Highlights
-
Ti3C2Tx MXene-based coaxial zinc-ion hybrid fiber supercapacitors (FSCs) were fabricated with braided structure, which can be prepared continuously and present excellent flexibility and ultrastability.
-
A sports watch driven by the watch belts which weaved uses the obtained zinc-ion hybrid FSC and LED arrays lighted by the FSCs under embedding into textiles, demonstrating the great potential application in smart wearable textiles.
Abstract
Zinc-ion hybrid fiber supercapacitors (FSCs) are promising energy storages for wearable electronics owing to their high energy density, good flexibility, and weavability. However, it is still a critical challenge to optimize the structure of the designed FSC to improve energy density and realize the continuous fabrication of super-long FSCs. Herein, we propose a braided coaxial zinc-ion hybrid FSC with several meters of Ti3C2Tx MXene cathode as core electrodes, and shell zinc fiber anode was braided on the surface of the Ti3C2Tx MXene fibers across the solid electrolytes. According to the simulated results using ANSYS Maxwell software, the braided structures revealed a higher capacitance compared to the spring-like structures. The resulting FSCs exhibited a high areal capacitance of 214 mF cm–2, the energy density of 42.8 μWh cm−2 at 5 mV s−1, and excellent cycling stability with 83.58% capacity retention after 5000 cycles. The coaxial FSC was tied several kinds of knots, proving a shape-controllable fiber energy storage. Furthermore, the knitted FSC showed superior stability and weavability, which can be woven into watch belts or embedded into textiles to power smart watches and LED arrays for a few days.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Fiber electronics is a newly emerged flexible device developed in recent years, which offers unique ultra-flexible, shape adaptable, and weavability properties, allowing various deformations include bending, stretching, twisting, etc. [1, 2]. Up to date, different kinds of fiber devices such as fiber generators, sensors, detectors have been reported [3,4,5]. These fiber devices have increasingly seeking for the matched fiber energy storage to realize the stable, independent, and complete application circle [6]. The typical design of the fiber energy storage consists of fiber Li-ion battery, supercapacitors (SCs), hybrid supercapacitors [7]. Fiber hybrid supercapacitor (FSC) that employs metal-ion as anode with high capacitance, ultra-long serving time, and robust security is well developed due to its wide applications in wearable electronics, smart clothes, and multi-functional integrated textiles [8]. It is found the structures of the FSC have a profound influence on electrochemical behaviors. For example, Peng’s group reported the specific capacitance of coaxial SCs exhibited approximately tenfold higher than that of twisted ones [9]. Therefore, the FSC with novel coaxial structures needs further to be developed to meet the practical demands of fiber electronic devices. As an important branch of the hybrid FSC, zinc-ion-based FSCs that possess superior characteristics, such as high theoretical capacity (820 mAh g−1 and 5855 mAh cm−3), high safety, nontoxicity, low cost, abundant resources (about 300 times higher than lithium), and lightweight, are considered as an ideal energy supply unit [10]. Although research on the Zn-ion hybrid SCs has been expanding rapidly, the Zn-ion-based FSC is relatively seldom explored.
Carbides and nitrides (MXenes) with two-dimensional (2D) structures have been demonstrated as promising cathode materials for the fabrication of Zn-ion hybrid SC due to their high electrical conductivity (up to 20,000 S cm−1) and excellent specific capacitance (up to 1500 F cm−3) [11,12,13,14]. Moreover, different from traditional hydrophobic carbon materials like graphene, carbon nanotube, MXenes contain abundant surface functional groups offer hydrophilic properties, which are suitable for solution processing and fiber device fabrication by spray coating, printing, and coating, etc. [15,16,17,18,19,20,21,22,23,24]. Unfortunately, the Ti3C2Tx Mxene-based Zn-ion FSC has rarely been reported in the previous literature; the reason and difficulty in the fabrication of Zn//Ti3C2Tx MXene FSC are summarized in the following three points. 1) The preparation of the super-long electrodes, ensuring continuous fabrication of FSC. 2) The optimization of the structures of the FSC for enhancing the electrochemical performance of the assembled devices. 3) The selection of the solid-state electrolyte, which endows the FSC with stable and wearable properties. To solve the problems mentioned above, first of all, the dynamic dipping and electrodeposition equipment for preparing super-long Ti3C2Tx fiber cathode and Zn anode need to be designed [25]. Secondly, FSC is usually divided into two main types, including twisted and coaxial structures [26,27,28]. The coaxial structure has been demonstrated better performances compared to twisted. Coaxial FSCs can be further broken up into two forms consisting of braided and winded. Braided shell electrodes with parallel crossed network structures have smaller resistance, easier to collect and transfer charge, which is expected a better performance. Moreover, the braided coaxial FSCs can weave fibers into continuous tubular structures, realizing a continuous super-long fabrication of the coaxial FSC [29, 30]. Finally, the novel all-solid-state electrolyte needs to be synthesized.
Taking all these into account, we provide a facile approach to fabricate a superlong coaxial FSC with Ti3C2Tx MXene fibers core cathode and Zinc fibers shell anode, which was braided into the tubular structure and wrapped around the cathode. The fabricated coaxial FSC showed high areal capacitance (up to 214 mF cm−2), energy density (42.8 μWh cm−2) at 5 mV s−1, and excellent cycling stability of 83.58% capacity retention after 5000 cycles. Moreover, the simulated results using ANSYS Maxwell software also exhibited higher capacitance of braided coaxial FSC. In order to prove the weavability and high energy density, the coaxial FSC was woven into textiles and used to power LED lights and smart watches.
2 Experimental Section
2.1 Materials
Silver-plated nylon fibers were purchased from Qingdao Tianyin Textile Technology Co., Ltd. Ti3AlC2 was purchased from Carbon-Ukraine. Lithium fluoride (LiF), hydrochloric acid (HCl), zinc oxide (ZnO), sodium hydroxide (NaOH), zinc sulfate monohydrate (ZnSO4·H2O), gelatin were obtained from Shanghai Aladdin Biochemical Technology Co., Ltd. Cellulose diaphragm was provided by Tianjin Annuohe New Energy Technology Co., Ltd.
2.2 Preparation of 2D Delaminated Ti3C2Tx MXene
Ti3C2Tx MXene nanoplates were prepared according to the previously reported selective etching route. Typically, 1 g of Ti3AlC2 powder was slowly added into the mixture solution of 1 g LiF and 20 mL HCl (9 M) and then magnetically stirred at 35 ℃ for 24 h. The resulting suspension was washed with deionized (DI) water and centrifuged several times until the pH value of the solution reached neutral to obtain multi-layer Ti3C2Tx MXene. Subsequently, the solution was sonicated in the ice bath for 1 h. Finally, the Ti3C2Tx solution was collected by centrifuging at 3500 rpm for 5 min, while small-sized Ti3C2Tx MXene was obtained.
2.3 Preparation of Solid-state Electrolyte
Solid-state electrolyte was prepared by adding appropriate 4.5 g gelatin into 30 mL ZnSO4 (1.5 M); then, the solution was magnetically stirred at 60 ℃ for 30 min to obtain a clear solution. Finally, the solution was naturally cooled and solidified at room temperature.
3 Results and Discussion
3.1 Material Characterizations
Figure 1a shows the continuous fiber manufacturing process to assemble Zn-/MXene-based braided coaxial FSC. The homemade semi-automatic equipment was employed to prepare Ti3C2Tx cathode by the dynamic multiple dipping fiber into MXene suspension. The concentration of the Ti3C2Tx suspension was about 10 mg mL−1. After drying the Ti3C2Tx fiber cathode, the mass loading of 0.15 mg cm−1 for the Ti3C2Tx cathode was obtained. The length of the prepared Ti3C2Tx MXene fiber cathode reached up to 1.5 m, as shown in Fig. S1a. The Zn fiber anode (Fig. S1b) was made by the continuous electrodeposition method. The corresponding homemade electrodeposition equipment is displayed in Fig. S1c. In a typical three-electrode electrochemical workstation system, two pieces of Zinc plate paralleled with the fiber served as work electrode and Hg/HgO worked as the reference electrode; the pre-washed silver-plated fibers (100 D 36 f) were connected to the counterelectrode and went through the electrolyte that contains a mixture of 0.1 M zinc oxide (ZnO) and 3.75 M sodium hydroxide (NaOH) at a different speed. The length of the silver-plated fibers immersion in the electrolyte is 12 cm. The constant current used in the electrodeposition process was tuned from 6 to 9 mA. After the electrodeposition process, the Zn coated fiber was immediately washed in DI water and dried at 40 ℃ to prevent oxidation. The SEM images of the Zn fiber anode at different currents and move speeds are provided in Fig. S4. From the SEM images, it is found the Zn on the surface of the fiber exhibited uniform formation and a suitable amount when the moving speed of the fiber was 2 cm min−1 at the constant current of 7 mA. Next, a cellulose diaphragm of 35 μm thick was winded on the surface of the Ti3C2Tx MXene-coated fiber. Zinc-coated fiber anodes were then woven into a network layer of tubular fabric with plain texture on the surface of the cellulose diaphragm by a 2D knitting machine. Six yarns were woven clockwise and the other six anticlockwise around the MXene cathode, intersecting in pairs to form the outer layer of three-layer coaxial FSC. Finally, the solid electrolyte made of 1.5 M ZnSO4 and 15.0 W/V % of gelatin was added. The braided FSC was fully immersed in a gelatin electrolyte and kept at 50 ℃ for 10 min to prepare a fully solid-state FSC. The SEM image of the fabricated coaxial FSC is presented in Fig. 1b. The braided structure of the Zn anode can be clearly seen. Figure 1c depicts the mapping images of the coaxial FSC structure, which proves that zinc elements are evenly distributed throughout the surface of the fibers. Figure S2 depicts the SEM and mapping images of the Ti3C2Tx MXene cathode. The cross-sectional SEM image of the coaxial FSC (Fig. 1d) shows that the FSC consists of shell-like Zn anode, cellulose membrane, and the core Ti3C2Tx MXene cathode, providing a separated, uniform, stable, and continuous structure.
3.2 Comparison of Braided and Winded Coaxial FSCs
To verify the better electrochemical performance of the coaxial FSC with braided structures, the contrast winded coaxial FSC was also fabricated, as shown in Fig. 2a, b. The serried spring-like Zn cathode can be noticed in the SEM images (Fig. 2b). Figure 2c demonstrates that braided FSCs delivered higher specific areal capacitances of 214 mF cm−2, which is almost twice that of winded FSCs at scan rates of 5 mV s−1. To uncover the reason for the better performance of the braided FSC, the potential and energy distributions simulated by the ANSYS Maxwell analysis software of the two kinds of FSCs were presented. The corresponding parameters are provided (Table S1). Figure 2d, g exhibits the 3D models of braided and winded coaxial FSCs according to the simulating parameters, respectively. Next, the material properties of the models and electrolyte parameters were defined in ANSYS Maxwell analysis software; a voltage of − 0.6 to 0.6 V was added between the two electrodes. Finally, solution settings were added to the analysis voltage field and energy field for simulation analysis.
Figure 2e, h depicts the potential distributions between anode and cathode when a voltage ranging from − 0.6 to 0.6 V was applied to the devices, respectively. The negative and positive voltage used in the analysis process was potential difference related to the electroneutral electrolyte. In addition, large span voltage could provide more clearly charge distribution images. Compared with winded FSCs, braided coaxial FSCs possess a much more uniform potential distribution and higher electric charge-transfer effect in the axis direction since the external fibers of braided coaxial FSC have a parallel form leading to faster charge collection and transfer rates, while in winded coaxial FSC, the charge transfer within a prolonged path increases the resistance, which is not beneficial for the electrochemical performance. Figure 2f, i presents the energy distributions in both structural FSCs. From the distribution images, we can see the braided devices have four electrode branches knitted in parallel, providing an increased energy density. Such a braided structure also maintains the charge transfer function in case of one or two fiber electrodes is cut or broken. In contrast, the winded one with a single shell electrode is disrupted when anywhere from the shell electrode is victimized, disabling the charge storage and transfer functions. The theoretical specific capacitance was calculated according to the corresponding calculation formula [30]. A capacitance ratio of 1.53:1 was obtained, which is consistent with the experimental results, confirming and explaining the better electrochemical performances of the braided coaxial FSC.
3.3 Electrochemical Performance Analysis
The electrochemical properties of the braided coaxial Zn//Ti3C2Tx FSC with the length of 2 cm were systematically gathered, as shown in Fig. 3. Figure 3a displays the CV curves of the braided coaxial FSC in a voltage window of 1.2 V at scan rates ranging from 5 to 200 mV s−1, respectively. Obvious redox peaks at the lower potential range can be observed, which are caused by the insertion of Zn ion into the Ti3C2Tx layers, revealing the combined energy storage mechanism of pseudoredox reaction and double-layer effect. In detail, when charging the Zn//Ti3C2Tx fiber devices, Zn transforms to Zn2+ and moves from anode to cathode, then intercalates into the Ti3C2Tx layers, or adsorbs on the surface of the Ti3C2Tx cathode. When the device charges, the procedure is the inverse of the above process. With the increase in scanning rate, the shape of the CV curves was unchanged, indicating that the coaxial FSC has a remarkable rate capability and excellent capacitive behavior. Figure 3b shows the calculated specific area capacitances of 214.00 to 101.15 mF cm−2 at increasing scanning rates from 5 to 100 mV s−1, with the coulombic efficiency of 100%, respectively. Almost 50% capacitance remained as the scan rate increased 20 times, demonstrating the superior rate stability of the fabricated devices. Figure 3c shows the areal capacitance with respect to cycle number at different current densities. It can be seen the 96.75% of the initial capacitance remained after 1600 cycles. The galvanostatic charge–discharge (GCD) curves of the designed FSC (Fig. 3d) with a stable voltage window of 0–1.2 V show the symmetric triangular shapes at higher current densities (> 5 mA cm−1) and slight deviation at current density of 1 mA cm−2, revealing the capacitive and pseudoredox reaction charge storage behavior. Electrochemical impedance spectroscopy (EIS) was conducted to understand the charge transfer and ion transport properties of the coaxial FSC. As shown in Fig. 3e, the Nyquist curve obtained in frequencies ranging from 100 kHz to 0.01 Hz confirmed the low charge transport resistance of 4.41 Ω. Figure 3f displays the compared energy and power densities of this FSC device and reported works; the highest energy density of 42.8 μWh cm−2 at a power density of 0.64 mW cm−2 of our devices can be calculated, which is much higher than that of recently reported works as shown in Table 1 [31,32,33,34,35,36,37,38,39,40]. Figure 3g exhibits the capacity retention of the braided coaxial FSC after 5000 charge/discharge cycles at a current density of 20 mA cm−2; 83.6% of initial value was remained with high Coulombic efficiency of about 100%, suggesting the outstanding cycling stabilities of the fabricated Zn//Ti3C2Tx FSC.
3.4 Flexibility of Fabricated FSC
The flexibility and weavability of the fabricated Zn//Ti3C2Tx FSC were then measured. The CV curves of the coaxial FSC bent with different curvature diameters are compared in Fig. 4a. The shapes of the CV curves are maintained, showing that the FSC has excellent flexibility, which is vital for wearable energy storage devices. In order to demonstrate the superior stability of coaxial FSC, two FSCs with a length of 3 cm were connected in series to power an electronic clock, as shown in Fig. 4b. Coaxial FSCs can normally and stably power the electronic timepiece under knotting and bending, and the power supply duration was able to reach 110 min (Fig. S5). Moreover, 12 red LED lights could be lighted by 3 FSCs connected in series. It is worth noting that the 3 FSCs were easily knitted in a textile (Fig. 4c). The coaxial FSC may twisted during the weaving process and practical application, so we also tested the twisted performance of coaxial FSC. The capacitance of the coaxial FSC with one end fixed and the other end rotated at different angles was measured, as shown in Fig. 4d. The capacitance is maintained 95% of the original value when the FSC rotated by 180 degrees, proving the good flexibility of the devices.
3.5 Application of Coaxial FSCs
To widen the potential windows and improve the energy density of the coaxial Zn//Ti3C2Tx FSCs, two coaxial FSCs assembled in series and parallel were designed, respectively, as shown in Fig. 5a. The CV curves at the same scan rate showed the double voltage window and current when two coaxial FSCs connected in series and parallel, demonstrating the output voltage and capacitance can be adjusted easily by connecting multiple coaxial FSCs in series and parallel; thus, the fabricated FSCs could meet the energy and power requirements of energy storage devices in practical applications. The capacitance and energy of coaxial FSCs also increased proportionally with the increase in device lengths (Fig. 5b), so it is essential to realize the continuous fabrication of the FSC in practical application. From Fig. 5c, it can be seen that a length of 1.5 m coaxial FSC could be assembled at the same time because of the successful preparation of the meters of Zn fiber anode and Ti3C2Tx cathode. The softness of the coaxial FSC makes it possible to weave a fabric, so we wove a wristband by employing two coaxial FSCs, which were then used to power a sports watch. Furthermore, six coaxial FSCs were embedded into a glove to drive an LED array, and a smart bracelet could be charged by the plain fabric woven using coaxial FSCs.
4 Conclusions
The high-performance Zn-ion FSC was obtained by designing the braided coaxial structures and utilization of Ti3C2Tx MXene cathode, which exhibited a high areal capacitance of 214 mF cm−2 and energy density of 42.8 μWh cm−2 at 5 mV s−1. Moreover, the FSC showed excellent cycling stability and good capacitance retention at bending, kitting, and braiding states. The letters “CAS” composed of 44 LED arrays could be lighted by six FSCs woven into textiles. This work represents a step toward the mass production of wearable energy storage devices and the potential for use in practical applications.
References
L. Ma, R. Wu, A. Patil, S. Zhu, Z. Meng et al., Full-textile wireless flexible humidity sensor for human physiological monitoring. Adv. Funct. Mater. 29, 1904549 (2019). https://doi.org/10.1002/adfm.201904549
J. Xiong, J. Chen, P. Lee, Functional fibers and fabrics for soft robotics, wearables, and human robot interface. Adv. Mater. (2020). https://doi.org/10.1002/adma.202002640
J. An, Y. Ma, M. He, J. Yan, C. Zhang et al., A wearable and highly sensitive textile-based pressure sensor with Ti3C2Tx nanosheets. Sensor Actuat. A-Phys. 311, 112081 (2020). https://doi.org/10.1016/j.sna.2020.112081
J. Shirley, S. Florence, B. Sreeja, G. Padmalaya, S. Radha, Zinc oxide nanostructure-based textile pressure sensor for wearable applications. J. Mater. Sci. Mater. El. 31, 16519–16530 (2020). https://doi.org/10.1007/s10854-020-04206-9
G. Fang, J. Zhou, A. Pan, S. Liang, Recent advances in aqueous zinc-ion batteries. ACS Energy Lett. 10, 2480–2501 (2018). https://doi.org/10.1021/acsenergylett.8b01426
H. Li, L. Ma, C. Han, Z. Wang, Z. Liu et al., Advanced rechargeable zinc-based batteries: recent progress and future perspectives. Nano Energy 62, 550–587 (2019). https://doi.org/10.1016/j.nanoen.2019.05.059
L. Li, D. Chen, G.Z. Shen, All-Ti3C2TxMXene based flexible on-chip microsupercapacitor array. Chem. Res. Chinese Univ. 36, 694–698 (2020). https://doi.org/10.1007/s40242-020-0197-9
L. Dong, X. Ma, Y. Li, L. Zhao, W. Liu et al., Extremely safe, high-rate and ultralong-life zin cion hybrid supercapacitors. Energy Storage Mater. 13, 96–102 (2018). https://doi.org/10.1016/j.ensm.2018.01.003
X. Chen, L. Qiu, J. Ren, G. Guan, H. Lin et al., Novel electric double-layer capacitor with a coaxial fiber structure. Adv. Mater. 25, 6436 (2013). https://doi.org/10.1002/adma.201301519
H. Wang, M. Wang, Y. Tang, A novel zinc-ion hybrid supercapacitor for long-life and low-cost energy storage applications. Energy Storage Mater. 13, 1–7 (2018). https://doi.org/10.1016/j.ensm.2017.12.022
S. Seyedin, S. Uzun, A. Levitt, B. Anasori, G. Dion et al., MXene composite and coaxial fibers with high stretchability and conductivity for wearable strain sensing textiles. Adv. Funct. Mater. 30, 1910504 (2020). https://doi.org/10.1002/adfm.201910504
L. Li, W. Liu, K. Jiang, D. Chen, F. Qu et al., In-situ annealed Ti3C2Tx MXene based all-solid-state flexible zn-ion hybrid micro supercapacitor array with enhanced stability. Nano-Micro Lett. 13, 100 (2021). https://doi.org/10.1007/s40820-021-00634-2
J. Zhang, S. Seyedin, Z. Gu, W. Yang, X. Wang, MXene: a potential candidate for yarn supercapacitors. Nanoscale 9, 18604–18608 (2017). https://doi.org/10.1039/c7nr06619h
S. Seyedin, E. Yanza, J. Razal, Knittable energy storing fiber with high volumetric performance made from predominantly MXene nanosheets. J. Mater. Chem. A 5, 24076–24082 (2017). https://doi.org/10.1039/c7ta08355f
S. Uzun, S. Seyedin, A. Stoltzfus, A. Levitt, M. Alhabeb et al., Knittable and washable multifunctional MXene-coated cellulose yarns. Adv. Funct. Mater. 29, 1905015 (2019). https://doi.org/10.1002/adfm.201905015
M. Alhabeb, K. Maleski, B. Anasori, P. Lelyukh, L. Clark et al., Guidelines for synthesis and processing of two-dimensional titanium carbide (Ti3C2Tx MXene). Chem. Mater. 29, 7633–7644 (2017). https://doi.org/10.1021/acs.chemmater.7b02847
M. Lukatskaya, O. Mashtalir, C. Ren, Y. Dall’ Agnese, P. Rozier et al., Cation intercalation and high volumetric capacitance of two dimensional titanium carbide. Science. 341, 1502 (2013). https://doi.org/10.1126/science.1241488
Z. Ling, C. Ren, M. Zhao, J. Yang, J. Giammarco et al., Flexible and conductive MXene films and nanocomposites with high capacitance. Proc. Natl. Acad. Sci. USA 111, 16676–16681 (2014). https://doi.org/10.1073/pnas.1414215111
M. Levi, M. Lukatskaya, S. Sigalov, M. Beidaghi, N. Shpigel et al., Solving the capacitive paradox of 2D MXene using electrochemical quartz-crystal admittance and in situ electronic conductance measurements. Adv. Energy Mater. 5, 1400815 (2015). https://doi.org/10.1002/aenm.201400815
M. Lukatskaya, S. Bak, X. Yu, X. Yang, M. Barsoum et al., Probing the meshanism of high capacitance in 2D titanium carbide using in situ X-ray absorption spectroscopy. Adv. Energy Mater. 5, 1500589 (2015). https://doi.org/10.1002/aenm.201500589
N. Wang, J. Liu, Y. Zhao, M. Hu, R. Qin et al., Laser-cutting fabrication of mxene-based flexible micro-supercapacitors with high areal capacitance. ChemNanoMat 5, 658–665 (2019). https://doi.org/10.1002/cnma.201800674
H. Lv, Q. Pan, Y. Song, X. Liu, T. Liu, A review on nano-/microstructured materials constructed by electrochemical technologies for supercapacitors. Nano-Micro Lett. 12, 118 (2020). https://doi.org/10.1007/s40820-020-00451-z
C. Li, X. Zhang, K. Wang, F. Su, C. Chen et al., Recent advances in carbon nanostructures prepared from carbon dioxide for high-performance supercapacitors. J. Energy Chem. 54, 352–367 (2021). https://doi.org/10.1016/j.jechem.2020.05.058
C. Li, X. Zhang, Z. Lv, K. Wang, X. Sun et al., Scalable combustion synthesis of graphene-welded activated carbon for high-performance supercapacitors. Chem. Eng. J. 414, 128781 (2021). https://doi.org/10.1016/j.cej.2021.128781
Z. Yang, J. Deng, X. Chen, J. Ren, H.S. Peng, A highly stretchable, fiber-shaped supercapacitor. Angew. Chem. Int. Ed. 52, 13453–13457 (2013). https://doi.org/10.1002/anie.201307619
H. Sun, Y. Zhang, J. Zhang, X. Sun, H. Peng, Energy harvesting and storage in 1D devices. Nat. Rev. Mater. 2, 17023 (2017). https://doi.org/10.1038/natrevmats.2017.23
Y. Meng, Y. Zhao, C. Hu, H. Cheng, Z. Zhang et al., All-graphene core-sheath microfibers for all-solid-state, stretchable fibriform supercapacitors and wearable electronic textiles. Adv. Mater. 25, 2326–2331 (2013). https://doi.org/10.1002/adma.201300132
X. Wang, Z. Zhou, Z. Sun, J. Hah, Y. Yao et al., Atomic modulation of 3D conductive frameworks boost performance of MnO2 for coaxial fiber-shaped supercapacitors. Nano-Micro Lett. 13, 4 (2021). https://doi.org/10.1007/s40820-020-00529-8
C. Choi, J. Lee, A. Choi, Y. Kim, X. Lepro et al., Flexible Supercapacitor Made of Carbon Nanotube Yarn with Internal Pores. Adv. Mater. 26, 2059–2065 (2014). https://doi.org/10.1002/adma.201304736
L. Li, Z. Lou, D. Chen, G.Z. Shen, Hollow polypyrrole sleeve based coaxial fiber supercapacitors for wearable integrated photosensing system. Adv. Mater. Technol. 3, 1800115 (2018). https://doi.org/10.1002/admt.201800115
L. Wang, D. Shao, J. Guo, S. Zhang, Y. Lu, A MXene-coated activated carbon cloth for flexible solid-state supercapacitor. Energy Technol. Ger. 8, 1901003 (2020). https://doi.org/10.1002/ente.201901003
M. Hu, T. Hu, R. Cheng, J. Yang, C. Cui et al., MXene-coated silk-derived carbon cloth toward flexible electrode for supercapacitor application. Energy Chem. 27, 161–166 (2018). https://doi.org/10.1016/j.jechem.2017.10.030
L. Weng, F. Qi, Y. Min, The Ti3C2Tx MXene coated metal mesh electrodes for stretchable supercapacitors. Mater. Lett. 278, 128235 (2020). https://doi.org/10.1016/j.matlet.2020.128235
A. Levitt, D. Hegh, P. Phillips, S. Uzun, M. Anayee et al., 3D knitted energy storage textiles using MXene-coated yarns. Mater. Today 34, 17–29 (2020). https://doi.org/10.1016/j.mattod.2020.02.005
M. Hu, Z. Li, G. Li, T. Hu, C. Zhang et al., All solid state flexible fiber-based MXene supercapacitors. Adv. Mater. Technol. US. 2, 1700143 (2017). https://doi.org/10.1002/admt.201700143
N. Wang, J. Liu, Y. Zhao, M. Hua, R. Qin et al., Laser-cutting fabrication of MXene-based flexible micro-supercapacitors with high areal capacitance. ChemNanoMat 5, 658–665 (2019). https://doi.org/10.1002/cnma.201800674
X. Zheng, X. Zhou, J. Xu, L. Zou, W. Nie et al., Highly stretchable CNT/MnO2 nanosheets fiber supercapacitors with high energy density. J Mater. Sci. 19, 8251–8263 (2020). https://doi.org/10.1007/s10853-020-04608-4
G. Lee, J. Kim, H. Park, J. Lee, H. Lee et al., Skin-like, dynamically stretchable, planar supercapacitors with buckled carbon nanotube/Mn−Mo mixed oxide electrodes and air-stable organic electrolyte. ACS Nano 13, 855–866 (2019). https://doi.org/10.1021/acsnano.8b08645
H. Xiao, Z. Wu, F. Zhou, S. Zheng, D. Sui et al., Stretchable tandem micro-supercapacitors with high voltage output and exceptional mechanical robustness. Energy Storage Mater. 13, 233–240 (2018). https://doi.org/10.1016/j.ensm.2018.01.019
J. Yun, C. Song, H. Lee, H. Park, Y. Jeong et al., Stretchable array of high-performance micro-supercapacitors charged with solar cells for wireless powering of an integrated strain sensor. Nano Energy 49, 644–654 (2018). https://doi.org/10.1016/j.nanoen.2018.05.017
Acknowledgements
This work was supported by National Natural Science Foundation of China (51672308, 51972025, 61888102, 62004187), Hebei Natural Science Foundation of Hebei (E2019208280).
Funding
Open access funding provided by Shanghai Jiao Tong University.
Author information
Authors and Affiliations
Corresponding authors
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Shi, B., Li, L., Chen, A. et al. Continuous Fabrication of Ti3C2Tx MXene-Based Braided Coaxial Zinc-Ion Hybrid Supercapacitors with Improved Performance. Nano-Micro Lett. 14, 34 (2022). https://doi.org/10.1007/s40820-021-00757-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40820-021-00757-6