Abstract
This study explores the seismotectonics of Kachchh in western India, a region with a low-to-moderate strain rate and a history of significant earthquakes, notably the 1819, Mw 7.8 Allah Bund, and the 2001, Mw 7.6 Bhuj. Despite its substantial seismic risk, comprehensive studies on Kachchh’s seismogenic sources are scarce. This is attributed to the concealed nature of active structures, hindering definitive age constraints in paleoseismological research. Our research comprises a detailed paleoseismic analysis of the north-verging, reverse Jhura Fault underlying the Jhura anticline, a segment of the Kachchh Mainland Fault. This fault segment shows evidence of surface-rupturing earthquakes in the area south of the Great Rann of Kachchh. The investigation reveals three paleoseismic events: Event I before 9.72 ka B.P., Event II between 8.63–8.20 ka B.P., and Event III between 6.20–6.09 ka B.P. The elapsed time since the last event on this fault is > 8000 years, suggesting that the area is exposed to a significant earthquake hazard. This highlights the need for more precise characterization of individual seismogenic sources for future earthquake preparedness.
Similar content being viewed by others
Introduction
The 2001 Bhuj earthquake (Mw 7.6), which caused about 20,000 causalities, more than 150,000 homeless people, and USD 42.55 million in economic loss, increased attention to the anomalous seismicity of the Kachchh peninsula (NW India). This led to the surge of studies to decipher the seismotectonic framework of this area that also experienced the 1819 Allah Bund (Mw 7.8) and the 1956 Anjar (Mw 6.0) earthquakes (Fig. 1)1.
Most active tectonics and paleoseismological research in this low-to-moderate strain rate intraplate region was focused on the 80–90 km long primary surface rupture and widespread seismically induced liquefaction features induced by the 1819 event2,3,4,5,6,7,8,9,10. Moreover, studies following the 2001 event focused on identifying its causative fault using aftershocks relocation, remote sensing, gravity data, and geodetic monitoring11,12,13,14,15,16,17,18,19,20,21,22. These studies reported an E-W striking, south-dipping thrust fault with a coseismic slip of up to 10 m, confined between 10 and 30 km of depth11,12,13,14,15,16,17,18,19,20,21,22,23. Further, studies on the coseismic surficial deformation of 2001 earthquake, reported probable occurrence of a 0.8 km long primary fault scarp with a dextral component on the Manfara Fault (MF), along with widespread liquefaction and lateral spreading features24,25,26.
The two major Kachchh events (1819 and 2001) had a similar magnitude and secondary deformation, but strikingly different surface rupture lengths9,10,27,28,29,30,31,32,33,34. Such difference in surface rupture length between earthquakes that occurred to the North and the South of the Great Rann poses a significant gap in the understanding of the seismotectonic framework of Kachchh and raises an important question, whether the active faulting may occur along structures with different geometrical characteristics? To address this gap, attempts were made in the form of active fault mapping and paleoseismological trenching along Kachchh Mainland Fault (KMF), Katrol Hill Fault (KHF) and South Wagad Fault (SWF) (Fig. 1b).
The first active fault map was published in 2001, which reported active fault traces along the KMF28. Later, the only study from the SWF by Malik et al. (2017)35, reported a well-preserved deformation zone on a north-dipping thrust fault with three paleoearthquakes. However, the remaining active faults and paleoseismic studies lacked in different ways, especially because evidence of paleo-earthquakes were reported based on liquefaction features, which are secondary evidence related to seismic shaking and may not be very useful for identifying causative faults in the complex tectonic setting of the Kachchh basin9,10,33. Further, a series of trenches excavated across the KMF and KHF revealed surface rupturing earthquakes on the south-dipping fault during the Late Pleistocene, but without age constraints29,31,32. Kothyari et al. (2021)34 explored the western segment of the KMF and unearthed six paleo-earthquakes from six trenches. These findings raised questions about the wide-depositional hiatus retrieved in those trenches (i.e., Mesozoic sandstone directly overlain by 10 ka old calcareous sands), and questions the rheology of the layers for arresting such vertical faults. For example, the tendency of a fault to propagate through a medium, with a slip, and the influence of near-surface geology on such behaviour is a primary parameter that can potentially obscure the evidence of surface faulting both in geomorphology and in exploratory trenches36,37.
Based on the above-mentioned observations, there still remain the following open questions: (a) Can large surface-rupturing events, comparable to the 1819 Allah Bund earthquake, also occur south of the Great Rann? (b) Can these events be constrained using paleoseismology in the late Holocene or Pleistocene and even beyond? (c) Can paleoseismology confirm that Kachchh is among the most active intraplate region worldwide? To address these issues our study involves paleoseismic and morphotectonic analyses on the Jhura Fault (JF), a south-dipping branch of the Kachchh Mainland Fault (KMF) that demarcates the northern boundary of the Jhura Anticline (JA), extending laterally for 15–20 km. This section of the KMF exhibits north-facing active fault scarps that separates older and younger alluvium (Fig. 2). We utilised satellite imagery, photogrammetry, and field data to map the active fault trace, and identified four trenching sites for paleoseismic investigation, dating three paleo-ruptures. Through trishear kinematic inverse modelling, we assessed the fault and fold growth, comparing recent movements to the overall displacement. The present study along JF highlights surface rupturing events, updates the seismic event catalogue, and evaluates earthquake recurrence of the Kachchh region in a global intraplate context.
Geologic and tectonic setting
The Kachchh intracratonic rift basin formed during the breakup of Gondwanaland in the Late Triassic and lies in the western part of the Indian plate. Its geological evolution, encompassing the breakup, drifting, and collision of the Indian Plate with the Eurasian Plate, involves three key tectonic events40,41,42,43,44,: (i) a Late Triassic rifting phase40; (ii) an Early Jurassic to Late Cretaceous divergent phase40,45,46; and (iii) a post-rifting transpressional phase since the Tertiary 40,46,47. The basin is divided into distinct geomorphic zones, including a coastal zone, the central rocky uplands (Kachchh and Wagad Uplands), the Banni-Plain, the Island belt (Pachchham, Khadir, Bela and Chorar), and the saline-waste lands of the Great and Little Rann 48 (Fig. 1).
GNSS velocity data reveals an NW–SE oriented shortening in the Kachchh area49 of ~ 3 mm/year, with the principal horizontal stress (SHmax)50 direction varying from NW–SE to NNE-SSW. The main active structures of Kachchh are the KMF, the SWF, and the ABF bordering the Great Rann to the south and to the north, respectively, which, according to Gahalaut et al. (2019)49, should be characterized by a dip-slip rate of ~ 4–6 mm per year (Fig. 1)49.
Historically, the 1819 Allah Bund earthquake was the most significant event, creating a 80–90 km long fault scarp with variable height of 4–6 m4,5. Its magnitude, estimated to be between Mw 7.6 and Mw 8.2, is debated due to limited data on uplift and subsidence3,5,8,35,48,49. The 1956 Anjar earthquake (Mw 6.1), originated near the JA, probably along a segment of the KMF, at the northern boundary of the Kachchh upland (Fig. 1)3,5,8,51,53.
Instrumental seismicity in the region has been notably characterized by the earthquake swarms around the Bhuj epicentral area since the major 2001 event35. Seismological data from 2000 to 2020 includes several earthquakes with magnitudes ranging from Mw 4 to the main shock of Mw 7.6, with focal depths ranging between 10 and 40 km, primarily near the KMF and SWF 46,54,55.
The JA lies in the middle of the KMF at an elevation of 300 m above m.s.l. and with a core characterized by the outcrop of Mesozoic rocks, with Tertiary and Quaternary successions covering the anticline limb to the north (Figs. 2, 3; and refer main map Srivastava et al., 2023 for lithological contacts44). Deeply incised V-shaped valleys, tight meanders, strath terraces and a prominent E-W to WNW-ESE ranging fault scarp highlights a significant tectonic forcing in its recent landscape evolution44,52,53,54,55. The fault scarp displaces recent alluvial fans and river terraces across the Kaila River (Figs. 2 & 3). Additionally, it cuts the Jurassic sandstones that dip steeply at 70–80° to the southwest, and sub-vertically dipping Tertiary beds (Figs. S1a,b).
Recent studies on this structure, propose that it is underlined by a 15°, south-dipping thrust fault, that was characterized during the last event by more than 5 m of slip accommodated by drag folding in young alluvium at shallow depths31.
Data and methods
Dataset gathering and computation
The geological and geomorphological information involving the structural data, geomorphic landforms and the diverse lithological outcrops was obtained through remotely sensed datasets (CARTOSAT-I, 2005–2006: Indian government web portal, https://bhuvan.nrsc.gov.in/home/index.php), official maps (Fig. 1)9,29,30,31,33,34,45,46,48 and field surveys. Data related to historical-instrumental earthquakes were gathered from multiple sources such as the USGS (https://earthquake.usgs.gov/earthquakes/search/), the International Seismological Center (ISC; http://www.isc.ac.uk/iscbulletin/search/catalogue/), and from the Institute of Seismological Research (ISR), Gandhinagar catalogues30. The focal mechanisms in Fig. 1 are from the Global CMT Catalogue (https://www.globalcmt.org/). The stress indicators consisting of horizontal maximum (Shmax), minimum (Shmin), and vertical (Sv) stress directions are from the World Stress Map (WSM) project (https://www.world-stress-map.org/; Fig. 1)50,57. Lastly, the GPS velocities in Fig. 1 are from Gahalaut et al., (2019)49.
The declassified CARTOSAT-I panchromatic satellite imagery with stereo vision capability, obtained from the National Remote Sensing Centre (NRSC) (https://www.isro.gov.in/Spacecraft/cartosat-1), has a resolution of 2.5 m and the data was acquired during the 2005–2006 mission. The CARTOSAT-1 satellite acquire two images, one with forward looking (Fore) camera, and another by after (Aft), which are at tilt angles of + 26° and − 5°, respectively. Each imagery set comes with its respective predetermined Rational Polynomial Coefficients, based on their unique orbit and attitude models. These coefficients facilitate the acquisition and metadata necessary for correcting geometric distortions in the imagery38,39. Using these images and following the methodology of Evans et al., 200857 we employed the ENVI 4.7 software, for generating a Digital Surface Model (DSM) and a 3D Anaglyph (3DA), both characterized by a geometric resolution of roughly 3 m.
The study area was also surveyed using a UAV DJI Phantom 4 pro. It is a quadcopter equipped with an internal sensor of ½0.3″ CMOS, FOV 94° 20 mm (35 mm format equivalent) f/2.8 focus at ∞ lens and operated by a remote control boarded with a mobile device, which has the respective commercial application for mapping such as Pix4D mapper. This survey allowed to produce Hi-Res photograph mosaic for data visualization and geomorphic interpretation.
We started field survey investigations, acquiring multiple ground-penetrating radar profiles. Following the common midpoint approach, the electromagnetic waves provided indications of tectonic perturbations in the subsurface58. Optical Stimulated Luminescence (OSL) samples were collected using stainless steel tubes hammered into a clean vertical sections for sample locations. Thereafter, samples were processed at the luminescence facility at IIT Kanpur equipped with the Frantz magnetic separator, the Risø TL/OSL reader and the hyper-pure germanium detectors (HPGe) gamma-ray spectrometer59.
Geomorphic mapping and topographic analyses
Using 3DA and the Hi-Res photograph we mapped the main morphotectonic feature of the study area. Furthermore, we validated the produced thematic maps through field surveys conducted in the time frame starting from January-2015 to July-2018.
Topographic analyses were performed using the terrain profile plugin in QGIS and the MATLAB. Employing this DSM as input data, we used a script to calculate the Vertical Separation (VS) between the hanging wall and footwall block surfaces along the JF trace, following the workflow proposed by DuRoss et al. (2019)60. To be sure that we took into account the tectonic forcing in the topographic signal we extracted twenty-two topographic profiles across the mapped Jhura Fault scarp. To do this we also considered the previously detected geomorphic feature with the best preservation and the sparsest vegetation detected also in the Hi-Res photographs and 3DA. Finally, to correlate the long-term deformation with the short-term one we also extracted a topographic swath profile along the strike of the whole JA using the TopoToolbox library61.
Trenching and optical stimulated luminescence dating
The paleoseismological trenching was conducted during October–November 2016 and 2017 to identify the signatures paleo-earthquakes along this segment of KMF. The trenching sites were selected considering the scarp profiling, the exposed zone of deformation demarcated by the vertically stacked Tertiary and Mesozoic succession, suggesting propagation of active faulting further north, and, in addition, the high-resolution, subsurface information derived from the GPR profiles (Figs. 3 and 4, and Supplementary Data Figs. S1a-e and S3). We excavated four trenches: one at the base of the fault scarp and the other three on top of a gently sloping surface. Following this, we prepared a trench log for each excavation, which included a description of the lithology, grain size, colour, bedding, and tectonic structures. Photo-mosaics of the trench walls were also prepared and overlaid on the trench log with the embedded information for improved visualization.
For constraining the age model of the sedimentary sequence, we collected twenty-three samples from the exposed succession of both the trench walls and used the OSL dating technique. Quartz grains (90–150 μm) were selected under controlled laboratory conditions. The extraction involved chemical treatment with 1N HCl and 30% concentrated H2O2 that helped remove carbonates and organic matter. Thereafter chemically treated sediments were magnetically separated from heavy minerals and feldspar and isolate quartz grains. HF treatment was done to remove any remanent feldspar, and then the sample was rinsed with HCl to remove any HF acid-induced fluorite precipitate from the isolated quartz62,63,64. To determine the equivalent dosage (De) of these extracted quartz samples, the traditional single-aliquot regenerative dose (SAR) methodology was used63,65.
Following the preparation, eight out of the twenty-three samples, were not further considered for dating. Samples were processed only if they showed a bright quartz signal and a fast component-dominated decay shine-down curve, along with if the recycling and recuperation ratio values deviated by less than 10% and 5%, respectively, from unity63. After the De estimation, the dose rates were measured for all samples and was tuned to account for moisture attenuation as obtained in the laboratory. When normalized for field saturation, the water content of a dehydrated and saturated material is referred to as the lifetime water content at burial time (Table 1). Furthermore, the quantification of the impact of cosmic rays on the ultimate dose rate was determined following the methodology established by Prescott and Hutton (1995)66.
Kinematic modelling and magnitude computation
To achieve a broader view of the geologic structures and their related deformation, we built a shallow geologic cross-section composing the information acquired in the dug trenches.
We restored the composite section through a trishear kinematic model considering the observable offset and deformation of the stratigraphic units and the associated folding in the hanging wall (Fault Fold code67,68). Additionally, the trishear kinematic inversion output also allowed the investigation of the velocity of fault propagation through the overlying stratigraphy since the fold geometry depends on the propagation on the slip ration (P/S value).
To minimize computing time, we performed our search in successive steps: firstly, making evaluations over large regions of values and then focusing over smaller ranges, testing small increments in parameter values such as ramp angle, fault tip position and propagation to slip ratio (P/S). We tuned the trishear parameters manually for the faults characterized by a small amount of displacement and folding. In contrast, for the not fully exposed faults we employed an inverse grid search of the trishear parameters, especially those not directly constrained by the trench exposure. The fold limb has been unfolded by keeping the amount of P/S computed during the previous steps, and we moved the fault ramp angle and tip position to restore the visible horizons to a nearly horizontal geometry. For a complete description of the tested models, the grid search runs, and the ranges of the tested parameters refer to the Supplementary Material (Figs. S4–S7 and Tables S1 and 2).
We finally used the age constrained events, the fault trace length and the dip angle obtained from kinematic reconstruction, the observed and computed slip, the calculated rupture area and a literature seismogenic thickness of 30 km, for computing the expected magnitude through well-known empirical relationships69,70.
Results
Main morphotectonic features
In the piedmont zone of the JA, three levels of Alluvial Fan Surfaces (AFS 1–3) were identified (Fig. 2). AFS-1 is located on the hanging wall side of the JF, while AFS-2 and AFS-3, along with multiple river terraces, were observed on the footwall side. Only remnants of AFS-2 crop-out at higher level compared to AFS-3 near the Kaila River valley outlet (Fig. 2c). Differentiating AFS-2 from AFS-3 was challenging due to vegetation and small channels, requiring reliance on quantitative 3DA analysis. Additionally, four levels of fluvial fill and cut terraces were observed along the Kaila River in the eastern part of the JA (Figs. 2a, c).
The outcropping JA extends approximately 16 km in the WNW-ESE direction (Fig. 2b). Conversely, the active fault scarp observed only for about 10 km, most likely because of poor preservation and human modifications such as construction of ponds on the upthrown side of a road (Fig. 3b). Notably, the scarp is better preserved where it displaces one of the mapped AFS (Figs. 2b, 3a-b).
The vertical offset (VS) across the ~ 10 km fault scarp north of the JA varies from 4–15 m across different alluvial fan surfaces, peaking near the central part at about 5 km along the profile (Figs. 3c and S2). Additionally, a minimal offset of 0.5–1 m in AFS-3 suggests the presence of a fault splay in the footwall of the main fault in VS profiles FS-2 and FS-4, although this was obscured by agricultural activities (Figs. 3d and S2). The longitudinal swath profile of JA shows a maximum relief of around 300 m above m.s.l., with the SE portion being steeper (Fig. 3c). The comparsion of VS and elevation profiles reveals about 1 km south-eastward shift in the maximum values of the scarp height relative to the topographic peak. The highest topographic points align with the minimum scarp height, followed south-eastward by increasing VS. Finally, both distributions exhibit a right skewness, more pronounced in the VS values (Figs. 3c and S2).
Trench stratigraphy and structural features
Trench-I
A 6-m-long, 2.5-m-deep, and 3-m-wide trench (location: 23°25′40.86" N, 69°36′57.14" E; WGS84; Figs. 3b, 4 and S1b) was excavated at the base of the fault scarp, just ahead of a pond that exposes overturned Tertiary beds.
The trench stratigraphy (Fig. 4) consists of five units of near vertical Tertiary beds (T1–T5) capped by Quaternary deposits (a1’). The T1 unit consists of micaceous sandstone and is separated from unit T2 by a south-dipping reverse fault (57°) flattening upward. Unit T2 is formed by marly clay comprising a heavily fractured siliciclastic layer. The near-vertically dipping T3 unit comprises siltstone crushed due to intense tectonic deformation. The T4 unit comprises ferruginous mudstone, and T5, in the extreme north of the trench, consists of deformed sandstones (Fig. 4). The overlying Quaternary deposits are formed by the older alluvium that belongs to AFS1, dominated by angular pebbles attesting the short-distance sediment transport from a nearby source (Fig. 4).
Trench-II
A 12 m long, 2–3 m deep, and 3.5 m wide trench (location: 23°25′41.26"N, 69°36′57.63"E; WGS84; Figs. 3b and S1c). The walls of the excavated trench (Fig. 5) exposed gently dipping layers of unconsolidated sand and gravel, displaced by several south-dipping thrust splays. The exposed succession in the east wall of Trench-II has been divided into five units (labelled from a to e; Fig. 5b). The sediments composing these units are overbank alluvial deposits emplaced during successive flood cycles, and typically exhibits a fining-upward sequence. In particular, units a1 to c represent an upward fining sequence ascribable to individual flood cycles. The coarser sediments at the bottom consist of matrix-supported fine gravel, gradually grade upward to coarse sand. Unit c4 is partly eroded on top of the hanging wall of fault F2, indicating an erosive phase postdating c4 and predating the following depositional cycle. The overlying units d and e are made of medium sand to silt deposited in an overbank environment. The sequence shows a diverging geometry and host a fault-propagated-fold near the fault tip along with the dragging of units resulting in local recumbent folding (Fig. 5). The fault strands displacing these units show a progressively lower dip moving northward.
The strands F1b and F1c (in the southern portion of the trench) displaced units a1-a3 and are sealed by unit b, whereas the fault strands F2a and F2b deformed units a1-a3 (the displaced a1 is not exposed in the trench), b, c1-c4 and d1-d5. However, F2b accommodates much more displacement with multiple rupture events as the offset from a3 to c3 registers displacement of ~ 60–70 cm compared to ~ 10–20 cm of offset in d1 to d4 units. The F2a records a little slip ranging between ~ 5–15 cm. In the southern bottom portion of the trench, the strand F3a marks deformation displacing c1-c4, d1-d3 and d5 by ~ 60 cm. Deformation along the strand F3b shows a distinct thin layer of mixed material indicative of a shear zone comprised of overturned units dragged during slip along the fault (Fig. 5).
Similarly, the west wall was classified following the same unit code as the east wall (Fig. S8a-b). However, the units with a and d codes were subdivided into more sub-units, i.e., a1’-a3 and d1-d5, and few units in the west wall are thicker that the correlated counterparts on the east wall (Figs. 5b and S8a-b). As far as the structure is concerned, the west wall has more tilting and warping in the layers than the east wall, and the fault strands are evident, with at least the latest event displacing all the beds by the same amount causing the propagation of the fault at the surface.
Trench-III
The further excavation of Trench-II was obstructed by an underground water pipeline. Therefore, looking for the deformation on fault F3b, Trench-III was excavated next to T-II after leaving a gap 2 m (Figs. 3b and S1d). The excavated trench was 7 m long, 2–3 m deep, and 3 m wide (location: 23°25′41.47"N, 69°36′57.73"E; WGS84; Fig. 3b), and it revealed a thick sequence of overbank deposits, stratigraphically placed on top of unit d3 (Fig. 6). From the base, a thick sandy layer with medium-coarse gravel intercalations, coded as d5’, is partly overlain by the unit d5 and by another event of overbank deposition (unit d6). These units are capped by unit d7, a medium to coarse gravel embedded in unconsolidated sand, reflecting a high energy transport. On the top, the continuation of the e2 layer was laterally followed from Trench-II toward this one (Fig. 6).
The depth of the trench was maintained to 2–3 m to preserve the safety conditions of the working people under unstable trench walls.
Trench-IV
This trench was located ~ 70–80 m west of Trench-II (23°25′43.51"N, 69°36′54.72"E WGS84; Fig. 3b), collapsed shortly after the excavation. Initial investigation of the partially cleaned east wall revealed a south-dipping reverse fault, with another fault strand near the base (Figs. S1e and S9). To view it properly, further excavation was planned but led to wall collapse.
An overall view of the fault zone was obtained through a composite section built along the dug trenches (Fig. 7). Later we used this composite trench log to restore the deformation history of the fault across the entire deformation zone.
Trench retro-deformation
The initial step of the trishear retro-deformation started from the present geometry, reconstructed in the composite trench log (Fig. 7). We first simply applied a retro-deformation of the offsets identified in the trenches, obtaining 0.85 m of horizontal shortening for Event III, and 1.15 m and 0.64 m for Event II and I, respectively (Fig. 8). For the Event I and unit d3 (Step 0, Fig. 9a), the retro-deformation performed through an iterative change approach in the P/S value resulted in an optimal P/S = 2 and obtained a fault propagation of 1.16 m with a slip of 58 cm (Step 1; Fig. 9b). Considering Event II, after testing more than 100,000 models, we first restored the offset measured in the different units, obtaining 48 cm of slip (Step 2; Fig. 9c), then unfolded Unit a3 to restore the F2 fault-propagation folding during Event II (Step 3; Fig. 9d). The outcoming parameters are a P/S = 5, and a total slip during this last phase of fault growth of ca. 3.5 m. These parameters imply a fault propagation of ca. 17.4 m, reaching a depth of ca. 7 m below the top of the trench where F2 intersects F1 (Fig. 9d). Finally, the fold front limb, that is representative of the cumulated, long-term activity of the JF, has been unfolded through the trishear restoration of Fault F1, resulting in a total slip of 11 m and propagation of the fault tip of 55 m, reaching a depth of ca. 65 m (Step 4; Fig. 9e).
This last retro-deformation includes Event I, and probably other older events with no dated units in the trenches that can help in constraining the age of the events.
Age constraints of paleo-earthquakes
We dated the logged units from fifteen out of twenty-three collected samples. The dated samples provide critical information on the sequence of paleo-events from this area. The OSL ages derived from both the east and the west walls of the Trench-II, combined with the stratigraphic interpretation and retro-deformation, indicates at least three significant Holocene paleo-earthquakes along this segment of the KMF (Figs. 5, S10–S13 and Table 1). However, the older event may be a compound of multiple events, as suggested by the retro-deformation analysis (refer Sect. 4 in Supplementary Data).
Based on the cross-cutting relationships, slip and folding observed in the exposed sedimentary units on the east wall of the Trench-II, as well as their OSL ages, we infer that the surface faulting events were caused by a slip on the JF (Figs. 5, 8 and 9). The oldest Event I, along with potentially earlier events that caused deformation and folding and displacement along the F1a-c strands (Fig. 5b). The Event I folded and displaced units a1-a3, followed by a phase of erosion and deposition of unit b. The penultimate Event II occurred after the deposition of units c3-c4 and before the deposition of unit d1. Considering ages only from the east-wall, it is suggested that Event II occurred between 8.63 ka and 7.11 ka BP (Figs. 5 and 8c). Further, the deposition continued from unit d1 to unit d5. Unit d1 deposited after the erosion of Unit c4 in the hanging wall of fault F2b. The latest Event III (Most Recent Event—MRE) took place after the deposition of unit d5 and before the deposition of unit e2 (Figs. 5 and 8b). MRE was registered by F2b with a minor slip along F2a, as well as along F3a strands. But most likely, F3a and F3b moved displacing the younger sucession (Unit d5) during Event III (Fig. 7).
Based on the OSL ages from the east wall we suggest that Event III (MRE) occurred between 6.42 ka and 6.09 ka BP (Fig. 5a,b). Conversely, the stratigraphy of the west-wall highlights the occurrence of just two events because the deformation was taken up mostly by folding, rather than faulting (Fig. S8). Due to erosion of the upper portion of unit c2 followed by capping (deposition) of unit e1, there is no reliable constraints on the amount of offset for the younger units. Further, the folding associated with faulting prevented us identifying possible successive events on F1W. Therefore, the F2aW and F2bW strands were considered for bracketing the age of the events. Considering the ages from the west wall, we infer that the penultimate Event II occurred between 8.67 ka and 8.23 ka, and the MRE in between 6.21 ka and 4.33 ka (Fig. S8). The MRE led to the reactivation of F1w and activation of new fault strands, which in our log are named F2aW and F3W. The deformation on the east-wall of Trench-II, suggests that the number of events might be more than three. Furthermore, the OSL ages from the west-wall were also considered to better constrain the events. With the similar identification of layers based on lithologies, the Event-II was bracketed between 8.63 ka and 8.23 ka and subsequently the Event III (MRE) between 6.20 ka and 6.09 ka (Figs. 5b and S8).
Expected fault magnitude
The fault parameters derived from field mapping (anticline and fault scarp length), and the data retrieved from the paleoseismological trenches about the displacements related to the paleo Events II and III are listed in Table 2. This data was used for calculating the expected moment magnitude of future earthquakes generated by the JF. For these calculations we applied empirical relationships from Wells and Coppersmith (1994, WC-94) and Leonard (2014, L-14), considering the mapped lengths of the anticline and fault scarp as possible extents of surface faulting events. We excluded Event I from the calculation because of the limitation with the ages and possible cumulative deformation as evidenced in the retro-deformation.
Considering the length of the anticline with WC-94 and L-14 methods, the estimated magnitude ranges between 6.3 and 6.5. For the fault scarp’s length, magnitudes are slightly lower, from 6.1 to 6.2. If we consider dislocations from Events II and III as average displacements, magnitudes range from 5.8 to 6.4. These calculated magnitudes, based on fault length and event offsets, are comparable within uncertainties, indicating the fault's consistent behavior in the long- and short-term. Conversely, using the ca. 3.5 m slip derived from unfolding of the deformed units associated to Event II, would yield a magnitude range between 6.8 and 7.6 (Table 2). This higher estimate seems unrealistic, because according to L-14 empirical relationship a fault over 50 km long would be required to generate an earthquake with magnitude between Mw6.8 and 7.6, contradicting the 16 km length of the mapped anticline.
Discussion
Short-term and long-term effects of surface rupturing
We found evidence of at least three surface-rupturing earthquakes along the JF, a branching out fault of the KMF system that borders the southern portion of the Great Rann of Kachchh. In each trench excavation, the one excavated across the fault scarp to the other two dug further ahead in the foreland, it was possible to observe the foreland propagation of the deformation, characterized by a reduction in the dip-angle of the fault splays (Figs. 4, 5, 6 and 7). Moreover, the stratigraphic logs and OSL ages suggest that each earthquake caused a deformational shift towards north in the Banni Plain, resulting the activation of new fault splays and occasionally the reactivation of older fault strands. The total measured slip is approximately 11 m, leading to a cumulative uplift of 13.6 m, which closely matches the observed maximum fault scarp height of 13.98 m (Fig. 3d; Profile FS-3).
Topographic and paleoseismic investigations on the JF revealed the evidence of tectonic activity during Holocene. The similarity between the height of the fault scarp and the relief wavelengths of the anticline suggests that both long-term topography and short-term deformation are driven by the same processes, indicating that the topography closely reflects cumulative deformation on fault (Fig. 3c). Despite observing a right skewness in the VS distribution—potentially due to factors like fault complexity, lithological differences, fault slip kinematics, slip distribution, or erosion—the alignment of the VS distribution with the anticline's topography highlights a substantial continuity between the short-term and the long-term fault behaviour71,72.
Updating seismic catalogue
Previous studies in the Kachchh basin have identified multiple paleo-earthquakes. Rajendran and Rajendran (2001)9 based on paleo-liquefaction features linked an event between 875–1035 CE near the 1819 source to historical accounts of an 11th-century earthquake that destroyed Brahminabad north of the ABF scarp. Paleoseismological studies on the secondary ruptures and liquefaction around 2001 Bhuj epicenter suggested two earlier events around 4000 and 9000 years ago33. Trench studies on the SWF identified three prehistoric earthquakes: one before 6972–6666 BP, another between 4753–4149 BP, and the most recent between 2109–1913 BP 30..
Kothyari et al. (2021)34 discovered four Late-Middle Holocene events from trenching on the KMF’s western segment, occurring between 2000–2900 years BP, 3500–3800 years BP, 4000–4600 years BP, and the most recent between 890–1800 years BP, possibly associated to the 11th-century event. At the archaeological site of Dholavira, close to Khadir Island, a settlement had existed for about 1500 years (3450–4950 years BP), and an earthquake damaged it sometime between 4150–4450 years BP (Fig. 1 for location)73. Thus, this event can be correlated with an event between 4753–4149 BP identified along the SWF, as well as with the one identified in the liquefaction study from the 2001 epicentral area30,33 (Fig. 1).
Our study adds three new surface rupturing events: Event I before 9.72 Ka BP; Event II between 8.63–8.20 ka BP; and Event III (MRE) between 6.20–6.09 ka BP, expanding the paleo-event catalogue. Estimated magnitudes from offsets in trenches range between Mw 6.0–6.4 for Event III, and Mw 5.8–6.4 for Event II. However, the 3.5 m slip obtained from unfolding the Event II implies a 50 km long rupture, which is not observed from the morphometric expression of the fault scarp bordering the JA. Hence, the modelling result poses an open question regarding the possibility that the deformation observed in the trenches may have resulted from a cumulative slip of more than one earthquake, or that the earthquake ruptured multiple segments of the KMF. On the contrary, Event III correlates well with the mapped fault scarp length and the observed offset, most likely confined to JF.
Recurrence interval in intraplate regions
Many thorough paleoseismic studies have been conducted in different continental interiors, including the Rhine graben in Germany, the Bohemian Massif in Czech Republic, Central Asia, Australia and the New Madrid in the USA, have identified the evidence of paleo-earthquakes having recurrence intervals (RI) from a thousand to over ten thousand years74,75,76,77,78,79,80,81,82,83,84,85,86. Based on the evidence of paleo-earthquake identified in our trenches as well as the previous paleoseismic studies (Table 3), we suggests that the Kachchh is one of the most seismically active intraplate regions in the world having RI of about 2000 years9,33,34,35. This is also consistent with the short-term convergence rate of ~ 3 mm/year reported from the continuous GPS measurement from the Kachchh and its adjoining areas49.
Considering the return period and paleoseismological results, it is quite logical to suggest that the JF portion has temporal earthquake clustering. This includes one or more events nucleated before 9.72 ka, as observed from a cumulative fault scarp. Notably, Events II and III occurred within a relatively shorter span of 2000 years, and since then no earthquake has been experienced as observed from the trench investigation. Possibly, this can be explained hypothesizing two scenarios: (1) the stress may have been transferred to the neighbouring segments that generated younger events, or (2) more recent seismic events may have not been identified in our trenches due to removal of sediment succession AFS2 by erosion. If these scenarios are not true, then possibly the stress accumulated along JF since the last event hints towards having a major earthquake in near future.
Conclusion
This study provides key insights about the seismo-tectonics of the Kachchh region, uncovering significant surface faulting paleo-earthquakes along the Jhura Fault (JF)—a branching out fault of the Kachchh Mainland Fault (KMF), with magnitude ranging from Mw 6.0–7.5, in the vicinity of the 2001 Bhuj earthquake. With a RI of ~ 2000 years the Kachchh region can be placed as one of the most active intraplate regions in the world. The 10–16 km long active fault scarp along Jhura Fault (JF) bordering the Jhura Anticline (JA) and varying offsets observed in the paleoseismic trenches are indicative of coseismic surface ruptures associated with major paleo-earthquakes triggered by stress transfer across the adjacent segments of KMF.
Given the above insights, we emphasize that further comprehensive research on long-term deformation is required to understand the tectonic behaviour of active faults and associated fault segments of KMF.
Data availability
The dataset, involving images and mosaics of the trenches along with Optically Stimulated Luminescence (OSL) data and curves, and the results of Inverse grid search from Kinematic restoration, are provided in the supplementary sheet. The remotely sensed datasets (CARTOSAT-I, 2005–2006) can be accessed from the Indian government web portal: https://bhuvan.nrsc.gov.in/home/index.php. Historical and instrumental earthquakes were gathered from USGS: https://earthquake.usgs.gov/earthquakes/search/; ISC: http://www.isc.ac.uk/iscbulletin/search/catalogue/; and from the Institute of Seismological Research (ISR), Gandhinagar catalogues. The focal mechanisms are from the Global CMT Catalogue: https://www.globalcmt.org/. The stress indicators are from the World Stress Map (WSM) project and can be accessed at https://www.world-stress-map.org/. All intermediate data processing and calculations generated and analysed during the current study are available from the corresponding author upon request.
References
Saraf, A. K. & Choudhury, S. Cover: NOAA-AVHRR detects thermal anomaly associated with the 26 January 2001 Bhuj earthquake, Gujarat, India. Int. J. Remote Sens. 26, 1065–1073 (2005).
Burnes, A. XXXVII. Memoir on the Eastern Branch of the River Indus, giving an Account of the Alterations produced on it by an Earthquake, also a Theory of the formation of the Runn, and some Conjectures on the Route of Alexander the Great; drawn up in the years 1827–1828. Trans. R. Asiat. Soc. G. B. Irel. 3, 550–588 (1834).
Oldham, T. A Catalogue of Indian Earthquakes from the Earliest Time to the End of AD 1869 (governor general of India in council, 1883).
Oldham, R. D. A note on the Allah Bund in the north west of the Runn of Cuch. Mem. Geol. Surv. India 28, 27–30 (1898).
Oldham, R. D. The Cutch (Kachh) Earthquake of 16th June, 1819: With a Revision of the Great Earthquake of 12th June, 1897 Vol. 46 (Central Publication Branch, 1926).
Sohoni, P. S. & Malik, J. N. Remnants of large magnitude earthquakes: Evidences from the Great Rann sediments, Kachchh, Western India. Curr. Sci. 985–989 (1998).
Malik, J. N., Sohoni, P. S., Karanth, R. V. & Merh, S. S. Modern and historic seismicity of Kachchh Peninsula, western India. Geol. Soc. India 54, 545–550 (1999).
Bilham, R. Slip parameters for the Rann of Kachchh, India, 16 June 1819, earthquake, quantified from contemporary accounts. Geol. Soc. Lond. Spec. Publ. 146, 295–319 (1999).
Rajendran, C. P. Characteristics of deformation and past seismicity associated with the 1819 Kutch earthquake, Northwestern India. Bull. Seismol. Soc. Am. 91, 407–426 (2001).
Rajendran, C. P. & Rajendran, K. Historical constraints on previous seismic activity and morphologic changes near the source zone of the 1819 Rann of Kachchh Earthquake: Further light on the penultimate event. Seismol. Res. Lett. 73, 470–479 (2002).
Rastogi, B. K. et al. The deadliest stable continental region earthquake occurred near Bhuj on 26 January 2001. J. Seis, 609–615 (2001).
Negishi, H. et al. Size and orientation of the fault plane for the 2001 Gujarat, India earthquake (Mw7.7) from aftershock observations: A high stress drop event. Geophys. Res. Lett. 29, (2002).
Hough, S. E. The 26 January 2001 M 7.6 Bhuj, India, earthquake: Observed and predicted ground motions. Bull. Seismol. Soc. Am. 92, 2061–2079 (2002).
Antolik, M. Rupture process of the 26 January 2001 Mw 76 Bhuj, India, Earthquake from teleseismic broadband data. Bull. Seismol. Soc. Am. 93, 1235–1248 (2003).
Bodin, P. Source parameters and tectonic implications of aftershocks of the Mw 7.6 Bhuj earthquake of 26 January 2001. Bull. Seismol. Soc. Am. 94, 818–827 (2004).
Gahalaut, V. K. Constraints on the Source Parameters of the 26 January 2001 Bhuj, India, Earthquake from Satellite Images. Bull. Seismol. Soc. Am. 94, 2407–2413 (2004).
Mandal, P. et al. Characterization of the causative fault system for the 2001 Bhuj earthquake of Mw 7.7. Tectonophysics 378, 105–121 (2004).
Mandal, P. Estimation of static stress changes after the 2001 Bhuj earthquake: Implications towards the northward spatial migration of the seismic activity in Kachchh, Gujarat. J. Geol. Soc. India 74, 487–497 (2009).
Schmidt, D. A. & Bürgmann, R. InSAR constraints on the source parameters of the 2001 Bhuj earthquake. Geophys. Res. Lett. 33, 2005GL025109 (2006).
Chandrasekhar, D. V., Bürgmann, R., Reddy, C. D., Sunil, P. S. & Schmidt, D. A. Weak mantle in NW India probed by geodetic measurements following the 2001 Bhuj earthquake. Earth Planet. Sci. Lett. 280, 229–235 (2009).
Copley, A., Avouac, J.-P., Hollingsworth, J. & Leprince, S. The 2001 Mw 7.6 Bhuj earthquake, low fault friction, and the crustal support of plate driving forces in India. J. Geophys. Res. 116, B08405 (2011).
Wang, T., Wei, S. & Jónsson, S. Coseismic displacements from SAR image offsets between different satellite sensors: Application to the 2001 Bhuj (India) earthquake. Geophys. Res. Lett. 42, 7022–7030 (2015).
Srivastava, E., Parrino, N., Malik, J., Pepe, F. & Burrato, P. Looking for the Hidden Morphological Signature of Active Faults in a Low Strain Rate Region: Clues from the Eastern Kachchh Region (NW India). https://meetingorganizer.copernicus.org/EGU21/EGU21-15982.html (2021) https://doi.org/10.5194/egusphere-egu21-15982.
J. P. McCalpin & M. G. Thakkar. 2001 Bhuj-Kachchh earthquake: Surface faulting and its relation with neotectonics and regional structures, Gujarat, Western India. Ann. Geophys. 46, (2009).
Wesnousky, S. G. et al. Eight days in Bhuj: Field Report bearing on surface rupture and genesis of the 26 January 2001 earthquake in India. Seismol. Res. Lett. 72, 514–524 (2001).
Nakata, T. et al. Extensive surface deformation around Budharmora associated with the January 26, 2001 Republic Day (Bhuj) earthquake of India. Active Fault Res. 2001, 127–136 (2001).
Mathew, G., Singhvi, A. K. & Karanth, R. V. Luminescence chronometry and geomorphic evidence of active fold growth along the Kachchh Mainland Fault (KMF), Kachchh, India: Seismotectonic implications. Tectonophysics 422, 71–87 (2006).
Malik, J. N. et al. January 26, 2001, the Republic Day (Bhuj) earthquake of Kachchh and active faults, Gujarat, western India. Active Fault Res. 2001, 112–126 (2001).
Malik, J. N., Mornio, M., Mishra, P., Bhuiyan, C. & Kaneko, F. First active fault exposure identified along Kachchh mainland fault: Evidence from trench excavation near Lodai Village, Gujarat, Western India. Geol. Soc. India 71, 201–208 (2008).
Malik, J. N., Naik, S. P., Sahoo, S., Okumura, K. & Mohanty, A. Paleoseismic evidence of the CE 1505 (?) and CE 1803 earthquakes from the foothill zone of the Kumaon Himalaya along the Himalayan Frontal Thrust (HFT), India. Tectonophysics 714–715, 133–145 (2017).
Morino, M. et al. Active low-angle reverse fault and wide quaternary deformation identified in jhura trench across the Kachchh Mainland Fault, Kachchh, Gujarat, India. (2008) Active Fault Research 2008, 71–78 (2008)..
Morino, M., Malik, J. N., Mishra, P., Bhuiyan, C. & Kaneko, F. Active fault traces along Bhuj Fault and Katrol Hill Fault, and trenching survey at Wandhay, Kachchh, Gujarat, India. J. Earth Syst. Sci. 117, 181–188 (2008).
Rajendran, C. P., Rajendran, K., Thakkar, M. & Goyal, B. Assessing the previous activity at the source zone of the 2001 Bhuj earthquake based on the near-source and distant paleoseismological indicators. J. Geophys. Res. Solid Earth 113, 2006JB004845 (2008).
Kothyari, G. C. et al. Palaeoseismic investigations along the Kachchh Mainland Fault: A comprehensive review and new insights of the past earthquakes in the Kachchh basin, western India. Quat. Int. 599–600, 184–209 (2021).
Malik, J. N., Gadhavi, M. S., Kothyari, G. C. & Satuluri, S. Paleo-earthquake signatures from the South Wagad Fault (SWF), Wagad Island, Kachchh, Gujarat, western India: A potential seismic hazard. J. Struct. Geol. 95, 142–159 (2017).
Teran, O. J. et al. Geologic and structural controls on rupture zone fabric: A field-based study of the 2010 Mw 7.2 El Mayor-Cucapah earthquake surface rupture. Geosphere 11, 899–920 (2015).
Livio, F. A., Ferrario, M. F., Frigerio, C., Zerboni, A. & Michetti, A. M. Variable fault tip propagation rates affected by near-surface lithology and implications for fault displacement hazard assessment. J. Struct. Geol. 130, 103914 (2020).
Toutin, T. DSM generation and evaluation from QuickBird stereo imagery with 3D physical modelling. Int. J. Remote Sens. 25, 5181–5192 (2004).
Gianinetto, M. & Fassi, F. Validation of Cartosat-1 DTM generation for the salon de provence test site (2008).
Biswas, S. K. Regional tectonic framework, structure and evolution of the western marginal basins of India. Tectonophysics 135, 307–327 (1987).
Biswas, S. K. & Deshpande, S. V. Geological and tectonic maps of Kutch. Bull. Oil Nat. Gas Commun. 7, 115–116 (1970).
Biswas, S. K. A review of structure and tectonics of Kutch basin, western India, with special reference to earthquakes. Curr. Sci. 88 (2005).
Karanth, R. V. & Gadhavi, M. S. Structural intricacies: Emergent thrusts and blind thrusts of Central Kachchh, western India. Curr. Sci. 93 (2007).
Srivastava, E. et al. Extremely fast Holocene coastal landscape evolution in the Kachchh Upland (NW India): Clues from a multidisciplinary review. J. Maps https://doi.org/10.1080/17445647.2023.2167617 (2023).
Gahalaut, V. K., Gahalaut, K., Dumka, R. K., Chaudhury, P. & Yadav, R. K. Geodetic evidence of high compression across seismically active Kachchh Paleorift, India. Tectonics 38, 3097–3107 (2019).
Heidbach, O. et al. The World Stress Map database release 2016: Crustal stress pattern across scales. Tectonophysics 744, 484–498 (2018).
Quittmeyer, R. C. & Jacob, K. H. Historical and modern seismicity of Pakistan, Afghanistan, northwestern India, and southeastern Iran. Bull. Seismol. Soc. Am. 69, 773–823 (1979).
Bilham, R. et al. Seismic hazard in Karachi, Pakistan: Uncertain past. Uncertain Future. Seismol. Res. Lett. 78, 601–613 (2007).
Chung, W.-Y. & Gao, H. Source parameters of the Anjar earthquake of July 21, 1956, India, and its seismotectonic implications for the Kutch rift basin. Tectonophysics 242, 281–292 (1995).
Rastogi, B. K., Mandal, P., Biswas, S. K. & Talwani, P. Seismogenesis of earthquakes occurring in the ancient rift basin of Kachchh, Western India. Intraplate Earthq. 126–161 (2014).
Lakhote, A. et al. Estimation of active surface deformation in the eastern Kachchh region, western India: Application of multi-sensor DInSAR technique. Quat. Int. 575–576, 130–140 (2021).
Malik, J. N., Sohoni, P. S., Merh, S. S. & Karanth, R. V. Active tectonic control on alluvial fan architecture along Kachchh mainland Hill Range, Western India. Z. Für Geomorphol. 45, 81–100 (2001).
Parrino, N. et al. Plio-Quaternary coastal landscape evolution of north-western Sicily (Italy). J. Maps 19, 2159889 (2023).
Parrino, N. et al. Elusive active faults in a low strain rate region (Sicily, Italy): Hints from a multidisciplinary land-to-sea approach. Tectonophysics 839, 229520 (2022).
Pirrotta, C., Parrino, N., Pepe, F., Tansi, C. & Monaco, C. Geomorphological and morphometric analyses of the catanzaro trough (Central Calabrian Arc, Southern Italy): Seismotectonic implications. Geosciences 12, 324 (2022).
Heidbach, O. WSM quality ranking scheme, database description and analysis guidelines for stress indicator. WSM Technical Report 16-01, GFZ German Research Centre for Geosciences (2016).
Evans, G. A., Ramachandran, B., Zhang, Z., Bailey, G. B. & Cheng, P. An accuracy assessment of cartosat-1 stereo image data-derived digital elevation models: A case study of the drum Mountains, Utah. Int. Arch. Photogramm. Remote Sens. Spatial Inf. Sci. 37(B1), 1161–1164 (2008).
Jacob, R. W. & Urban, T. M. Ground-penetrating radar velocity determination and precision estimates using common-midpoint (CMP) collection with hand-picking, semblance analysis and cross-correlation analysis: A case study and tutorial for archaeologists: GPR velocity determination and precision estimates. Archaeometry 58, 987–1002 (2016).
Snyder, S. L. & Duval, J. S. Design and Construction of a Gamma-Ray Spectrometer System for Determining Natural Radioelement Concentrations in Geological Samples at the US Geological Survey in Reston, Virginia. https://pubs.er.usgs.gov/publication/ofr0329 (2003).
DuRoss, C. B. et al. Variable normal-fault rupture behavior, northern Lost River fault zone, Idaho, USA. Geosphere 15, 1869–1892 (2019).
Schwanghart, W. & Scherler, D. Short Communication: TopoToolbox 2—MATLAB-based software for topographic analysis and modeling in Earth surface sciences. Earth Surf. Dyn. 2, 1–7 (2014).
Mejdahl, V. & Christiansen, H. H. Procedures used for luminescence dating of sediments. Quat. Sci. Rev. 13, 403–406 (1994).
Murray, A. S. & Wintle, A. G. Luminescence dating of quartz using an improved single-aliquot regenerative-dose protocol. Radiat. Meas. 32, 57–73 (2000).
Thompson, J. A. et al. Coarse- versus fine-grain quartz OSL and cosmogenic 10 Be dating of deformed fluvial terraces on the northeast Pamir margin, northwest China. Quat. Geochronol. 46, 1–15 (2018).
Murray, A. S. & Wintle, A. G. The single aliquot regenerative dose protocol: Potential for improvements in reliability. Radiat. Meas. 37, 377–381 (2003).
Prescott, J. R. & Hutton, J. T. Environmental dose rates and radioactive disequilibrium from some Australian luminescence dating sites. Quat. Sci. Rev. 14, 439–448 (1995).
Allmendinger, R. W. Inverse and forward numerical modeling of trishear fault-propagation folds. Tectonics 17, 640–656 (1998).
Zehnder, A. T. & Allmendinger, R. W. Velocity field for the trishear model. J. Struct. Geol. 22, 1009–1014 (2000).
Wells, D. L. & Coppersmith, K. J. New empirical relationships among magnitude, rupture length, rupture width, rupture area, and surface displacement. Bull. Seismol. Soc. Am. 84, 974–1002 (1994).
Leonard, M. Self-consistent earthquake fault-scaling relations: Update and extension to stable continental strike-slip faults. Bull. Seismol. Soc. Am. 104, 2953–2965 (2014).
Wesnousky, S. G. Displacement and geometrical characteristics of earthquake surface ruptures: Issues and implications for seismic-hazard analysis and the process of earthquake rupture. Bull. Seismol. Soc. Am. 98, 1609–1632 (2008).
Zhang, Y. et al. Reconciling patterns of long-term topographic growth with coseismic uplift by synchronous duplex thrusting. Nat. Commun. 14, 8073 (2023).
Joshi, J. P. & Bisht, R. S. India and the Indus Civilization. VC National Museum Institute (1994).
Tuttle, M. P., Collier, J., Wolf, L. W. & Lafferty, R. H. III. New evidence for a large earthquake in the New Madrid seismic zone between AD 1400 and 1670. Geology 27, 771–774 (1999).
Meghraoui, M., Camelbeeck, T., Vanneste, K., Brondeel, M. & Jongmans, D. Active faulting and paleoseismology along the Bree fault, lower Rhine graben, Belgium. J. Geophys. Res. Solid Earth 105, 13809–13841 (2000).
Prentice, C. S. et al. Prehistoric ruptures of the Gurvan Bulag fault, Gobi Altay, Mongolia. J. Geophys. Res. Solid Earth 107, ESE1-1-ESE1-18 (2002).
Crone, A. J. Paleoseismicity of two historically quiescent faults in Australia: Implications for fault behavior in stable continental regions. Bull. Seismol. Soc. Am. 93, 1913–1934 (2003).
Štěpančíková, P. et al. Active tectonics research using trenching technique on the south-eastern section of the Sudetic Marginal Fault (NE Bohemian Massif, central Europe). Tectonophysics 485, 269–282 (2010).
Štěpančíková, P. et al. Active tectonics in the Cheb Basin: Youngest documented Holocene surface faulting in Central Europe?. Geomorphology 327, 472–488 (2019).
Campbell, G. E. et al. Great earthquakes in low strain rate continental interiors: An example from SE Kazakhstan. J. Geophys. Res. Solid Earth 120, 5507–5534 (2015).
Abdrakhmatov, K. E. et al. Multisegment rupture in the 11 July 1889 Chilik earthquake (Mw 8.0–8.3), Kazakh Tien Shan, interpreted from remote sensing, field survey, and paleoseismic trenching. J. Geophys. Res. Solid Earth 121, 4615–4640 (2016).
Grützner, C. et al. Assessing the activity of faults in continental interiors: Palaeoseismic insights from SE Kazakhstan. Earth Planet. Sci. Lett. 459, 93–104 (2017).
Grützner, C. et al. Holocene surface-rupturing earthquakes on the Dinaric Fault System, western Slovenia. Solid Earth 12, 2211–2234 (2021).
Špaček, P. et al. Fault slip versus slope deformations: Experience from paleoseismic trenches in the region with low slip-rate faults and strong Pleistocene periglacial mass wasting (Bohemian Massif). Quat. Int. 451, 56–73 (2017).
King, T. R. et al. Paleoseismology of the 2016 M W 6.1 Petermann earthquake source: Implications for intraplate earthquake behaviour and the geomorphic longevity of bedrock fault scarps in a low strain-rate cratonic region. Earth Surf. Process. Landf. 46, 1238–1256 (2021).
Pena-Castellnou, S. et al. Surface rupturing earthquakes along the eastern Rhine Graben Boundary Fault near Ettlingen-Oberweier (Germany). Tectonophysics 869, 230114 (2023).
Acknowledgements
Funding received from the Ministry of Earth Sciences (MoES), New Delhi [Grant Nos. MoES/PO(Seismo)/1(270)/AFM/2015 & MoES/PO(Geo)/240-A/2020] to JNM and MSG is duly acknowledged. We are grateful to both the reviewers for their constructive comments and suggestion, which helped us improving our manuscript.
Author information
Authors and Affiliations
Contributions
J.N.M. looked at the overall aspect of the research work and led all the field visits to Kachchh. M.S.G. was involved in all fieldwork activities, supervising the analysis and interpretation of trenches and deducing paleoseismic events. E.S. participated in two fieldwork expeditions, contributed to generating figures, and collaborated with N.S. and S.A. at IIT Kanpur on sediments' Optically Stimulated Luminescence (OSL) dating. F.L. contributed towards trishear kinematic modelling. N.P. P.B. and A.S. aided and supervised in analyzing and interpreting the datasets. All authors contributed to their respective work assigned in preparing the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Malik, J.N., Srivastava, E., Gadhavi, M.S. et al. Holocene surface-rupturing paleo-earthquakes along the Kachchh Mainland Fault: shaping the seismic landscape of Kachchh, Western India. Sci Rep 14, 11612 (2024). https://doi.org/10.1038/s41598-024-62086-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-024-62086-z
- Springer Nature Limited