universal testing machine with a 500-N load cell and at room temperature (Fig. 2C). We applied a preload of 10 N in 1 min to the anchor via the sutures prior to cyclic loading over the inserted anchor. The supraspinatus generates a force of 67–125 N in daily activities19. Patients may engage in activities cautiously but may inevitably make large movements. Cyclic loading from 10 to 50 N, 10 to 100 N, and 10 to 150 N for 10 cycles each at a rate of 0.5 Hz was clinically determined by an expert orthopedic surgeon with more than 20 years of experience based on daily supraspinatus generates a force. The gap displacement of the extruded anchor was measured using vernier calipers with repeat accuracy of 0.01 mm (CD-30AX, Mitutoyo Co., Japan) at the end of each cycle. Subsequently, we measured the POS and stiffness by extruding the anchor at a speed of 5 mm/min according to American Society for Testing and Materials F1839-08. The test of the above conditions was continually conducted on one simulator in reuse manner.
Statistical analysis
The difference in the POS and stiffness between ASAs and CAs in OBs and NOBs were analyzed using the Mann–Whitney U test. The pattern between the ASA and CA in terms of the gap displacement with accumulated cyclic loading was compared using the Friedman test. Finally, the groups were compared individually using the Mann–Whitney U test. The significance level was set to p < 0.05, and the analyses were performed using Excel (Microsoft Inc., Redmond, WA, USA) and SPSS v25 (IBM Corp., Armonk, NY, USA).
Results
Biomechanical testing
In OBs with ASAs, the gap displacement (mean ± standard deviation [SD]) with cyclic loading of 10–50, 10–100, and 10–150 N was 1.6 ± 0.5, 3.1 ± 0.41, and 4.6 ± 1.5 mm, respectively (Fig. 3A). In OBs with CAs, the gap displacement was 0.8 ± 0.4, 2.8 ± 0.8, and 11.7 ± 3.4 mm, respectively (Fig. 3A). In OBs, the gap displacement with the accumulation of cyclic loading was significantly different between ASAs and CAs (p < 0.001). In OBs with CAs, the gap displacement was significantly different between cyclic loading of 10–50 N (p = 0.037) and 10–150 N (p = 0.009). In NOBs with ASAs, the gap displacement with cyclic loading of 10–50, 10–100, and 10–150 N was 0.6 ± 0.9, 1.6 ± 1.4, and 4.8 ± 1.1 mm, respectively (Fig. 3B). In NOBs with CAs, the gap displacement was 0.4 ± 0.9, 1.4 ± 0.5, and 2.1 ± 0.7 mm, respectively (Fig. 3B). In NOBs, the gap displacement with the accumulation of cyclic loads was significantly different between ASAs and CAs (p = 0.001). Specifically, a significant gap displacement with ASA was identified with 10–150 N of cyclic loading (p = 0.011) in NOBs. The POSs (mean ± SD) of ASAs (193.5 ± 11.2 N) and CAs (177.6 ± 38.1 N) were not significantly different in OBs (p = 0.841). The POSs of ASAs and CAs were significantly different in NOBs (433.5 ± 48.8 and 347.2 ± 16.0 N, respectively; p = 0.015), although both POSs were > 300 N, which is strong enough to be used in rotator cuff repair (Fig. 4A). The stiffness (mean ± SD) of OB with ASAs and CAs was 45.5 ± 13.3 and 16.2 ± 5.8 N/mm, respectively, with a significant difference between them (p = 0.007). The stiffness of NOB with ASAs and CAs was 95.8 ± 30.6 and 196.8 ± 96.5 N/mm, respectively, with a significant difference (p = 0.031) (Fig. 4B).
Discussion
The most interesting finding of this study was that CAs in OBs revealed a relatively larger gap displacement after cyclic loading of 10–150 N than ASAs, while ASAs revealed a greater gap displacement than CAs in NOBs. It might imply that CA is weaker in OBs with higher cyclic loading, while ASA is weaker in NOBs. In OB, CA shows lower gap displacement than ASA at cyclic loads below 10–100 N, however, the trend reversed at 10–150 N. Therefore, it would be preferable to use CA in patients with low activity and ASA in patients with high activity. In NOB, ASA and CA show similar gap displacement at cyclic loads below 10–100 N, however, ASA higher gap displacement than CA at 10–150 N. Therefore, it would be preferable to use CA in patients with high activity. Optimal healing occurred when the gap between the surgical site and the anchor was less than 5 mm20. In NOB, both anchors can expect optimal treatment effects. In OB with CA, it seems difficult to expect optimal treatment effects in patients of high activity. Additionally, while the POS was similar between the anchors in OBs, the stiffness was greater with ASAs than that with CAs, which implied that the strength of the bone to withstand POS was stronger with ASAs in OBs than that with CAs. These findings highlight the overall better biomechanical performance and optimal healing of ASAs over CAs, especially in OBs. Treating patients with osteoporosis and rotator cuff repair using CAs may result in a risk of failure21. Therefore, rotator cuff repair using ASAs should be considered for older patients, females, or patients with risk factors for osteoporosis; however, the cortical bone should be preserved. Our results assume an intact cortical bone, although we simulated osteoporosis both in trabecular and cortical bone. Conventionally, the cortical bone is removed to promote healing from the bleeding bone bed in rotator cuff repair. If we damage the cortical bone for bone bed preparation, the fixation strength of ASA is decreased significantly. Some researchers have highlighted the importance of cortical bone preservation to hold ASAs22. Therefore, whether the cortex should be preserved for ASAs or should be removed for better healing along with the use of CAs, especially in OBs, warrants further investigations.
In our study, NOBs revealed sufficient POS (433.5 ± 48.8 N for ASA; 347.2 ± 16.0 N for CA) and stiffness (95.8 ± 30.6 N/mm for ASA; 190.8 ± 96.5 N/mm for CA). NOBs revealed < 5 mm gap displacement for cyclic loading with both anchors as well. Although there were statistically significant differences in all parameters, even the weak ASAs revealed enough biomechanical properties to be used in rotator cuff repair of NOBs. Both ASAs and CAs appear to work well in NOBs; however, ASAs are inserted through a 2.8-mm pilot hole, which can minimize bone loss. Therefore, ASAs may be advantageous over CAs in NOBs5.
Despite previous studies using synthetic simulators, the understanding of variations in the thickness of the cortical bone (osteoporosis) and its effects on POS remains limited7,23. In our study, POS was not significantly different between ASAs and CAs in OBs, as both anchors are primarily influenced by cortex thickness or stiffness. The weak POS following CA in OBs was expected due to trabecular bone quality dependence4. While the POS of ASA was similar, the stiffness was greater than that of CA in OBs. Collectively, ASA could be a better alternative than CA in OBs.
We designed OBs and NOBs based on the density of trabecular bone and the thickness of the cortical layer14,15. The simulators were fabricated using ABS, whose compressive strength is similar to that of the humerus16,17. According to Barber et al., the POS of the synthetic plastic bone and that of porcine bone using Q-Fix 2.8 mm is 494.7 ± 1.1 and 495.1 ± 87.9 N, respectively24. In our study, the POS of ASAs in NOBs was 433.5 ± 48.8 N, which was similar to that in the previous study. The POS of CAs in OBs was 177.6 ± 38.1 N, which was similar to the findings of Yamauchi et al. who used Healicoil (5.5 mm) and reported that the POS of synthetic plastic bone with osteoporosis was 146.3 ± 5.8 N25. Therefore, our simulator model demonstrated a similar POS as previous studies using polyurethane foam and animal models. The stiffness of both ASA and CA in human humeri aged between 50 and 73 years old is around 70 N/mm26. In our study stiffness of the ASA and CA is in NOB 95.8 ± 30.6 and 196.8 ± 96.5 N/mm, which shows a difference from the previous study. It seems that our homogeneous gyroid inner pattern does not mimic diversity in real bone, resulting in relatively high stiffness.
Previously reported synthetic plastic bone models did not consider the cortical bone layer, hardness of the trabecular layer, and its external shape27. Cadaver bones vary in shape, mechanical properties, and bone quality or strength28. Furthermore, cadavers are not easily available, and it is extremely difficult to obtain osteoporotic cadavers. Therefore, it is difficult to measure the biomechanical properties of implants, such as suture anchors, especially in OBs9. Our bone simulators closely replicated actual bone shape and mechanical properties through 3D printing and CT images. This approach offers a valuable means of assessing the mechanical properties of medical devices that are applied to the bones. Moreover, it has the potential for the pre-evaluation of anchor fixation stability in various positions by using patient-specific simulators based on CT images of patients with bone deformities and conducting procedural simulations.
This study has some limitations. First, we considered the actual density and structure of the trabecular layer of OBs and NOBs but did not mimic the trabecular microstructure realistically. Second, the cortical bone of the simulator was mimicked only by controlling the cortical bone layer in OBs. In an OB, the density or porosity of the cortical bone is altered along with the thickness. The density or porosity of the cortical layer was not controlled in our study. Real cortical bone has some irregular microstructures (porosity)29. In future studies, we will fabricate a humerus simulator using two or more materials considering bone's anisotropic and heterogeneous and evaluate the mechanical properties of the anchor. Lastly, the 3D-printed simulator used in this study was not compared with osteoporotic and non-osteoporotic cadaver bones.
Conclusion
In simulated OBs, ASAs demonstrated better biomechanical performance than CAs in terms of stability under cyclic loading and stiffness with similar POSs.
Data availability
The datasets generated in this study during the current study are not publicly available because the data used in our study were created based on patient images but are available from the corresponding author on a reasonable request.
References
Longo, U. G. et al. Metallic versus biodegradable suture anchors for rotator cuff repair: A case control study. BMC Musculoskelet. Disord. 20(1), 477 (2019).
Barber, F. A. & Herbert, M. A. Cyclic loading biomechanical analysis of the pullout strengths of rotator cuff and glenoid anchors: 2013 update. Arthroscopy 29(5), 832–844 (2013).
Alan Barber, F. et al. Biomechanical analysis of pullout strengths of rotator cuff and glenoid anchors: 2011 update. Arthrosc. J. Arthrosc. Relat. Surg. 27(7), 895–905 (2011).
Meyer, D. C. et al. The use of acrylic bone cement for suture anchoring. Clin. Orthop. Relat. Res. 410, 295–302 (2003).
Ntalos, D. et al. All-suture anchor pullout results in decreased bone damage and depends on cortical thickness. Knee Surg. Sports Traumatol. Arthrosc. 29(7), 2212–2219 (2021).
Goschka, A. M. et al. Biomechanical comparison of traditional anchors to all-suture anchors in a double-row rotator cuff repair cadaver model. Clin. Biomech. (Bristol, Avon) 30(8), 808–813 (2015).
Oh, J. H. et al. Pullout strength of all-suture anchors: Effect of the insertion and traction angle—A biomechanical study. Arthroscopy 34(10), 2784–2795 (2018).
Nagra, N. S. et al. Mechanical properties of all-suture anchors for rotator cuff repair. Bone Jt. Res. 6(2), 82–89 (2017).
Elfar, J. et al. Composite bone models in orthopaedic surgery research and education. J. Am. Acad. Orthop. Surg. 22(2), 111–120 (2014).
O’Neill, F. et al. Validity of synthetic bone as a substitute for osteoporotic cadaveric femoral heads in mechanical testing: A biomechanical study. Bone Jt. Res. 1(4), 50–55 (2012).
Battula, S. et al. Experimental evaluation of the holding power/stiffness of the self-tapping bone screws in normal and osteoporotic bone material. Clin. Biomech. (Bristol, Avon) 21(5), 533–537 (2006).
Gardner, M. J. et al. Osteoporosis and skeletal fractures. HSS J 2(1), 62–69 (2006).
Seebeck, J. et al. Mechanical behavior of screws in normal and osteoporotic bone. Osteoporos. Int. 16(Suppl 2), S107–S111 (2005).
Oh, J. H., Song, B. W. & Lee, Y. S. Measurement of volumetric bone mineral density in proximal humerus using quantitative computed tomography in patients with unilateral rotator cuff tear. J. Shoulder Elb. Surg. 23(7), 993–1002 (2014).
Guo, J. et al. Morphological characteristics of the surgical neck region in the proximal humerus at different ages. Eur. J. Med. Res. 27(1), 102 (2022).
Singh, D. et al. Experimental assessment of biomechanical properties in human male elbow bone subjected to bending and compression loads. J. Appl. Biomater. Funct. Mater. 17(2), 2280800018793816 (2019).
Beniak, J. et al. Roughness and compressive strength of FDM 3D printed specimens affected by acetone vapour treatment. IOP Conf. Ser. Mater. Sci. Eng. 297, 012018 (2018).
Kamaruddin, S., Khan, Z. & Wan, K. The use of the Taguchi method in determining the optimum plastic injection moulding parameters for the production of a consumer product. J. Mek. 18, 98–110 (2004).
Gausden, E. B. et al. Subscapularis tendon loading during activities of daily living. J. Shoulder Elb. Surg. 26(2), 331–336 (2017).
Imbergamo, C. et al. Graft augmentation of rotator cuff repair improves load to failure but does not affect stiffness or gap formation: A meta-analysis of biomechanical studies. Arthrosc. J. Arthrosc. Relat Surg. 39(10), 2202–2210 (2023).
Khazzam, M. et al. The effect of age on risk of retear after rotator cuff repair: A systematic review and meta-analysis. JSES Int. 4(3), 625–631 (2020).
Fleischli, J. E. Editorial commentary: Biomechanics of all suture anchors: What We know so far. Arthroscopy 34(10), 2796–2798 (2018).
Er, M. S. et al. Suture anchor fixation strength with or without augmentation in osteopenic and severely osteoporotic bones in rotator cuff repair: A biomechanical study on polyurethane foam model. J. Orthop. Surg. Res. 9(1), 48 (2014).
Barber, F. A. & Herbert, M. A. All-suture anchors: Biomechanical analysis of pullout strength, displacement, and failure mode. Arthroscopy 33(6), 1113–1121 (2017).
Yamauchi, S. et al. Biomechanical analysis of bioabsorbable suture anchors for rotator cuff repair using osteoporotic and normal bone models. J. Orthop. Sci. 27(1), 115–121 (2022).
Ntalos, D. et al. Biomechanical analysis of conventional anchor revision after all-suture anchor pullout: A human cadaveric shoulder model. J. Shoulder Elb. Surg. 28(12), 2433–2437 (2019).
Ntalos, D. et al. Conventional rotator cuff versus all-suture anchors—A biomechanical study focusing on the insertion angle in an unlimited cyclic model. PLOS ONE 14(11), e0225648 (2019).
Rosso, C. et al. Three anchor concepts for rotator cuff repair in standardized physiological and osteoporotic bone: A biomechanical study. J. Shoulder Elb. Surg. 29(2), e52–e59 (2020).
Wang, L. et al. Why do woodpeckers resist head impact injury: a biomechanical investigation. PLoS One 6(10), e26490 (2011).
Funding
This research was supported by a grant of the Korea Health Technology R&D Project through the Korea Health Industry Development Institute (KHIDI), funded by the Ministry of Health & Welfare, Republic of Korea (Grant Number: HR20C0026).
Author information
Authors and Affiliations
Contributions
K.H.K. and N.K. as corresponding authors, reviewed the comprehensive data and contents of the paper. J.S. participated in the experiment and reviewed the experiment’s data. J.O. as first authors wrote the paper and participated in the experiment, and reviewed the data.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Ock, J., seo, J., Koh, K.H. et al. Comparing the biomechanical properties of conventional suture and all-suture anchors using patient-specific and realistic osteoporotic and non-osteoporotic phantom using 3D printing. Sci Rep 13, 20976 (2023). https://doi.org/10.1038/s41598-023-48392-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-48392-y
- Springer Nature Limited